Search Documents

By R. V. Ramani, W. Miola

"A relationship exists between the quartz contents in the underground coal nine airborne dust samples and those in the coal and host rocks that are mined [17, 18, 19] The prescribed method for quartz analysis in respirable airborne coal dust samples is the MSHA P-7 method. Accurate quartz analysis procedures are needed for bulk samples in order to predict the potential quartz content in airborne nine dust, which in turn will aid the design of quartz dust control procedures during mining. thereby reducing the airborne quartz dust in underground atmospheres. The requirements of this method are that the amount of quartz is the sample be less than 250ug, and the total sample weight less than 2,500 ug. Unlike with airborne dust samples, there are no limitations to the available mass of bulk samples. However, these are no standard procedures for the preparation of bulk samples for scanning or prescribed methods for quartz analysis. The NIOSH and MSHA methods are certified for roped* dust and the acceptance of these methods for bulk samples assumes that the bulk samples will be reduced to the conditions specified for respirable dust samples. An alternative method is X-ray diffraction, which provides higher average quartz values than those obtained from P-7 method for the same samples.An investigation was carried out to determine the optimal procedure for preparing the bulk samples for the IR and XRD analyses. In this paper, the investigations on the effects of calibration, particle sizes, matrix composition, interferrous, and behavior of the filter substances on IR, XRD and FTIR results are presented. The error introduced by the presence of kaolinite and a new sample asking procedure to reduce it are discussed. The problems experienced with conventional sample holders for scanning were eliminated with the design and development of a new hollow sample holder. Quantitative comparison of quartz determinations by IR, XRD and MR methods on coal, roof and floor rocks, and airborne dust samples are presented. The important factors affecting the results of quartz analysis methods are: 1) bulk sample preparation for obtaining representative and homogeneous analysis samples: 2) particle size distributions of the analysis samples and calibration standards; 3) qualitative matrix composition of the analysis sample; 4) matching calibration standards to analysis sample; 5) substrates for sample deposition during analysis sample preparation; 6) procedures for analysis sample mounting; 7) selection of proper portions of she response profile for insanity measurement; and 8) interferences of spurious phases with the critical analyses. The recommendations of this study are important to enable comparisons and interpretations of analysis and research results."

Nov 1, 1995

By G. W. Jones

Fires in anthracite refuse banks are troublesome and may become exceedingly costly to combat. Instances are known in which refuse-bank fires have grown to such magnitude that entire mining properties have been endangered. In one instance4/ a refuse-bank fire cost the mine management several hundred thousand dollars to extinguish. The exact number of fires formerly existing or now active in the anthracite region of Pennsylvania is not known. There are hundreds of anthracite refuse banks in this region, some very high and large in area, that have never caught firs, although a few are over 50 years old. This would indicate that spontaneous ignition of the material in these banks is improbable, a conclusion confirmed by recent laboratory research.

Jan 1, 1939

By G. W. Jones

Fires in anthracite refuse banks are troublesome and may become exceedingly costly to combat. Instances are known in which refuse-bank fires have grown to such magnitude that entire mining properties have been endangered. In one instance4/ a refuse-bank fire cost the mine management several hundred thousand dollars to extinguish. The exact number of fires formerly existing or now active in the anthracite region of Pennsylvania is not known, There are hundreds of anthracite refuse banks in this region, some very high and large in area, that have never caught fire, although a few are over 50 years old. This would indicate that spontaneous ignition of the material in these banks is improbable, a conclusion confirmed by recent laboratory research.

Jan 1, 1939

By J. B. Carman

This paper, describing the mining practices and methods at the mine of the Molyb¬denum Corporation of America, is one of a series of similar papers on mining methods in the various mines of the United States being prepared by the Bureau of Mines. The mine of the Molybdenum Corporation of America is in the Red River mining dis¬trict, Taos County, northern New Mexico (fig. 1), The mill and camp are in the valley of Red River, about 7 miles east of the town of Questa; the mine is 1 ¼ miles away, in Sulphur Gulch, a tributary of Red River. The mine is about 600 feet higher than the mill, at an altitude of about 8,700 feet. The climate is cold in winter, but does not interfere serious¬ly with continuous operation. The mine normally produces about 40 tons of sulphide molybde¬num ore per day, which is concentrated at the local mill and chipped to the plant of the Molybdenum Corporation at Washington, Pa.; there it is made into either ferromelybdenum or "molyte" (calcium molybdate), for use in alloys. The ore is mined from narrow, irregular veins by the cut-and-fill method. About 65 men are normally employed underground and on the surface at the mine.

Jan 1, 1931

By James C. Cawley

The Bureau of Mines conducted an investigation to statistically determine the mean current or voltage for resistive, inductive, and capaci-tive circuits that would cause spark ignitions in 8.3% methane-air, 5.3% propane-air, and 7.8% ethylene-air mixtures. Each mean ignition current or voltage was determined on the basis of 100 trials. Each trial consisted of 400 revolutions, 200 in each polarity, at 80 rpm of the standard breakf1ash apparatus. In general, spark ignition curves published in UL 913 for resistive and inductive circuits represent approximately the mean current values determined in this study, while published capacitive circuit values in methane are considerably less than the mean voltage values from this study, especially for a capacitance of less than 100 ~F. For resistive and inductive circuits, spark ignitions were obtained at currents con-siderably below those in the published curves, but this study was not optimized to find minimum ignition values. This report defines "safety factor" as applied to intrinsic safety testing as the energy ratio of the mean values of ignition current or voltage for two test gases. The safety factors presented in this report are not constant with voltage or current and, therefore, are not recommended for use.

Jan 1, 1986

By Robert A. Cummings

A rock mass classification system has been developed for recommending drift support requirements in block caving mines. This development follows a two-year program incorporating field observations of support practice and performance in rocks of different classes, at several U. S. block caving mines. Popular rock mass classification systems presently in use for tunneling were applied at the various field sites; and were evaluated for conformance with caving mine support requirements and for general utility to caving mine operations. The developed system (MBR System) accepts readily-obtainable engineering and geologic data to yield a rational estimate of support requirements. The background and development of the MBR system is described in this report (Volume I). The use of the system is given in the Manual, a separate volume (Volume II).

Jan 1, 1984

By David Bendersky

This report covers the activities of a feasibility study of fiber optics technology fur use in mines. The objective of the study was to evaluate, both technically and cost-wise, the possible use of fiber optic technology for underground mine communication and monitoring systems. The first phase of the study was devoted to the collection of information on the present underground mine communication systems and monitoring techniques, and the status of applicable fiber optic technology. In the second ph se of the study, a communication and monitoring system for a hypothetical underground coal mine was designed and the costs estimated. The significant findings and conclusions are presented.

Jan 1, 1982

By Philip E. Niebuhr

A procedure, which can be performed in the field by nonanalytical personnel, is given for sensitive spot tests for detecting tellurium or selenium. The expressed need of a field test for detecting small amounts of tellurium, which may be accompanied by relatively large amounts of selenium, has led to the development of this method. Tellurium search has been impeded by the lack of a satisfactory test from the standpoint of sensitivity and specificity. A quantitative laboratory method exists, but it is expensive and relatively laborious. Several other qualitative tests are known, but they require unstable solutions, which must be freshly prepared for use, and a greater variety of laboratory equipment. The particular advantages of the test described are its simplicity and the stability of the reagents required, there-fore is is well adapted for field use. Also, this test was found to be of practical use in the analytical laboratory when screening samples, thereby reducing analytical costs. The roughly quantitative interpretation of the results can save time by indicating the approximate size of the sample taken for a quantitative determination.

Jan 1, 1962

By C. Thomas Hillman

The practical concern of economic minability of large, high-grade manganese nodule deposits in the northeast Pacific Ocean is addressed in this Bureau of Mines report. Principal objectives are to (1) estimate tonnage and grade of deposits with significant potential and (2) describe and estimate profitability of operations designed to mine and process deposits with greatest apparent potential. Analysis of data from over 800 ship stations identified three areas for detailed study. Average metal contents of these areas range from 1.30 to 1.45 wt pet nickel, 1.00 to 1.24 wt pct copper, 0.21 to 0.26 wt pct cobalt, and 26.8 to 27.8 wt pct manganese. Estimated recoverable nodule resources are 67.0, 66.9, and 148.8 million dry metric tons (t). A system to mine, transport, and process nodules from the three sites is described and costed. Although hypothetical, the system utilizes hydraulic mining and Cuprion (Kennecott) processing, which have been successfully tested at pilot scale. Nickel, copper, and cobalt are the three primary products, but ferromanganese is a considered option. Estimated capital requirements are approximately $1.5 to $1.7 billion for three-metal production. If ferromanganese were recovered, an additional investment of about $130 million would be required. Operating costs range from $71 to $83 per dry metric ton of nodules without manganese, and from $103 to $123 per dry metric ton with ferromanganese. Discounted cash flow analyses predict low returns, ranging from 2.7 to 5.2 pct with ferromanganese and from 4.1 to 6.0 pct without.

Jan 1, 1983

By G. S. Rice

The Experimental Mine of the United States Bureau of Mines is a unique coal mine that serves as a large-scale testing laboratory. It is used primarily for testing the explosibility of coal-dust and gases but is also the workshop for many other kinds of research work of which the chief object is to increase safety in mining. The mine is situated in Allegheny County, Pa., about 13 miles southwest of Pittsburgh among the high hills of the west bank of the Monongahela River, at the northeastern edge of the gas-coal district of the Pittsburgh coal bed which extends south through the Connellsville coking-coal district into West Virginia. The Pittsburgh bed, of the Upper Carboniferous age, is one of the most extensive continuous coal beds in the United States, if not in the world. Throughout large areas it shows remarkable uniformity of thickness, levelness, and character of coal, which is a coking coal of high-grade bituminous rank. Its thickness in the northern part is 5 to 5 ½ feet and in the central and southern part is 7 to 9 feet.

Jan 1, 1933

By James L. Hendrix

The applicability of a rotating drum with an attached trommel as a flocculation dewatering device of Florida phosphatic claywastes was studied. Several experiments were conducted in order to determine the important fabrication and operating parameters. Results from the experiments indicated flint the dosage of polyethylene oxide required to form a satisfactory product cake could be reduced by using the rotary drum, which introduces less shear stress into the fluid than a constant stirred tank mixer. It was found that the length of the mixer was the most important parameter. Increased length increased the retention time the flocs stayed in the mixer without dewatering. Such increased time decreased the stability of the flocs. Through analysis of residence time distribution data it was found that the longer mixers approached plug flow characteristics. Other important parameters were trommel length and rotational speed. Mixers from 10 cm diameter to 35.6 cm diameter were tested with good results.

Jan 1, 1982

By L. R. Herrmann

The most fundamental feature of fracture is that it involves separation. Such separation can arise by either separation of molecules, more or less along the line joining their centers (tension), or by d sliding separation roughly perpendicular to that line (shear). Theoretically, a perfect crystal could never be broken by the application of perfectly axial compressive stress (until some sub-molecular actions occur). In tension fields the calculated forces between molecules are extremely high. Consequently, calculations based on the forces known to exist in materials at the molecular and crystalline levels always lead to strengths which are two or three magnitudes higher than the strengths obtained in service or in the laboratory. It has been a major problem, therefore, to explain: (a) How fracture can occur in compressive stress states. (b) Why the observed strength of a material is always much lower than its calculated strength.

Jan 1, 2012

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

By James Paone

This report on the state of the art of horizontal boring technology for underground power transmission installations was prepared by the Bureau of Mines at the request of the Department of the Interior. This paper describes the different machines and methods used in augering, impacting, pushing, drilling, and machine tunneling horizontal holes through soil and rock. A review of the borehole survey and guidance tools and techniques applicable to these methods is also given. Nonboring methods used for emplacement of power distribution and transmission lines are briefly discussed. The paper ends with a brief technical forecast, an analytical summary of the state of the art, and recommendations based on power industry needs. Horizontal boring techniques for power distribution lines installation are adequate to meet the requirements of the power industry, particularly where such burial involves relatively short distances in soil or soft rock. For burying power transmission lines, particularly in the harder rocks and over relatively long distances, horizontal boring methods are not as well advanced. Research and development as well as economic incentives to equipment manufacturers could substantially improve the state of the art. Obstacle detection and guidance systems for directing boreholes to specified targets need major improvements to meet the requirements of the power industry for underground burial of distribution and transmission lines

Jan 1, 1968

By Thomas W. Camm

This study was done to evaluate the costs of various dumping operations at waste and spoil piles. It has been theorized that accidents associated with dumping operations might be reduced by short-dumping rather than edge-dumping, but many operators have been reluctant to use short-dumping because they believe it is not as cost effective as edge-dumping. To evaluate this perception, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health reviewed the costs of various dumping methods at waste and spoil piles. The study found that overall cost differences between the two methods were not significant in most cases. However, while overall cost differences between the two methods appear small, capital costs could be more significant when short-dumping if numerous dump sites are used concurrently. The choice of which method to use should be based on considerations of the safety of dozer and truck operators.

Jan 1, 2000

This report presents information developed during Bureau of Mines contract H0242016, "Mine Shaft Fire and Smoke Protection Systems" from May, 1974 through June, 1975. Purpose of the metal and nonmetal health and safety project was to evaluate mine shaft fire and smoke hazard problems, and to develop and demonstrate a low-cost, reliable mine shaft fire protection system that would protect against such hazards and would be applicable to a majority of metal and nonmetal mine shafts, including raises and winzes, especially in deep mines. Program effort proceeded through five phases, culminating in the successful in-mine fire demonstration of a prototype system. In addition to this final report, a film is available which depicts components of the system and its successful shaft fire testing at an underground mine.

Jan 1, 1975

By P. L. Woolf

Blast furnace coal injection tests conducted by the Bureau of Mines in cooperation with a consortium of 22 steel companies in 1963-1964 are described. These tests were part of a program of extensive investigation of auxiliary fuel injection in the Bureau's experimental blast furnace located at Bruceton, PA. Seventeen coal tests are described on various coals ranging from anthracite to subbituminous. Factors affecting maximum rates of injection were studied. These included coal size, coal type, and oxygen enrichment. The effect of high sulfur content coal and the means to control metal sulfur were investigated. An epilogue briefly describing the commercial experience with coal injection from 1960 to the present has been included.

Jan 1, 1985

By Steven A. Hawkins

This report details the conduct and results of a 5-month study to collect data on the use of steel support for ground control in European underground coal mines. The report summarizes European steel support design practices and describes the applicability of steel supports to U.S. mining conditions.

Jan 1, 1980

By Fred N. Kissell

This handbook describes effective methods for the control of methane gas in mines and tunnels. It assumes the reader is familiar with mining. The first chapter covers facts about methane important to mine safety, such as the explosibility of gas mixtures. The second chapter covers methane sampling, which is crucial because many methane explosions have been attributed to sampling deficiencies. Subsequent chapters describe methane control methods for different kinds of mines and mining equipment, primarily for U.S. coal mines. These coal mine chapters include continuous miners and longwalls, including bleeders. Coal seam degasification is covered extensively. Other coal mine chapters deal with methane emission forecasting and predicting the excess gas from troublesome geologic features like faults. Additional coal chapters contain methane controls for shaft sinking and shaft filling, for surface highwall mines, and for coal storage silos. Major coal mine explosion disasters have always involved the combustion of coal dust, originally triggered by methane. Thus, a chapter is included on making coal dust inert so it cannot explode. Methane is surprisingly common in metal and nonmetal mines around the world, as well as in many tunnels as they are excavated. Accordingly, a chapter is included on metal and nonmetal mines and another on tunnels. Proper ventilation plays the major role in keeping mines free of hazardous methane accumulations. The ventilation discussed in this handbook, except for the chapter on bleeder systems, deals only with so-called face ventilation, i.e., ventilation of the immediate working face area, not ventilation of the mine as a whole. The omission of whole-mine ventilation was necessary to keep this handbook to a reasonable size and because a huge amount of excellent information is available on the subject.2

Jan 1, 2006

By Mandius C. Lundal

This report describes the work done to develop a coal mining machine to increase productivity and recovery from thin seams beyond the highwall, in addition to decreasing the miner's susceptibility to to highwall hazards. First, radar transducers were adapted to measure coal thinkness and detect rock and coal interfaces; Then, the radar was incorporated into a cutterhead with steering controls. Next, visual displays were designed to show cutter position in the coal seam, and anticipated change In coal seam inclination. Finally, development of a telemetry system made remote control of the cutterhead possible. Simultaneously, a high-performance extended depth (HPxD) auger machine was designed with an automatic system to handle 600 ft of 36-in. diameter dual spiral flight conveyor sections. A two man crew controls all operations from a weather conditioned cab outside the VDZ, either at night or day time. As a primary mining tool, working 4000 hr/yr (2 shifts/day) recovering 60% of the coal 600 ft beyond the highwall, production to 500,000 ton/yr can be achieved. Volume II contains technical discussion of subsystems and machine drawings.

Jan 1, 1977