Search Documents

By O. C. Blade

This report on the properties of motor fuels sold through service stations In the United States was made In accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items Is confidential. 1t presents analytical data for 4, 802 samples, representing the products of 117 companies. The samples were collected during December 1954 and January and February 1955. As in previous surveys, the gasolines covered 6y this survey Include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation, A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1955

By Clifford B. Farris

The natural cementation strength of retorted oil shale is the focus of this investigation. The optimum retorting temperature and residence time to obtain natural cementation strength in retorted Green River oil shale from western Colorado were determined as follows: [Optimum Conditions for Natural Cementation Maximum Residence Obtained Retorting Time at Compressive Mode of Temperature Temperature Strength' Retorting °F °C hr psikg/cm-2 Direct 1,520 822 2.0 270 19.0 Indirect 1,530 832 2.9 325 22.8] 1 Scattered samples were tested at strengths as high as 463 psi (32.6 k /cm 2) (Run 8, indirect mode) and 406 psi (28.5 kg/cm2) (Run 48, direct mode), but these high strengths were not confirmed by nearby tests. Minus 0.5-inch (1.3-cm) Green River oil shale was heated in a differential retort under conditions simulating potential full-scale retorting processes. The variables investigated were retorting temperature, residence time, retorting mode, and shale grade. Samples of the retorted Green River oil shale were moistened to optimum plus 2% (25%) moisture, compacted to 95% Proctor density, sealed and cured at 100°F (38° C) for up to 40 days. Lower curing temperatures, which are likely in the field, would probably result in significantly slower development of cementation strength, and might lower the ultimate strength developed. However, these effects were not studied in this project. The cured samples were tested for compressive strength, and correlative equations were developed for the increase of compressive strength with curing time as a function of retorting temperatures and residence time. Petrographic analysis indicated that the cementing mechanisms may be the interlocking growth of acicular hydrated calcium aluminum sulfate crystals between the contacts of retorted shale fragments. Samples of the retorted shale were also tested for optimum Proctor density and moisture. Permeability and quality of the leachate of shale from typical runs were determined. The effect of use of retort rather than tap water on compressive strength and leachate after curing was determined. The retorted shale effectively filtered several mineral constituents from the retort water.

Jan 1, 1979

Research 86 highlights significant studies conducted during the past fiscal year at Bureau facilities and offices. Readers who want more information about the projects and studies summarized here can contact the researchers whose names and locations appear with each summary. General information on Bureau of Mines programs is available from the Office of Technical Information 2401 E Street, NW., Washington, DC 20241. A listing of principal officials, a location map of field facilities, and a selected bibliography of publications and patents issued on Bureau developments during the past 3 years are provided.

Jan 1, 1986

By D. Harrington

The record of fatalities from mine explosions during the past 2 fiscal years has been anything but encouraging; more men were killed by explosions (379) than were killed from the ante cause during to' preceding 6 years combined (368). The reason for the large increase in the number of explosion fatalities during the past 2 years as compared with the previous 6 years is not entirely clear. In some instances, there has been laxity in the enforcement of State mining laws; in others, both workers and operating officials is have failed to observe recognized precautionary measures to prevent explosions. In many of the explosions that lave occurred within the asst few years in mechanized mines it has been evident that speed of operation and a demand for maximum tonnage at minimum cost resulted in neglect of ordinary safety measures.

Jan 1, 1942

By P. M. BIDDISON, G. G. Oberfell, George A. Burrell

The Bureau of Mines is conducting a series of investigations, with a view to ascertaining the most efficient methods of obtaining gasoline from petroleum and natural gas. This report deals with a method of extracting gasoline from natural gas by absorbing the gasoline in oil and subsequently separating it from the oil by distillation. The process is quite different from those of compression and condensation which have been used for a number of years for extracting gasoline from casing-head natural gas, and has not heretofore been described in the literature. MANUFACTURE OF GASOLINE FROM CASING-HEAD GAS. The extraction of gasoline from casing-head natural gas by compression and condensation methods has become a large and lucrative industry in this country. In the year 1915 about 65,000,000a gallons of gasoline prepared by these methods was placed on the market. In addition, in marketing this gasoline, at many plants an equivalent quantity of naphtha was blended with the gasoline, thereby utilizing for automobile fuel and other purposes a large quantity of naphtha that otherwise would have been unsuited for these purposes. The increase for the year 1915 over 1914 was about 22,000,000 gallons. For the year 1916 the production should be more than 100,000,000 gallons. The quantity of casing-head gas treated in the year 1915 by compression and condensation methods amounted to about 24,000,000,000 cubic feet; the average yield of gasoline was 2.57 gallons per 1,000 cubic feet. b This casing-head gas represents natural gas that formerly went largely to waste; hence the process represented a distinct and important step in the utilization of the natural gas produced in this country.

Jan 1, 1917

The lignite deposits of the United States represent a huge potential source of fuel for power generation. It has been estimated that lignite constitutes about 24 percent of the remaining National reserves of solid fuel on a tonnage basis and about 15 percent of the reserves on a B.t.u. basis. (See sec. 3, part 1.) The major portion of these reserves is in North Dakota. Lignite has been used locally for domestic heating since the first settlers burned it at forts and fur-trading posts as early as 1855. Some of the first studies of the use of lignite in steam boilers were conducted by the Federal Bureau of Mines from 1910 to 1920 (15, 19) 1/ However, the commercial utilization of lignite as fuel for producing power developed slowly. Not until about 1925 was any really successful lignite industrial fuel-blaming equipment developed. Since then the commercial use of lignite as a fuel for producing power has been increasing steadily.

Jan 1, 1954

By V. Vern Hutchison

This selected list contains 829 entries with citations to Bureau of Mines publications related to petroleum and natural gas, which were released during the 1961-1970 period. Some entries are multiple in nature, resulting in a total of 881 citations.

Jan 1, 1972

By H. F. Yancey

The investigations described in this bulletin are confined to a study of the washing characteristics of bituminous coals. The major part of the work was conducted by the Bureau of Mines in cooperation with the Engineering Experiment Station of the University of Illinois and the State of Illinois Geological Survey Division between 1918 and 1924, in accordance with the provisions of an agreement between these agencies. The washing characteristics of coals from many of the important coal-producing fields of the Eastern and Central States were examined. The coals of the Pacific Northwest States and Alaska have been studied separately by McMillan and Bird of the Northwest Experiment Station of the Bureau of Mines at Seattle in cooperation with the College of Mines of the University of Washington.2 OBJECT OF INVESTIGATION The object of the investigation of coal preparation by the Bureau of Mines has been to promote the production of better prepared coal and to facilitate the correct selection and design of coal-preparation plants by obtaining as complete information as possible regarding the washability of the various types of American coals and the treatment best suited to each. In addition, some attention has been given to the development of new methods of washing coal. The work naturally divides itself into three rather distinct steps: (1) Development of a systematic method of examining and testing a coal; (2) classification of the American coals on a basis of the occurrence of the impurities associated with the coal in the beds; (3) examination of one or more representative coals of each type.

Jan 1, 1929

By W. J. Wenger

Analytical, geographical, and geological data on 67 samples of crude oils from Utah are presented, along with some correlations and interpretations. Most of the, geologic formations that produce oil in other areas are also productive in Utah; and as in many other locations, the Permian, Pennsylvanian, and Mississippian formations account for the major amount of the total oil produced in the State. Some anomalies and unusual phenomena are noted. Although most Utah oils are low in sulfur, a sample containing the highest percentage of sulfur ever recorded by the Bureau of Mines is among the oils discussed in this paper. Most of the oil from the major producing formations in Utah is low in sulfur; the same formations produce high-sulfur oils in adjoining Rocky Mountain States. Some Utah oils are both waxy and asphaltic, an unusual combination of characteristics. Correlation index curves for some oils are shown suggesting compositional differences in oils from different producing formations. Production statistics trace the rapid rise of oil production in the State after the first commercial discovery in 1947 and indicate a decline in amounts produced since 1959, the year of peak production in Utah.

Jan 1, 1971

By C. M. K. Boldt

The Bureau of Mines studied the compaction characteristics of metal and nonmetal tailings. Densities of the tailings and zone of compaction influence, compactive effort, and cost of equipment are related to changes in the factor of safety for specific grain-sized tailings and embankment configurations. Field testing was accomplished in two distinct phases. The first phase investigated the effectiveness of using a nuclear gauge on metal and nonmetal tailings to produce rapid, instantaneous measurements of moisture content, wet density, and dry density. The results of the nuclear gauge testing are presented in chapter 1. Chapter 2 presents a comparison of the compactive effectiveness of three different pieces of construction equipment on a coarse-grained metal tailings pond. The three pieces of equipment chosen for study were a DBH track-mounted dozer, a DSOO rubber-tired dozer, and a SP848 vibratory smooth-drum compactor.

Jan 1, 1985

By Dean E. Bluman

The Bureau of Mines investigated the convective heat transfer coefficients for recirculated suspensions of 30-micron glass beads in inert gas. Coefficients for the suspensions were not significantly higher than coefficients for the pure gas. Reynolds numbers of the suspensions were 20,000 to 35,000; solids loadings ranged from 0.0 to 0.7 pound per pound of gas. Comparison of the results with published data showed the direction of heat flow to have no effect at the test conditions.

Jan 1, 1967

By Ronald D. Hill, Elmore C. Grim

Coal-haul and mine access roads are defined as any road constructed, improved or used by the operator (except public roads) that ends at the pit or bench. These roads constitute approximately 10% of the total area directly disturbed by the surface mining operation(l). In some cases, the land disturbed by haul roads exceeds the area included in the mining operation. Studies (2 and 3) of the U. S. Forest Service in eastern Kentucky show that typical contour mining roads exhibit poor alignment, excessive grades, insufficient strength and durability, and poor drainage. Mine roads in other Appalachian- States, particularly where contour mining is practiced, appear much the same as those in Kentucky. Access roads(4) were also found to be a large source of sediment. It is possible that of the sediment that finds its way into the streams as much (or even more) originates from the haul roads as from the mining operation. Most roads are built as cheaply as possible, and good road-building design and practice are ignored. Maintenance schedules are generally inadequate, and upon completion of mining, haul roads are usually abandoned, with little or no attempt made to bed them down(5 ) . Such roads deteriorate very rapidly (Figure 68). Area mining, which is practiced in flat to gently rolling terrain, presents fewer haul road related environmental problems. These roads through necessity are generally well engineered because of the heavy equipment using them, such as 240 ton (217 metric ton) haul trucks. They must have wide beds, good alignment, and adequate drainage to permit coal haulers to run at top speed during all seasons of the year. Excessive dust can be a public nuisance and a driving hazard, and it is hard on equipment. Calcium chloride and sodium chloride have proven to be effective materials for controlling dust. Two applications during the summer when the ground surface is moist at the rate of 1/2 pound per square yard (.26 kilograms per square meter) (3 1 have been suggested. Th4 most common procedure is to keep the roads wet by using water trucks. Sediment that reaches the streams can be traced to one or more of the following five basic phases of haul-road life:

Jan 1, 1974

By Scott W. Hazen

METHODS of determining the grade and tonnage in a mineral deposit have not kept pace with scientific developments in certain other fields. The most commonly used methods of computing ore reserves and grade based on diamond-core-drill sampling are the cross section, the polygon, and the triangle. Tonnage and grade may be determined by these methods with acceptable accuracy, providing a sufficient number of samples is obtained; however, there is no means of determining when an adequate number has been taken or conversely if the deposit has been sampled excessively. It is demonstrated that, by using the techniques of statistical analysis, a mining engineer will be able to determine when a sufficient number of samples has been taken to determine the grade of a mineral deposit within a specified degree of confidence. Using statistical analysis to compute the estimated average grade of the ore makes it possible to compute a fiducial interval, when a distribution of the sample means is normally distributed, so that there is 95-percent confidence in the statement that the true average grade of the deposit is covered by the interval. This report utilizes data obtained from the Maggie Canyon manganese deposit, Artillery Mountains region, Mohave County, Ariz. Four separate exploration projects were conducted at Maggie Canyon between 1936 and 1950. Present economic conditions have made it desirable to determine the amount of 5-percent manganese ore developed by these projects.

Jan 1, 1957

By Catharine T. Fogg

The Bureau of Mines investigated the availability of flake and high-crystalline natural graphite from 4 domestic and 25 foreign mines and deposits in 11 market economy countries (MEC's). Demonstrated resources were estimated to be 95 million metric tons (Mmt) containing 5.61 Mmt of recoverable flake and high-crystalline graphite products. Fifty-five percent (3.17 Mmt) of the total recovered product is estimated to comprise plus 100-mesh (150-µm) flake pro-ducts and "lump" and "chip" high-crystalline products, designated as "graphite A" in this study; 45 pct (2.44 Mmt) of the total is minus 100-mesh (150-µm) flake products and "dust" high-crystalline products, designated as "graphite B." Total production costs, including all costs needed over the life of each operation, were determined at a 0-and 15-pct discounted-cash-flow rate of return (DCFROR) for both graphite A and graphite B products. For a 15-pct DCFROR, 1.74 Mmt (54.9 pct) of the graphite A products is available at $600/mt or less and 2.13 Mmt (67.2 pct) is available for $800/mt or less. For the same DCFROR, 1.08 Mmt (44.3 pct) of the graphite B is available at $200/mt or less, and 1.71 Mmt (70 pct) is available at $325/mt or less. No domestic resources were determined to be economic at present prices. A sensitivity analysis of the relative economics of the Alabama graphite deposits under various operational parameters is presented in an appendix. All evaluations are in January 1984 dollars.

Jan 1, 1987

By D. E. Hirsch

The Bureau of Mines, as a part of American Petroleum Institute Research Project 60, Characterization of the Heavy Ends of Petroleum, has made extensive use of gel permeation chromatography (GPC). Data developed in this study were used to develop several correlations that greatly expanded the usefulness of GPC and the data have been used as an aid in the interpretation of mass spectra (MS). GPC retention volume data on pure compounds were used with molecular structure to develop correlations that can be used to accurately predict retention volumes, molecular volumes, densities, chain lengths, and ring numbers of many components of petroleum without resorting to further laboratory experimentation. Conversely, the correlation can be used to select or reject some compounds from several possible compounds that are indicated on the basis of MS analysis. The utility of these correlations in compound type characterization is demonstrated by showing their application to 330° to 550° C fractions from a low-sulfur and a high-sulfur crude oil.

Jan 1, 1974

By Raymond O. Dannenberg

The gas-combustion retort developed by the Federal Bureau of Mines at the Rifle Oil Shale Project near Rifle, Colo., is a continuous, gravity-feed retort. The heat required to convert the kerogen in the oil shale to liquid oil is generated by the combustion of product gas and carbonaceous residue remaining on the retorted shale after the kerogen has been converted to oil, gas, and residue. A study of the effects of the process variables on retort operation, product yields, and product properties is important to the successful solution of the problems encountered in the development of a satisfactory process. Statistical methods were used to design the experiments and analyze the effects of the rate of shale throughput, the composition of dilution gas, the height of the shale bed above the air entry, air-gas distributor design, shale size range, and the ratios of the flow rates of the various gas streams entering the retort to the rate of shale throughput.

Jan 1, 1960

By R. W. Stahl, H. E. Sanford, J. B. Benson

"As movement or transportation of coal is second only in importance to actual mining, and as the latter is wholly dependent on the former, the efficiency of the haulage system often determines the efficiency of the entire plant. Safe or accident-free transportation is essential, also, because no attempt is made to divorce safety and efficiency, it being realized that they are inseparable.Most of the Ruhr mines were opened decades ago, and many features that were considered up-to-date then are now obsolete. Progress in developing haulage systems has been slow, chiefly because it would be very costly to change many to accomodate more modern equipment. These systems are being altered or modernized slowly, as capital permits. The only revolutionary changes that have been made in mine haulage are the use of larger locomo¬tives and cars, in the movement of shuttle cars, and in the adoption of skip hoisting. Most Ruhr shafts, however, will not accomodate large cars, the secondary roadways are too narrow for large locomotives, and the coal is too soft to permit skip hoisting because degradation would be too great. Therefore, notable advances have been made only at newer plants, where allowances have been made for modern equipment.The shafts are deep (average 2,300 feet) and of comparatively small diameter. The small bore was designed to reduce costs of sinking and lining. Generally, the shafts are lined throughout with masonry; however, most of the buntons and guides are wooden.The hoisting engines arc installed in masonry structures, and where more than one hoist is used they are placed on opposite sides of the shaft to eliminate as much noise as possible (fig. 1). This arrangement also prevents an engineer from acting on any signals except those transmitted to him. A few hoisting engines are mounted in the headframes (fig. 2). The hoisting engines are equipped with overwind, overspeed, and auxiliary braking devices, which are tested frequently and kept operative at all times. The signal code is displayed in view of the engineer, and a light or dial indicator informs him of the cage's position in the shaft. Many hoists are equipped with re¬cording devices, which show on a continuous chart the speed of hoisting as well as any delays throughout the 24-hour period.A Koepe system of winding is in general use because of the depth of shafts (fig. 3). With this system, a single rope passes over a single-groove, large-diameter sheave attached to the motive power, and the ends of the rope, after passing over the head sheaves, are attached to the cages. A flat tail rope suspended in the shaft and connected to the bottom of the cages serves to balance the system. Both steam and electric engines are used to activate the hoisting system, end the engines are capable of moving at least a 50-percent overload.The ropes are necessarily of large diameter (2-1/2 inches and greater), and flexibility decreases as rope diameter increases. To overcome the unwieldiness .of large-diameter ropes as shafts become deeper, a four-rope system is being tried at one mine (fig.4). In this system the load is equalized between four ropes which permits much smaller ropes to be used. All hoist ropes are inspected daily and discarded after 2 years service unless special permission for longer service is granted by the Mine Inspectorate, and then only after thorough visual and electromagnetic inspection."

Jan 1, 1950

By Charles E. Semler

The possible utility of selected compositions in the systems SrO-ZrO2-MgO and SrO-ZrO2-Dolomite for commercial refractory products was confirmed in this study. Specifically the compositions of interest are located in the sub-systems SrZrO3-ZrO2-MgO and SrZrO3-ZrO2-Dolomite. Both sub-systems have regions that are not affected by hydration, but the sub-system SrZrO3-ZrO2-MgO has a larger candidate compositional region. Solid state phase relations were determined for the subject systems over the temperature range 1600°C to 1300°C, with compatibility diagrams presented for each. The systems appear to show good refractory character with no apparent low melting compositions. As the compositions of commercial interest lie mostly in the higher ZrO2 portion of each system, information is presented regarding the firing treatment required to develop stabilized cubic ZrO2. A list of suggestions for further study of these systems, to further delineate the characteristics required for possible commercial utilization, is presented.

Jan 1, 1982

By L. Y. Sadler

This report summarizes the findings of a 9-yr research program, sponsored by the U.S. Department of Energy and conducted by the Bureau of Mines, to evaluate refractory liner materials for coal gasifier reactors. Commercially available refractories were exposed to coal gasifier reactor environments, reproduced in the laboratory with a high-temperature, high-pressure test facility, followed by extensive postexposure evaluation. Thirty-six castable or gunnable refractories and cements and 24 refractory brick were evaluated. The behavior of castable refractories reinforced with stainless steel fibers was also examined. Gas environments that were evaluated included steam, H2, CO2, CO, and typical high-and low-Btu gas mixtures. Exposure pressures ranged from 100 to 1,000 psig, temperatures from 5000 to 1,1000 C, for periods from 50 h to 2,000 h. In some exposures, sodium and/or potassium hydroxide were introduced in order to simulate a high-alkali environment. It was found that intermediate-and low-alumina refractories produced from domestically available raw materials, rather than high-alumina refractories produced from imported raw materials, gave the best service as liner materials and that alkali attack was probably not a serious problem with most refractories. Based on the results of this program, good choices of refractory liner materials for gasifier reactors can be made.

Jan 1, 1984

This document is Volume II of a two-volume report on underground and surface metal and nonmetal mine fires occurring between 1950 and 1979. Two surface fires from 1980 are included. Volume I discusses the methods of data acquisition, data analysis procedures, and results and conclusions. This volume contains (1) a master list of all fire incidents obtained from MSHA reports, (2) an annotated bibliography of all MSHA reports, journal articles on selected incidents, and non-reportable fires (appendix), and (3) indexes to be used in accessing incidents in the master list and annotated bibliography. These three types of information provide the reader with a complete summary of metal and nonmetal mine fires during the period from 1950 through 1979 and a convenient means to locate incidents of specific interest. The body of this volume is organized around two tables and a series of indexes. The two tables are master lists of underground and surface fire incidents. They are followed by 15 indexes keyed to the master list and annotated bibliography. The Appendix contains three different parts: ? The annotated bibliography of MSHA fire reports (one section each for underground and surface mine fires). ? The annotated bibliography of journal and other periodical articles about selected fires from the MSHA bibliography. ? A listing of non-reportable fires (one section each for underground and surface mine fires). Descriptions of the contents and use of each of the three major components of this volume (i.e., master list, indexes, and appendix) are presented in Section 2.0.

Jan 1, 1980