Search Documents

Determine what diameter piping is necessary to obtain sufficient water flow to spray nozzles used for dust suppression. Approach A simplified, diagrammatic method of calculating the flow of water through a proposed system consisting of a supply line and two banks of spray nuzzles is outlined. How It Works The pressure versus flowrate of the supply at the tapping point must be known or measured. The supply curve of typical city water at a 1 ¼ -inch pipe outlet is shown by the lowest curve in Figure 1. A supply curve for a typical pump fed from an open sump is shown by the middle curve. The combination of these, the supply curve of a pump fed by the city water supply is shown by adding the lower two curves to get the upper curve. A pump supply curve showing flowrate versus pressure is usually supplied by the manufacturer. The water supply line flow curve can be determined by measuring the time required to fill a 55 gallon barrel at various valve settings to determine flow, and by measuring corresponding pressures at the valve with a gauge.

Jan 1, 1979

By Harold L. Rhodes

Vapor-liquid equilibria data for 65-34-1 and 25-27-48 mole percent helium-nitrogen-methane mixtures are presented for 12 temperatures from 76.5° to 164° K and pressures from 100 to 1,200 psia. These data were obtained in a windowed phase equilibria cell equipped with a vapor recirculating pump. Isobaric and isothermal K-values are plotted for both mixtures. Two isometric plots are included.

Jan 1, 1972

Determine the extent to which remote-sensing techniques, primarily lineament analysis, can be used to identify geologic structures that may affect the location and migration of subsidence over abandoned underground coal mines in the Colorado Springs, CO, area. Compile data using a geographic information system (GIS) to allow efficient and reproducible comparisons and analyses. Background The basis for evaluating abandoned mine land (AML) sites with remote-sensing techniques comes from past and ongoing Bureau ground control research using remote-sensing data to identify potential hazards caused by geologic structures (faults, joints, etc.) above active underground coal mines. Research showed that lineament (linear feature) analysis of Landsat Multispectral Scanner (MSS) images could indicate locations of fractures and fracture trends that had varying, but significant, impacts on the stability of mine openings. Such geologic structures should be identifiable over abandoned mines as well. If fractures are present, even if they arc not faults, they should represent areas of potential instability over these mines and, therefore, should tend to localize subsidence when it occurs, particularly for deep and moderately deep portions of mines.

Jan 1, 1992

By Frank E. Cash

The iron-ore ranges in the Lake Superior district are the liarquette in Michigan, Menominee and Gogebic in Michigan end Wisconsin, and the Vermilion, Mesabi, and Cuvuna in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. Accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year but closely approximate each other over a period of years. During the 4-year period 1940 to 1943, inclusive, 323,667,599 long tons of iron ore was shipped from the Lake Superior district.4/ Michigan and Wisconsin shipped 65,386,608 tons, or 20.2 percent of the total, and employed approximately 15,000 men; Minnesota shipped 258,280,991 tons, or 79.8 percent of the total, and employed approximately 10,000 men. The tons produced per man employed is much, greater in Minnesota than in Michigan and Wisconsin owing to the large open-cut production in Minnesota.

Jan 1, 1945

By James J. Olson

The Bureau of Mines recorded peak particle-velocity levels and vibration frequencies to determine the nature and intensity of ground vibrations for tunnel blast rounds at the NORAD Complex, Colorado Springs, Colo. Previous Bureau of Mines studies in quarries and underground mines had shown that scaling (dividing) the distance from the blast by the square root of the charge weight removed the effect of the various charge weights on vibration amplitudes. The analysis of variance tests performed on the NORAD vibration data, however, indicated that the cube rather than square root scaling exponent grouped the data more effectively. The empirical propagation equation, V = 560 (D/w1/3)-2.04, where V is the maximum peak particle velocity in inches per second, D is the distance from the blast in feet, and W is the zero-delay charge weight in pounds described the attenuation, with distance, of the particle velocities from the tunnel blasts in the Pikes Peak Granite of the NORAD Complex.

Jan 1, 1972

By James A. West

THE South Asian countries of India, Ceylon, Pakistan, Afghanistan, Nepal, Bhutan, and Sikkim have a large variety of mineral resources; however, in spite of mineral industry growth during 1964, development of resources remained far short of possible development, and, in terms of value of trade in minerals, the area remained a sizeable net importer. India's mineral industry is by far the most significant; its minerals production in 1964 accounted for more than 90 per cent of the total value of all minerals produced in the area. The total value of all minerals produced in South Asia in 1964 was only about 1 percent of the area's estimated gross national product of $55,125 million. Despite the rather small current contribution of minerals to the economy, development of mineral resources figures prominently in plans for the industrial development of the nations of this area.

Jan 1, 1966

By Robert J. Willard

This chapter includes tables from 1983 that were not available in time for publication of the 1983 Minerals Yearbook, but does not include corresponding tables for 1984. The value of raw nonfuel minerals produced in the United States during 1984 was estimated at $23.2 billion, an increase of $2.1 billion over the value for 1983. This is the second consecutive year that the value has increased, and except for a decrease in 1982, the value for each year has increased since 1971, or 12 out of 13 years. In 1984, 16 out of 21 metal commodities increased in output while 5 metals decreased; 14 metals increased in value and 7 decreased. Of 46 nonmetal commodities. 37 increased in output while 7 decreased and 2 remained unchanged; 35 nonmetals increased in value and 11 decreased. These statistics are grounds for continuing the cautious economic optimism expressed in 1983. Despite the note of optimism, however, numerous problems plague the mining industry, weakening its stability and inhibiting its growth potential. The problems are a complex mix of international and domestic factors that have been building in the recent past, but have become even more troublesome in 1984.

Jan 1, 1985

By J. G. Schoning

The Holmes Safety Association is an offspring of the Joseph A. Holmes Safety Association which was organized in Washington, D. C., in 1916 at a meeting of representatives of twenty-four leading mining associations connected with every branch of the United States mineral industries. The purpose of the meeting was to do honor to the memory of Joseph A. Holmes, one of the founders of the United States Bureau of Mines and its first director, whose death had occurred the year before on July 12, 1915. In deference to what was believed would have been the expressed wish of this great humanitarian and benefactor of the mineral industries, it was decided to establish a national safety organization to cover the mineral indus¬tries exclusively; out of respect for his memory and service, the organization was named the Joseph A. Holmes Safety Association. On receiving requests from several mining districts, in 1922 a number of chapters ware established in several mining States.

Jan 1, 1929

By W. J. Fene, H. B. Humphrey, J. J. Forbes

"INTRODUCTION Loss of life from coal-mine explosions in the United States in 1949 was the lowest in any year since before 1870. Although fatality reports from coal nines before 1910 were incomplete,' the explosion fatalities from single disasters or individual States exceeded the 1949 total in each year as far back as 1870, when the records become fragmentary. Since 1890, the only other year in which fewer than 35 were killed was 1946, with a total of 32. Figure 1 shows the total yearly fatalities from explosions in all coal mines and those in anthracite mines alone since 1870. The fatalities in bituminous coal mines were not completely reported before 1910, but enough reports were issued by major coal-producing States to compile reasonably representative figures back to 1885. Any corrections would be additions to these totals.The reason for the moderate total of 46 explosion fatalities in 1948 and the low total of 8 killed in 1949 is thought to be the serious and careful attention devoted to elimination of coal-mine explosion hazards after the disastrous explosions in 1947. The standards now being observed generally with respect to ventilation, rock-dusting, and inspections for gas are better than those found earlier in even the mines having the best reputations for safety. Exceptions are still numerous, but they are fewer, month by month, because of the pressure of Federal and State inspections and a changing conception of the hazards that should not be permitted underground. The prevailing precautions have not eliminated all ignitions of gas or dust, but they have limited propagation to small explosions and have prevented serious loss of life.The number of ignitions (14) reported for the year was less than the average (24) for the 5 years 1944-48 and only half the average for the fiscal years 1929-44. Another favorable factor is that Bureau of Mines representatives were probably in closer contact with both small and large mines in nearly all coal-mining districts. Inspectors now assigned to individual districts are better able to keep informed on the happenings and the progress of safety in their districts. In 1948, one-fourth of the explosions were in mines that employed fewer than 10 men; this condition was duplicated in 1949."

Jul 1, 1950

By W. W. Weller

Low-temperature heat capacity measurements were conducted, and entropies at 298.15° K were evaluated for sodium monomolybdate (Na2Mo04), magnesium monomolybdate (MgMo04), and calcium monomolybdate (CaMo04). The 298.15° K entropy values were sodium monomolybdate, 38.1±0.3 cal/deg mole, magnesium monomolybdate, 28.4±0.2 cal/deg mole, and calcium monomolybdate, 29.3±0.2 cal/deg mole.

Jan 1, 1963

By G. M. Molinda, J. P. Ulery

Since 1970, abnormally high methane emissions have been observed in eastern sections of the Federal No. 2 Mine operating in the Pittsburgh Coalbed in northern West Virginia. The nature and volume of these emissions indicate a source other than the coalbed. An investigation was undertaken to delineate probable methane sources. Gas well information and stratigraphic correlation of corehole data indicates that a sandstone directly above the main coalbed is an additional source of methane emissions. The sandstone body appears to be an ancient stream channel, infilled with fine-grained sand and organic matter. Coalification of the organic matter produced methane as a byproduct. Additional methane presumably migrated into the sandstone unit from the subjacent coalbeds. The methane became trapped in the porous clasticunit by the surrounding impermeable strata. Mine development near this unit creates a significant pressure gradient, triggering abnormal methane emissions into the mine along naturally occurring fractures. Pre-development methane drainage of the sandstone could be accomplished by completing vertical boreholes along its trend.

Jan 1, 1984

Heavy liquids have come into use in ore-dressing investigations, as they make possible the separation of an ore into its specific-gravity components. A paper containing a general dissertation on heavy liquids has been written by John D. Sullivan,4 and the practical application of heavy liquids is explained by Box and Crabtree5. Some heavy liquids become discolored after continued use, and the lack of transparency impairs their value. Since they are fairly expensive, reclaiming is desirable. This paper briefly discusses the preparation and care of some of the more common heavy liquids.

Jan 1, 1928

By E. D. Gardner

"A fire hazard exists in nearly all mines. Progressive mining companies recognize this danger and take all possible precautions to prevent any conflagrations, but in spite of such safety measures, mine fires do occasionally occur and endanger life and property. In order to be prepared for such an emergency, miners are trained in the use of self-contained breathing apparatus and the necessary fire-fighting equipment is kept on hand. Men trained to wear breathing apparatus can penetrate workings full of poisonous fumes, but in order to successfully combat fumes or to rescue miners, the rescue crews must be trained in fire-fighting operations and know how to proceed with a minimum loss of time when they get to the scene of action.In order to perfect fire-fighting plans and to train men of the Globe-Miami district under conditions approximating those found at an actual mine fire, mine-reseue maneuvers were held at Globe, Arizona, on October 17-20, inclusive. The work was done under the direction of Orr Woodburn, director, and his associates of the Globe-Miami District Mine Rescue and First Aid Association. He was assisted by Albert Tallon, safety engineer, and Herbert Finnegan of the Old Dominion Co.; Herbert Hodson, safety engineer for the Inspiration Consolidated Copper Co.; A. 3. Martinson and J. M. Harrington of Car One, and F. D. Gardner of the Southwest Station, Bureau of Mines. Invitations were issued to mining men likely to be interested and representatives of mining companies from other districts were present and observed the work.The Globe-Miami District Mine Rescue and First Aid Association is maintained by the mining companies in the district and each company contributes to the organization's support in proportion to the total number of men on the pay roll. A central station*, between Globe and Miami, has been established and a truck with 10 sets of 2-hour self-contained breathing apparatus and the necessary accessories is always in readiness to respond to a call to any of the mines in the district. Besides being in readiness for emergency work, the station employees train men in the use of mine-rescue apparatus and in first-aid to the injured at the mines of the association. The Globe-Miami Mine Rescue organization has been developed to high point of, efficiency under Mr. Woodburn's direction and is one of the best in the country. The three largest mines of the district such maintain a crew of 15 men trained in the use of breathing apparatus, and other mines keep crews of 5 men each."

May 1, 1923

By D. Harrington

In recent years over 100,000 persons have been killed annually in the United. States by accidents; about one-fifth of these have been workers in some of our industries; about one-third have been killed by motor vehicles; about another third have mot death in home accidents, chiefly falls, burns, scalds, explosions, poisons, asphyxiations, suffocations, cuts, scratches, and so forth; and the rest have been killed in public accidents, excluding those caused by vehicles but including accidents on railroads or electric cars, drowning, and deaths by firearms and. other means. Definite statistics on nonfatal accidents are not readily available, but at least 10,000,000 fairly serious accidents probably occur in the United States annually. The latest industrial-accident statistics are obtainable from 1935 National Safety Council publications, in which annual industrial fatalities are divided about as follows (in round numbers): Agriculture, 4,500; trade and service, 4,500; construction, 3,100; transportation and public utilities, 2,900; manufacturing, 2,600; mining, quarrying, petroleum, etc., 1,900.

Jan 1, 1938

By John S. Berber

Tar produced as a byproduct from low-temperature carbonization of coal contains only small amounts of valuable lower boiling tar acids but relatively high percentages of high-boiling tar acids. These high-boiling tar acids are characterized by a high degree of alkylation and can be converted into the lower boiling homologs by catalytic treatment to remove the alkyl groups or decrease their chain lengths.

Jan 1, 1965

By A. Mayton, A. Brien, W. Porter, O&apos

In 2004, management at Unimin's Gleason, TN operation began implementing ergonomic interventions specifically targeted to reduce risk of musculoskeletal injuries (MSIs). Together with corporate and site management, Unimin identified work site hazards and began to modify work practices/equipment. Some interventions were relatively simple and were implemented immediately. Others, like improvements to a mobile shredder, were more complex but were eventually resolved through a participatory approach with employees, management, manufacturers and NIOSH. This paper discusses ergonomic interventions that were successfully implemented using a bottom-up approach to reducing the risk of injury.

Investigate the use and placement of lightweight concrete to improve ground control technology in deep mines where deformation occurs under heavy ground conditions and where there is danger of rock bursts. Approach Investigations of lightweight concrete properties and placement methods were conducted in the laboratory and in the field. Three test sections were completed: a monolithic, portal-type structure with integral walls and arch constructed aboveground; an underground test section constructed in a mine drift using plywood forms; and a test section constructed in a mine drift using an air-supported formwork. In the two underground test sections, the light-weight concrete was placed using a piston pump with concrete discharge line. A cooperating mine also used lightweight concrete, in the density range of 25 lb/ft3, to replace timber blocking in a raise preparation structure (the enlarged area across a vein where chutes and manway access arc placed). Other experiments included the use of precast lightweight concrete blocks in situations where ground support was needed, such as fur mine, ventilation doors, stoppings, and barricades.

Jan 1, 1990

By L. E. Schultze

As part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines devised a processing sequence for recovering uranium from carbonaceous ores. Uranium extractions of 97 pct were obtained by contacting the ore with a solution containing 400 grams of ferric sulfate hydrate in 200 ml water for 3 hr at boiling temperature (96° C). Uranium was recovered from the leaching solution by solvent extraction with tri-issooctyl amine. The barren ferric sulfate solution was recycled to the leaching system. The leaching process resulted in no detectable dissolution of carbonaceous material from the ore. Work on the project was terminated in 1978 because of a transfer of responsibility to the U.S. Department of Energy.

Jan 1, 1981

Provide an operator cab to assure protection, comfortable use of controls, and good visibility. Approach A cab which raises and lowers by pivoting about d horizontal axis was Installed on two S&S cleanup tractors and tested in two underground working mines. How It Works Hydraulic cylinders actuated by a lever inside the cab cause the cab to pivot about a horizontal axis. This action raises or lowers the cab height. The total cab excursion is 14 inches. A release valve in the hydraulic system allows the cab to lower automatically if struck by a roof load or overhead obstruction. The pivoting action of the cab is engineered so that the operator maintains comfortable use of all controls at all cab heights. The movement is such that the angular relationship of the operator's ankles With the tram and brake foot controls IS consistently within 90 to 100 degrees. Figure 1 outlines the approximate position of the operator at three cab elevations.

Jan 1, 1977

By Robert P. Vinson, Fred N. Kissell

This report describes three coal mine ventilation studies by the Bureau of Mines in which sulfur hexafluoride (SFG) was used as a tracer gas. One of these studies was conducted to determine air movement and leakage in a sealed area. Another was run to determine the ventilation efficiency of a bleeder system. Finally, a study was made of air leakage across permanent stoppings of parallel intake airways. These studies proved sulfur hexafluoride to be a useful addition to the equipment commonly used in coal mine ventilation analysis.

Jan 1, 1976