Search Documents

Existing geological structures such as faults or shear zones can greatly influence the interpretations of amplitude or energy attenuations of measured blasting vibrations along both affected and unaffected orientations. Mineralisation in conjunction with large faults or shears is commonplace in the geology of steeply dipping metalliferous deposits, such as those found in the goldfields of Western Australia. Better understanding of the influence of faults or shear zones on blast-induced seismic waves can lead to more effective blast vibration monitoring programs and interpretation of the results measured along affected orientations.

Jan 1, 2011

By Andrea Francioso, Roberto Folchi

In order to comply with the latest European Highway Standards, the highway Salerno - Reggio Calabria, in southern Italy, had do be widened and upgraded to reduce its vulnerability to earthquakes. Reinforced concrete viaducts, no longer needed for the new road, had to be demolished. Many bridges still to be used for the highway required refurbishment due to 50 years of wind, frost and salt corrosion. This re-furbishment and new construction had to be carried out simultaneously. To keep the highway open dur-ing the renewal process, all traffic was directed to one side of the road. Demolition was conducted ex-tremely close to operational roadways and viaducts, as close as only 2 cm (0.8 in). Care had to be taken to ensure that the stresses (vibration levels), resulting from the demolished pylons and decks hitting the ground, were below the no-damage thresholds for the nearby acceptors (structures receiving the vibra-tion stresses). These structures included bridges, houses and buried pipelines (water, oil and gas). In some cases, care also had to be taken to preserve the existing pylons supporting decks that were being demolished; since the same pylons were going to be used for the new viaducts (bridges). New continu-ous decks in weathering steel replaced the old reinforced concrete decks.

Jan 1, 2013

By Jung-Hoon Ryu, Chang-Ha Ryu, Byung Hee Choi, Yang-Kyun Kim

Control of overbreak in tunnel blasting is one of the key factors affecting the construction expenses as well as safety. Overbreak causes an increase in the cost of construction by requiring an additional amount of shotcrete. In addition, blast damage to the final rock face may cause instability and rock fall hazards. For these reasons, controlled blasting is an indispensable routine in tunnel excavation in order to get a smooth face and to reduce damage to the final wall. We have experienced a very poor quality of excavation depending on the tunneling sites although a similar design of controlled blasting technique was applied. Field experiments over 40 rounds were carried out to investigate the cause of the poor results in tunnel blasting. In this paper, discussed are the parameters affecting the overbreak and some findings from the field experiments. Overbreak could be controlled considerably by adjusting some parameters before the efforts of developing a new blasting method.

Jan 1, 2004

By M Lemieux, R Mason

The SABREX blast modeling program was introduced to I.O.C.C.'s Carol Lake Iron Ore Project in December 1987. As part of CIL's Technical Services, SABREX was used to implement an optimization program designed to analyze and introduce various grades of MAGNAFRAC at a constant pattern while maintaining acceptable blast results.

Jan 1, 1989

By Italo Onederra, Gary Cavanough, Ewan Sellers

Reactivity of ammonium nitrate based explosives is associated with the presence of iron sulfides in the ground reacting with explosive products and in some instances causing spontaneous reactions which can lead to detonation. The stability of explosive products can also be linked to in-hole density, which influences detonation efficiency, breakage performance and the potential generation of Nitrogen Oxide (NOx) fumes. Reactive ground testing involves detecting a temperature rise of a mixture of a bulk explosive product sample, a ground rock sample and some specific chemical agents. This paper describes improvements in reactive ground testing involving the use of time lapse video analysis and detection of NOX gas emissions from the sample. Reactivity is stored and linked to a using cloud based software to map of the mine showing the exact location of the sample. The location marker can be selected to allow quick access to the sample test results and video. In addition to reactivity, the stability and detonation performance of bulk product can also be influenced by depth. In this paper, a system that simulates product at depth and measures density changes and monitors the structure of bulk samples is described. Results from an explosive product are analyzed and detonation performance is assessed by the measurement of velocity of detonation and detonation pressure.

Jan 1, 2018

By M. K. Ameen, R. El-Hacha

This paper presents the analytical results obtained from numerical simulation of reinforced concrete slabs strengthened with various FRP systems and subjected to blast loading. A three-dimensional finite element model using AUTODYN software was used to predict the overall behavior of the slabs. The numerical results were validated by comparing with experimental results from a program carried out to investigate the efficiency of different strengthening systems on the blast resistance improvement of small-scale reinforced concrete (RC) slabs. The experimental program consisted of testing nine RC slabs strengthened with three different externally bonded (EB) FRP systems attached at the bottom side of the slabs and one RC slab tested without strengthening for comparison purposes. The EB FRP strengthening systems investigated included two layers of Carbon Fiber Reinforced Polymer (CFRP) sheets, two layers of Glass Fiber Reinforced Polymer (GFRP) sheets, and one layer of Glass-Fiber Resin Polymer (GRP) sheet. Different epoxy resin, patching mortars and impregnating epoxy adhesives were used for the slab surface preparation and FRP system application of the strengthening layers. The aim was to evaluate the residual strength of the test specimens after exposure to blast loads. The blast loading parameters were evaluated for each test using AUTODYN simulation and compared with the computer program CONWEP. All specimens were subjected to same spherical TNT charge weight and stand-off distance with the respect to the slab top surface. Extensive comparison is made between the experimental results and the AUTODYN simulations for the control unstrengthened slab and the strengthened slabs including time history records of the bottom steel strain and mid-span acceleration and the peak dynamic deflection of the slabs.

Jan 1, 2010

By J. D. Aubertin

Rock blasting is a complex engineering process that requires in-depth knowledge of operations and geomechanical conditions. Acknowledged design precepts are based on cratering behavior associated with stiff hard rock masses. Other cratering mechanisms may however arise under certain geomechanical conditions such as extremely fractured rock masses, or with soft rocks such as rock salt and potash. The burden dimension also plays an important role in the prevalent cratering mechanisms of a given blasting condition. The present article investigates the variability of cratering profiles and geometrical trends based on characteristic geomechanical differentiation and considering the influence of burden. The differences in observable mechanisms are examined through small and large-scale single hole blast (SHB) tests. SHB tests involve a series of individual shots blasted parallel or sub-parallel to an open face. The burden dimension is varied to obtain burden dependent characteristic trends. The breakout shape is represented by a crater model in the form of a power law equation capable of describing prismatic, concave and convex cratering. The formulation comprises two reference index parameters that can describe the geometrical and geomechanical conditions. SHB test campaigns conducted in rock salt, limestone, massive amphibolite, pinolite, and grout blocks are compiled in quantitative manner to demonstrate the influence of geomechanics on cratering profiles. The observed trends are corroborated through numerical modelling carried on Finite Element Model (FEM) LS Dyna to investigate the prevalence of specific cratering mechanisms. A series of SHB tests at large and small burden values are also used to showcase the influence of geometry on the prevalent cratering mechanism and the resulting crater

Jan 1, 2024

By Virgil J. Stachura, Calvin L. Cumerlato

The U. S. Bureau of Mines is conducting research on blasting methods that reduce highwall overbreak and the associated rockfall hazards. This paper presents the results of tests using a low-density water gel to improve the quality of air-decked presplit blasts at a surface coal mine in New Mexico. The explosive's specific gravity averaged 0.50 and was bulk loaded using a modified truck which injected the gassing agent. Reductions in overbreak and resulting rockfall were achieved in comparison to a highwall presplit with ANFO. The test sections used 15° angled blast holes and resulted in 1,119 m (3,672 ft) of air deck presplit highwall using a low-density water gel which was then compared to 894 m (2,934 ft) of highwall shot with an ANFO air decked presplit design. The total quantity of explosives per hole ranged from 68 to 113 kg (150 to 250 lbs) and the 27 cm (10-5/8in) holes were 19- to 33-m (62- to 108-ft) deep on 5.5 m (18-ft) centers. Periodic visual examination and photographic surveys of the highwall test areas were used to document the amount of rockfall. In addition, laser profiles of selected sections were conducted to further delineate the damage and highwall contour differences.

Jan 1, 1995

By Terry Nichols, Karl E: Warkwick Burgher, Charles J. Wideman

The application of Fourier spectral analysis to records of ground vibration generated by over 100 explosions from an open pit mine is used to develop empirical predictor equations that relate the response spectra to the blasting parameters used to generate the excitation motion. Time series representations of ground particle velocity are transformed into the frequency domain where the appropriate modifications are made such that the inverse Fourier transform yields the time series representation of particle displacement and acceleration. Compensations are made for the transform function of the recording system in the frequency domain. Spectral analysis of the three types of ground motion is correlated with the blasting parameters. The results show that the frequency content of ground vibrations generated from a mine blast can be quantified in terms of the predictor equations.

Jan 1, 1990

By Robert A. Cummings, Francis S. Kendorski, Charles H. Dowding

During the summer of 1980, a field project was carried out to determine the stability of the beautiful and dramatic natural limestone pinnacles (locally termed "Hoodoos") at Bryce Canyon National Park, Utah, when subjected to ground motions and airblasts resulting from proposed strip coal mine blasting. The concern arose from environmental considerations associated with the proposed development of a large coal strip mine which would approach within 4 miles of the park. The pinnacles range up to 150 ft in height and are quite slender, producing a fragile appearance. The remoteness and ruggedness of the area required a field camp, and 4-wheel drive vehicles, helicopters, and snowcats for support. Portable magazines were necessary to store the more than 7 tons of blasting agents and explosives required. In conducting the blasting, great attention was paid to environmental impacts. In the field, a target pinnacle was selected and instrumented with mechanical strain gages, and research seismographs that required helicopter placement.

Jan 1, 1982

By R R. Singh, U K. Dey, S K. Roy

"Commercial explosives being a heterogeneous mixture of many chemical compounds in prefixed proportion, their velocity of detonation (VOD) may vary from batch to batch, due to variations in the proportion of the chemical composition and process parameters even within their tolerance limits. Inherent limitations of measuring methods and human variations during measurement also add to the variation in VOD values determined practically. Therefore, it is customary to define a range of VOD values rather than a fixed value of VOD for a particular explosive.Variations in VOD values of four commercial permitted explosives in India were evaluated under open unconfined condition using Dautriche method and a resistance wire method based continuous VOD meter. Comparative evaluation of VOD values of selected explosives were aimed to check the relative effectiveness of continuous VOD measurement of small diameter cartridged permitted explosives using cheaper co-axial wire instead of recommended costly VOD rods along with the continuous VOD meter. Results of evaluation revealed that continuous VOD of commercial small diameter cartridged explosives could be determined using cheaper co-axial resistance cable with comparatively better accuracy than the most commonly used Dautriche method."

Jan 1, 2007

By Thierry Bernhard, Johan Finsteen, Charles Dowding, Mathias Jern

To bring some clarity to how different standards relate to each other a project was initiated within the European Federation of Explosives Engineers (EFEE). The first part of the project was a literature study and a survey including an evaluation of the answers provided by members of EFEE. The results were presented at the International Society of Explosives Engineers (ISEE) conference in Denver 2020 as well as the EFEE conference in Helsinki in 2019.

Feb 1, 2020

By Hernan Navea, Carlos Alvarado, Exequiel Nuñez, Matías Suarez, Jhon Silva, Bryan Townsend, Bryan Caceres, Felipe Pontanilla

Nowadays, technology dominates all aspects of human activities, and drilling and Blasting (D&B) is no exception. In most cases, the use of technology in D&B is focused on controlling individual activities such as drill performance, drilling advance rates, truck loading performance, etc. Still, in very few instances, the advantages of using technology along each D&B activity and how this influences the D&B results are documented. This paper shows how technology is applied to create a “relative hardness” model for the mine Caserones in Chile. In the future, the model can relate the relative hardness parameter to several variables, including excavation rate, fragmentation results, and vibrations. It can also be used in the explosives loading process, similar to the model used by Dyno Nobel’s Differential Energy (DE) technology. In the relative hardness model for Caserones, a design is loaded in the drill system, and data is collected during the advance of the blasthole. The collected data includes rpm, torque, pressure, etc. Then, an algorithm using the measured variables while drilling and known relationships between the properties of the rock and the drill's performance is used to classify the average relative hardness of the blasthole in four intervals: hard, medium, soft, and very soft. Optimization techniques and models used in the oil and gas industries to analyze drilling performance were adapted to implement the algorithm. The model uses the concept of mechanical specific energy (MSE). Using the data from the drill, the algorithm identifies the depth where the MSE reaches a minimum to calculate the “relative hardness” for the blasthole under analysis. The results are presented in maps highlighting the areas where hard, medium, soft or very soft rock masses are expected. That information can be used to anticipate areas where explosives with higher energy need to be used or to predict areas of the blast with additional digging difficulties and then lower loading rates. The paper shows examples where “relative hardness” maps are compared to drilling speed excavation rates and other variables.

Jan 21, 2025

By Jose Pineda, Abraham Lindo

The Panama Metro System’s Network expansion involves excavating a launching shaft for a tunnel boring machine (TBM) to traverse beneath the Panama Canal. The blasting needed for this shaft construction poses significant challenges due to the presence of concrete walls encircling the excavation. These walls must remain intact throughout construction and the tunnel's future operation. This case study is focused on devising and implementing safe blasting techniques crucial for the shaft's construction, ensuring the preservation of surrounding concrete walls and project equipment. As the interest was potential damage to the concrete walls, an appropriate vibration threshold for this project was also required as an alternative to the traditional U.S. Bureau of Mining RI-8507 limit (USBM RI8507). Blast modeling software was employed to conduct a series of blasting simulations. Parameters like hole diameter, spacing, depth, explosive type, and initiation methods were varied to evaluate their potential effects on wall stability and damage risk. The simulations revealed that smaller diameter holes and reduced spacing between blast holes would effectively mitigate the risk of wall instability. Additionally, utilizing electronic delay detonators and carefully planning the blast hole detonation sequence proved critical in minimizing potential damage. Executing these blasts in the field presented unique challenges, including strict charge per delay thresholds and logistical constraints. Consequently, continuous adjustments to blasting parameters were made and comparative result analysis. Beyond providing a safe blasting strategy for the TBM launching shaft, this study offers invaluable insights into adapting blasting designs to align with environmental and structural safety standards. These findings hold great potential to shape guidelines for analogous sensitive construction projects. They underscore the importance of leveraging prior research as a reference point, engaging with project designers and local authorities, and continually conducting testing and adjustments to ensure project success.

Jan 21, 2025

By Türker Hüdaverdi, Özge Akyildiz

"Efficiency of blast operations depends on fragmentation, overbreak, muckpile profile anddisplacement, vibration, airblast, flyrock and damage to wall or slope stability. To provide all these conditions at the optimal level, determination of rock mass properties (in-situ block size, joint spacing and orientation) is the very first step during design stage of rock blasting. Image analysis software is used not only to determine the fragmentation level of muckpile but also to characterize the bench face. In this study, an image analysis software was used to determine apparent block size of bench face and to measure blast fragmentation of muckpile. The source of errors and the vital points to be taken into consideration were explained for bench face characterization andfragmentation measurement. Since it provides much better results than previous techniques and it is not intrusive to production process, image analysis technique is considered as one of the most efficient and preferred way for fragmentation analysis. Besides these advantages, there are some weak points of image analysis software. Lighting is one of the most important factors for photographs captured for in-situ block size analysis and fragmentation analysis. Lighting determines shadow formation. In an ideal image, particles are clearly delineated by soft shadows. If shadows are too strong (dark), analysis suffers. Appropriate scale should be replaced onto blast muckpile during site measurements. The location of the scale in image affects the results of analysis. Also, the densityand orientation of discontinuities should be considered during application of image analysis technique to characterize bench faces. In this study, image analysis software was applied in thesandstone, limestone quarries of Istanbul region and an open pit boron mine. All image analysis, evaluations and results were made based on the site measurements."

Jan 1, 2017

By Kim Henley, Chris Batten

This paper discusses the use of the Orica WildFireTM flyrock model to help mining operations in Australia and Asia minimise blast exclusion zones for equipment, increasing utilisation and productivity and delivering downstream value

Feb 1, 2020

By Ruilin Yang

Kinematic approach of blast modeling refers to using the velocity, strain, or displacement as controlling parameters to model blasting, rather than the stress and the material constitutive relations. The rock stiffness or constitutive relations is very hard or impossible to obtain due to the complexity of the rock mass property.

Feb 1, 2020

By Peter Moser, Mark Ganster, Radoslava Ivanova, Florian Bauer

Blasting accurately in underground drifts and creating a smooth contour requires proper drilling, knowledge about the apparent geology, a well designed blast pattern and ideally a smooth blasting product. These products are usually cartridged explosives with less energy and are charged in the contour holes in order to reduce the energy concentration and therefore the cracking into the surrounding rock. With the development of a new contour blasting system, a device can now be delivered to the industry that that avoids the additional storage of cartridged products when bulk explosives are used. The system consists of a foldable hose that is charged with bulk emulsion, in the same way as the rest of the blast, from the base to the collar of the hole. It centers automatically in the borehole and provides a decoupled charge. The paper describes the system in detail, gives background information on smooth blasting and presents the first successful field tests using the system in the drifts of an underground mine. It shows the advantages of blast results that produce more stable contours that reduce the amount, time and cost for support but also increase safety underground.

Jan 1, 2012

By Zhiwei Jiao, Ziqing Guo, Mushen Wang, Yueda Fang, Qiuming Tang

In order to achieve anti-terrorism, production safety, better explosive performance, lower cost, and environment protection, we developed HMS (emulsification in borehole).Long-process PM (plant-mixed) and SM (site-mixed) emulsion trucks are reviewed and compared to a new type of short-process HM (hole-mixed) truck for onsite emulsion manufacturing. The short-process HM truck has demonstrated many advantages over its PM and SM counterparts in areas such as process safety and security, energy efficiency and environmental impacts: 1) No emulsion matrix is manufactured in the plant, transported on public roads, or even present on the surfaces of blasting job sites. Such characteristics are certainly beneficial in eliminating risks of the product being diverted and used by unlawful players; 2) This short-process involves "micro-fluid control to form super oil phase-rich" in tubular emulsification process, making it intrinsically safe; 3) There is basically no residual matrix left in the truck or on the job site to clean up, which greatly reduces environmental impact of the process; 4) Comparing with typical PM and SM trucks, the HM truck has eliminated the needs of many power equipment and critical pump pressure for turbulent flow forming a static emulsification with super oil phase -rich is only 0.2Mpa. These is therefore quite energy efficient.

Feb 1, 2020

By Patricia Mendoza Watson, Lundquist Robert G

The velocity with which the burden moves after blasting is of concern for safety and economic reasons. Models developed for motion velocity by various researchers were reviewed and likely model parameters were used to develop statistically significant models. Regression analysis and residual analysis were used to determine the model coefficients and the accuracy of the models.

Jan 1, 1990