Search Documents

By Bill Birch, Toby White, Ian Brown

costs/benefits of electronic detonators and measure their effects on primary crusher productivity. 9 blasts (3 shock tube blasts, 6 electronic blasts). Measured electricity consumption & primary crusher throughput. Change to Electronic Detonators resulted in a 7% reduction in primary electricity costs and a 15% increase in primary crusher productivity.

Feb 1, 2020

By Douglas R. Burns

In New England, an area of the country where 3 ½" holes are considered large diameter,we are starting to experiment with 5" and 6" holes. The results are excellent in some areas and poor in others. The geology of rock is the major consideration to account for the blasting results.

Jan 1, 1997

By Jeff Senules, Oana Meins, Catherine Aimone-Martin, Scott Lanker, Brent Meins

Global wall strains from 4 to 77 micro-strains were measured at three structures adjacent to a highly-confined Florida quarry blast when PPV amplitudes ranged up to 6.05 in/s. Increasing the peak zero-crossing frequencies with carefully control delay timing helped to lower ground displacements affecting wall strains.

Feb 1, 2020

By Alexandra Yuyali

The objective of this research work is to increase the drilling ratio represented in tons per drilled meter (ton/m) to reduce mining costs. One of the key characteristics of this research is the use of the ITH (in-the-hole) drilling rig with a water-powered hammer, also known as Wassara™. The patented Wassara™ in-the-hole hammer is powered by high-pressure water instead of air. To reach the objective, a new design of the blast pattern was implemented considering the following: Burden from 1.7 m (5.6 ft) to 2.8 m (9.2 ft) Spacing from 1.7 m (5.6 ft) to 2.7 m (8.9 ft) Drill diameter from 89 mm (3.5”) to 102 mm (4”) Drilling length from 15 m (49 ft) to 30 m (98 ft) Borehole deviation < 2% The result of this new design is the optimization of the drilling ratio (ton/m); having as a baseline 5.2 ton/m with traditional equipment and obtaining 13.7 ton/m with the ITH drilling, which generates annual savings of $2.43M.

Jan 21, 2025

By John Brulia, Grant ODell

The AIRDEK blasting method has recently been introduced as an overbreak control blasting technique. This paper discusses the use of a modified AIRDEK blasting method for use in open-face blasting to make cap stone riprap (6-20 ton size) at the Clinton Point quarry of New York Trap Rock Corporation, Lone Star Industries.

Jan 1, 1990

By Dale L. Ramsey

The Pinkerton Tunnel Open Cut Project is part of the National Gateway Clearance Initiative improvement project to achieve a minimum of 6.4 meters (21 feet) of vertical clearance along CSX Transportation rail corridor so that double-stacked intermodal railcars can be transported between Mid-Atlantic States and their ports to Midwest Markets in the U.S.

Jan 1, 2014

By Martin Reed, John Wright

Blasters with the United States Antarctic Program (USAP) have developed techniques for opening access holes in floating sea-ice where the use of conventional drilling equipment is impractical. The blasting techniques have proven successful in sea-ice ranging from 8 to 15 feet thick. Previous published work has treated in detail blasting holes in floating ice from 2 to 6 feet thick.

Jan 1, 2001

By Clara Godoy, Paulo Couceiro, Juan Navarro

The continuous automatization and digitalization of the different stages involved in any underground construction bring new possibilities to optimize the operation. One of the most important requirements for the development of these projects consist of a proper rock mass characterization for optimizing the stages of the drilling, blasting and support cycle. In the last few years the road to digitalization has gone through data science and big data, showing the importance of data gathered to describe the geological and geotechnical environment that surrounds the operations. Since rock characteristics have an important influence in the drilling response, the technological advances in the sensorization of drilling machinery such as the Measurement While Drilling system (MWD) allow to gather the necessary amount of information to be applied in data science processes to evaluate changes in the rock mass with higher resolution than conventional methods. In this paper, Machine Learning techniques have been used to combine data monitored from the drill rigwith scanner profiles of the excavated sections to develop an automatic geotechnical rock mass characterization model able to estimate potential zones of over- or under-break of the remaining rock mass in underground blasting. By comparison of scanner profiles of the excavated sections with the blasthole positions, an Excavated Mean Distance (EMD) between the contour blastholes and the excavated profile has been obtained, which may be considered as damage measure. Considering blasting factors as constant, the model combines the rotary, percussive, hydraulic flushing and the rate of advance of the drilling, and the confinement of the rock mass by depth, to detect zones with different rock properties. This provide an early information of the rock mass condition around the blastholes and the prediction of expected overbreak generated after blasting, being possible to design more efficient bastings, in which each borehole is filled with the right and necessary explosive charge. The analysis comprises data from 57 blasts (around 1700 contour blastholes) and more than 4000 excavated sections.

By Clara Godoy, J. A. Sanchidrian

In this paper, Machine Learning techniques have been used to combine data monitored from the drill rig with scanner profiles of the excavated sections to develop an automatic geotechnical rock mass characterization model able to estimate potential zones of over- or under-break of the remaining rock mass in underground blasting. By comparison of scanner profiles of the excavated sections with the blasthole positions, an Excavated Mean Distance (EMD) between the contour blastholes and the excavated profile has been obtained, which may be considered as damage measure.

Feb 1, 2020

By Ruilin Yang

The vector sum peak particle velocity (PPV) of blast vibrations describes the blast vibration intensity more completely than the PPV of a single component waveform. It is more logical to use a vector sum PPV as a vibration limit than using a single component PPV. In 1980 the USBM recommended the frequency related peak particle velocity criterion. So far this method has been only applied to single component waveforms, but not to the vector sum PPV since there is no method available to associate a frequency to the vector sum PPV. The present paper describes a method to define a principal frequency associated with vector sum PPV. The method is based on the weighted average of the principal (zero-crossing) frequencies of the three tri-axial components at the time of the PPV.

Jan 1, 2015

By Ken Fiorentino, Gordon F. Revey

H3 Tunnelers recently excavated two conventional 48 foot diameter highway tunnels through the Halawa side of the Tran-Koolau Mountains on Oahu. The primary blast design challenge on this Job was minimizing overbreak In the alternating layers of pahoehoe and aa lava, clinker, end tuff. Two different excavation techniques were evaluated in the Halawa tunnels. The first method used drilling and blasting to excavate the tunnels to within one foot of their final perimeter. A roadheader, mounted on a backhoe, was then used to excavate the remaining foot of ground. The second method used conventional smoothwall blasting techniques, without any mechanical excavation. This paper describes the details and relative success of the two excavation methods tried in the Halawa tunnels.

Jan 1, 1993

By David Harrison

The Charleroi Locks and Dam (Figure 1) was completed in 1932 and is located on the Monongahela River, approximately 22 miles (35 km) south of Pittsburgh, in Charleroi, Pennsylvania. It is comprised of a 420 foot (128 m) gated dam, and a 720 foot (219 m) by 56 foot (17 m) land side lock which provides for a 16.6 foot (5 m) vertical lift.

Jan 1, 2015

By Robert Hopler

On June 13, 1912, the final decree of dissolution of the DuPont explosives trust was handed down, and the resulting new companies began operating at the beginning of the new year. The property assets granted to (or retained by) the companies were as follows:

Jan 1, 2014

By J Lyall Workman, Peter N. Calder

Large hole rotary drilling is one of the most common methods of producing blastholes in open pit mining. Large hole drilling generally refers to diameters from 9 to 17 inch (229 to 432 mm), however a considerable amount of rotary drilling is done in diameters from 6½ to 9 inch (165 to 229 mm). These smaller diameters are especially prevalent in gold mining and quarrying.

Jan 1, 1996

By David Harrison, Brian Harrison

The Army Corps of Engineers completed the Charleroi Lock and Dam in 1932. It is located on the Monongahela river approximately 22 miles (35k) south of Pittsburgh in Charleroi, Pennsylvania. It is comprised of a 420-foot (128m) gated dam, and a 720-foot (219m) by 56-foot (17m) land side lock, which provides for a 16.6 foot (5m) vertical lift.

Jan 1, 2018

By John Hutchings

Drilling and blasting is a clearly delineated work process, which has well defined inputs and outputs. Drilling and blasting is also a process with a number of steps each of which has measurable outcomes. Drilling and blasting is ideally suited to the application of Total Quality Management principles. Most drilling and blasting information is generally poorly managed with disjointed and unrelated Information Technology systems managing parts drilling and blasting data. Data is often moved from on system to another, sometimes manually. In the field, drilling and blasting is still very much a paper based system and which has not generally benefited from some of the recent hardware and software technology advancements now “on the shelf”. Data collected on paper rarely is transcribed back into an electronic system for further analysis. It is often difficult to collate or review historic drilling and blasting data. This paper will present a definition of Total Quality Management and demonstrate how it can be applied to the drilling and blasting work process. Total Quality Management defines the mechanisms for the application of continuous improvement to drilling and blasting. Continuous improvement will provide opportunities to modify drilling and blasting work process outcomes and generate real cost benefits within the overall mining process. A complete drilling and blasting management system frame work, called DBS, is presented in this paper. DBS provides all the components necessary to implement a full drilling and blasting Total Quality Management solution. Also highlighted will be appropriate “off the shelf” technology that can be applied to replace current paper based systems and provide the means to connect with other mine data systems. Various examples will be discussed which will demonstrate potential benefits of applying a structured Total Quality Management approach to a drilling and blasting work process.

Jan 1, 2004

By Carlos Enrique Arroyo Ortiz, Jadir Pedro Alves

This paper presents some of the results obtained during the research work about the use of technologies and digital transformation in the process of rock drilling in open pit mines. The use of automation presents itself as a disruptive factor and a driver of improvements that provide sustainability in rock drilling. Seven main operational parameters were utilized to combine measurement while the drilling (MWD) with other information generated by the equipment during hole drilling, in six different lithologies in an iron mine, located in the central region of Minas Gerais in Brazil. Adjustments and corrections were made to the data collected in order to minimize external influences other than the rock itself, to ensure the effectiveness of the analyses. Finally, we sought to compare the performance of the drilling process in manual and automatic operation modes. Thus, making it possible to show the efficiency and impact on the sustainability of rock drilling operations in open pit mines.

Feb 6, 2023

By Yogesh Narula

Nevis Bluff Landslide - On September 17” 2000, a rockfall measuring lO,OOOm3 at Nevis Bluff, New Zealand, triggered a loday emergency. It ended when a hazardous column of rock that towered over State Highway 6 was finally shattered. The operation called for unusual and unique solutions using aerial bombing and inverted blasting techniques, not known to have been attempted before under these conditions, anywhere in the world.

Jan 1, 2002

By Paul Worsey, Barbara Robertson

In June 2007, Missouri Science & Technology (formally UMR) successfully held its 5th and 6th Explosives Summer Camps. The camps, which include substantial industry participation, have been an outstanding success with both the students and their parents. They have also spawned a large amount of local, state and national media attention, including NPR and an article in the New York Times on the 3rd of July 2007.

Jan 1, 2008

By Svatopluk Zeman, Zbynek Akstein, Jiri Pachman, Ahmed Elbeih, Marcela Jungova

BCHMX (cis-1,3,4,6-tetranitro-octahydroimidazo-[4,5-d]imidazole or Bicyclo-HMX) was studied as an energetic component of three different plastic explosives based on three matrices: C4 matrix, semtex10 matrix and silicone matrix. The original plastic explosives, Composition C4 - based on RDX (1,3,5-trinitro-1,3,5-triazinane), Semtex 10 explosive based on PETN (pentaerythritoltetranitrate) and plastic RDX-silicone, were included for comparison. Sensitivity and performance parameters were studied.

Jan 1, 2011