Search Documents

By Pedro Lilienfeld

The objective of this program was the development, design, and fabrication of six personal-sized completely self-contained dust monitors capable of real-time as well as time-averaged monitoring of the concentration of respirable particles in coal mines, in the range of 0.1 to 100 mg/m3. The operation of these monitors is based on light scattering and passive air sampling. The design stressed overall miniaturization, ruggedness, simplicity and versatility. These instruments incorporate a single-chip CMOS microprocessor to perform all signal processing, data display and storage, and timing functions. The overall dimensions of these devices are, approximately, 10 by 10 by 5 cm.

Jan 1, 1982

By Robert C. Dyni

This report details the investigation of multiple-seam longwall subsidence conducted by the U.S. Bureau of Mines from 1978 to 1989. A field investigation monitored ground surface movements over four upper-seam longwall panels and six lower-seam panels. The characteristics of the subsidence occurring as a result of mining these panels are examined; in particular, the angle of draw, subsidence development, total magnitude and areal extent, and critical width are evaluated and discussed. Comparisons are also made between the characteristics of multiple-seam longwall subsidence and single-seam longwall subsidence that occurred at the same site.

Jan 1, 1991

By R. L. Grant

The Bureau of Mines developed two new gap-sensitivity methods for explosives, and especially permissible explosives, to overcome certain disadvantages of the present routine half-cartridge method. The revised methods are based on the statistical up-and-down method and give more useful measurements of the 50-percent' gap values than the nonstatistical routine method. The new methods use full cartridges and incorporate certain physical improvements such as the use of cardboard tubes for containing the explosives and coal dust gaps to simulate actual mining conditions. A total of 60 samples of permissible explosives were evaluated simultaneously with the 2 improved methods and with the half-cartridge method

Jan 1, 1967

By Victor E. Kral

The Modarelli iron deposit , formerly known as the Requa iron deposit , is 44 miles by road south of Palisade , Nev . , on the Southern Pacific and Western Pacific Railroads . Construction of 10 miles of new road, which is necessary in case the property is exploited , will reduce this distance to about 28 miles . The deposit was discovered in 1905 , and patent was obtained in 1907 . The present owners obtained title to the property in recent years by paying the delinquent taxes . There has been no production . The ore deposit is a replacement of a Tertiary volcanic believed to be a rhyolite . Except for evidence of slight shearing , the deposit has no apparent structure . Hematite is the principal ore mineral ; it is fine-grained and is associated with very fine-grained apatite and unidentified minerals assumed to be alteration products of residual rhyolite minerals .

Feb 1, 1947

By Ellis S. Hertzog

The material published in this report is part of a special study of some of the chemical and physical properties of Alabama coals. The complete study included friability and grindability determinations, high and low temperature assay distillation tests, and ash fusion-temperature determinations. Proximate and ultimate analyses and. calorific values of the coal samples also were obtained. This paper is concerned only with grindabilities, although proximate analyses have been included to give a better picture of the problem as a whole. The growing interest in grindabilities of coals is a result of the increase in use of pulverized fuel in REscent years. The tenative ball-mill grindability method D409-35T4/was used in making all the determinations. The method of sampling and the technic of the testing procedure is described in Considerable detail in this report because the procedure was established quite recently. The ball-Mill grindability index is a measure of the ease with which coal may be ground, which may be an important factor in estimating pulverizing costs. Up to the present time few data on the grindability of Alabama coals have been published. The data in this paper show that the Warrior and Cahaba fields exhibit a wide range of grindability in their coals. The mines tested are well distributed throughout the productive areas of these fields, and it is possible to make rough estimates of the grindabilities of coals not listed in this report from the data given for mines situated in the same vicinity. ACKNOWLEDGMENTS This study was conducted at the Southern Experiment Station of the Bureau of Mines in cooperation with the University of Alabama. The Alabama liming Institute was of great assistance in furthering the investigation, and the work was undertaken largely as a result of its request that the Bureau of Mines should make certain studies of Alabama coals. Grateful acknowledgments

Jan 1, 1938

By C. J. Thompson

This Bureau of Mines study describes the preparation of sulfur compound concentrates boiling from 225° to 400° C, and reports the sulfur types detected in these concentrates by low-voltage mass spectrometry (LVMS). Existing LVMS methods were extended; the procedures described should be generally applicable to high-boiling petroleum distillates and concentrates as a preliminary means of narrowing the number of factions to be considered for more detailed separation and identification studies. The following major sulfur compound constituents of petroleum are indicated by the data: benzothiophenes, dibenzothiophenes, naphthanothiophenes, naphthenobenzothiophenes, and homologs and isomers of these. Cyclic and chain sulfides comprise a significant portion of the gas-oil range sulfur compound types. The presence of some classes of sulfur compounds containing two sulfur atoms per molecule was indicated.

Jan 1, 1966

By John D. Sullivan

The present article is one of a series which is being prepared by the Southwest Experiment Station of the United States Bureau of Mines in cooperation with the Department of Mining and Metallurgy, University of Arizona, Tucson, Ariz., of papers dealing with factors involved in the leaching of copper ores. A knowledge of the time required to dissolve the various copper minerals present in ores, as well as of the consumption of leaching reagents is very desirable, because with the decrease of the Nation's total tonnage of sulphide ores increasing attention is being given to the recovery of copper by leaching methods from low-grade disseminated ore containing both oxidized and sulphide minerals. As leaching has already been applied with success and profit, this study was undertaken to determine certain fundamental characteristics that are applicable to all ores suitable for leaching.

Jan 1, 1929

By Raja V. Ramani, Wilson Miola

"The potential health effects of quartz-bearing airborne dust in mine and mill atmospheres point to the need for the quantification of quartz content in the source material for determining the source-sink relationships and for choosing applicable control measures. While a standard method exists from a regulatory point of view for the sampling of coal mine atmospheres for determining (i) respirable dust concentrations and (ii) the amount of quartz in the samples, there is no generally accepted standard method for quartz analysis in bulk samples of coal and host rocks. Generally, the bulk sample is reduced to a powder for producing quartz analysis samples. Extensive controls arc necessary to ensure representativeness of the analysis samples when these are very minute fractions of the bulk samples. Since the amount of analysis sample is not limited, alternative methods for quartz analysis may also be tried. It is, however, necessary to adopt a procedure which will satisfy several statistical requirements to guarantee representativeness of the quartz analysis samples.In this paper, the important factors in the preparation of quartz analysis samples from the host rocks and bulk samples are discussed. The method developed to prepare the analysis samples is outlined. The results of application of the procedures are presented. The procedure developed for quartz analysis sample preparation is based on sound statistical foundations. The procedure has been validated for reproducibility and homogeneity.The current methods used for quartz analysis in powders are the P-7 infrared spectrometry and quantitative X-Ray Diffraction (XRD). Both have similar restrictions concerning the sample characteristics and operational problems, which arc intrinsic to radiation beams, device geometry, mechanics and controls of the radiation behavior. Although improvements can be made in the spectrometers and diffractometers, some of the most important steps are the procedures for analysis sample preparation from bulk samples and for calibration of the instruments. The sample preparation process is often referred to as one of grinding and sizing the bulk sample to generate the powder for the scanning devices. The particle sizes are referred to and their influence emphasized but the representativeness of the sample is assumed. Assuring sample representativeness during the sample preparation procedures is critical.For the sampling of airborne respirable dust in coal mines, the collection devices, the collection procedures and the analysis procedures are defined. This is not true for bulk samples where weights must be reduced thousands of times to generate the analysis samples for the scanning devices. The specifications to be developed may include bulk sample amount, sample reduction procedures, sample particle size distribution and sample amounts. However, the common problem of insufficient sample amount which is often encountered with mine airborne dust samples need not exist for bulk samples. Further, the same bulk sample can yield analysis samples for several experiments. The latter, of course, requires sample homogeneity.Three concepts are important in the selection of any procedure for sample preparation and analysis. These arc accuracy, reproducibility and representativeness. The adopted procedure has to guarantee a homogeneous sample representative of the population, a defined level of accuracy and reproducibility. Important statistical concepts are embedded in these requirements, particularly with respect to estimation and dispersion errors. Accuracy and reproducibility are totally different though not independent concepts. Estimation is related to accuracy and the true value. Dispersion is related to reproducibility and is measured by the classical statistical standard deviation of the distribution of a series of measurements or analysis performed over the same lot or analysis sample. The dispersion variance (or dispersion error) does not tell a"

Mar 1, 1992

By J. F. Barkley

[There is a general concept in the, coal trade that the moisture- and ash-free B.t.u. of coal from the same seam, and. surely from the same mine, is substantially a constant; that calculation of the -moisture- and ash-free B.t.u. value from the proximate analysis and B.t.u. determined in the laboratory will reveal whether a coal came from a given area or sears; and that, having this constant, the B.t.u. value of a coal sample can be calculated fairly closely upon a dry or as-received basis from the moisture and ash values of its proximate analysis.]

Jan 1, 1941

By A. F. Cohen

When location guidelines are followed in choosing sites for fixed point velocity transducers for use in underground coal mine monitoring, mine air turbulence intensities <11% are generally expected at those sites. The objective of this Bureau of Mines investigation to determine the effect of turbulence intensities <11% on vortex shedding sensors and transducers. Measurements were made at velocity levels of interest for underground coal mine monitoring use (?200, ?500, ?1,000, ?1,500 ft/min). The effect of grid-produced turbulence intensities (2% to ?14%) on the output of vortex-shedding air-velocity transducers was less than ±10%.

Jan 1, 1985

By J. F. Barkley

[There 1 s [\ general conce:!?t in the coal trade tha t the ;noi sture-and ash-free B. t.&apos;I. of coal from t.he oome seam, and surely from the same mine, is substantially a cor.stant: that calculatio!: of the ::1oisture-and ash-free B. t. u. value f~~oJl t he proxima te ru:al~rsi sand. 3. t. u. determined in tl19 laboratory 111ill reveal v:?letller a coal came f~&apos;om a. given : area or seam; and that, having this constant, the 3.t.u. value of a coal sample can be c lculatcd fairl...&apos; closely 11:0on a? dry or as~received basis from the r.lois]

Jan 1, 1941

By T. A. Hendrickson

The Bohemia district, situated about 30 miles southeast of Cottage Grove, Oreg., in the Calapooia Range, has been the major producer of lead and zinc in Oregon. Sporadic production has been Maintained from the district since its early discovery about 1858. In 1942, a selective-flotation mill was built at the Champien mine, which operated for only a short time and was forced to close because of the war and lack of labor. The Champion mill reportedly has been operated as a custom mill for the treatment of ore from the Musick and Helena mines, located in the district sometime in the past. This report summarizes the results of laboratory ore-dressing studies made on ore samples from the Musick and Helena Mines.

Jan 1, 1951

By John J. Sammarco

This report (System Safety Guidance 5.1) is the sixth in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various lifecycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [< 5.1 System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 8, 2005

By M. D. Carver

This investigation was undertaken by the Bureau of Nines to determine the effects of impurity levels on the mechanical properties of columbium at low temperatures. High-purity, electron-bombardment-melted columbium was purchased and used as a basis material. Variations in impurity levels were obtained by arc-melting charges containing definite amounts of added impurities. Tensile tests were conducted at low temperatures. Results showed the almost pure basis metal to be ductile at minus 194° C., the lower limit of the range used, Ductility of less pure columbium appeared to depend on interstitial element content. The ductile-to-brittle transition temperature appeared to be raised by increasing carbon content in the range of 50 to 730 parts per million, nitrogen content in the range of 50 to 200 parts per million, or total interstitial element content in the range of 240 to 1,380 parts per million. Some evidence was obtained indicating that decreasing cold work also raised the transition temperature, but recrystallization appeared to have no effect on it. Variations in interstitial element levels appeared to have little or no effect on ultimate strength of columbim in the range of room temperature to minus 194° C, Physical metallurgy studies of massive arc-melted and electron-bombardment- melted columbium were included in the columbium-tantalum research work assigned to the Albany Metallurgy Research Center in fiscal year 1959.

Jan 1, 1961

By J. D. Marchant

In the spring of 1953 a series of heats were made using a 3-phase, size ST, Pittsburgh Lectromelt arc furnace to develop a method suitable for melting, refining, and granulating cobalt powder produced by the Calera Mining Co., at Garfield, Utah. According to specifications stipulated by General Service Administration, the granules had to pass a 2-inch screen and be retained on a 6-mesh screen, be low in phosphorus and sulfur, and contain a minimum of 98.7 percent cobalt plus nickel. Various combinations of water temperature, water jets, and rate of pouring were tried early in the campaign to produce desirable granules. It soon became evident that a properly refined and deoxidized molten bath was the major requirement for a satisfactory product. The physical characteristics of the granules were improved also if, just before pouring, the surface of the molten metal bath was pre-pared by a method involving the use of silica flux. The Bureau processed 107,750 pounds of cobalt powder. A total of 104,810 pounds of cobalt granules meeting General Service Administration specifications was returned to the producer. The refining slag, which was also returned to the company, contained 1,781 pounds of metal.

Jan 1, 1955

By Constantine C. Popoff

Several limestone deposits in western Washington were examined by the Bureau of Mines in 1946. This report presents data obtained from the investigation of limestone deposits in the vicinity of Arlington, Snohomish County, Wash. The work consisted of surface surveys and sampling. Samples were taken where complete, or nearly complete, sections of limestone were exposed or where individual beds were exposed at a number of separate .localities. Areas were cleaned by blasting prior to sampling. Channel samples were cut where practical; otherwise chip samples taken. Twenty-one samples were taken. The locations of the samples and the analyses are shown on maps accompanying this report.

Jan 1, 1949

By Carl R. Peterson

Development of reliable, portable, low headroom, hard rock crushers would improve the efficiency of most currently operated conveyor systems and make it possible to bring conveyor haulage closer to the face, thus eliminating expensive rock rehandling procedures. A crusher that could be easily moved would permit the more widespread use of lower cost haulage systems, such as conveyors, to transport the ore out of the mine. Such crushers would be installed close to the working areas, resulting in an optium haul from the face to the dump location. A recent contract study by Rapidex, Inc., "Application Study of Portable Underground Hard Pock Crusher" (USBM Contract No. J0265006) provides a survey of industry needs in portable underground crushing, together with conclusions and concepts as to specifications and type of crusher required to serve the greatest number of operations. To fill this need a three phase program has been undertaken by the Bureau of Mines: Phase I - Design: Phase II - Construction and Testing, and Phase III - Production Underground Test. This report covers Phase I only, and includes the complete engineering design and specifications of the Rapidex Rotary Jaw Crusher conceived in the earlier "Applications Study". Also included are the design, construction, and testing of a quarter-scale functional model, utilizing three different types of rock and two different crusher feeder systems.

Jan 1, 1978

By Bertha R. Klahold

"In response to numerous inquiries regarding tests and analyses of minerals and related inorganic materials; Bureau of Mines Information Circular 6999, ""Laboratories That Make Fire Assays, Analyses, and Tests on Ores, Minerals, Metals and Other Inorganic Substances,"" by C. W. Davis and M. W. von Bernewitz, was published .in 1938 and revised in 1939 (I. C. 6999R). In this paper on analytical and testing laboratories, the original text has been rewritten and expanded, and a table has been added, in which are listed laboratories prepared to offer a number of special testing services in addition to ordinary assays and chemical analyses. The arrangement of laboratories on, a geographical basis has been maintained.This circular is compiled as a public service, and none of the laboratories listed herein is recommended over any other,These lists were compiled from questionnaires sent to organizations whose work is connected with mineral and metallurgical testing. The response in general was very satisfactory, and the author takes this opportunity to express her appreciation to the officers of the listed laboratories for their cooperation.Acknowledgment is also made of the valuable assistance of the members of the technical staff particularly Morris Slaving/ of the Eastern Experiment Station of the Bureau of Mines at College Park, Md., in the preparation of the questionnaire and technical descriptions.Many mineral samples are sent to government agencies in the National Capital with the request that they be assayed or chemically analyzed. It should be emphasized that there is no place in Washington D. C. where assays and quantitative analyses are made for the public b the Federal Government.Virtually all of the States maintain a bureau of mines, a geological survey, or some similar organization, frequently at the State University, where minerals found by residents of the State will be identified free of charge. Usually, a charge is made for assays. Specific tests, as on clays, are made by some of these offices.The Federal Bureau of Mines, although it attempts to avoid duplication of services rendered by State Bureaus, is always glad to give advice as to prospective markets. It does not compete with private assayers and chemists, but with respect to samples sent to its field laboratories, it does offer to identify them as far as this can be done by inspection and simple optical and chemical tests. This examination is usually sufficient to indicate whether the material has commercial value, or at least if the expense of an assay would be warranted. Except in connection with its own technical investigations, no assays or other special tests are made by the Bureau of Mines.The Federal Geological Survey and the National Museum also make simple tests of specimens as a public service. Neither of these bureaus nor the Bureau of Mines, however, can afford to render such services on long suites of specimens submitted by mineral dealers, well drillers, or others, when such work can be done regularly by commercial concerns."

Oct 1, 1949

By W. H. Kerns

The Critchfield manganese deposit, Huntingdon County, Pa., was investigated by the Bureau of Mines in October 1942. Iron ore was mined from an open cut just southeast of the manganese deposit about 80 years ago. The Critchfield Sand & Feldspar Co. was operating (1942) a clay-mining and beneficiation plant northeast of the manganese deposit. The Bureau completed six rotary bucket-drill holes and three hand-auger holes, aggregating 370 feet on the deposit. This report describes the work performed and presents the results obtained.

Jan 1, 1948

By A. L. Engel

The Bagdad-Chase copper-gold mine south of Ludlow, Calif., was visited by an engineer of the Bureau of Mines in July 1955 to determine the mine&apos;s status of activity and to obtain a bulk sample for metallurgical testing. The deposit was discovered in 1903 and has been worked intermittently. It has a production record of about 273,000 tons of ore. The first production of about 150,000 tons was treated in a cyanide plant 2 miles west of Barstow, Calif. The extraction of gold was not satisfactory because of the presence of copper minerals. Since 1910 the ore has been shipped to various smelters in Arizona and California for use as a flux.

Jan 1, 1957