Search Documents

By Leonard Obert, Wilbur Duvall

"INTRODUCTION 'The investigation reported herein is part of a comprehensive research program being conducted by the Metal Mining Research Section, Mining Division, Bureau of Mines, on pressure problems in underground mines. This program was initiated in 1937 and for the first 3 years was concerned primarily with measurement of the pressure on mine pillars and supports and their strength. 4/ 5/ During this period, investigations were conducted in both the laboratory and the field in the comparatively shallow load and zinc mines of Missouri and Oklahoma. As a result a seismic method of determining the pressure on mine pillars was developed.Before this research program was initiated, Chas. F. Jackson, chief of the Mining Division, suggested that rock under pressure might give rise to noises inaudible to the unaided ear - that is, subaudible noises. As a result of this suggestion, listening tests were made concurrently with the routine pressure measurements to see if any rock noises were present; with one exception, it was found there were no rock noises in any of these shallow mines. At the same time, pressure measurements disclosed that, with one exception, pillars were not under pressure amounting to more than 10 percent of the crushing strength of the rock. The one exception was a pillar in the Big John mine of the Eagle Picher Mining & Smelting Co. in the Tri-State district, which showed some physical evidence of failure, such as small cracks and spalling; it was reported that the pillar had been heard to crack or snap at intervals. Listening tests in this pillar disclosed that subaudible noises of comparatively small intensity were present and occurred at 1- to 2-minute intervals, on the average. Unfortunately, owing to the shortness of this pillar it was impossible to make any pressure measurements."

Jul 1, 1942

By D. J. Parker

On Thursday, March 18, 1937, the country was shocked by news of a terrific explosion at the New London, Tex., school, which caused the death of 280 pupils rind 14 teachers. The explosion occurred at about 3:05 p.m. in the largest of the 11 school buildings on the campus. Figure 1 shows this building, market; "Main high school building?, with respect to other buildings, pipe lines, oil wells, and gas lines on the property.

Jan 1, 1937

By D. J. Parker

On Thursday, March 18, 1937, the country was shocked by news of a terrific explosion at the New London, Tex., school, which caused the death of 280 pupils avid 14 teachers. The explosion occurred at about 3:05 p.m. in the largest of the 11 school buildings on the campus. Fire 1 shows this building, marked "Main high school building", with respect to other buildings, pipe lines, oil wells, and gas lines or the property.

Jan 1, 1937

By C. A. Herbert

Information Circular 6746 reviewed the fatalities in Indiana coal mines. for the fiscal year October 1, 1951 to September 30, 1933. Since then Indiana has changed its fiscal year to the period July 1 to June 30, but as most statistical data on accidents are arranged according to calendar years, the data in this paper are for the last 3 months of 1932 and the calendar year 1933, rather than for the new Indiana fiscal year. Tables 1 and 2 list the fatalities in Indiana coal mines3/ by cause and occupation for the last 3 months of 1932 and for the calendar year 1933. The fatalities for the small wagon mines employing fewer than 10 men are separated from those employing 10 or more men to call attention to the ex- tremely high fatality rate in small mines, largely because the State mining law does not apply to them nor do they come under the jurisdiction of the Indiana mine inspectors; as a result health and safety conditions are ex- tremely bad. During the last 3 months of 1932, 5 (approximately 42 percent of the total) fatalities occurred in the small mines, while for the calendar year 1933, 12 (approximately 32 percent) of the fatalities occurred in them. The Indiana Division of Mines and Kining estimates that these small mines have an annual production of approximately 325,000 tons, or about 4.5 percent of the total coal-mine production of the State. In other words, for these small mines the fatality rate per tons mined during 1933 was about 10 times as great as for the mines employing 10 or more men. Another lamentable feature in connection with the fatalities in small mines is that very few carry any compensation insurance and the owners are not worth enough financially for dependents of victims to collect anything under the common law; as a result, the dependents of those killed usually are left penniless and subjects of public charity.

Feb 1, 1935

By B. C. Parks

This is the first of a series of reports on the relation between microscopic composition and chemical and physical properties of banded bituminous coals. It describes the relation between microscopic composition and behavior during thermal decomposition of a heterogeneous, high-volatile A bituminous coal from the Chilton bed in West Virginia. The standard free-swelling test was used as a simple means of studying the effect of heat on the coal. Although swelling indexes are not precise indicators of coal behavior in the coke oven and have limited value in caking investigations, they are reliable for predicting expansion of coal in a fuel bed and have practical value in the study of fuels. The swelling test also supplements other useful laboratory tests for determining the plastic and expansion properties of coal.

Jan 1, 1957

By J. K. Whyatt

Researchers at the U.S. Bureau of Mines collected and analyzed overcore measurements and other indicators of in situ stress characteristics at the Lucky Friday Mine, Mullan, ID. An analysis of these data revealed that significant local variations in in situ stress are present in this mine and that these variations existed prior to mining. High stresses were found to be associated with the most competent strata and a locked section of a fault. An estimate of the predominant stress field was developed for mine-wide modeling. The estimate shows that the greatest principal stress was oriented north of northwest. This information should provide a basis for mine-wide structural modeling of the Lucky Friday Mine and should generate important insights into localized stress conditions, which may significantly affect both local and mine-to-mine variations in seismicity induced by excavation.

Jan 1, 2010

By Sigmund Black

Ingersoll-Rand Research, T n c and the Lee-Norse Co. built a Bureau of Mines sponsored, special deep cutting continuous miner under this contract to study the effects of rotational speed and depth of cut on airborne respirable dust. After preliminary tests indicated and later verified that deep cutting - low rotational speed reduces airborne respirable dust, a series of underground tests were performed (9 combinations of rotational speed and depth of cut at 45° bit angle and 4" bit spacing). Additional data was obtained on specific energy, coal sizing and noise. The conclusions reached from the tests results were; a) deep cutting reduces airborne respirable dust generated and specific energy needed to cut coal., b) the greater majority of the decrease occurs in going from 1" to 2" depth of cut, c) lowering rotational speed has a particularly sizable effect of reducing the amount of dust at the operator's location, d) no significant relationship was found for either noise level or coal sizing to rotational speed or depth of cut. Recommendations include. a)) use of specific energy as an indicator of the change in dust level correlating to changes in cutting parameters, b) mine operators should acquire new deep cutting machines., since retrofitting would be selective.

Jan 1, 1977

By R. L. Merek

There were 63 fatalities in the California petroleum industry in 1929, the largest number in any year since 1923 and an increase of 34.0 per cent over 1928, when 47 men lost their lives in the drilling, producing, manufacturing, and marketing divisions of the industry. It will be observed from the accompanying chart that after following a consistent decline for 4 years, the fatality curve turned upward in 1923 and advanced sharply in 1929. Although this increase in fatalities coincided with a period of intensive development it tends to indicate some laxness in the industry during a period of increased hazards. Intensive drilling campaigns are usually started hurriedly and conducted with a great demand for speed, and the result is that accident-prevention work is too often relegated to a position of minor importance.

Jan 1, 1930

By R. L. Marek

There were 63 fatalities in the California petroleum industry in 1929, the largest number in any year since 1923 and an increase of 34.0 per cent over 1928, when 47 men lost their lives in the drilling, producing, manufacturing, and marketing divisions of the industry. It will be observed from the accompanying chart that after following a consistent decline for 4 years, the fatality curve turned upward in 1923 and advanced sharply in 1929. Although this increase in fatalitics coincided with a period of intensive development it tends to indicate some laxness in the industry during a period of increased hazards. Intensive drilling campaigns are usually started hurriedly and conducted with a great demand for speed, and the result is that accident-prevention work is too often relegated to a position of minor importance. [ ]

Jan 1, 1930

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date and is being published as a similar series of seven miners' circulars (Nos. 51-57, revised) on accident prevention in metal and nonmetallic mines. These circulars are: Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the use of investigations and reports of all accidents.

Jan 1, 1957

By A. Sainato, S. J. Kravits, G. L. Finfinger

This report describes a project conducted by the Bureau of Mines in which the accurate directional drilling of a borehole was demonstrated with the objective of intercepting a designated target. The project was conducted at Navajo Dam in northern New Mexico at the request of the Bureau of Reclamation. Borehole survey and drill logs are provided in an appendix. The trajectory of the demonstration borehole was designed to intercept a 5-ft-radius target at the final or "punchout" distance of 885 ft. The elevation of the borehole at this distance was within the target; the borehole punchout coordinates were 8.81 ft southwest of the target. As a result of the demonstrated accuracy, the Bureau of Reclamation has contracted the accurate drilling of boreholes as long as 600 ft from the inside of a short tunnel, to control water seepage in the right abut- ment. This resulted in a substantial cost savings compared to the orig- inal plan of constructing a longer tunnel and drilling 150-ft boreholes.

Jan 1, 1987

By Henry P. Wheeler

As recently as 1915, helium was available only in very small quantities at a cost equivalent to $2,500 per cubic foot. It was a laboratory curiocity, and its properties were of interest to a limited number of scientists (11).3/ During the past 30 years, however, helium has grown from a plaything of scientists to a factor of importance in the prosecution of the recent war. Navy blimps filled with nonflammable helium proved to be more than a match for German submarines operating in the Atlantic. American bombers were able to fly unheard-of distances to drop bombs on Tokyo, Nagoya, Yokahama, and other Japanese cities because they had been made lighter with magnesium, arc-welded in a helium atmosphere. The Army utilized helium-filled radio-sonde balloons to obtain vital information concerning weather conditions affecting D-day invasions and other military maneuvers.

Jan 1, 1946

By B. W. Gandrud

[The Bureau of Mines is conducting an extensive investigation of coal preparation in the Alabama coal fields in cooperation with the University of Alabama and coal-mine operators. In this investigation the drainage characteristics of typical coals from the Warrior and Cahaba n fields were studied. Tire main purposes of this study has been to evaluate no nearly as possible relative influences of certain factors on rate of drainage and to determine whether the drainage characteristics of coals from different beds or from different mines on the soma bed differ materially. A further objective was the development of a laboratory drainage test that would predict approximately the rate at which any coal will drain after having been loaded into a railroad car in a saturated condition. The study has been confined to samples of slack coals - that is, coals from which none of the fine sizes have been removed. The samples ranged in upper size limits from 7/16 inch to 3 inches. It did not seem necessary to study nut and egg sizes, that is, sizes from which the fine coal has been removed by screening, as these lose water so rapidly by natural drainage that they present no serious problem in dewatering after treatment in a washer. The significance of drainage characteristics of Alabama coals is apparent in view of the fact that not less than 70 percent of Alabama?s total coal product is subjected to wet washing before being materials.]

Jan 1, 1941

By A. H. WHITE, PERRY BARKER

In a consideration of the various means whereby more economical and more efficient use may be made of the fuels in the United States, the possibility of obtaining for the production of illuminating gas other and cheaper fuels than the Pennsylvania coals demands attention. For the Government, as well as for private corporations and the householder, there can be no more economical and efficient way of using some coals than through the medium of illuminating gas. In the stove, gas reduces the labor cost of heat production and lessens the drudgery of the kitchen; burned in the Welsbach mantle, it is an excellent and cheap illuminant. In addition, the coke that remains after the gas has been recovered furnishes a smokeless fuel that has about the same heating value as anthracite. Hence any investigations that will indicate how local coals through proper treatment may be substituted for the higher priced and rapidly vanishing Pennsylvania gas coals will bring about lower prices for both gas and coke and will also aid to conserve for use in metallurgical processes the coking coals of Pennsylvania and of ot,her States. The annual drain on the gas-coal resources of this country and the importance of the gas and coke industries are indicated by the fact that 8,390,129 tons of coal were carbonized in retorts in the United States in 1909. The resulting salable products from by-product ovens were 15,791,220,000 cubic feet of coal gas, 6,254,644 tons of coke, and 60,126,000 gallons of tar. The total value of all by-products was about $28,508,637.

Jan 1, 1911

By Robert F. Chaiken

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,000° C (1,832° F), and can be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900's and was surface mined in the 1940's. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated, but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project, to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fourth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 3, 4, and 5). Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. This part (part 4) and part 5 both deal with the closeout phase of the field demonstration. The quenching of the fire is described in this report, and part 5 will describe the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration, which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection with fume exhaustion is a potentially effective method for cooling large underground fire zones. Further trials of both Burnout Control and water injection with fume exhaustion are planned.

Jan 1, 1984

By J. H. East, D. Harrington

"INTRODUCTION The tremendous expansion of industry during the war and the unprecedented demands for metals and minerals are reflected in the production and use of explosives during that period. The increased use of explosives brought added safety problems to industry because of the necessity of using men as blasters who were not entirely familiar with and some who were totally unfamiliar with the characteristics of some or all of the various explosives. A discussion of the characteristics of the ordinary types of explosives used in: industry should assist in giving a better understanding of the hazards attending their use. Explosives are compounded so they may be used with reasonable safety provided the user understands and follows the procedure recognized as standard safety practice. Short cuts and the failure to understand and use recognized safe practices, as well as the selection of explosives unstited for the work at hand, are all part of the safety problem,The extent to which explosives are used in the United States is shown by a study of the statistics compiled by the Bureau of Mines 4/ regarding them. Some of these statistics are shown below and serve as an indicator of the tremendous number of men engaged in the transportation, storage, and use of explosives. Theme men are exposed to the inherent hazards attending this occupation and they should be familiar with the recognized safe practices relative to explosives."

Sep 1, 1946

By Frank G. Horino

A rock mechanics program (composed of laboratory and field tests) was initiated by the Bureau of Mines in an effort to determine the causes of pillar instability at the Fletcher mine, near Bunker, Mo. Compressive strength, Young's modulus, shear strength, and the angle and coefficient of internal friction were determined on drill cores obtained from 16 different locations in the mine. Results of the laboratory tests showed that highly mineralized zones and brecciated zones in pillars could significantly affect pillar strengths and stability in locations where extraction ratios exceeded the normal design ratio of approximately 78%. High-angle fractures that were present in Some locations also may have contributed to pillar deterioration. In the field tests, in situ stress determinations were made in one pillar to establish the pillar-loading conditions and to evaluate the stability of the pillar. Continued monitoring of stresses in the pillar showed a gradual decrease in compressive stress, indicating that the pillar was probably in the postfailure state. A second stress determination was made in a vertical hole in the underlying igneous rock that was exposed on one section of the mine. Horizontal stresses were compressive and larger than would be expected from gravity loading.

Jan 1, 1978

By Walter W. Kaufman

This User's Manual, extracted from information contained in the Final Report for the above referenced project, outlines test procedures to measure the braking capabilities of underground non-coal rubber-tired mining equipment. Methods to interpret test results, recommendations for safe braking capabilities, and basic techniques to improve braking systems and road surfaces are also discussed. Possible applications for runaway vehicle protective devices other than braking systems are reviewed. Also included is a listing of mining equipment and brake component manufacturers who supply the majority of equipment to the United States non-coal mining industry. In conjunction with this list of manufacturers, a general tabulation of brake related specifications appears for vehicles observed during stopping tests conducted underground.

Jan 1, 1977

By T. F. Anstett

The Bureau of Mines estimated the potential availability of rare-earth oxides (EtEO), including yttrium, and thorium, which is also contained in the rare-earth bearing minerals monazite and bastnasite, from 38 'properties in market economy countries (MEC's). Only nine of the properties evaluated produce or would produce REO as the primary product; the others contain REO as a byproduct, chiefly from mineral sands operations recovering rutile, ilmenite, and zircon. Nearly 77% (2,578,000 mt) of the total 3,355,000 mt of recoverable RE0 evaluated is from producing properties. It is estimated that 21% (705,000 mt) of this total is from properties that could not realize a positive rate of return at the January 1984 market prices for the recovered commodities. At production capacities assumed for this evaluation, the amount of RE0 potentially available from producers ranges from an estimated 46,500 mt in 1986, to a peak of 50,900 mt in 1992, to 49,900 mt by the year 2000. Total MEG production in 1984 was estimated at 40,700 mt. Assuming demand does not increase sharply, producing properties can continue to fulfill overall REO demand through at least the end of this century.

Jan 1, 1986

By J. E. Schiller

The Bureau of Mines is investigating methods to treat waste water that contains cyanide. This report describes a new method that removes heavy metals and all forms of cyanide. In the first step, hydrogen peroxide and sodium thiosulfate are added at pH 7 to 9 in a 1:2 molar ratio to convert free and weakly complexed cyanide to nontoxic thiocyanate. Then steryldimethylbenzylammonium chloride is added to precipitate ferro-cyanide, and finally, ferric sulfate is added as a sweep floc and sequestrant for heavy metals. After the suspended solids settle, the water is polished by filtering. The water initially contained 1 to 5 mg/L Fe, 1 to 5 mg/L Cu, and 10 to 30 mg/L total cyanide; the level of each of these constituents was reduced to less than 0.02 mg/L.

Jan 1, 1983