Search Documents

By S. F. Kaplan, A. S. Dolotov, V. N. Kovalev

"The proportion of refractory sulphide ores and concentrates in world gold mining industry is growing every year. Pressure oxidation of these materials (in autoclave) allows to oxidize gold hosting minerals. Traces of halides and pseudohalides present in the slurry liquids contribute to formation of complex gold compounds. Sorption-active carbon present in ores leads to irreversible adsorption of complex gold compounds and their loss. The objective of the research is to study gold extraction dependence on the concentration of chloride-, cyanide- and thiocyanate-ions in the slurry liquids during pressure oxidation. Double refractory flotation concentrate of the Bakyrchik deposit was used for the testwork. The research was planned on the basis of a full factorial experimental design with additional refining experiments. Ligand concentrations (0 – 1000 mg/l Cl-, 0 – 600 mg/l CN-, 0 – 1200 mg/l of SCN-), temperature (200 – 240 °?) and retention time (1 – 6 h) were used as variables of pressure oxidation process. It was determined that sulfide minerals oxidize much faster than ""organic"" carbon. Under the conditions of T = 240 ?C, t = 2 h, sulphide sulfur oxidation was 95.6%, while ""organic"" carbon oxidation was 46.1 %. Each of the examined ligands has a significant adverse impact on gold extraction. Analysis of the experimental data demonstrated that with a high degree of confidence (R2 = 0.883) gold extraction does not depend on the ligand type, but only on its concentration and the ""organic"" carbon oxidation degree. In case of complete oxidation of ""organic"" carbon, the presence of the ligand (L = Cl-, CNS-, CN-) in the liquids at a concentration of up to 20 millimole/L does not significantly affect gold extraction. The assumption that the main factor of preg-robbing in ???-CIL treatment of double refractory concentrates is the natural ""organic"" carbon sorption-active to gold has been confirmed. INTRODUCTION In recent decades, placer gold mining has been gradually declining and hardrock gold mining, including ""refractory"" gold mining, has been growing all over the world, as well as in the Russian Federation (http://www.miningworld.ru, 2015). One of the main reasons why gold ores are refractory is gold adsorption on natural carbonaceous materials (""organic carbon""). Only a few technologies are suitable for processing such ore concentrates (a significant amount of gold is contained in refractory hardrock ore both in Russia and worldwide) (Vorob'yev-Desyatovskiy N.V., Yepifanov A.V., 2014)."

Jan 1, 2018

By L. Bbosa

Positron Emission Particle Tracking (PEPT) and the Discrete Element Method (DEM) are used to investigate Power Draw in a laboratory scale tumbling mill. The mill is run dry in batch mode at different speeds using mono-size charge of glass beads, and is mounted along with a torque transducer to measure power. Particle tracking information from PEPT is used to reconstruct the motion of glass beads and infer the overall charge behavior, while DEM is employed to simulate particle motion and interaction, with collision mechanics calculated using the Hertz-Mindlin contact model. For PEPT and DEM data, the product of torque and average angular velocities in discrete cells are accumulated to obtain mill power. This method is found to be within statistical agreement with measured power for all tests. Spatial distributions plotted from this approach highlight the regions of the mill that draw the greatest power. A second technique to obtain Power Draw from DEM data which sums particle forces against the mill geometry is similarly found to accurately predict mill power with lower statistical error. Keywords: Power Draw, PEPT, DEM

Sep 1, 2012

By S. F. Kaplan, A. S. Dolotov, V. N. Kovalev

"At this point in time, autoclave recovery (POX) followed by sorption cyanidation (CIL) is one of the most promising technologies for the efficient processing of refractory and double refractory gold-bearing sulphide rock. This hydrometallurgical technology requires the use of a large amount of water (up to 5 tons per ton of used concentrate), resulting in highly saline water with high pH (pH 9-11), high content of cyanides (up to 300 mg/l), arsenic compounds, antimony and a number of heavy metals. In order to determine the possibility of using recycling industrial water in POX-CIL technology, several batches of experiments were conducted (using the double refractory flotation concentrate of the Mayskoye deposit). Urban water with a chloride ion content of 10 mg/l was used during the reference POX-CIL experiment as the liquid phase of the ??? feed pulp. At that, gold extraction rate amounted to 89.4 %. A full cycle of POX(200 ºC)-CIL was carried out during the first part of the experiments; at that, fresh concentrate of the untreated recycling water with cyanide ion content of 95.4 mg/l, left after the completion of the previous CIL cycle, was used for repulping. It has been established that direct use of untreated recycling industrial water is impossible due to a sharp decline in gold extraction (preg-robbing) down to 79.5%. The presence of chloride ions, cyanide ions and other ligands in the liquid phase provides effective complexion formation for the recovery gold; complex gold compounds are quickly and firmly sorbed by the natural carbonaceous substances of the concentrate at the stage of autoclave recovery; they are virtually not cyanized onwards, and gold is carried over to the tailings. During the the second batch of experiments, recycling industrial water with cyanide and chloride ions' concentration of 500 mg/l each was subjected to the reverse osmosis desalination (up to 6 times in a successive order). After each desalting cycle, such water was used as the liquid phase of the feed pulp in POX-CIL. 6 cycles of RO desalination enabled the extraction of 86.1% Au (which is close to reference recovery). During the third batch of experiments, recycling industrial water was diluted with distilled water (2, 4, 16, 32, 64 times); after each dilution cycle, this water was used as the liquid phase of the POX-CIL feed pulp. Gold extraction after 64-fold dilution amounted to 82.6%. The results of the conducted researches show that the use of untreated recycling industrial water in POX-CIL hydrometallurgical technology is absolutely impossible due to a sharp decline in gold extraction. Even the 64-fold dilution with pure water is inefficient both from the perspective of gold extraction and of rational use of water. Reverse osmosis desalination solves the problem of water treatment except for the removal of cyanide ion, which requires separate reagent treatment of water."

Jan 1, 2018

By Thenepalli Thriveni, Seong-Young Nam, Nam-Il Um, Joobeom Seo

In the present work, we report a novel microstructure of synthesized scalenohedral PCC (precipitated calcium carbonate) without any additives by a simple and ecofriendly carbonation process carried out in a liquid-gas system on the crystal growth of the scalenohedral calcite phase. Especially, the process parameters of Ca(OH)2 concentration and CO2 flow rates were investigated to enhance the sensitivity of the process. The highest average length of the scalenohedral calcite was obtained at pH 6.0, temperature 450C, Ca(OH)2 concentration 0.2M, CO2 flow rate 80mL/min, and total volume 1L. The utilization of flue gas-derived CO2 from coal fired power plants could be a form of carbon capture and storage using carbonation reaction with scalenohedral PCC. Finally, the synthesized scalenohedral PCC was used as a filer for ONP recycling. We demonstrated all these experiemnts at semi pilot plant scale.

Jan 1, 2014

By Jens Markowski

The EU Directive 2000/53/EC on end-of life vehicles (ELVs) states that in 2015 at least 85 wt.-% of a vehicle has to be reused or recycled. This result in the obligatory need to separate additionally metallic and other components of the automotive shredder residues (ASR), so that they can be professionally prepared for recycling and reuse further. Currently the iron-containing fines of ASR are deposited as it is not possible to process in blast furnaces due to its particle size (< 4 mm), composition and material properties. Additionally problems are also caused in handling and transportation (dust) of the material. This work focuses mainly on the ASR materials utilization in blast furnaces. Material was further separated into two consecutive fractions by carrying out repeated crushing and magnetic separation twice. The two fractions have significantly higher iron content (up to 75 wt.-%) compared to the initial material mixture. The materials were assessed for their usage in blast furnaces based on the possible pelletisation with and without binders, stability of pellets, shape and size of pellets, etc. Pelletisation of the material was carried out with a single mould pellet press. Further lignite coal was added to the mixture as additive which improved the pelletisation behavior and the mechanical stability of pellets. Lignite coal was chosen as a reducing agent in the blast furnace process contributing towards additional savings in energy supplied. The experiments reveal that the production of pellets from iron-containing fines is possible with a lignite coal admixture of about 15 wt.-%. These pellets displayed good mechanical stability and can be used in blast furnace processes in recovery of the recyclable metals which are currently not recycled. The recycling of not yet recyclable metals would reduce the deposition and can be easily adopted into the economic cycle by their utilization. Keywords: Automotive shredder residue (ASR), FE-fines, pelletisation

Sep 1, 2012

By T. Mütze

The progress in comminution is often described by the specific surface area and the energy utilization or the brakeage ratio and breakage function. The principal mechanisms of size reduction are therefore, well known. All four parameters share a common disadvantage: They are limited in describing the behavior of a feed material with fine particles and a wide particle size distribution. An alternative is to describe the progress in comminution with ? The particle size distributions Q(x) before and after the stress or ? The particle concentration ratio pcr(x), which combines these two states. In the case of a self-similar fracture behavior, (in short: self-similarity) the progress in comminution can be simplistically described by the relationship between a reference particle size and the stress intensity. Self-similarity means self-similar breakage functions of geometrically similar particles of the same strength, a certain stress situation and stresses up to the breakage point. Self-similar breakage functions show the same curve at different stress intensities when the fragment size x is normalized with a reference particle size xNorm. This behavior was demonstrated for single particle comminution repeatedly and unequivocally. In the field of particle bed comminution, these results differ in literature. Therefore, the self-similarity in particle bed comminution was systematically investigated at the Institute of Mechanical Process Engineering and Mineral Processing of the TU Bergakademie Freiberg as part of a research project. Limestone, quartz, silicon carbide and glass beads, were examined with a hydraulic press. The particle sizes covered monodisperse fractions in the range of 1-1000 µm, bimodal mixtures of these fractions and polydisperse fractions. The results obviously show that there is no self-similar fracture behavior in the case of glass beads, quartz and silicon carbide. Statements on the self-similarity of limestone are much more difficult: Only some of the investigated limestone fractions show a similar clear, non-self-similar behavior. Self-similar curves appear particularly for fine monodisperse fractions as well as bimodal mixtures, which stressed with pressures above 200 MPa. Considering the measurement accuracy of particle size analysis the coincidence of the curves can be explained by the fact that progress in comminution almost ends above 200 MPa. At this point, a hydrostatic stress state is reached in the particle bed which is known from the literature. This stress state inhibits further fractures. Overall, it has been verified for the investigated materials that there?s no self-similar fracture behavior in particle bed comminution. One reason for the diverse opinions in literature is that there are three types of particles after the comminution in the particle bed: ? Particles which are stressed below their breaking point, ? Particles which are stressed right up to the break point, and ? Particles which are stressed beyond their breaking point.

Sep 1, 2012

By R. ?. Sherembayeva, ?. ?. ?uktybayeva, ?. B. Rakhimbekova, N. ?. ?m?rova

"Studying the interaction of the phosphorus-containing flotation reagent with the components of the flotation system ""liquid-gas-solid"" during flotation of non-ferrous metal ores allows regulating the enrichment process. The phosphorus-containing reagent-collector anabasinium-O,O-dimethyl-thiophosphate has beensynthesized under laboratory conditions and the concentrated aqueous solution of anabasin hydrochloride and the 40% solution of sodium hydroxide have been used as the raw material. The phosphorus-containing reagent has been obtained by interaction of the anabasine base, sulfur and dimethyl phosphite, due to sulfur and nitrogen atoms it can form complex compounds with heavy metal ions.Studying flotation of copper-sulfide ore of the Sayak field with the use of the phosphorus-containing reagent-collector anabasinium has been performed in the open and closed cycles. The degree of ore grinding was 60- 62% of the class -0.074 mm. There has been established the dependence of the ore flotation parameters on: a) pH of the pulp; b) the consumption of the reagent-collector anabasinium.The effect of the pulp pH on the technological parameters of copper ore flotation has been carried out with a reagent regulator that increases the difference in the surface properties of the minerals to be separated.There has been used lime as the regulator of the medium, the consumption of which varied from 750 to 1500 g/t; the consumption of the reagent-collector anabasinium was 10, 15, 20 and 25 g/t.It has been found that when flotation of copper ore without the use of lime at pH equal to 7.8 and at the reagent consumption, g/t: anabasinium - 25, T-92 - 55, copper recovery in the concentrate is 92.72%, the quality of concentrate is 7, 1%.In flotation according to the factory mode (the consumption of xanthate is 44 g/t, T-92 is 55 g/t, pH = 7.8 (without lime)) of copper ore, copper recovery in the concentrate is 87.38%, the concentrate quality is 7, 97%, with reducing the xanthate consumption to 25 g/t copper recovery is reduced to 83.39%, the quality of the concentrate is up to 6.69%.In the experiments using the factory reagent mode in the closed cycle, with the xanthate mass consumption of 44 g/t, T-92 blowing agent of 55 g/t, the third recleaning concentrate contained 19.13% copper with recovery of 86.89%.Using a phosphorus-containing reagent instead of xanthate with the same flow rate, the third recleaning concentrate with the mass fraction of copper of 19.82% has beenobtained with recovery of 87.77%."

Jan 1, 2018

By S. Banisi, O. Farshid, M. R. Rozebehi, A. Bahar, A. Arghavani, M. Mahdavi

At the rougher flotation circuit of the Miduk copper concentration plant (Kerman, Iran) five column cells (CISA) with the diameter of 4m and height of 12m using static mixer type (MicrocelTM) spargers have been installed. Based on the initial design, columns should accept a feed rate of 625 t/h with 80% passing size of 90 µm and solids concentration of 28% and produce 88% of the plant concentrate (i.e., 22 t/h) containing 32% copper. Due to mechanical and processing problems this objective was never realized and theses columns were remained out of operation from the commissioning time (2005). A new attempt with the aim of returning these cells into operation started in 2013. The results of an extensive study indicated that spargers plugging due to the entrance of small amount (2 kg) of coarse particles (up to 2.5 cm) because of usual problems at the plant environment was the main reason of columns non functionality. With a change in the recycle pump inlet design to the column, which prevented the entrance of coarse particles to the spargers, the operation of the column significantly improved. It was found that in order to have a stable operation of the columns at the rougher stage the feed rate for each column should be reduced from 125 (design) to 70 t/h. The air superficial rate had to be also reduced from 1.9 (design) to 0.6 cm/s. A period of 10 days of continuous operation showed that the carrying capacity was 0.23 (g/min/cm2) which was significantly lower that of the design value (i.e., 0.58). The gas hold up was found to be lower than 10% beyond which columns started to move to the turbulent state indicated by "boiling" froth. The average life time of spargers was determined to be 20 days which considered to be very short. The average recovery and concentrate grade of these columns were found to be 68% and 32%, respectively. The high wear rates of spargers, unusually high level of maintenance and supervision needed and instability of the operation made the plant managers not to use column cells as the roughers.

Jan 1, 2014

By David Verrelli, Melissa Kistner, Leanne Smith, Chris Aldrich, Lidia Auret, Warren Bruckard

In this investigation, different mixtures of realgar and orpiment particles were floated in a laboratory batch flotation cell and multivariate image analysis was used to estimate the arsenic content in the froths. The analysis was based on the froth colour, as well as extraction of three groups of textural features, namely those based on grey level co-occurrence matrices (GLCMs), wavelets and local binary patterns (LBPs). Collectively, these features provided better information on the arsenic content of the froths than any one of the individual groups of features. Partial least squares models could explain approximately 78% of the variance in the arsenic by using all the features combined. The colour content, particularly the green component in the red-green-blue (RGB) features, provided almost as much information as each of the three sets of texture-base features individually.

Jan 1, 2014

By R. Kobialka

In the article results of experiments over jaws? linings in jaw crushers with different shaping of working surface were presented. Following sets of jaws were under investigation: immobile plain jaw and moving jaw with grooving surface. Grooving jaws have groves with circular, triangular and trapezoid cross section. In order to evaluate efficiency of comminution both the grain composition of product and the content of irregular grains were determined, as well as the size of crushing forces and process efficiency were measured. For the combination: plain jaw with grooved one, a good results were obtained as regards the grain composition of product and the content of irregular grains. Crushing forces were higher at crushing with mixed types of jaws (the one plain, the second grooved), in comparison to crushing with using both grooved jaws. Efficiency of the process was definitely higher for mixed jaws.

Jan 1, 2014

By Yuhua Wang, Haitao Zheng, Guangli Zhu, Yuehao Zhao, Fushun Yu, Dongfang Lu

"Spodumene, feldspar and quartz possess similar surface properties, which make the difficult to separate spodumene from other silicate minerals by flotation. The differences of crystal structure, surface property and floatability of three minerals were studied by various technical means. The results show that Li-O and Al-O bonds in spodumene structure are not strong and easy to be broken. However, Al-O and Si-O bonds in feldspar and Si-O bond in quartz are very strong and not easy to be broken. High contents of Al and Li on spodumene surface were found by XPS measurements, which is benefit for the adsorption of anionic collector. The surface energies of main cleavage planes of spodumene (110), feldspar (001) and quartz (001) are 1.88 J/m2, 2.97J/m2 and 2.68J/m2, respectively. Hence, the exposed surfaces of feldspar and quartz are not saturated and easy to adsorb OH- ions from solution and cause the lower IEP than spodumene. The contact angles of three minerals in water are lower than 16º, suggesting that the hydrophilicity of three minerals is high, and the order of hydrophilicity is quartz > feldspar >spodumene. Correspondingly, contact angles and flotation recoveries of spodumene are bigger than that of feldspar and quartz in presence of a combined anionic and cationic collector named YOA.INTRODUCTION Flotation technology plays most important role for the recovery of spodumene from pegmatite ore. Generally, spodumene with fresh surface is easy to be floated using soap and oleic acid as collector, and the best flotation pH range is 4.0 to 9.0. However, the flotability of spodumene will become worse when its surface was polluted by slime which produced by the weathering of spodumene and other silicates (Dresler et al. 1998; Moon and Fuerstenau 2003; Menéndez et al. 2004; Yu et al. 2015). In addition, the species of Ca2+, Fe3+, Mg2+ and other metal ions in pulp can not only activate the flotation of spodumene, but also the activation of gangue minerals, and then the flotation selectivity of spodumene from gangue minerals became wores (Wang and Yu 2007; Yu et al. 2014). In order to eliminate the negative effects of slime and metal ions on the flotation of spoddumene, the desliming and long time scrubbing with the addition of NaOH and Na2CO3 were adopted. Usually, NaOH shows the activation for spodumene flotation, and the recovery of spodumene increases with the increase of NaOH dosage. Na2CO3 can eliminate the non selective activation of Ca2+, Fe3+, Mg2+ ions in the pulp, and the concentrate grade of spodumene increases with the increase of Na2CO3 dosage. Anionic collectors such as chelants, hydroxamic acid, oxidized paraffin soap, naphthenic acid and oleic acid were widely used for the flotation of spodumene (Dresler et al. 1998; Moon and Fuerstenau 2003; Menéndez et al. 2004; Yu et al. 2015)."

Jan 1, 2018

By Bisweswar Das, Barada Mishra, Hrushikesh Sahoo, Swagat Rath

Banded hematite jasper (BHJ) containing 45.2% Fe, 32.64% SiO2, 0.63 % Al2O3 and 1.25 % LOI is found difficult to beneficiate either by magnetic or flotation techniques due to fine intergrowth of jasper with hematite. Phase transformation by reduction roasting with activated charcoal followed by low intensity magnetic separation to achieve a suitable iron concentrate has been attempted in this study. The mineralogy of the ore and different roasted products has been studied by X-ray powder diffraction (XRD) and scanning electron microscope (SEM) to understand the reduction mechanism. The magnetite formation is observed at 850ºC while metallic iron appeared at a higher temperature. The effects of reduction variables such as reduction time (30-270 min), temperature (750-1050ºC), and reductant (1-12 %) using activated charcoal are studied. An iron concentrate with 64.65% Fe and 55.8% recovery could be obtained under optimum conditions of temperature: 850ºC, time: 1.5 h, and reductant: 6% by weight.

Jan 1, 2014

By N. Acarkan

Slags usually contain some quantity of valuable metals. They are actually a secondary resource of metals, rather than an end-waste and have been utilized as a resource material in many areas. In addition, for some applications, slags have comparable or even better properties than their competitors. Leaching is a method for extraction of metals from copper slags. The extraction of metals such as copper and cobalt from the copper slag of Küre-Turkey, was investigated in the past decades. Fayalitic type of these copper slags containing 0.934 % Cu, 0.353 % Co and 50.91% Fe were subjected to the experimental study. As a result of mineralogical analysis of the slag sample, fayalitic type of slag was found to contain hercynite, magnetite, hematite, pyrite, chalcopyrite, covellite, bornite and metallic copper. Direct acid leaching methods were applied on the sample. Effects of leaching time, temperature and acid concentration on Cu and Co leaching recoveries were investigated in the direct acid leaching. The optimum leaching conditions were found as leaching time of 2 hours, solid/liquid ratio of 1/3, H2SO4 concentration of 125 g/L and temperature of 70 °C. At these conditions, 75.5 % of Cu, 95.6 % of Co and 70.9 % Fe were extracted. In the second stage of the leaching experiments, copper in the pregnant solution was precipitated by cementation to produce a Cu concentrate assaying 95.58 % Cu; cobalt was obtained by precipitation with H2S to produce a concentrate containing 62.10 % Co. As a result of this study a process flow sheet has been developed for recovering Cu and Co from these slags to demonstrate its economic and technological benefits.

Jan 1, 2014

By Y. M. Zhao

Reutilization of waste printed circuit boards (PCB) can not only prevent potential environmental pollution, but also achieve recycling of secondary resources. Study on recycling of discarded PCB belongs to the front edge of environmental pollution prevention and resource recycling. In order to effectively crushing waste PCB, and solve the problem of secondary pollution of fugitive odor and dust during the crushing process, a wet impacting crusher was adopted to achieve comminution liberation of PCB in water medium. 96.79% of the crushed yield was distributed in ?2mm, and metal took 97.18% in this grade of production. Size distribution of PCB particles was characterized double peaks at the sizes of ?1+0.5mm and ?0.074mm. A double Rosin-Rammler function, is called DRR function, is put forward to describe the size distribution of PCB particles. The DRR function of cumulative weight percentage oversize of PCB was non-liner fitted by self-defining DRR function of the Origin 7.0. The evaluation indexes of the fitting results are the correlation coefficients R2 of 0.9994 and residual E of 0.18671, those show that DRR function is perfectly accurate. Based on the research the mechanical separation and material properties of PCB, a wet process of reclaiming metals from PCB using a new style separator ? tapered diameter separation bed (TDSB) in water medium was designed, and the related separation mechanism was studied. The fluid field of the tapered diameter separation equipment was simulated by the Ansys Flotran software, the variation laws of the velocity in each position in the fluid field as well as the equation of axial distribution sectional max velocity were analysed according to the simulation result, the stress change and motion trajectory of the pellet in the certain fluid field were analysed. The results show that the expanding tubular structure of the varied diameter separation bed indicates gradually decreasing velocity of water flow along the axis, assuming a certain angle in the bed, as a result of the gravity?s influence, and there was corresponding change to the distribution of the flow velocity, thus the whole formed a special fluid field where velocity variations exist in different positions. When the material passed through the fluid field along with the water flow, as a result of the difference to the particle density, the granularity and the shape, there would appear the difference to the motion trajectory as well as the movement distance under the action of the fluid: The lower density materials discharge along with water flow, but the higher density materials would be kept in bottom of the bed and discharge through material mouth. Therefore, light and heavy products were separated effectively according to the density. Using tapered diameter separation bed to process the ?1mm size crushed material of waste printed circuit boards, with the discharge of water 5.5m3/h, feed-rate of the material 250g/min and with an obliquity 35°, product with 93.92% in integration efficiency and 93.73% in recovery ratio of the metal were obtained by the primary separation. Compared with other mechanical methods, the range of particle size was broaden using the TDSB to recovery metals from PCB, and lower limit size of separation almost approach to 0. An innovative process of ?wet impact crushing+ classifying+ tapered diameter separation? recycling metals from waste PCB was developed.

Jan 1, 2014

By Sarra Scherbakova, Alexander Kurkov, Andrey Egorov

"Deep concentration of iron ores involves extraction, in addition to magnetite concentrate, of hematite and martite concentrates and recovery of other valuable components. A flotation technology was designed specifically for finely disseminated hematite ore, allowing producing saleable hematite concentrate containing 64-66% Fe. The main process challenge is caused by the presence of other ferruginous minerals such as carbonates, silicates, and phosphates, and fine hematite and martite mostly concentrated in the -0.044 mm fraction. Main operations of the processing circuit are removal of slime, flotation to remove impurities (carbonates, phosphates etc.) with an anionic phosphorous collector in an alkaline environment, hematite and martite flotation using same collector in a slightly acidic environment to produce commercial iron concentrate. Tailings of wet magnetic separation of magnetite containing 24.5% Fe and finely disseminated hematite ore containing 51% Fe were processed to produce iron concentrates with a yield of 15% and 50%, respectively, containing approximately 65% Fe and 5% of silica. Hematite flotation tailings had the highest content of gold (up to 0.09 - 0.11 g/t), while in other products it never exceeded 0.02 g/t. Using a Knelson concentrator was able to recover 40 to 45% of the gold into 3.31 g/t Au gravity concentrate. The success of gravity concentration is due to high gravitational contrast of gold to mostly quartz and aluminosilicates in the hematite flotation tailings. In general, the proposed process can be used as a solution to the challenge of selective concentration of finely disseminated iron minerals."

Jan 1, 2014

Separation performance of a Floatex Density Separator (FDS) has been studied both experimentally and theoretically. Experimental results reveal that at a lower bed pressure the FDS acts like a classifier. Higher bed pressure is required to attain the concentration effect as proper development of suspension density occurs under these conditions. It is seen that the size or density alone is not able to describe the partition fully. The terminal settling velocity, which includes both the size as well as the density of the particle can be a useful descriptor of separation in a FDS. While a narrowly distributed feed offers better performance of a FDS, a wide size distribution of feed results in large scatter in the terminal settling velocity distribution and renders the separation difficult. The closely sized feed enhances the density effect in concentration. A higher teeter water flow rate also helps in carrying larger-lighter particles to the overflow by increasing the cut off terminal settling velocity as it increases the net upward force. A detailed description of separation performance in a Floatex Density Separator has also been established from theoretical considerations. Separation performance of the separator is described using a simple slip velocity model. The model has been validated com-paring the predicted FDS performance results with those experimentally measured under widely different operating conditions.

Jan 1, 2014

By B. Das

The processing of banded iron ore by direct anionic and reverse cationic flotation to produce pellet grade concentrate is investigated. This low-grade iron ore, known as banded hematite quartzite (BHQ) contains 41.8% Fe, 41.5% SiO2, 1.2% Al2O3, and 0.5% LOI. The flotation behavior of BHQ is studied by varying the effect of concentration of collector, frother, dispersant and pH. Oleic acid and dodecylamine are used as the anionic and cationic collectors respectively. The parameters that gave the best results in cell flotation are utilized in 100 mm diameter flotation column. All the results are compared with regard to the iron grade and recovery in concentrate. It is observed that, anionic collector with dispersant dosage of 220 g/ton, at pH ~8.5 is selective and yielded a high-grade iron concentrate with low silica as impurity. Also, it is possible to achieve an iron concentrate with 64% Fe at 30-37% weight recovery. The characterization studies of the BHQ ore using X-ray diffraction (XRD) technique and liberation analysis with QEMSCAN® are carried out. The sample contains 58.8% hematite and 37.7% quartz and the liberation of hematite particles are found to be 90.3% in -25 µm size. An alternative statistical modeling approach called response surface methodology was also undertaken to optimize the operating parameters in order to maximize the iron grade and recovery. The predicted results by the model are in agreement with the experimental values.

Sep 1, 2012

By H. Z. Kuyumcu

Coking of coal blends using high volatile coals with poor coking abilities to produce a high quality coke for blast furnace application can be achieved by compacting the coal blend prior to the carbonization process. Here densification up to a relative material density of 80 %, i.e. a compact density around 1100 kg/m3, has proven to be advantageous. Coal is compacted by stamping, if the so-called stamp charging process applied. Compacting of the coal by pressing is practised in case of the cokemaking with so-called heat-recovery ovens. Stamped and pressed coal cakes require over the cake volume uniform high density and mechanical stability. Besides the aspects of the coal selection, the efficiency of the process is mainly determined by the operating parameters compacting time and compacting energy for coal cake making. At the Department for Mechanical Process Engineering & Solids Processing of the Technical University Berlin the two sub-processes of densification and strengthening during stamping and during pressing are theoretically and experimentally investigated using specially developed lab-scale compacting test units and a strength test device. Describing cake density in terms of coal properties for a given coal and measured compacting energy input then leads to a compacting equation with the so-called Stampability as the integral model parameter for the stamping process. For the pressing process the cake density can be calculated with the measured compacting pressure and the Compressibility factor, respectively. Investigations were carried out to provide evidence of a significant influence of coal type, coal surface moisture, coal granulometric and mechanical properties on the densification process. The overall objective of the work is to establish a comprehensive mathematical model on the compacting behavior of large coal bulk quantities and the optimization of the compacting processes by stamping and by pressing. Keywords: coal compacting, agglomeration, stamping, pressing, cokemaking

Sep 1, 2012

By S. F. Ye, L. Xiao, Y. L. Wang, P. W. Han

"Copper anode slime is a precious secondary source for the recovery of silver. However, current recovery process are constrained by either sever pollution or high cost. To cover the drawbacks of current process, this research employed a novel strategy by using the manganese dioxide as the oxidant in acid solution, which avoided the generation of sulfur dioxide while high silver extraction rate was achieved. The effects of manganese dioxide, sulfur acid concentration, stirring speed, temperature and leaching time on silver extraction rate were investigated. The silver recovery reached to 91.68% under the conditions of 1.2 g manganese, 2.0 mol/L H2SO4, 300 rpm, 80 °C and 6 h. INTRODUCTION Copper anode slime is generated from the electrolysis refining of copper and is extremely precious for its containing noble metal such as silver (Chatterjee, 1996; Amer, 2003; Yldrm et al., 2014; Syed, 2016; Wang et al., 2017). Therefore it is of great significance to extract silver from anode slime for the full utilization of resource. Pyrometallurgy is the most mature process for the extraction of silver because of its stability and adaptability (Hait et al., 2009; Zhao et al., 2010; Gao et al., 2017). However, it also suffers the drawbacks of high operating cost, low extraction rate of silver and severe pollution of smoke dust (usually containing lead and arsenic) (Ludvigsson and Larsson, 2003). To cover the drawbacks of pyrometallurgy process, more and more attentions are giving to the semi-hydrometallurgy process which usually includes a pretreatment process of sulphatising roast or low temperature oxidizing roasting (Tishchenko, 1964). After pretreatment, the refractory silver bearing phases (silver selenide, silver sulfide and silver) are converted into readily leached forms which are often extracted by ammonia, sodium sulfite in alkaline solution (Valiuniene et al., 2010; Wojciech, and Kitka, 2017). Despite its relatively high extraction rate and low investment, it still has the disadvantages of releasing harmful gases since the sulfur dioxide are generally generated in the pretreatment process. In addition, the use of ammonia can easily lead to a leaking into the atmosphere once not carefully dealt with (Aylmore and Muir, 2001). As for silver recovery by sulfite leaching, the consumption of sodium sulfite is rather high which often results in a pipe blocked (Yang et al., 2006)."

Jan 1, 2018

By Junwei Han, Wenhua Li, Wenqing Qin, Fen Jiao, Wei Liu, Jiaqi Xu

"A novel technology was developed to study the process of recycling copper from waste printed circuit boards (WPCBs), which are the main source of metal production in the next decades. The chemical compositions of the WPCBs were investigated. The results indicated that the PCB powder was mainly composed of copper (38.5 wt.%), iron, aluminum, and non-metallic materials. Copper is mainly in the form of Cu and is the most valuable metal for the recycle of WPCBs. The concentrated WPCBs powder, obtained by the mechanical process, were pressed as the anode, which was directly electrolyzed to produce copper. The effects of H2SO4 concentration, Cu2+ concentration, current density, pole pitch, and liquid-to-solid ratio on the voltage, current efficiency, and copper extraction were investigated. The results indicated that the optimum conditions were liquid-to-solid ratio of 30 mL/g, current density of 571 A/m2, sulfuric acid concentration of 180 g/L, 50 g/L of copper ion, polar distance of 3 cm. Under the conditions, a desired current efficiency could be achieved. Meanwhile, about 95.62% Cu was recovered from the WPCBs. The experimental studies also revealed that the purity of copper obtained at the highest current efficiency was higher to 99.98%. Produced copper sheet were characterized by X-ray diffraction (XRD). XRD analysis indicated that the copper was the main phase. INTRODUCTION With the rapid development of electronic industry, more and more waste electronic and electrical equipments (WEEE) are generated every year (Fogarasi et al., 2012; Liang et al., 2013). The production of printed circuit boards (PCBs) is the base of electronic industry, because it is the essential part of all electrical and electronic equipments (Schlummer et al., 2007). As a result, a considerable amount of waste PCBs containing plenty of heavy metals have to be treated. In general, PCBs contain about 28% metals that are abundant non-ferrous metals such as Cu, Pb, and Sn. Printed circuit boards can be considered as a secondary resource for recycling rather than wasting. The contents of gold and silver respectively reach 80 g/t and 3300 g/t, which are much higher than that of primary ores. Copper is the main metal of PCB and its content is as high as 26.8% ( Zhang et al., 2009)."

Jan 1, 2018