Search Documents

By John Durkin

Field studies have been conducted in a large number of coal mines throughout the U.S. to determine the effectiveness of electromagnetic techniques in locating men trapped underground following a mine disaster. Data from these tests have been used to generate models of expected signal and noise distributions as found above mines throughout the coal fields. These distributions have aided in placing the expected performance of a through-the-earth electromagnetic communications technique into a probabilistic framework. Results indicate an expected 45% probability of detecting a miner's signal from a depth of 1,000 ft, a depth which exceeds 903 of the coal mines within the U.S. and a 90% probability at a depth of 500 ft, a depth which exceeds 50% of the mines.

By C. W. Owings

Two problems perplex many coal-mine operators and employees. Is coal-mine dust harmful to breathe; and, if so, is it possible to keep the concentration below the danger point? The medical profession is not unanimous in its opinion of the danger of breathing bituminous-coal dust, but there appears to be ample and increasing evidence that coal-mine dust can be harmful if breathed in large enough doses for long periods. The question of controlling the dust at the point of formation is still unanswered in the minds of many in the mining industry. However, results of limited studies conducted by the Bureau of Mines in 9 bituminous-coal mines indicate that a full-shift average exposure of workers should not exceed about 20 million dust particles per cubic foot of air (m.p.p.c.f.) and that concentrations can be held within this limit without too much difficulty. Furthermore, these studies indicated that an exposure in the neighborhood of 40 m.p.p.c.f. should not be exceeded for an individual operation and that it is possible to hold within this ceiling.

Jan 1, 1957

By Thomas H. Dubaniewicz

The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory conducted a study of laser safety in potentially flammable environments. Researchers measured threshold igniting powers as a function of beam diameter for butane and propane-air mixtures by laser-heating targets placed on optical fiber tips using a 1064 nm laser. The minimum igniting powers for propane-air and butane-air were about 250 and 300 mW, respectively. Threshold igniting powers for propane-air were approximately proportional to beam diameter for beam diameters from 0.1 to 2.0 mm. Results suggest that relatively powerful beams may be used in these atmospheres without causing ignition, provided the beam diameter is controlled. Threshold ignition delay times using 91125 and 62.51 125 pm fibers were approximately proportional to the inverse square of the laser power. Ignition delays were about 45 ms or longer for laser powers up to 800 mW. Preproduction samples of a commercial optical fuse prevented ignitions under selected test conditions. A self-healing effect was observed for one sample. Comparisons are made with the results of other researchers. O 2006 Laser Institute of America. Key words: propane ignition, butane ignition, laser ignition, nonbeam hazards, fiber optic fuse

May 3, 2006

By John W. Finch

The Secretary of the Interior acting through the Bureau of Mines and the Geological Survey is authorized by the Strategic Materials (Public No. 117 - 76th Cong., Chapter 190 1st Sess.) to make investigation concerning essential minerals of which the quantities or grades obtainable from known domestic sources are inadequate. The Bureau of Mines, in carrying out its part of this program, may investigate deposits of such minerals in whatever manner may be necessary, in order to determine (1) the extent and quality of the are, (2) the most suitable method of mining and beneficiating it, and (3) the cost at which it may be produced. The essential objective in doing these things is to determine where and how supplies of minerals and metals of which domestic production is usually inadequate might be obtained in a national emergency, even though at higher cost than usual.

Jan 1, 1939

By D. Harrington

"A tabulation is printed below showing the accident record of the thirty-two mines of the Anaconda Copper Mining Co., in Montana, for the years 1915, 1916, 1917, 1918, 1919 and 1920, with summation for the six years. The table gives the number of shifts worked by each mine with the serious plus fatal accident rate for each 10,000 shifts worked.It is seen that in a total of 16,460,767.5 shifts worked by employees of the company's mines during this six-year period, there were only 2,005 serious and fatal accidents and of these, 200 were fatalities, leaving 1,805 serious accidents (a serious accident being one in which 14 or more days' time are lost). This is at a rate of 9,120 shifts per serious accident and at a rate of 82,304 shifts per fatality. Hence, if 300 days be adopted as a year's work, there would be one fatality per 274.3 years of work in these mines and one serious accident for every 30.4 years work.According to Bureau of Mines Technical Paper 286, (Metal-mine accidents in U. S. in 1919, by W. W4 Adams), during the years 1916, 1917, 1918, and 1919, the metal mines of the United States worked a total of 210,548,640 shifts and had 39,705 serious accidents. During the same years, according to the following tabulation, the mines of the above-mentioned company worked 11,958,978 shifts and had a serious accident rate of 0.995 accidents per 10,000 shifts worked. If the metal mines of the United States, working these 210,548,640 shifts, had this company's serious accident rate of 0.995 serious accidents per 10,000 shifts, the total number of serious accidents would have been only 21,000 or the country's metal-mine serious accidents would have been reduced nearly one-half, and there would be 18,705 fewer serious accidents than actually occurred."

Jun 10, 1921

By C. M. McCulloch

A series of geological surveys were completed in six coal mines in connection with a Bureau of Mines research program on methane control. The aim of these surveys was twofold: First, to study the overall geology of the coalbed, and second to use the resulting data to evaluate the influence of the geological characteristics of the coalbed on safe and efficient coal extraction. This report explains the advantages of geologic maps and fence diagrams in coal mining, and how the knowledge gained from such geologic investigations of mines can help control many underground problems.

Jan 1, 1975

By Richard L. Rains

The 15,770-acre Worm Creek Roadless Study Area is in southeastern Idaho about 8 miles (mi) west of the northern portion of Bear Lake. U.S. Bureau of Mines personnel examined the roadless, area during the summer of 1984. No mineral resources were identified within the study area. There were no mines or mining claims in the study area in 1984. However, the study area is blanketed with oil and gas leases, but no known productive horizons have been identified within nor nearby. The roadless area is in the Cordilleran fold-thrust belt and is underlain by Paleozoic and Mesozoic marine strata more than 50,000 feet thick. The trace of the Paris thrust fault is 2 to 3 mi east of the study area and has an eastward displacement of about 4 to 7 mi.

Jan 1, 1985

By Thomas M. Barczak

Longwall operators are again pushing the envelope in terms of life expectancy for longwall shields. State-of-the-art shields are now expected to last more than 60,000 loading cycles, twice the life expectancy compared with those of a decade ago. A review of trends in shield design shows that shields continue to increase in both size and capacity. Some state-of-the-art shields now weigh over 30 tons and provide up to 1,200 tons of support capacity. Although life expectancy has increased and modern shields are structurally more reliable, premature failures do still occur. This paper provides an engineering and operational assessment of shield design and provides key points to observe in what causes premature shield failures. Design practices to improve structural margins of safety that will prevent premature failures from occurring are also examined. A survey of recent shield failures is provided, as well as trends in shield design and how they might impact the performance and longevity of a shield. Hydraulic failures are more common than structural failures. Although hydraulic failures occur on all aging longwall shields, they often go undetected for long periods, resulting in degraded support capacity that can lead to serious ground control problems. The fundamentals of shield hydraulics are described in order to evaluate hydraulic failures that plague all shields at some point in their service life, and practical methods to detect hydraulic failures are examined. The paper concludes with recommendations for inspecting damaged shields and safety precautions regarding their continued use.

Jan 10, 2000

By Alvin M. Cummings

"INTRODUCTION During July and August 1943, the Bureau of Mines undertook an investigation of the Trego lead-zinc mine, near the town of Platteville in Grart County, Wis. as part of a general investigation of the zinc-producing area of southwestern Wisconsin. The work was done when every effort was being made to increase the production of metals important to the nation's war program.The Bureau of Mines completed eight churn-drill holes and sampled mineralized faces in the mine workings to determine if further exploitation was justified in an area between the mine and a zone previously drilled to the east.Following the investigation described herein, intermittent operations were resumed. Except where otherwise stated, this report describes conditions only to the time of completion of the Bureau of Mines investigations.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and performs beneficiation tests.The investigation described in this report was conducted under the immediate supervision of the author and 0. W. Terry, mining engineer of the Bureau of Mines, with the assistance and advice of E. D. Gardner, re¬gional engineer, and E. P. Barrett, district engineer. Final data were prepared under the direction of Paul Zinner, acting chief, Minneapolis Branch, Mining Division.A. V. Heyl, Jr., and A. F. Agnew of the Federal Geological Survey cooperated with the Bureau's engineers and made lithologic studies required during the drilling program.The cooperation of W. N. Smith and O. E. DeWitt of the Vinegar Hill Zinc Co. and Francis Piquette of the Piquette Mining Co. facilitated the investigation to a great extent."

Mar 1, 1948

By Stephen Gerard Sawyer

The Bureau of Mines developed a method for analyzing elastically certain types of protective cabs and canopies used on underground electric face equipment. The method is based on plane frame theory, and to be amenable to analysis by this method, cabs and canopies must contain symmetry about one plane. Additionally, protective structures with one or more top members in the long direction that do not frame into the columns should be approximately twice as long as they are wide and have two or more internal top members in the short direction. The assumptions and limitations of the plane frame method as regards analysis of three-dimensional cabs and canopies are discussed. A step-by-step procedure for application of the plane frame method is given, and three example canopies are analyzed following this procedure. Elastic strengths calculated for the three example canopies compare within 10 percent of those computed by the more complicated space frame analysis. Formulas employed in plane frame analysis of cabs and canopies are given in the appendixes.

Jan 1, 1973

By Greenwald, H. P

The Bureau of Mines has been conducting experiments on the explosibility of coal-dust in the experimental mine for more than 17 years. The results have been published from time to time3, and a forthcoming technical paper4 will summarize the results and discuss them in some detail. The present paper will be limited to a statement of the more important facts that these researches have discovered.

Apr 1, 1929

Develop a full-length-anchored roof bolt that is economical, nontoxic, nonflammable, and non-allergenic. Approach Grout roof bolts with a storable mixture of ultra-fast setting inorganic cement and water. How It Works A loose mixture of dry cement powder, and pinhead-size water droplets encased in waxy globules, are pack-aged in sausage shaped cartridges for storage and use. After the cartridge is inserted Into a drilled hole, the roof bolt is thrust In and rotated to mix the cement and water. The cement hardens in seconds, providing usuable anchoring strengths in minutes. Prior to filling of the sausage shaped cartridges, the microcapsules of water are Intimately mixed with the dry cement. The currently used grouting consists of a mixture of one part water (minimum) with three parts alpha-type gypsum cement and a minor amount of accelerator.

Jan 1, 1978

By S. B. Robertson, D. R. Dolinar, G. E. Hinshaw, G. M. Molinda, D. M. Pappas

Rock falls in coal mines cause many injuries each year. Most of these injuries are not caused by major roof collapses, but from falls of smaller rocks from the immediate top or roof skin. Even though safety professionals and mine operators strive to reduce these types of injuries, there has not been a substantial decrease in the rock fall injury rate over the past decade. Various surface controls are used in mines to control the roof skin. One control that has proven to be very effective is roof screening. Roof screen effectively controls roof skin and provides a high roof surface coverage. Although many mines are reluctant to use screen for primary skin control because of the additional costs of time and materials, others are having great success at controlling both the costs and surface rock. In this study, injury data are presented that show a dramatic reduction in roof skin injuries when screening is used. Much of this success is due to the protection from falling rock that the operators receive from roof screen. Five case studies in which roof screen was used are presented along with the associated costs of materials, impact on bolting advance rates, and potential ergonomic risks. The effects of roof screening on skin control and safety are also included. Finally, this paper provides information about best practices and features of roof bolting machines that affect production and safety.

By W. A. Cole

The sulfur shortage that existed during the Korean conflict stimulated interest in coal measures as possible sources of sulfur. One of the areas brought to the attention of the Bureau of Mines was in Marion County, Iowa, where comparatively high-sulfur coals and other marcasite-bearing strata were known to occur. A Bureau of Mines engineer inspected the marcasite occurrence on December 4, 1954; this prompted further work on the Iowa coals and associated formations as a source of iron sulfides. An investigation of the Iowa high-sulfur coals was undertaken including core drilling, field reconnaissance, and compilation of data pertinent to consideration of the following: 1. Upgrading Iowa coal by mechanical cleaning and the feasibility of recovering sulfur from coal brasses. 2. Possibility of processing the high-sulfur coals by adaptation of methods employed in processing industrial gases to produce sulfur and sulfur products. 3. Possibility of finding concentrations of iron sulfides in associated rock formations in sufficient quantity for economical recovery.

Jan 1, 1957

By R. W. Freedman

The Bureau of Mines has developed a gas chromatographic method for the rapid and accurate determination of oxygen, nitrogen, carbon dioxide, methane, and, if present, carbon monoxide in mine air. This method replaces such presently used gas-reaction types as the Haldane or Orsat analysis, offering advantages in terms of precision, accuracy, speed, and convenience.

Jan 1, 1968

Identify abnormal low-frequency blast vibrations. Develop blast design procedures for such adverse vibration cases, including the selection of delay times based on ground conditions, vibration frequency, and structural response. The Problem Research by the Bureau of Mines and others has demonstrated how structural response and the potential for cracking and other damage depends on blast vibration frequency in addition to particle velocity amplitude. The Bureau has published recommended criteria for blasting near low-rise residential-type structures; criteria that specified frequency-dependent amplitudes. The typical vibration frequency from surface mine and quarry blasting is 20 hertz (Hz). Sites have been found, however, that regularly produce ground-roll-type waves with frequencies as low as 4 Hz. The most serious cases arc those where vibration frequencies fall in the natural frequency range for structures of 4 to 12 Hz. Such vibrations have a higher potential for causing, damage to residential structures, particularly at the low end of this frequency range, because of the resulting high strains these frequencies produce in structural materials.

Jan 1, 1990

Improve the safety and reduce the cost of longwall entry support. Approach Replace the conventional wood cribbing with stronger, non-rotting and lower cost cribbing made of steel-fiber-reinforced (SFR) concrete. How It Works Conventional concrete can suddenly fail under excessive compression loads, but adding steel fibers to the concrete, before it is mixed with water, changes the failure mode to a gradual and controlled failure characteristic similar to wood. A system for making SFR concrete crib blocks was designed and developed (or use in constructing walls and cribs to support coal mine roofs. The SFR concrete cribbing is stronger and stiffer than wood, and avoids wood's disadvantages of: flammability, deterioration under chemical or bacteriological attack, methane generation, and relatively high cost. Use of SFR concrete also allows freer movement of miners, equipment, and ventilation air, because much less volume of SFR concrete is required than wood for a given amount of support, and because the roof-to-floor closure is greatly reduced by the stiffer supports.

Jan 1, 1981

By Lloyd A. Morley

To reduce safety and production problems, it is essential that the electrical operating characteristics of coal mining equipment and their electrical subsystems be clearly understood. The Bureau of Mines and the Pennsylvania State University have developed techniques to monitor and analyze several of the critical parameters. A unique system for measuring traction locomotive consumption at the machine has been assembled and utilized. Conclusions from 27 continuous miners show that voltage levels are directly tied to machine efficiency. The Bureau of Mines and Pennsylvania State University, along with West Virginia University, are currently monitoring and accessing mine power transients. Results exhibit that voltage transients of three to five times the line -to-line value are common on underground distribution systems.

Jan 1, 1975

To minimize support costs and to improve ground control by improving wood-crib design and utilization through the development of engineering methods that will match the placement and performance of the wood cribs to the load conditions imposed by the mine environment. Background While wood cribs are used extensively to stabilize mine openings, their utilization is often based on historical practice or trial-and-error rather than on engineering design. This has led to conservative crib utilization where more capacity than is necessary is employed or inadequate capacity is provided when mine conditions worsen. Critical design parameters, such as the stiffness of the support structure, are often ignored. Optimum crib design and employment is becoming increasingly important as the utilization of wood cribs increase due to the growth of longwall mining, and as the cost of wood continues to rise. A single longwall operation will spend as much as a million dollars per year on the support of the gate roads.

Jan 1, 1994

By Oliver C. Ralston, Foster Fraas

"INTRODUCTION The predominant characteristic of powdered mica is the thin -plate shape of the particulars, and the thinner the plates, the more enhanced is this characteristic. Consequently, it is frequently desirable to grade mica according to the thickness of the plates. Concerning the various possible methods for grading mica, very little has been published. There is also no information on the relative quantities of mica per given range of plate thickness. This paper presents a graphical method that shows how these quantities are distributed and how the different methods of grading compare.CUMULATIVE BULK DENSITYBulk density, which is an indirect measure of the plate thickness, was determined in a small cylindrical cup of 3.37 cubic centimeters volume. The mica was placed in the cup under a standard procedure. The densities thus measured checked these determined in a 273 cubic centi¬meter cup with less than a 2 percent error.In calculating cumulative densities it is important to know how they are averaged. In any grading operation the bulk density of a series of fractions is determined. Starting with the lowest density fraction, the cumulative percent under-density can be calculated through the various fractions. It is possible that quantity may be measured by volume or weight and that the averaging may be done by a number of methods. However, experimentally it has been shown that the quantity must be by volume and that the averaging must be arithmetic. This is illustrated in table 1, in which the calculated and actual bulk densities are listed."

Sep 1, 1942