Search Documents

By Peter D. Lohn

The Bureau of Mines conducted both laboratory and field investigations to study the effectiveness of medium-pressure (up to 30,000 psi) water jets in controlling the generation of airborne respirable dust during the hydraulic fragmentation of coal. Laboratory studies were conducted at the Farmington High Energy Test Site of the Twin Cities Mining Research Center, and field studies were carried out at the Humphrey No. 7 mine, Mount Morris, Pa., in the Pittsburgh coalbed. The water jets were produced by commercially available triplex pumps. The dust samples were collected by midget impinger samplers, and analyzed by electronic and optical counting techniques. Respirable dust concentration for a full-scale production model was projected at below 2 mg/m3, the maximum exposure allowed by the Federal Coal Mine Health and Safety Act of 1969.

Jan 1, 1975

By R. G. Meara, O&apos

The land-pebble district of Florida, which in 1928 supplied 96.7 per cent of the phosphate production of that State and 82 per cent of the domestic requirements of the United States, is centered in Polk and Hillsboro Counties about 30 miles east of Tampa The deposits are unconsolidated sediments occurring as beds of phosphate matrix overlain by a mantle of barren sands and clays. The matrix consists of a mixture of Sand (quartz grains), clay, and phosphate rock in which the coarsest sand is much finer than the coarsest phosphate; that is, the sand is segregated in the fine material. Before the introduction of classifiers the concentration consisted of log washing, and screening at about 20-mesh, which was usually the finest size that could be taken to maintain commercial grade, 66 per cent B. P. L. (bone phosphate of limey or more. When classifiers were introduced some of the fines that had escaped at the head of the washery and some of the minus 20-mesh material isolated during the rushing and formerly lost supplied the feed.

Jan 1, 1931

By W. W. Adams

Three hundred and twenty-eight mines and quarries, representing 36 States, took part in the twelfth yearly accident-prevention contest conducted by the United States Bureau of Mines and known as the National Safety Competition. Four underground mines and one open-cut mine (which represents the quarry and open-cut mine group), each the leader in its group, were awarded the ?Sentinels of Safety? trophy. Relative standing in the contest" was determined by the number of days lost from accidents in proportion to the total number of man-hours worked. Since 1925, when the National Safety Competition was inaugurated, an increasing interest has been taken in it by mining and quarrying companies as a means of stimulating mine and quarry safety by competition among similar plants. Each participating plant can, on a basis of its standing and record in the contest, determine to what extent its safety program is succeeding or to what extent it needs strengthening. With this information, each company that has a low standing in the contest can intensify its safety-promotion efforts the following year to obtain a lower rate and possibly win the trophy or achieve honorable mention in the competition. Except for 1929, the National Safety Competition of 1936 represented more man-hours of employment than any other year since the yearly contests began.

Jan 1, 1937

By W. W. Adams

Three hundred and twenty-eight mines and quarries, representing 36 States, took part in the twelfth yearly accident-prevention contest conducted by the United States Bureau of Mines and known as the National Safety Competition. Four underground mines and one open-cut mine (which represents the quarry and open-cut mine group), each the leader in its group, were awarded the ?Sentinels of Safety? trophy. Relative standing in the contest" was determined by the number of days lost from accidents in proportion to the total number of man-hours worked. Since 1925, when the National Safety Competition was inaugurated, an increasing interest has been taken in it by mining and quarrying companies as a means of stimulating mine and quarry safety by competition among similar plants. Each participating plant can, on a basis of its standing and record in the contest, determine to what extent its safety program is succeeding or to what extent it needs strengthening. With this information, each company that has a low standing in the contest can intensify its safety-promotion efforts the following year to obtain a? lower rate and possibly win the trophy or achieve honorable mention in the competition. Except for 1929, the National Safety Competition of 1936 represented more man-hours of employment than any other year since the yearly contests began.

Jan 1, 1937

By William C. Henkes

Anticipating the availability of space-altitude imagery from the Earth Resource Technology Satellites (ERTS), the Bureau of Mines investigated the possibilities of using suck imagery in its activities in solid waste disposal, reclamation of mine workings, and mineral resource inventory. The study indicates that monitoring open pit and strip-mining operations can be done using conventional techniques if the sharpness of the imagery is sufficiently high. Possibilities also exist for semi-automated processes for change detection. Additional experimentation is needed for multispectral discrimination and identification of mine-related phenomena.

Jan 1, 1971

By A. L. Peyton

Manganese-oxide minerals occur in irregular pockets distributed through the residual clays of the Cartersville district, which lies 45 miles north-west of Atlanta in Bartow County, Ga. The district produces, or has produced, limonite, barite, specular hematite, ochre, ferruginous manganese, manganiferous iron are, as well as manganese. Bureau of Mines engineers have visited the district on three occasions - in December 1939, February 1941, and October 1942. During the visit of February 1941, 80 tons of samples of manganese-bearing clays were taken from seven properties for ore-dressing tests, which were conducted at the Bureau of Mines laboratory at Rolla, Mo. The. October 1942 visit was for the purpose of reappraising the district in the light of knowledge gained from the ore-dressing studies and to prepare a plan for the district's development. Exploratory drilling was begun in March l943 and was continued until June 1945. Nine properties were explored that, roughly follow a line beginning near Cartersville and extend to a point 2 miles northeast of the village of White. The work consisted of bulldozer trenching, rotary bucket churn drilling, sampling, and analytical determinations. The manganese district is 18 miles long with a maximum width of 7 miles at Cartersville, which lies at the center of the district. The work of the Bureau was confined to the northern half of the district between Cartersville and Pine Log. The properties explored comprise but a small portion of the Potential producing area.

Jan 1, 1949

By Lloyd Williams

1. This investigation shows that the Poplar Creek is the most important bed in Scott County from a production standpoint. Although the Poplar Creek bed contains the largest reserve, the Big Mary has a larger recoverable reserve. Estimates of reserves also have been made for the Pewee, Red Ash, Windrock, Upper Pioneer, Jellico, and White Oak beds. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 143 million tons as of January 1, 1954. Of this total, 74 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By B. W. Gandrud

This is the first report published by the Bureau of Mines on washability characteristics of coal from beds in Tennessee. It is based principally upon screen-sizing and float-and-sink tests of raw coal from a bed on the Cumberland Plateau. Stripping operations were undertaken recently on this bed by the Cumberland Collieries, Inc., near Chalybeate,Van Buren County, Tenn. The bed has not been definitely correlated, but it may be an extension of the Sewanee bed, which has been mined extensively in the Tracy City district to the south-vest and at points near Dunlap and Pikeville to the southeast and east. It was spoken of by officials of the Cumberland Collieries as the Sewanee bed at the time of sampling for this study. In a letter dated October 16, 1948, W. D. Hardeman, geologist of the Department of Conservation, Nashville, Tenn., states: "The stripping operations of the Cumberland Collieries near the old postoffice at Chalybeate are, I am fairly certain, in the upper part of the Whitwell shale, which carries the Sewanee coal. This coal may be a stray seam, but it probably can be correlated with the Sewanee coal, which is mined farther east. "There are no detailed geologic maps or reports covering the area, and this opinion is based on what was observed in visiting the strip mines in that general vicinity." The laboratory work upon which this report is based was done at the Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the Cumberland Collieries, Inc.

Jan 1, 1949

By H. B. Brunot

A complete list of permissible mine equipment , tested and approved by the Bureau of Mines previous to January 1 , 1947 , was published as Information Circular 7432.27 A list of permissible mine equipment tested and approved by the Bureau of Mines during the calendar year 1947 was published as Information Circular 7465.3/ The present list supplements Information Circular 7432 and includes all of the equipment approved during the calendar years 1947 , 1948 , and 1949. It therefore supersedes Information Circular 7465. The list also includes an appendix ( No. 2 ) giving the symbol that must be used by every cable manufacturer in marking trailing cables that have passed the test for flame resistance as stated in the amendment of October 21 , 1947 , to Schedule 2E . The items are numbered to indicate the consecutive order in which each type of machine or device was approved in its particular classification . Thus , Information Circular 7432 showed six air compressors on the active list ; five additional compressors , Nos . 7 to 11 , inclusive , in this category were approved during 1947 , 1948 , and 1949 . Several items that were listed in Information Circular 7432 have been repeated in this circular where it was necessary to show that approvals of such equipment were extended to cover an additional voltage rating or other changes . Equipment listed in these circulars is approved by the Bureau of Mines only when found , upon inspection and test , to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal -mining industry . The use of such equipment in mines known to be gassy , as well as in those that may become so , is earnestly recommended in the interest of safety . This circular is published so that the industry may be kept informed as to the many types of machines , devices , and lamps that are available for reducing explosion and other hazards incident to coal mining . This circular and Information Circular 7432 give the complete list of permissible mine equipment that is available under the various classifications .

May 1, 1950

By T. E. Gray, A. W. Deurbrouck

This report describes the preparation characteristics of significant coalbeds in Kanawha County , W. Va . It is one in a series of Federal Bureau of Mines reports planned to determine coals suitable for producing metallurgical coke , either as mined or after beneficiation . Almost 9.4 million tons of coal was produced in Kanawha County , W. Va . , in 1959 , of which about 67 percent was cleaned mechanically in 10 cleaning plants . It has been estimated that more than 5,505 million tons remain in the county . Samples were collected from Pittsburgh , Stockton - Lewiston , Winifrede , Cedar Grove , Peerless , Upper Kittanning , Coalburg , Powellton , Eagle A , No. 2 Gas , and the Lower Kittanning beds . These beds were selected by the Bureau based on current production rates and estimated minable reserves . Float - and - sink tests of the samples collected from Eagle A , Peerless , Cedar Grove , Winifrede , and No. 2 Gas beds show that these coals at one location each are suitable for metallurgical use without washing . Lower Kittanning bed at four locations ; Pittsburgh , Stockton - Lewiston , and No. 2 Gas beds at two locations each ; and Coalburg , Powellton , Winifrede , Peerless , Upper Kittanning , and Cedar Grove beds at one location each can be upgraded to metallurgical quality by mechanical cleaning . Crushing the samples to 3/ 8- inch top size increased yields substantially at 1.30 specific gravity of Pittsburgh ( 17.5 percentage points ) and Upper Kittanning ( 13.0 percentage points ) beds and increased yield for the other beds sampled to a lesser amount . At this specific gravity , finer crushing caused In the 1.58 specific gravity float a general decrease in ash and sulfur . fractions of the other samples tested , most of the yields , and ash and sulfur contents , were lowered slightly by finer crushing .

Jan 1, 1963

By G. L. Oldright

This paper is the twelfth of a series on smelting in the lead blast furnace and the fifth dealing with blast-furnace gases. It was noted in Report of Investigations 2957 that the gases evolved from the top of the lead blast furnace at Tooele were similar in composition to those from the top of an iron blast furnace. It was noted in Report of Investigations 3095 that at Kellogg, where a smaller percentage of coke on charge and shorter stock column were employed, the gases evolved were much less reducing. At times there was a considerable amount of oxygen in the top gases at the second plant. More SO2 was also evolved from sulphides in the charge. Then operations were conducted as at Kellogg, the gases were alternately reducing and oxidizing. This paper deals with the gases evolved in smelting a charge containing more zinc than at either of the other two plants with about the same amount of coke as was used at Kellogg,: To compare other factors influencing the composition of the gases, it may be noted that at Tooele the approximate height of the charge column was 15 feet, at Kellogg 9 feet and at Trail 13 feet. The furnaces have about the -same cross-sectional area- tog. The furnaces at Tooele are about 6 inches wider at the tuyeres, being 54 inches wide against 48 for the other two plants. At Tooele and Kellogg the furnaces are fed at the top from bottom-dump cars. At Trail the charges are dumped from Decauville cars (bottom cars which dump when tilted), which run on tracks placed on both sides of the blast furnaces. The hoods through which the waste gases are conducted are directly above the shafts of the furnaces. The flues for removing the effluent gases lead off from under the charge floor at Tooele and Kellogg. (Charging and distribution of the feed in the furnace covered later in a rate paper of series.)

Jan 1, 1934

By A. W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds from which samples could be obtained in Webster County, W. Va. In 1964, approximately 825,000 tons of coal was produced in the county, of which 732,000 tons was mechanically cleaned in three preparation plants. The Sewell coal bed accounted for 94 percent of the coal produced. Twelve samples were collected from five coalbeds. Four of the samples would require upgrading to meet metallurgical requirements; two others of just over 8.0 percent ash would require some upgrading. In general the coalbed samples collected in the county were of medium-sulfur and medium-to low-ash content as received or after removal of the sink 1.58-specific-gravity material.

Jan 1, 1966

By W. H. Kerns

The Taylor Creek lead-zinc deposit is on Taylor Creek, approximately 1-1/2 miles from tidewater, at the head of Duncan Canal, on the east side of Kupreanof Island, Petersburg district, southeastern Alaska. The property was located in 1903, and a 30-foot discovery cut was put to the west tank of the creek. Very little prospecting end developing has been done since that time. The property was examined by J. C. Roehm, associate mining engineer, Territorial Department of Mines, Juneau, Alaska, in June 1946. From exposure n the creek, a mineralized zone with possible dimensions of 1,700 feet by 1,000 feet was indicated. The general strike was northwest, and the dip was low and variable to the northwest. During September through November 1948, the Bureau of Mines conducted a project on the property. Four diamond-drill holes, totaling 770.5 linear feet, were drilled from the surface and 280 lineal feet of hand trenching done. The mineral deposit was found to occur as patches that appear to be a replacement in dolomitic limestone. The patches of mineralization are small, irregularly shaped, and irregularly distributed. Maps showing the location of the drill holes and trenches, analyses of the cores from the drill holes, and anal lee of the samples from the trenches accompany this report (see, also, appendixes A, B, and C).

Jan 1, 1950

By R. K. Franklin, S. T. Reese, J. J. Forbes

"INTRODUCTION It is a recognized fact that in the coal-mining industry coal dust must be allayed to promote the safety and health of underground workers. The Bureau of Mines has been cognizant of the hazards of coal dust for many years, and the necessity of controlling such dust was acknowledged when the Federal Mine Safety Code was formulated. Accumulations of coal dust increase the explosion hazard in a bituminous-coal mine and facilitate the propagation of an explosion. Some of the coal dust produced in mining is inhaled by the workers and contributes to respiratory infection. Impairment of vision and personal discomfort resulting from working in dense clouds of coal dust reflect unfavorably on the efficiency of workmen. Considerable coal dust, originating at the working face, is carried in the ventilating current and deposited elsewhere in the mine, thereby increasing the explosion hazard. It is apparent, therefore, that if coal dust could be allayed effectively at its points of origin, the dust-explosion hazard in bituminous-coal mines would be reduced greatly.Although dust control is practiced in many bituminous-coal and lignite mines, the extent and effectiveness of control for the, entire industry-is not generally known. The purpose of this circular is to present such information clearly, and to encourage coal-mine operators to install dust- allaying equipment.Factual data on dust-allaying practices at working faces in a large number of the bituminous-coal and lignite mines in the United States were .compiled from reports on recent Federal inspections of these mines, The information is presented in tabular form to permit review of the dust-allaying practices of a substantial part of the industry, by States, and also according to employment, and loading practice."

May 1, 1950

By C. H. Bloomster

This study estimated (1) radon and radon daughter emissions from underground uranium mines; (2) the reduction in radon that would be released to the surface by using control techniques such as bulkheads, sealants, backfilling, and positive pressure ventilation; (3) the cost for radon and radon daughter removal from total exhaust air; and (4) total radon and radon daughter discharge for lower occupational exposure limits. For 13 large underground uranium mines, estimated yearly radon emissions from each mine ranged from 900 to 3,400 Ci. The estimated age of air emitted from the mines ranged from 11 to 37 min. Potential radon removal methods for the total mine exhaust were evaluated. The cost of these methods was prohibitive. Diurnal and seasonal changes may affect radon emission over short periods of time, but do not affect the total emissions over the long run. Radon and radon daughter emissions would be little changed by increased ventilation requirements needed to achieve lower occupational exposure limits. The concentrations in the exhaust would be lower, but the total release would be the same

Jan 1, 1984

By G. W. Elger

The Bureau of Mines conducted laboratory and larger scale studies on samples of domestic perovskite and ilmenite ore concentrates to devise a procedure for recovering TiC from these ores. From the concentrates, mixtures of titanium and calcium carbides were produced. The carbides were then ground and reacted with water. This reaction decomposed the CaC2 to acetylene and hydrated lime and simultaneously liberated the TiC. Using a combination of elutriation and gravity-separation techniques to separate the hydrated lime, approximately 93 pct of the titanium was subsequently recovered as purified carbide containing 54 to 70 pct titanium with CaO content as low as 0,6 pct. This combination of techniques can be used to separate more than 90 pct of the CaO from the TiC. Therefore, this carbiding procedure is a viable method for treating titaniferous materials, including perovskite, that contain more than 20 pct CaO. Tests made in a static-bed reactor showed that for the reaction of TiC with elemental chlorine to produce titanium tetrachloride (TiCI4), a temperature of at least 940° F is desirable to achieve a suitable extraction of titanium in a laboratory chlorination reactor. In fluidized-bed tests at 840° F, 98 pct of the titanium contained in TiC was extracted.

Jan 1, 1980

By Wesley T. Holmes II, Lloyd H. Banning

Electric - smelting studies were made on titaniferous materials obtained from the Klukwan and Snettisham , Alaska ; Choteau , Mont .; and Iron Mountain , Wyo . , deposits with the objective of determining the feasibility of producing pig iron and an enriched titania slag in one test series and pig iron alone in another test series . In addition , related studies were conducted to determine the amenability of Choteau crude ore to wet -magnetic separation and to determine the quality of steel that could be produced from the titaniferous pig iron . The continuous smelting tests were made in a three - phase , submerged - arc , electric furnace , and the laboratory steelmaking tests were made in a singlephase electric - arc furnace . A continuous , belt - type , wet - magnetic separator was used in conjunction with a ball mill and a spiral classifier in recovering titaniferous magnetite from the crude Choteau ore . Pig irons containing less than 0.05 percent phosphorus or sulfur were readily produced from the titaniferous materials ; iron recoveries ranged from 92 to 98 percent . The Choteau ore was ground to minus 65 - mesh to produce a concentrate containing 60 percent or more iron . The steel produced from the titaniferous pig iron was a high - quality product .

Jan 1, 1964

"MASSACHUSE'M'S INSTITUTE OF TECHNOLOGYBOLSAITIS, PETERMassachusetts Institute of TechnologyDepartment of Mineral Engineering77 Massachusetts AvenueCambr1dge,MA 02130(614) 253-5069ELLIOIT, JOHN F.Massachusetts Institute of TechnologyDepartment of Mineral Engineering77 Massachusetts AvenueCambridge, MA 02130(617) 253-3305RING, TERRYDepartment of Materials Science and EngineeringMassachu5etts Institute of TechnologyCambridge, MA 02130(6117) 253-4299"

Jan 1, 1988

By R. H. Sprute

The Bureau of Mines conducted a feasibility study and designed an operational system for consolidating waste coal sludge in a 110-acre pond by applying direct current between buried and floating electrodes. Consolidation would reduce the sludge to half its present volume, there-by extending the working life of the pond as well as creating a safe, stable impoundment. The project was conducted by the Bureau under an agreement with the Washington Irrigation and Development Co. (WIDCO), located near Centralia, WA. Part 1 of this report, published as Report of Investigation 8666 in 1982, covers the results of laboratory tests at the Bureau's Spokane Research Center and of a small-scale field test at WIDeO's coal preparation plant. Test results show the process is efficient and cost-effective when power is applied at low current density. Part 2 (this paper) describes a detailed design for an electrokinetic system to dewater WIDCO's 110-acre pond with a 27.4-acre electrode array. Densification of the inactive sludge pond will require 3.6 yr of treatment for a total cost of $1,450,000. The study and design are site specific, but design procedures and analyses are sufficiently detailed to serve as a guide for applying the process to any sludge pond.

Jan 1, 1988

By J. B. Zadra

Much has been published by various investigators on the use of activated carbon for adsorbing precious metals from cyanide solution and pulp. For the benefit of the reader, a list of these earlier publications appears at the end of this report. The present paper deals only with a process for extracting gold from gold-laden carbon and re-use of the de-adsorbed carbon. At the Getchell mine, Redhouse, Nev., experiments have been in progress for several years concerning the use of activated carbon to adsorb gold from their slime circuit pulp. The experimental work has been successful. Their practice has been to ship the gold-laden carbon to a smelter for treatment, which meant the total loss of the carbon in addition to smelter and freight, charges, all of which proved costly and wasteful.

Jan 1, 1950