Search Documents

By Anatol Wojtowicz

This research program was conducted to determine if respirable coal dust emanating from a continuous mining machine can be suppressed more effectively by a high expansion foam than by the water sprays conventionally used. A high expansion foam system was developed and tested on a continuous mining machine under actual operating conditions. The utility of the system was demonstrated. Test results tend to show that foam application is more effective than water sprays in suppressing respirable coal dust. However, because of the extreme variability of the test conditions, scatter in the sampling data, and other factors, not enough data was obtained to form a firm conclusion that foam is more efficient than a water spray in suppressing respirable coal dust. Sufficient statistical data was obtained, however, to indicate that foam is more efficient than water in suppressing total float coal dust.

Jan 1, 1974

By Lloyd A. Morley

A guide to the development and use of an APL computer program for the analysis of load-flow problems is presented. The program is designed to provide an interactive method of load-flow study to improve underground coal mine electrical system design and safety. The theoretical basis for load-flow analysis is discussed, along with per-unit calculations which facilitate computation. Specific input/output, execution and network modification procedures are presented for using the APL program. In addition, typical results are given for examples taken from power system analysis literature.

Jan 1, 1977

By Joan Weinberg

Real gross national product (GNP) grew at a seasonally adjusted annual rate of 2.2% in the third quarter, down from a revised 3.0% in the second quarter, according to preliminary data from the U.S. Department of Commerce (table 1). The slowdown in the rate of growth was attributed to the summer drought, a larger trade deficit, and a decline in Federal spending for defense. Exports slowed from the second quarter, as the dollar, compared with other industrial country currencies, edged up. Imports of both consumer goods and capital goods rose sharply, with consumers buying more foreign cars, computers, and electrical machinery. Although net exports of goods and services deteriorated slightly from the second quarter, the U.S. trade position continues to be much improved from 1987 and first quarter, 1988. Business spending for new plant and equipment rose at a 4.6% pace, well below that recorded earlier in the year. The 3.5% increase in consumer expenditure was accounted for mainly by nondurable goods and services; expenditure for durable goods--those products lasting more than 3 years--rose only 0.4%. Inflation, as measured by the fixed-weighted GNP price index, rose at an annual rate of 4.9% in the third quarter. Prices rose slightly less than they had in the second quarter, when inflation reached a 6-year high. In September, 1988, the President signed a U.S.-Canada free trade agreement (FTA) which will eliminate all tariffs and most nontariff barriers between the two countries by 1999, thereby creating the world's largest open market. In 1987, U.S.-Canadian bilateral trade totaled $161 billion. The expansion of trade is expected to generate 5% higher growth for Canada and up to 1 % higher growth for the United States by the end of the century. The higher growth for the United States translates into an estimated 750,000 jobs, and $2.4 billion in exports. Canadian parliamentary approval of the agreement is still required before the treaty can take effect. The debate in Parliament is continuing, and the issue is not expected to be resolved until after the November 21 election.

Jan 1, 1988

By John H. Soulé

"INTRODUCTION The Mining Branch of the Bureau of Mines has used the wagon drill to sample mineral deposits in New Mexico. This method of sampling was successful and con¬stituted an important phase of the work on five exploratory projects undertaken in 1943, 1944, and 1945. The deposits varied in topographic features, geology, mineral content, and in the physical characteristics of the rocks drilled. The altitudes ranged from 630 to 7,800 feet. Three hundred and seventeen holes totaling 6,852 feet were drilled. The deepest hole was 66 feet; the average depth was a little less than 22 feet.The results of the above-mentioned work form the basis of this report. Special attention is given to the later and more improved techniques used. This report was written with the expectation that the procedures might prove advantageous to others in the exploration and sampling of near-surface mineral de¬posits, and that a more extended use of the technique might result.AcknowledgmentsAcknowledgment is due Charles H. Johnson, chief of the Rolla Division, Mining Branch, for helpful suggestions in starting this work, and to J. H. Hedges, chief of the Tucson Division, Mining Branch, W. R. Storms, engineer-in-charge of the Silver City, N. Mex., Field Office, and Donald H. Mullen, mining engineer attached to that office, for assistance in preparing and editing this report."

May 1, 1947

By McHenry Mosier

This is the fourth progress report in the series on the use of detachable rock-drill bits in the metal mines of the United States. It contains comparative statistics and costs or drilling at eight mines not reviewed in previous reports, comparison of the use of detachable bits at small mines and large mines, a discussion on the life of drill rods, and general conclusions derived from an analysis of the rock-drilling practice at all the mines investigated on this survey. This paper completes the descriptions of operating practice in rock drilling at individual mines. Data on drilling practices at 28 mines are given in appendices I and II and drilling costs are shown in appendix III. Research in the fundamentals of rock drilling, including the use of detachable bits, has been undertaken by the Bureau of Mines in its testing adit at Mount Weather, Va. Reports on the progress off this investigation will be issued when results warrant their publication.

Jan 1, 1937

By J. Fletcher Smoak

Consumption of abrasive materials in the United States in 1981 was approximately $340 million, of which 37 % was industrial diamond (natural and synthetic), 39% manufactured abrasives, and 24% natural abrasives. Production and shipments of natural abrasives, excluding emery and industrial diamond, decreased in quantity 9% and 7%, respectively, when compared with that of 1980. Emery showed the largest change in output, decreasing 30% in quantity and 20% in value. Production of nonmetallic .manufactured abrasives material plus shipments of metallic abrasives material decreased 5% in quantity but increased 4% in value. Nonmetallic manufactured abrasives consisted of aluminum oxide (fused) and crude silicon carbide produced in the United States and Canada and accounted for 63% of the value of all manufactured abrasives. Metallic abrasives shipments included chilled and annealed iron shot and grit, steel shot and grit, plus cut wire, aluminum, and stainless steel shot and equaled 37 % of the value of all manufactured abrasives.

Jan 1, 1982

By C. T. Baroch

The purpose of this report is to describe the design features and techniques used in operating a plant capable of producing about 1,500 pounds of titanium metal per day. The process used was based on the reduction of titanium tetrachloride with magnesium, a modification of what is generally known and spoken of as the Kroll process. Sponge metal crushed to melter's specifications was the end product of the operation as conducted. The report is divided into sections covering general plant layout and the major unit operations. These, in turn, are each divided into discussions of the equipment, operating procedures, and typical results. Descriptions are given in more detail than is generally expected of a technical report. During 1953 and 1954 over 130 engineers and businessmen, officially representing some 80 industrial, chemical, end engineering firms, visited the operating plant, and their questions, which indicated a serious interest in details, have served as a guide for the material contained in this report.

Jan 1, 1955

By Thomas M. Barczak, Joe Bower, Jinsheng Chen

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water-to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water-solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

By Robert S. Schechter

A minitest of the new potassium chloride-potassium carbonate two-stage in-situ uranium leach process has been carried out at the Intercontinental Energy Corporation (IEC) Zamzow project site in South Texas. Substantial quantities of high concentration uranium were produced indicating the viability of the leach solution. The test results yield information regarding the reservoir dispersivity, the average cation-exchange capacity of the formation, and the distribution coefficients describing cation-exchange reactions. The test also indicates permeability anisotropy and the existence of disturbed flow fields.

Jan 1, 1985

By G. H. West, R. L. Sebastian, W. A. Darror

"This bibliography was compiled in the course of research work by the Bureau of Mines on the utilization of magnesites in the West. The results of the research will appear as a bulletin of the Bureau.1. ANALYTICAL METHODS. 11 Knight, X. and Wheeler, W.H. Proc. Iowa Acad. Sci., 13, 1907, 167 (C.A.1, 1370). Describes experience in analysing calcite and dolomite. Reports great excess of oxalate unnecessary and separation of sulphates by alcohol is best.2 Meyerhofer, J. Zeit, Angew. Chem., 21, 1908, 592. Direct determination of Mg as phosphate after removal of SiC2, by keeping R203 in solution with ammonium citrate.3 Merckschen Guano Phosphat Werke. Chem. Ztg., 33, 1909, 545 (C.A. 3, 2281). volumetric analytical methods.4 Popel, M. Zeit. Angew. Chem., 21, 1908. 2082 (C.A, 6, 412). Determination of CaO in presence of CaC03.5 Blasdale, W.C. Jour. Am. Chem. Soc., 31, 1909, 91? (C.A. 3, 2658). Studies of separation of Ca from Mg.6 Hundeshrgen, F. Zeit. Offent. Chem., 15, 1909, 85 (C.A. 3, 1853). Valua¬tion of caustic magnesia by analysis. Volumetric methods.7 Frerichs, H. and Krosberg, W. Apoth. Zeit., 24, 1909. 679 (C.A. 3, 2996). Tecting magnesia alba for Fe.8 Schoorl, N. Zeit. Anal, Chem., 48, 1009, 593 (C.A. 4, 5E9). Microchemical tests for Mg, Li, K. and Na.9 Heyer. Chew. 2Ag., 33, 1009, 1157 (C.A. 4, 1588). Determination of CaO in presence of CaCO3. CaCO3 in soluble in cold neutral solution of NH3 salts. Solubility Is diminished by free NH4OH."

Oct 1, 1923

The investigations reported herein comprise preliminary studies to evaluate large scale mining systems adaptable to the thicker oil shale deposits in the deeper central portion of the Piceance Creek Basin. The studies include an evaluation of the geology, hydrology and resources of the Basin., evaluation of a potential prototype mine site, synthesis of rock mechanics data on Green River Formation oil shale, selection and preliminary design and cost evaluation of six potential mining systems and a ranking analysis to aid in selecting the most promising system. Results of the ranking analysis indicate the following four systems to be most promising for large scale underground oil shale mining: - Chamber and pillar (using spent shale backfill) - Sublevel stoping with spent shale backfill - Sublevel stoping with full subsidence - Block caving with LHD's Recommendations for phase II are to investigate the above systems in greater detail, refine present cost data, and perform economic evaluations of oil shale mining using these systems.

Jan 1, 1975

By Naoki Hosoya, Setsuo Maeda

This paper addresses establishment of an experimental system for measuring biodynamic response (BR) of hand-arm system at the NIIH in Japan. BR measurement system at the NIIH is nearly equivalent to NIOSH installed system. The feasibility of the system is examined through the apparent mass (AM) measurement of the empty handle and a set of calibration masses. Apparatus The grip force was measured by using the handle shown in Fig. 1. The handle has two force sensors (KISTLER, 9212) and one accelerometer (PCB, 356A12). A low-pass filter with 5 Hz cut-off frequency was used to the grip force from measured force signal. Figure 2 shows BR measurement system in this study. The push or pull force at the handle was measured by using the force plate (KISTLER, 9286AA). The grip force and the push / pull force were displayed on a monitor. The shaker (IMV, VE-100S) is used to vibrate the hand-arm system along the forearm axis (Zh direction) (ISO 10068, 1998; ISO 5349-1, 2001). In most situations force actions for operating tools are expressed by grip, push, pull and combined these actions. These actions can be simulated in the test system. AM was obtained by performing H1 estimator in the PULSETM system (B&K, 3109) and it is denoted at the one-third octave band center frequencies. [ ] Methods In order to investigate the reliability of the system, AM measurement of the handle was performed. It is assumed that the handle is rigid in the upper limit of adoptive frequency range in this study. This assumption is validated in AM measurement of the empty handle. A pseudo-random vibration in the frequency range of 10 to 1,250 Hz was used and its amplitude is 1.0 (m/s2)2/Hz with a flat power spectral density (PSD) in the experiment. Measured AM includes the mass effect of the measuring cap in a subject experiment. Compensated apparent mass AMc(?) is obtained by Eq. (1) 1-2.

Jan 6, 2006

The State of Washington has a federal program that gives the Office of Surface Mining responsibility for assuring the reclamation of lands affected by coal mining. Most of Washington's coal-bearing regions lie west of the Cascade Mountains. The state's coal reserves are estimated at 1.4 billion tons, about 0.3 percent of the nation's total coal reserve. Steeply dipping. minable seams range from 2.5 to 25 feet in thickness. The occurrence of coal in Washington has been documented since the early days of its settlement; at one time, coal production played a significant role in the state's economy. During the late 1800s and early 1900s, coal was second only to lumber in Washington's industrial production. Coal production declined as other sources of energy were developed. By 1959, production was at 200,000 tons. Regulation of the coal mine operations in Washington is conducted by the Office of Surface Mining's Casper, Wyoming, Field Office and its local office in Olympia, Washington. All permit applications and abandoned mine land reclamation are completed by the OSM Western Support Center in Denver, Colorado. Inspections of mine and reclamation sites are conducted by OSM reclamation specialists located in Olympia.

Jan 1, 1992

By E. K. Stanek

This report contains the results of an investigation into the feasibility of periodically measuring parameters of the insulation for a mine electrical power system in order to detect incipient faults. The variety of insulation parameters evaluated included insulation resistance, dissipation factor, power factor (vs. applied voltage), current harmonics, leakage current, infrared radiation, as well as certain circuit breaker parameters and tests. In order to augment field tests a program of accelerated life testing was also carried out. Apparent inconsistencies in data were identified as the result of environmental effects, primarily temperature and relative humidity. A series of environmental tests were conducted to develop correction factors that allow one to refer measured parameters to standard conditions. A portable data collector was develop-ed to aid in the accurate collection and analysis of laboratory and field data. The primary conclusion is that insulation deterioration can be measured and failure predicted with reasonable confidence. The secondary conclusion is that most of the tests are impractical in the field although useful in the laboratory. Infrared sensing, insulation resistance and dissipation factor are the best insulation field tests when portability is taken into account.

Jan 1, 1979

By Sean Gallagher, William S. Marras, Alan S. Litsky, Deborah Burr

This paper describes a comparison of the fatigue failure responses of older versus younger lumbar spine cadaver motion segment specimens. These specimens were repeatedly subjected to loads simulating those experienced by the spine in lifting a 9 kg load in different torso flexion postures (0, 22.5, and 45 degrees of flexion). An older sample of 36 motion segments (average age 81 years + 8 SD) is compared with a younger sample of 18 motion segments (average age: 47 years + 9 SD) with respect to the number of cycles to failure and results of survival analyses evaluating the effects of flexion and bone mineral content with and without the younger data set. Compared to the older sample of spines, the younger sample exhibited many more cycles to fatigue failure in all the torso flexion conditions (10020 versus 8267 average cycles to failure in 0 degrees flexion, 7124 versus 3262 in 22.5 degrees flexion, and 3229 versus 263 cycles to failure in 45 degrees flexion). The increased cycles to failure in young specimens is likely due to the increased bone mineral content (BMC) in younger motion segments (30.7 g + 11.1 g per motion segment versus 27.8 + 9.4 g). Cox regression analyses modeling both flexion effects and BMC indicate that betas are similar when just older spines are modeled and when younger specimens are included in the analysis. Betas for survival analysis models with and without younger specimens generally show little change for flexion (2.716 versus 2.756 for 22.5 degrees [0 degrees referent], 3.926 versus 3.380 for 45 degrees [0 degrees referent]). Bone mineral content shows a similar protective effect in both models (Betas: -0.127 versus -0.087). Overall, comparison of the models indicate that risk ratios are similar for 22.5 degrees flexion, slightly increased for 45 degrees flexion and slightly more protective influence predicted for BMC in the combined sample versus the older sample alone.

By H. W. St. Clair

This study was undertaken to provide a more adequate knowledge of the chemistry of the sulfide volatilization process for recovery of tin from low-grade Bolivian ores. The investigation was partly supported by the Department of State under its program for scientific cooperation with South American republics. The results of this investigation demonstrate the conditions under which cassiterite (Sn02) may be converted to stannous sulfide by reaction with pyrite or sulfur vapor, Quantitative data are given on the rate of sulfidization and on the vapor pressure of stannous sulfide.

Jan 1, 1954

By Kristine M. Krajnak

Occupational exposure to hand-arm vibration through the use of powered hand tools can result in reductions in tactile sensitivity, grip strength and manual dexterity. In fact, even acute exposures to vibration cause shifts in vibrotactile thresholds in exposed fingers (2,4,5). Although reductions in tactile sensitivity after acute vibration exposures are transient, cellular changes associated with this shift in sensitivity could lead to the more permanent reductions in tactile sensitivity that are a common symptom of hand-arm vibration syndrome (HAVS). Methods Animals. Male Sprague Dawley rats (6 weeks of age) were used for all experiments. Animals were housed in AAALAC accredited facilities, and all procedures were approved by the NIOSH Animal Care and Use Committee and were in compliance with the CDC guideline for care and use of laboratory animals. Vibration exposures were performed by restraining rats in a Broome-style restrainer, and securing their tails to the vibration platform using 6 mm wide straps that were placed over the tail every 3 cm. Restraint control animals were treated in an identical manner except that the tail platform was set on isolation blocks instead of a shaker. Tail temperature and current perception thresholds (CPTs). Rats were exposed to 4 h of tail vibration (125 Hz, 49 m/s2), or restraint. Tail temperature was collected prior to and immediately following the exposure using an infra-red camera. Sensory neuron function was assessed by measuring CPTs with a Neurometer (Neurotron, Baltimore, MD). Transcutaneous nerve stimulation was applied to the C10 region of the tail. Three frequencies were used to test specific fiber types (5 Hz – C, 250 Hz - Ad, and 2000 Hz – Aß). The intensity of the stimulus was automatically increased in small increments until the rat flicked its tail. Tests at each frequency were repeated until the animals displayed 2 responses that were within 2 CPT (or 0.02 mA) of each other (2-4 tests/animal). CPT tests were performed prior to the exposure, immediately following the exposure, and 24 h after the exposure. Data Analyses. Temperatures were analyzed using a one-way ANOVA with animal as a random variable. ANCOVAS were used to analyze the CPTs at each frequency. Temperature at the time of the CPT test was used as a covariate, and animal was used as a random variable Results Tail temperatures declined between pre and post exposure (F(1,25) = 62.85, p < 0.001; mean ± sem pre 25.96°C ± 0.42, post 20.71°C ± 0.77), but were back to baseline levels by 24 h after the exposure in both groups of rats. The ANCOVAs demonstrated that exposure to a single bout of vibration did not alter sensitivity of C (5Hz) or Ad (250 Hz) fibers to stimulation.

Jan 6, 2006

By Joseph Gersic

The U.S. Bureau of Mines assessed mineral resources of the BLM Malheur-Jordan Resource Areas (MJRAs) in southeastern Oregon in 1993 and 1994. The study relied heavily on acquiring and analyzing existing data. In order to efficiently handle and analyze a large quantity of data, a minerals information management program, informally called MINFO, was developed as a frontend for three databases created to store basic information gathered during the minerals resource assessment. The MINFO program will also provide the BLM with a method of tracking and updating minerals information in the future because program modules in MINFO allow the addition of new data and the correction of errors, creation of print files, transfer of data to other database formats, exportation of data to other software packages, and creation of AutoCAD script files to be used in conjunction with AutoCAD to produce maps. The report specifically identifies significant past and present mineral exploration and development activities and possible areas of future mineral exploration and development. These areas are informally designated as areas of development interest or ADIs. The report contains a scenario of what mineral development might reasonably occur in the foreseeable future if the BLM does not substantially change its present resource management plan, and it shows the possible socioeconomic impacts of that development. The uncertainty of the political and economic situation makes it extremely challenging for the USBM to accurately predict a reasonably foreseeable development scenario. The reasonably foreseeable development (RFD) scenario developed by the USBM for the BLM indicates short-term RFD of minerals should have a negligible socioeconomic impact, and longer-term RFD of minerals should have a slight socioeconomic impact on the MJRAs. The mining industry is facing a rapidly changing business and regulatory environment in Oregon. Several signal changes have occurred recently, including State regulations that require significant bonding prior to the startup of "chemical process" mining, an initiative by a special interest group to stop all chemical process gold mining within the State, and an opinion by the Oregon Attorney General (AG) banning all forms of placer mining without exemption. In the AG opinion, not even gold panning is allowed, and the prohibition applies to mining claims on Federal lands. The State legislature may amend the statute to allow small scale placer mining to occur, as was allowed under an AG opinion issued in 1982. These and other changes occurring at the local, State, and National levels are making it more challenging for the mining industry to operate in the United States. Several epithermal gold properties in the MJRAs attracted the mining industry&apos;s interest. Only the Grassy Mountain Project of Newmont Grassy Mountain Corporation may be developed in the next few years. It is probable that at least two other properties will be developed if Grassy Mountain is successful. Mining companies are waiting to see the effect recently promulgated State mining regulations and more stringent proposed regulations, particularly bonding regulations, may have on Grassy Mountain. Resources of bentonite, diatomite, and zeolite are abundant. The almost Ubiquitous stone, sand and gravel, and semiprecious gemstone resources also were examined. Little environmental or socioeconomic impact is expected from reasonably foreseeable development of these mineral resources.

Jan 1, 1994

By Theodore L. Turner, Joseph H. Swift

A study on a small laboratory scale was made of the use of ammoniacalammonium carbonate for batch leaching Mn from low- grade manganiferous materials ( 6 to 16 pct Mn) obtained from deposits in the southern district of Aroostook County , Maine . These materials were partially reduced at 500 ° to 700 ° C with H₂ or CO and then leached with solutions of NH and CO₂ dissolved in water . Extraction of 80 to 90 pct of the Mn was obtained from some sample materials , but 10 to 34 pct of the iron was also extracted . Material from the Littleton Ridge deposit contained manganese intimately associated with Fe , a condition which contributed to difficulties in obtaining a commercially acceptable product . Extensive investigations of the leach and reduction processes with various mixtures of H₂ and water vapor , and CO and CO₂ , failed to disclose a set of conditions for selectively leaching the manganese . Finely divided metallic Fe was probably produced during the reduction steps so that Fe was leached with the Mn in the subsequent extractions .

Jan 1, 1964

By Sean Gallagher

Background. There is currently little information regarding factors associated with specific modes of motion segment failure using a fatigue failure model. Methods. Thirty-six human lumbar motion segments were fatigue tested using spinal compressive and shear loads that simulated lifting a 9 kg weight in three torso flexion angles (0°, 22.5°, and 45°). Twenty-five segments failed via fatigue prior to the 10,000 cycle maximum. These specimens were visually inspected and dissected so that the mode(s) of failure could be determined. Failure modes included endplate fractures (classified into nine varieties), vertebral body fractures, and/or zygapophysial joint disruption. Logistic regression analyses were performed to determine whether certain morphometric variables, amount of motion segment flexion, disk degeneration scores, and/or loading characteristics were associated with the occurrence of specific failure modes. Findings. Results indicated that stellate endplate fractures were associated with increased posterior shear forces (P < 0.05) and less degenerated discs (P < 0.01). Fractures running laterally across the endplate were associated with motion segments having larger volumes (P < 0.01). Endplate depression was more common in smaller specimens (P < 0.01), as well as those experiencing increased posterior shear force (P < 0.05). Zygapophysial joint damage was more likely to occur in a neutral posture (P < 0.01). Interpretation. These results suggest that prediction of failure modes (e.g., specific endplate fracture patterns) may be possible (at least for older specimens) given knowledge of the spinal loads along with certain characteristics of the lumbar spine. Published by Elsevier Ltd. Keywords: Lumbar spine; Endplate fractures; Zygapophysial joints; Morphometry; Disk degeneration; Motion segments; Aging

Jan 1, 2006