Search Documents

By Fred W. Johnson

The first section of this circular has been prepared with a view to answering inquiries frequently received by the Bureau regarding laws governing the staking of claims and regulations covering requirements for holding them and obtaining title in fee to placer ground. These laws and regulations were summarized briefly in Information Circular 6796, "Placer Mining in the Western United States." These laws, however, are administered by the General Land Office, Department of the Interior, and it has been considered advisable to combine an authoritative résumé thereof by the Commissioner of that Bureau with information on small-scale placer mining previously published by the Bureau of Mines. The second section of this circular is largely a revised reprint of Information Circular 6611, "Small-Scale Placer Mining Methods", first published in April 1932 for the purpose of answering the many daily inquiries then being received on this subject. This circular has been reprinted repeatedly, and about 30,000 copies have been distributed, most of them in response to applications therefor. At present (June 1937) requests for this publication continue to be received daily.

Jan 1, 1938

By G. E. McElroy

Tae purpose of this paper is to present types of charts adapted to aid in the graphic solution of fan-performance problems of selection and operation, and to urge the adoption of similar charts by the National Association of Fan Manufacturers as standard forms for presenting fan-performance data. As matters now stand, it is difficult for the average engineer to solve such problems because a laree number of variables are involved, and performance data are not presented in a manner that permits their direct application to many problems encountered in practice. The performance of any centrifugal machine is determined not only by the machine itself but also by the fluid-flow system on which it operates. Actual performance of centrifugal fans is therefore e matter of the type, size, and speed of fan, on the one hand, and of the relation of pressure to quantity of flow, as determined by the physical condition of the airway system, on the other.

Jan 1, 1936

By G. E. McElroy

[The purpose of this paper is to present type: of charts adapted to aid in the graphic solution of fan-performance problems of selection and operation, and to urge the adoption of similar charts by the National Association of Fan Manufactures as standard forms for presenting fan-performance data. As matters now stand, it is difficult for the average engineer to solve such problems because a large number of variables are involved, and performance data are not presented in a manner that permits their direct application to many problems encountered in practice. The performance of any centrifugal machine is determined not only by the machine itself but also by the fluid-flow system on which it operates. Actual performance of centrifugal fans is therefore a matter of the type, size, and speed of fan, on the one hand, anti of the relation of pressure to quantity of flow, as determined by the physical condition of the airway s: stem, on the other.]

Jan 1, 1936

By Larry A. Haas

The U.S. Bureau of Mines, in cooperation with Cleveland-Cliffs, Inc. (Hibbing, MN), investigated ways of enhancing the quality (compressive strength, after-tumble and reducibility) of domestic acid and fluxed magnetite pellets by modifying the oxygen content during the preheat and induration periods of the firing operation . Oxidation of magnetite was best accomplished when sufficient oxygen and time were available before the peak induration temperature was reached. The rate of magnetite oxidation increased directly with the gas oxygen content during the preheat period at 7000 C and above. With 30 pct ( or more) O2 and a preheat rate of 2000 C/min, most of the magnetite was oxidized during the preheat period. With laboratory tube and mini-pot furnace tests, oxygen enrichment during the preheat period improved the pellet properties more in the simulated grate-kiln tests than in the simulated straight-grate tests. The longer induration period with the grate-kiln test resulted in more sintering of the residual magnetite and its reaction with the silicon compounds. When flux was present in the pellets, calcium silicates and calcium and magnesium ferrites were formed. More calcium ferrite was formed when the magnetite was oxidized early and less iron was present in the fayalitic calcium silicate slag.

Jan 1, 1993

By T. F. Myners

This paper, describing the concentration methods and costs of Witherbee, Sherman and Company at Mineville, N. Y., is one of the series of papers on milling methods and costs being prepared by the United States Bureau of Mines. It deals principally with the production of high-grade concentrate. ACKNOWLEDGMENT The author is indebted to C. F. Jackson, principal mining engineer, United States Bureau of Mines, to A. M. Cummings, general superintendent of Witherbee, Sherman and Company, and to the company's engineering staff, for assistance in preparing this paper.

Jan 1, 1932

By J. B. Cunningham

Lithium in the form of metal, salts, and alloys is particularly important because of increasing industrial uses resulting partly from wartime developments. Lithium carbonate and lithium strontium nitrate, which impart a brilliant red color to a flame, are used in pyrotechnics. Lithium chloride and fluoride are used in fluxes for welding aluminum to dissolve the oxide coating on the aluminum and prevent oxidation of the molten metal. Lithium carbonate is used in ceramics in raw alkaline glazes because of its unusual fluxing properties. The use of 9 to 12 percent lithium carbonate permits a marked increase in the amounts of alumina, calcium, and silica that may be Used and results in a more stable glaze with sufficient alkalinity to produce vivid copper blues and other typically alkaline colors. Lithium stearate is used as a grease in airplane engines because of its ability to withstand wide changes in temperature. In view of its great affinity for nitrogen, hydrogen, oxygen, sulfur, phosphorus, carbon, and silicon, lithium has an excellent scavenging action on molten metals. It forms stable nonmetallic compounds of low specific gravity or gases that are eliminated at pouring temperatures. Lithium is generally added to the melt in the form of a lithium-calcium alloy consisting of 50 percent of each ingredient or as an alloy of 98 percent copper and 2 percent lithium. The lithium-calcium alloy added to cast iron before pouring, acts as a scavenger and increases the fluidity of the melt. This alloy also is said to increase the corrosion-resistant properties of stainless steel alloys and to improve their polishing qualities.

Jan 1, 1948

By D. C. Dahlin

The U.S. Bureau of Mines investigated the magnetic susceptibility of minerals as a function of mag-netic field strength to determine how it might affect the potential for high-field magnetic separation as an alternative to other separation technologies. Single-mineral concentrates were prepared from specimens from the same deposit to compare magnetic susceptibilities of minerals that occur together and from specimens from different deposits to compare magnetic susceptibilities of like minerals. A vibrating-sample magnetometer with a superconducting magnet capable of producing a magnetic field of 7.16 x 106 Aim (90 kOe) was used to measure the magnetic moment of the samples. The data were then converted to specific magnetic susceptibility data and plotted as a function of magnetic field strength. Cursory studies were also completed on the effects of iron content and oxidation roasts on magnetic susceptibility in high fields. The results showed that magnetic susceptibility is essentially constant in magnetic fields above those needed to saturate ferromagnetic constituents. Although magnetic susceptibility is influenced by iron content and by thermal treatment, the changes are not large enough to influence separations in fields above 1.59 x 106 Aim (20 kOe).

Jan 1, 2010

By W. J. Wiehagen

The Work Crew Performance Model (WCPM) seeks to define performance variability within similar tasks of an underground work crew and relate observed variability to a cost consequence. Performance variability is described using work site observations to determine the adherence to job elements con¬tained within a standard operating procedure. Key components of the WCPM include (1) job definition through task analyses and the ranking of job elements by perceived cost consequence, (2) observational techniques for establishing performance baselines by measuring adherence to safe and proficient job procedures, and (3) cost linkages between adherence to task procedures and measures of consequence for noncompliance. Data presented within this report were obtained through the study of shuttle car operation in an underground mine in Appalachia. Observed adherence to safe and proficient job procedures by opera¬tors matched well with the consensus profiles (measured through a nominal group technique) with min¬ing personnel. It was also found that experienced operators consistently outperformed less experienced, incidental operators. These findings imply potential use of the WCPM as a practical procedure for thinking systematically about the choices available to reduce performance variability. Field application of the model can offer useful data to evaluate training and financially support performance improvement strategies that can be tested for their ability to reduce human error.

Jan 1, 1994

By Raymond W. Hiteshue

To aid in designing a continuous system for evaluating processes for converting coal to high-Btu gas] the Bureau of Mines determined the amenability of various coals and a char to hydrogasification at 800° C and 6,000 psig using a molybdenum catalyst. A lignite from Rockdale, Tex., an hvCb coal from Rock Springs, Wyo., a char from the low-temperature carbonization of the latter, an hvAb coal from Pittsburgh, Pa., and an anthracite from Luzerne County, Pa., were selected. Highest yields of gaseous hydrocarbons, 94 pet, based on maf feed, were produced from char, and lowest yields, 67 pct, were obtained from lignite. Hydrocarbon gases contained 82 to 92 pct methane, 8 to 15 pct ethane; and 1 to 3 pct propane.

Jan 1, 1962

By Fraser M. Walsh

The objective of this program was to determine by laboratory experiments the kinetics and mechanics of the reactions that produce acid in coal mine drainage. The program was divided into three phases: In Phase I, five coil mines, representative of Appalachian coal mines, were chosen for sampling and an experimental design was identified suited to accomplish the program objectives. In Phase II, the five mines were sampled and test protocols applied. The results showed most pyrite weathering to be based on oxidation in the presence of water. Iron bacteria, especially Thiobacillus ferrooxidans, catalyzed the rate of pyrite weathering by a factor of three. An increase in initial iron concentration in a system that modeled the nine environment acted to inhibit bacterial catalysis of weathering. In Phase III, five tailings piles were sampled and the material obtained was used to evaluate this method of bacterial catalysis inhibition. The evaluation verified method effectiveness; inhibition of over 80% of the release of weathering products was observed.

Jan 1, 1982

By B. D. Nash

The object of this research was to investigate the technical feasibility of preparing chromium metal by the thermal decomposition of bisbenzene chromium. Bisbenzene chromium, a pi-bonded sandwich type organometallic compound, was thermally decomposed under reduced pressure to form a metal plate on a heated substrate. Metal recovery was close to 100 percent of theoretical, with deposition rates up to 20.8 mg/hr/cm2. Metal purity was dependent not only upon the purity of the starting material, but also upon the sublimation rate of bisbenzene chromium. Total detectable metallic impurities ranged from a low of 18 ppm to several hundred ppm. In general, metallic impurities were less than 100 ppm. Carbon, the major nonmetallic impurity, ranged from less than 0.3 percent to more than 10 percent. The carbon contamination is most likely a result of the decomposition of the organic portion of bisbenzene chromium. An unusual property of some of the deposits was their outstanding corrosion resistance. Unlike pure electrolytic chromium, which dissolves readily, these deposits were insoluble in hot mineral acids.

Jan 1, 1968

By H. W. Sheffer

Technical and economic aspects of community refuse disposal systems and their effects on the environment are identified and described. Seven landfills and two incineration systems, located throughout the United States, are reviewed.

Jan 1, 1971

By A. Z. Dimitroff, A. C. Moschetti

An improvised rock- dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jun 23, 1964

By Paul C. McWilliams

This Bureau of Mines report analyzes data on the physical properties of quartzite rock from the Crescent mine, Coeur d?Alene mining district, Kellogg, Idaho, to demonstrate the use of multivariate techniques. After regression, factor, component, cluster, and discriminant analyses are discussed, these techniques are applied to the Crescent mine data. Three appendixes contain some of the required mathematical and statistical detail plus heuristic examples of three multivariate techniques --component, cluster, and discriminant analysis.

Jan 1, 1978

By C. E. Wicks, F. E. Block, F. D. Stevenson

The vapor pressures of tungsten (VI ) chloride ( WC1 ) and hafnium ( IV ) iodide ( HFI ) were measured by a metal diaphragm technique . Vapor pressure values were obtained to permit calculation of the thermodynamic properties of the vaporization processes of the compounds . The vapor pressure data of WC16 are represented by the following equations for the liquid , B - solid , and a- solid over the temperature intervals indicated : - log P = 8.194 3,253 /T Liquid , 281.5 ° to 325 ° C : B - solid 230.0 ° to 281.5 ° C : log P a - solid 185.0 ° to 230.0 ° C : log Pam *** = 8.794 - 3,588 / T = 9.615 - 3,996 /T where T is the absolute temperature in degrees Kelvin . The heats of vaporization and sublimation are 14.9 , 16.4 , and 18.3 kcal / g mole , respectively . The entropy of vaporization at the normal boiling point , 330 ° C , was 24.3 eu . The fusion temperature , 281.5 ° C , and transition temperatures , 230.0 ° and 185 ° C , were found by thermal analysis .

Jan 1, 1964

By Lowell L. Patten

The Federal Bureau of Mines participated with the National Aeronautics and Space Administration and Martin Marietta Aerospace in developing, building, and testing a portable X-ray fluorescence spectrometer for use as an analyzer in mineral-resource investigative work. The prototype battery-powered spectrometer, measuring I1 by 12 by 5 inches and weighing only about 15 pounds, was designed specifically for field use. The spectrometer has two gas-proportional counters and two radioactive sources, 109Cd and 55Fe. Preliminary field and laboratory tests on rock specimens and rock pulps have demonstrated the capability of the spectrometer to detect 33 elements, to date. Characteristics of the system present some limitations, however, and further improvements are recommended.

Jan 1, 1982

By Pedro Lilienfeld

This report describes a program whose objective was to develop, design, fabricate and laboratory-test two prototype instruments capable of real-time selective detection and measurement of airborne fibrous-shaped particles. The operation of this fibrous aerosol monitor (FAM) is based on the rotation imparted to the acicular particles by means of a rotating quadrupole electric field of the order of 3000 V/cm. This field induces a dipole charge separation on the fibers and aligns them with the applied field. The selective detection of the fibers is effected by synchronous detection of the resulting modulation of the light scattered from a continuous-wave helium-neon laser beam by the rotating particles. The theory of operation, design of the electric-optical detection configuration and the electronic signal processing method are discussed. By means of a scattering pulse sharpness discrimination technique, fibers whose length exceed a selectable value are detected and their number concentration digitally displayed. Counting times of 1 to 1000 minutes permit the measurement of fiber concentrations between 0.001 and about 30 cm-3. A concentration of the order of one fiber per cubic centimeter can be assessed within a relative standard deviation of 10 percent with a counting period of 10 minutes. The FAM is a portable, battery-powered instrument capable of operating continuously for about 4 hours between battery charges. Preliminary tests with crocidolite and crysotile asbestos as well as with glass fibers were performed in the laboratory and the results indicate good correlation with the standard NIOSH phase contrast microscopy filter counting method.

Jan 1, 1977

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

By H. W. Kilau

The Bureau of Mines tested chromium-bearing waste slags from industrial stainless steel and other chrome alloy operations to determine their chromium leachability characteristics under acid precipitation conditions and to devise measures to prevent any pollution originating from this source. Two critical slag composition factors were found to control the chromium leachability: (1) CaO:Si02 ratio and (2) magnesium content. Above a 2.0 CaO:Si02 ratio, chromium exists in slag as CaO·Cr203, which can be vulnerable to leaching by acid precipitation especially if oxi-dized to CaCr04 when exposed to the environment over an extended period. Maximum chromium leachability from industrial slags occurred when the composition of the slag had about a 2.0 CaO:Si02 ratio. Between a 1.0 and 2.0 CaO:Si02 ratio, in the presence of sufficient magnesium, MgO ·Cr203 was formed, which is very resistant to oxidation and to dissolution by simulated acid precipitation. Addition of magnesium silicates to molten slag to fix the chromium in the MgO·Cr203 form was successful in preventing chromium leaching in simulated acid rain solutions. Experiments showed olivine and waste taconite tailings were suitable for this purpose. Olivine addition to a waste slag having a composition vulnerable to leaching (CaO:Si02 > 2) reduced the chromium leachability more than 80 pct.

Jan 1, 1984

Fresh coal refuse was sampled at 21 US mines. Five of the sites were drilled, sampled and tested more extensively. Field tests included Standard Penetration tests, and in-situ density determinations. Laboratory testing included specific gravity, gradation, maximum, and minimum density tests, as well as 9-inch) drained triaxial tests, 9 and 10-inch, permeability tests, slake-durability tests, and accelerated slaking tests. Some refuse sites had significantly lower shear strengths and permeabilities in old, slaked or weathered material than in fresh refuse. Testing did not show useful correlations between strength and permeability changes and other material properties which could serve as "predictors". Testing of refuse under "accelerated slaking" conditions showed promise as a comparative tool and as a potential means of preparing artificially aged samples for evaluations of long-term behavior. The state-of-the-art in slaking research, and the implications of slaking on coal refuse disposal, and on practical methods of managing slaking, were also studied.

Jan 1, 1981