Search Documents

By Donelson A. Robertson

Literature was searched and cases of alleged water well damage were investigated. Occurrence of ground water in Appalachia is primarily in low yield, fractured, water table aquifers. Four test sites were chosen based on geographic and geologic diversity. Test wells were drilled at each site and base line data on water quality, static water level, and drawdown characteristics were obtained before surface mining commenced. Blast induced ground vibrations were measured at the surface by the wells at levels up to 5.44 inches per second maximum resultant particle velocity. Measurements made at the bottom wells indicated that vibrations were considerably attenuated at depths of 140 to 160 feet. No direct evidence of change in water quality or well performance was produced by blast vibrations, but removal of downslope support by excavation does cause lateral stress relief which permits the water-bearing fractures to become more open. This additional storage capacity causes the static water level to drop and for well-bore permeability to improve. Static water level recovers if sufficient recharge is available and well performance is improved.

Jan 1, 1980

By Donald E. Redmon

This Bureau of Mines report examines the injury experience in the quarrying industry for the years 1968-69. Twenty-eight tables for each year are presented in which disabling work injuries are summarized by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By R. F. Kendall

Only a limited number of mass and infrared reference spectra of high purity unsaturated hydrocarbons and oxygenates are presently available in the literature. To aid Bureau of Mines research programs requiring such references, 64 mass spectra and 70 infrared spectra were obtained and are reported. The individual compounds, acquired from commercial sources, were purified by preparatory gas chromatography. Purity determinations were made using a combination of analytical gas chromatography, microhydrogenation, and catalytic deoxygenation. These spectra will aid spectroscopists in the identification of compounds of the types reported.

Jan 1, 1966

By P. A. Cox

Guidelines are provided for the design of explosion-proof electrical enclosures that will meet MSHA certification requirements according to Part 18, Title 30, of the Code of Federal Regulations, and fulfill their intended service underground. The guide covers only those aspects of design which affect enclosure strength, ruggedness, endurance and flame path, i. e., the enclosure ability to properly contain an internal explosion. Internal static and explosion pressures, external impact and thermal heating load are treated as well as the proper selection of materials and welding procedures.

Jan 1, 1985

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The tactual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the twelfth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate halt-township map. The description of each half township is followed by a description of each deposit developed in that halt township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By W. D. Dietzman

This Bureau of Mines report presents a profitability analysis of producing crude oil by waterflooding. Included are the estimated costs of installation of water injection and producing equipment for waterfloods at 2,000 and 4,000 feet and the estimated annual operational expenses for each in west Texas. Using these cost estimates as a base for selecting a range of costs that are indicative of producing crude oil by waterflooding, a simulation technique was derived for determining the profitability under various conditions. Because of the large number of combinations of variables used in this study, a high-speed digital computer was utilized for the calculations. The variables include operational expenses, capitalized costs, price of the oil, annual production, and leasehold acquisition cost. The results obtained from the simulations are presented Fn the appendix. In addition, a nomographical approach was chosen for presentation of the profitability. Five nomographs are presented that can be used for fast estimation of the discounted cash flow (DCF) rate of return that might be expected from a prospective or active operation under various sets of assumed conditions.

Jan 1, 1974

By Joseph A. DeCarlo, Eugene T. Sheri dan

The process of converting coal into coke is known as carbonization. Essentially, carbonization is destructive distillation in which the volatile matter of coal is released when coal is heated above its decomposition temperature and passes through a plastic stage before solidifying and forming coke. The mechanics of coke formation are complex, and the specific properties of certain coals that allow them to "cake" or form coke are still unknown. Coke is a hard, cellular, carbonaceous mass, formed by heating coal in the absence of air. It is porous, irregular in size and shape, and is similar in appearance to wood charcoal. Coke, however, is denser, more porous, and more abrasive than charcoal. Coke has been in use for several thousand years. History has recorded its use in Greece before the birth of Christ, and it is thought to have been used in China even before that time. It was not until the l6th century, however, that a method for coking was developed in Europe that subsequent ly evolved into the coking process that is known today. The coke industry in the United States began in the latter half of the 19th century when beehive-coke ovens were built to supply fuel for iron blast furnaces. Before this time, an iron industry fueled principally by charcoal had been in existence for several hundred years. With the depletion of timber resources, coke gradually replaced charcoal as blast-furnace fuel, and by 1875 more iron was made with coke than with any other fuel. Before 1893 a 11 coking was done in beehive ovens. These ovens are refractory kilns with arched roofs, sometimes joined together to form batteries.

Jul 1, 1964

By Fun-Den Wang

This report presents the results of two large scale field coal pillar strength tests (80 ft by 80 ft), the results of a series of laboratory small core sample tests, and the correlation between those field and laboratory tests. The concept of applying laboratory coal sample strength data to predict the in situ coal pillar strength appears to be feasible. The deformation property of large pillars can be obtained successfully by testing the coal sample in the laboratory within acceptable accuracy. There are prevailing directional strength and deformation properties in coal pillars along the butt and face cleat system.

Jan 1, 1976

By Donald W. Scott

Chemical thermodynamic properties for the ideal gas state from 0 to 1500 K are tabulated for all of the alkane hydrocarbons through C10. These properties are based on correlations of the extant data for the entropy, vapor heat capacity, and enthalpy of formation of individual alkanes and the equilibrium constants of alkane isomerization reactions.

Jan 1, 1974

By Richard D. Miller, Geraldine P. Norrell

This publication contains routine analyses and related source data for 295 natural gas samples from 18 States collected during calendar year 1963 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Five previous publications have been made to present the results of 5,998 gas analyses made by the Bureau of Mines Helium Activity , prior to 1963. The first three , Bulletin 486,5 Bulletin 576,6 and Bulletin 617,7/ contain analyses and source data on 5,214 gas samples collected from 1917 to January 1 , 1961. The fourth and fifth publications , which are published as Information Circulars , supplement the three Bulletins and contain 784 analyses of samples collected during 1961 and 1962. The present Information Circular is the third annual publication supplementing the three Bulletins .

Jan 1, 1965

By John A. Kost

Control of the dust produced by continuous mining machines in coal mines is conventionally attained by water sprays from fixed nozzles mounted on the frame of the machine behind the cutting head. In the tests conducted under this contract a so-called "wet-head" machine was used, where the spray nozzles were mounted on the rotating head itself, close to the coal-cutting bits. The tests were conducted at the Robena Mine of U.S. Steel Corporation, using Lee-Norse machines. Operating the wet-head machine and a conventional spray machine in turns in the same section, it was found that the wet-head produced approximately 25 percent less respirable dust and 60 percent less total airborne dust than the conventional spray machine. The wet-head also greatly improved the visibility of the cutting bits from the machine operator's position. Several difficulties had to be overcome before any meaningful tests could be conducted, including excessive pressure drops in the piping system and plugging of the nozzles from internal water contamination. The major obstacle, however, was the rotating water seals on the wet-head, which leaked excessively after only a few hours of operation. Only after several changes and plant and laboratory tests was a design found which permitted conducting the underground tests without appreciable water leakage.

Jan 1, 1976

By R. D. Leitch

"The pollution of streams has received much attention during the last few years, and although there are many other and more serious forms of pollution, the problem of acid mine drainage is important in certain sections of the country, particularly in Pennsylvania. At the request of the United States Public Health Service the Bureau of Mines undertook to determine some of the factors contributing to formation of acid mine waters, the yearly variations in quantity and quality of drainage, effect of mining methods, and various other questions arising in connection with the problem; some attention was also given to its economic phases.In acknowledgment, the writer wishes to thank Dr. R. R. Sayers, Chief surgeon; A. C. Fieldner, chief chemist; and W. P. Yant, supervising chemist, health laboratory section of the Pittsburgh Experiment Station, all of the Bureau of Mines, under whose direction the work was conducted.Because no data of a like nature had previously been determined, and with the thought that such data would throw additional light on the general subject, a stream having a number of mines draining into it was selected for observation in both high-sulphur and low-sulphur bituminous-coal districts, as designated in commercial rating. These mines and streams were visited in both wet and dry seasons to note the quantity and variations in acidity of mine drainage and the subsequent effect on streams. Maps of these streams with the sampling points are shown in Figures 1 and 2. In a report of this nature a great deal of tabular data is best emitted, but reference to the maps will serve to indicate the factors that determined sampling points, such as tributary streams and gobs."

Sep 1, 1928

By Michael Sokaski, M. R. Geer, H. F. Yancey

This report is one of a series describing investigations by the Federal Bureau of Mines of the performance of various types of coal - cleaning equipment ; other reports in the series are listed in the bibliography . The information in these reports is useful to the coal industry and the manufacturers of coal - cleaning equipment in several ways : First , it assists the coalpreparation engineer who is planning a new plant to select the type of process best suited to the requirements by enabling him to forecast the yield and quality of clean coal obtainable with each type of equipment . Second , the information serves as a yardstick by which the performance of a plant can be judged and thus helps determine whether it is operating at satisfactory efficiency . Both these functions promote better coal - preparation practice ; that is , they help provide coal of more suitable quality for the market and likewise minimize the waste of good coal . This serves the interest of conservation with which the Bureau is vitally concerned . The present report deals with three plants using the Tromp dense - medium process , named after its inventor , K. F. Tromp , who developed the process in the Netherlands in 1936.5/ Selection of this particular dense -medium process for investigation was entirely a matter of convenience , and reports dealing with other dense -medium systems are planned for the future . Two baths are employed in one of the plants investigated . The first of these , handling 6- to 3 - inch coal , exhibited an exceptionally sharp separation between coal and impurity . This was characterized by an error area of 12 and a probable error of 0.023 . In the second bath , treating refuse from the

Jul 1, 1960

By W. J. Wenger

Oil fields in the Powder River Basin of Wyoming have produced 731 million barrels of petroleum through 1959. Production in 1959 was 32 million barrels, the highest production since 1924. The record production was in 1923, when the Basin produced 38 million barrels of oil and the Salt Creek field, then at its peak, produced 35 million barrels. In this report, the characteristics of crude oils found in the Basin are used as a basis for determining the best re-fining uses for the oils and for predicting the characteristics of oils that may be discovered in the Basin in the future. Analyses of 108 oils sampled over a period of 30 years are presented Crude oils of two major types are produced from the Powder River Basin. One has a low sulfur content and occurs in younger formations, and the other has a high sulfur content and occurs in older formations. The oils with low sulfur contents are generally light colored and waxy, and may be either paraffinic or naphthenic. The oils with high sulfur contents are usually dark colored and asphaltic; only their low boiling fractions are paraffinic. Alteration appears to account for the anomalous properties of some oils found at shallow depths. Shapes and slopes of correlation index curves classify the oils into the same two groups as their sulfur contents, with gently sloping curves representing the low-sulfur oils and steep curves representing high-sulfur, asphaltic oils,

Jan 1, 1961

By J. G. Walters

In 1928, the Coal Carbonization Section of the Federal Bureau of Mines, in cooperation with the American Gas Association, began a survey of the carbonizing properties of American coals. A standard test method for evaluating the carbonizing properties of coals that met the following conditions was developed: To yield products similar to those obtained in commercial operations. To produce yields sufficient to permit analyses and tests of quality. To be laboratory size. To be convenient to operate. To permit reproducible control of test conditions and results. This test method has become known as the Bureau of Mines-American Gas Association (BM-AGA) test (53),3/ and more coals of greater variety have been tested in this apparatus than in any other of similar scale.

Jan 1, 1961

By Loren R. Anderson

This is an Appendix of Volume I. It contains the results of the electric cone penetrometer soundings from the first phase of the testing program.

Jan 1, 1982

By G. R. Strimbeck

This is a report on experimental work on development of a gasification process operating at near atmospheric pressures and using finely pulverized coal entrained in oxygen and steam. The gasifier was designed by The Babcock and Wilcox Co. in cooperation with engineers of the Bureau of Mines Morgantown station. The test work discussed in this report covers the first 34 tests made in the pilot plant in which a strongly coking Sewickley-bed coal, ground to either 70 or 90 percent through a 200-mesh screen, was used.

Jan 1, 1954

By A. W. Deurbrouck

The Bureau of Mines reviewed available data on the effect of crushing high-sulfur coals for the liberation of impurities in the light of increasingly stringent air pollution regulations. The survey, which provided information on Appalachian region coals only, indicated that such important coal- beds as the Upper and Lower Freeport and the Upper Kittanning show significant sulfur reductions when crushed to 14-mesh top size. For many other coalbeds amenability to sulfur liberation by crushing was indicated, although too few samples were available to draw firm conclusions,

Jan 1, 1966

By A. W. Deurbrouck

The Bureau of Mines reviewed available data on the effect of crushing high-sulfur coals for the liberation of impurities in the light of increasingly stringent air pollution regulations. The survey, which provided information on Appalachian region coals only, indicated that such important coal-beds as the Upper and Lower Freeport and the Upper Kittanning show significant sulfur reductions when crushed to 14-mesh top size. For many other coalbeds amenability to sulfur liberation by crushing was indicated, although too few samples were available to draw firm conclusions,

Jan 1, 1966

By W. H. Frederic, F. H. Gibson, R. F. Abernethy

This publication contains the quantitative values for phosphorus , chlorine , sodium , and potassium in United States coals . The samples tested were taken from commercial shipments and have been selected to represent the principal coal producing areas of the country . Due to combining the analytical results from two separate surveys , values for the four elements are not available for all samples .

Jan 1, 1965