Search Documents

By Fiona Sofra, Briony C. Ruse, David B. Boger

"The sustainability of the mining industry must be addressed through improving tailings management. The use of thickened tailings and pastes stems from a paradigm shift towards designing tailings disposal sites to suit their surrounding environment, rather than manipulating the environment to accommodate the tailings. Thickened tailings and pastes usually exhibit non-Newtonian behaviour, so a thorough understanding of the rheological characteristics of the material is required in order to determine the disposal plant operating conditions.Full Cost Accounting techniques may be used to provide financial justification for the implementation of alternative tailings disposal techniques through the calculation of a disposal cost per tonne of tailings over the life of the facility. Improved disposal methods such as thickened tailings disposal involve additional initial capital expenditure but reduce environmental impacts. The cost savings associated with environmental impact mitigation are reflected in Full Cost Accounting outcomes.Rheological characterisation is significant as a design basis that may be analysed using Full Cost Accounting to justify the initial capital expenditure of dry disposal systems for improved environmental performance."

Jan 1, 2003

By Cheng Gan, Gui Xiahui, Li Shulei, Cao Yijun, Liu Jiongtian, Wu Lun

Flotation rate constant is an essential parameter in the flotation process. The fine coal sample utilized in this investigation is anthracite from the Shenhuo mine in eastern China. Fine coal flotation rate tests were conducted to compare the flotation rate constant at constant power input with that at gradually increasing power input. Results indicate that the flotation rate constant decreases with the flotation process and increases as the flotation energy is increased. In addition, the flotation rate constant is close to the maximum value. The increasing trend of the flotation rate constant gradually slows down as the flotation energy input increases.

Jan 1, 2014

By Braulio Fernández, Gonzalo Montes-Atenas

The mechanisms taking place during the leaching of chalcopyrite when it is in contact with other sulphide minerals, particularly pyrite, is still a matter not fully solved. The GalvanoxTM process has been suggested as a technical solution to extract copper from chalcopyrite at commercial level inhibiting passivation phenomena widely reported in the field of hydrometallurgy. Although there are some rules of thumb to implement the process in fully flooded stirred conditions such as the optimum pyrite/chalcopyrite mass ratio should range between 2 and 4, among others; not many research studies have been focused on studying the effect of the surface contact area between chalcopyrite and pyrite to reach best copper extraction conditions. The aim of this research work is to determine the effect of the mass and surface area ratio between the minerals and the surface area of each of the mineral species effectively exposed to the leaching solution. Different particle size distributions of pure pyrite and chalcopyrite were contacted in a small column and subjected to leach tests using sulphuric acid in concentrations close those used in industrial leaching processes. The mass and surface area ratios which optimize the extraction of copper were obtained. It was found the best leaching conditions were attained when reducing the particle size distribution of pyrite regardless the particle size distribution of chalcopyrite. Further analysis concerning the impact of this conclusions on large scale operations is presented and discussed.

Jan 1, 2014

By Megha Patel

"The objective of this project was to investigate the application of Prompt Gamma Neutron Activation Analysis (PGNAA) technology to provide real-time on-belt elemental analysis of feed ore in base metal sulphide processing, in this case at the Mount Isa Mines Zinc-Lead Concentrator Heavy Medium Plant (HMP). After initial exploratory testwork proved successful, a Geoscan On-Belt Elemental Analyser was retrofitted onto the existing HMP feed conveyor. Dynamic calibration of the Geoscan was conducted based on laboratory XRF analysis results of the HMP feed conveyor hammer autosampler samples from May to November 2013. Comparison of the Geoscan results to the laboratory XRF analysis results during and after dynamic calibration indicated the technology had acceptable accuracy to be incorporated into HMP process control. The variation between the two sets of data includes all primary sampling, sample preparation and XRF analysis errors as well as the Geoscan errors themselves. The Geoscan instrument precision must be calculated separately through a duplicate sampling campaign and independent laboratory analysis before extending the scope of its range of application beyond HMP process control. The expected benefits of integrating the Geoscan real-time data into HMP process control are optimised HMP metal recovery, improved cost efficiency and improved stability of the downstream processes (milling and flotation). Utilisation of the Geoscan will also enable improved feedback to mines on grade control and dilution, and provide additional information on individual ore types when fed as campaigns to HMP."

Jan 1, 2014

By Jan Cilliers

The demand for minerals has never been higher. Moreover, the rate at which this demand is growing is unprecedented, and expansions and new mines will be required to fulfill these growing needs. This, in turn requires a skilled engineering workforce that can develop and operate minerals extraction processes to utilise effectively more complex ores. The International Mineral Processing Council (IMPC) has established a Commission on Mineral Processing Education to consider the global challenge of ensuring an adequate supply of well-trained mineral processing engineers. The Commission has, for the past four years, been collecting international information of the recent mineral process engineering supply position and with a view into the near future. The data collected by the international Commission members are as follows: ? Undergraduate student numbers in minerals engineering ? A breakdown of their male/female ratio ? The fraction of the students from each course that enter the minerals industry ? Teaching staff numbers and age profile This data has been collated and analysed, and the findings are presented. It is clear from the analysis that the supply situation is very different in different regions of the world, and that great opportunities exist for targeted recruitment into the industry to meet the future talent demand. Further, an attempt at correlate the supply of minerals engineers based on the local mineral production rate is shown, which shows that there are clear outliers.

Sep 1, 2012

By V. Z. Kozin, E. A. Bekchurina, P. S. Volkov, Yu. P. Morozov, A. S. Komlev

"The current sampling systems of ore flows or concentrates are based on the method of cross sections in point sampling and the method of scooping in reducing. The limited number of point samples in sampling and microsamples in reducing lead to big random and probable systematic errors. The paper defines the principles of sampling, which assure the absence of systematic errors and also provides calculation formulas of probable errors in sampling methods of cross and longitudinal sections as well as in samples preparation. The article sets the fundamental laws of sampling: the dependency of minimal mass of gross sample and number of point samples from mass of point sample in sampling from heterogeneous body; the dependency of a sample minimal mass from lumps’ size in preparation of carefully mixed samples; the dependency of point samples’ dispersion from duration of control period. The paper introduces the fundamental notions: lump variance; probable systematic error; methodical error. It also provides a solution of outstanding sample correct application in analysis results calculations. In application of automatic analyzers, mounted in material flows, the probable error connected with sampling, is calculated by the formulas for carefully mixed sampling bodies. The paper describes the developed and introduced sampling systems on the base of combined application of cross and longitudinal sections methods in sampling and preparation of samples. The advantages of this equipment are compactness, reliability, simplicity in service and operation, and for pulps it is adaptability in pipelines. Application of the developed equipment entirely excludes probable systematic error. The new systems of sampling and preparation of samples are introduced at 25 concentrating plants. Introduction of the developed systems at sampling balance points of concentrating plants allowed double reducing balance deficiency."

Jan 1, 2018

By Pamela Castillo, Marcia Muñoz, Rodrigo Luca, Brian Townley, Fernando López

In the present study we discuss the value of multi-element geochemistry as a tool for semi-quantitative to quantitative bulk mineral characterization in geological and geo-metallurgical modeling of porphyry copper type deposits, with an emphasis on hydrothermal alteration associations, types and intensities. In mine production of porphyry copper deposits much effort is placed on ore grade and geological modeling, applied for predictive mineral processing behavior, from blasting, grinding, leaching or flotation, down to waste disposal and environmental management. High confidence geological models are commonly based on geological mapping of drill core and surface/ underground exposures, combined with discrete mineral characterization (e.g., petrography, QEMSCAN®, spectroscopy, etc.). Unfortunately these are expensive and applied to limited numbers of samples, thus lacking sufficient representation and not suitable for geo-statistical modeling. In addition, geological mapping always presents uncertainty, based mostly on qualitative estimates. The combination of information usually provides geological models that are hard to combine with geo-metallurgical data, much less with mineral processing predictive behavior models. The advent of multi-element geochemistry, at low cost, has allowed employment of such tools massively, yet little use is given to the data, usually focused on elements of economic interest (main ore and credits) and elements of negative impact to concentrates and/or process. Geochemistry reflects the mineral composition of rocks, thus allowing characterization of lithology, alteration types and intensities, and mineralization. As examples of such applications we present generic classification techniques which were developed on various porphyry copper deposits of northern Chile, these based on multi-element geochemistry, allowing for semi-quantitative to quantitative high resolution modeling of key aspects of lithology, hydrothermal alteration and mineralization, and which may be cross-referenced to metallurgical test samples and by that, to geo-metallurgical properties of rocks and modeling. In addition, as data is quantitative and continuous, modelling of gangue can benefit from geo-statistical modeling.

Jan 1, 2018

By E. Hulthén

Crushing plants are widely used around the world as a pre-processing step in the mineral and mining industries and as standalone processing plants in the aggregates industry. Despite automation and different advanced model predictive control, a lot of the process is still managed by operators. The operators affect a lot of the performance. The numbers of the improvement they can achieve are at least as big as the advanced control algorithms?, today. Therefore, it is also important to train the operators so they know how to behave in different situations. Models for crushers and other production units have been developed during the years and the latest add is the different units? dynamic behavior being brought in, which gives the crushing plants dynamic time dependant performance. This can be used as a simulator for operators training. By connecting a Human Machine Interface (HMI) to a dynamic simulator with the models incorporated, a training environment for operators can be achieved. In this paper, a dynamic crushing plant simulator implemented in MATLAB/SIMULINK has been connected to an HMI via a PLC. The HMI is placed in a control room at the university and complemented with monitors showing sequences from the process connected to the simulations, thus creating a realistic control room for training. In the created training environment, the operators can be trained under realistic conditions. Simple training scenarios and how they could be simulated are discussed. Apart from the increased level of knowledge and experience among the operators, the time is an important factor. While a real crushing plant is still being built, the operators to be can already be trained, saving a lot of the commissioning time. Keywords: crushing, cone crusher, simulator, control room, operator, training

Sep 1, 2012

By Jorge Misle, Daniel Silva

"This paper addresses the need for advanced control technologies and strategies in the mining industry, its potential and actual impact on mining processes and the best practices for their implementation, operation, and long term sustainability. It is well known that advanced process control (APC) can be a very good source for incremental process improvement for the mining industry, yielding to higher production rates or helping maintain consistent production rates despite ore changes. The application and integration of new technology, process knowledge and innovation are key elements in building such a supporting structure. More specifically, and this cannot be emphasized enough, the correct application and assembly of control tools, the in-time presentation of key data to decision makers and the development of relevant statistics and KPI’s (key performance indicators) can and will make a difference not only in terms of production, but also in plant stability, availability and production costs. In deploying such ideas and aiming at the long-term goal of "Operational Excellence", Minera Los Pelambres (MLP) has developed a number of successful control strategies, best practices and technologies, which are not only the application of state-of-the-art automation and computing tools, but rather the assembly of the above presented structuring factors. This work discusses some of the key tools and ideas implemented for SAG & Ball milling and Flotation areas, their performance results and the roadmap taken for the integration of process knowledge and control tools. Also, cases studies are presented and discussed further to not only show the main areas of improvement, but also to highlight the benefits of such strategy that for the most part, deviate from the traditional mining industry control approach. Also, a word is given on the need for innovating in the design of control strategies and leveraging best practices and process knowledge that ultimately, will contribute to long-term reliable operations, improved mineral processing and, although unmeasured, lead to a superior overall performance and productivity of all mining personnel involved."

Jan 1, 2014

By Brochot. Stephane, Manuel Gonzalez Fernandez

"HPGR (High-Pressure Grinding Rolls) is widely used today for grinding of various kinds of ores such as iron ore or base and precious metal ores. It can be used as first stage of grinding replacing tertiary crusher and SAG mill, but also as regrinding stage to enhance mineral liberation. In addition to better energy efficiency, the advantage of HPGR is to produce much more internal particle fractures allowing faster leaching as it has been demonstrated for some gold ores. This grinding mode of compression and fracture generation also promotes mineral liberation without overgrinding. Mineral processing modelling and simulation associated to detailed ore characterization constitute a powerful tool for plant design and optimization. The mathematical models of the units of operations (grinding and separation) have to reproduce the mineral deportment for which the mineral liberation plays a central role. The present paper is focused on the HPGR modelling with the objective of plant optimization or advanced design from pilot plant tests. The traditional approach of the population balance linked to the energy dissipation and the residence time distribution is generalized in association with a mineral liberation model. The effect of the specific HPGR breakage matrix and grinding function on the mineral liberation rate is discussed and compared to the tumbling mill. The implementation of this mathematical model into a plant simulation tool is illustrated by the example of the optimization of an iron ore concentrator."

Jan 1, 2014

By M. Brennan, A. Majumder

"The mineral processing research community has devoted enormous efforts to the modelling of mineral separators over the last 50 years. While many efforts have been made to use only fundamental physics as a basis for the models, fluid flow patterns in separators are not simple while the motion of particle swarms through fluids is extremely complex.One of the simplest separators is the sluice, in which separation takes place in a flowing film a few millimetres thick. The particles are suspended by turbulent eddies and motion relative to the fluid takes place in so-called hindered settling mode.In an effort to test the extent to which fundamental fluid mechanics can provide a prediction of particle separation, a study on a simple parallel-sided sluice has been carried out using glass beads at various particle concentrations and flow rates.The actual particle separation taking place was compared to predictions made by first describing the fluid flow by a modified ‘law of the wall’ model.Particle concentration distributions were described using Hunt’s sediment transport model, assuming the particle eddy diffusion coefficient to be the same as that for the water. Settling velocities were calculated using either the Richardson and Zaki or Brauer and Thiele models. The latter takes into account particle size and density distributions and solids volumetric concentration.The resulting predictions of particle separation are remarkably good, even though the model does not model the local settling velocity in the slurry."

Jan 1, 2003

By Pawel Strzalkowski, Marta Baszczynska, Urszula Kazmierczak

The paper presents issues related to interference of mining activities with the environment. Exploitation of mineral resources causes primarily a modification of the landscape. All of the negative impacts on environment are short-lived and last as much as it takes to exploit the raw material. After the mine closure reclamation is necessary during which all aspects that reduce harmful effects of the mining activities on the environment must be taken into account. Current ways of reclamation allow recreating natural environment, which is different from the original and enriched in diverse new values. This requires propositions of new forms of converted land development through a detailed analysis of technical, natural, planning, economic and social sphere requirements. Before making final decisions regarding selection of direction of reclamation, a thorough analysis of the key factors has to be carried out. All steps related to the implementation of the reclamation project are shown in the paper using Limestone Mine "Górazdze" located in the south-western part of Poland as an example. This paper also presents an analysis of current ways of post-mining reclamation towards agricultural and forestry landscape, along with our own suggestion for their extension in order to preserve biodiversity. For choosing optimal solutions the most relevant criteria were considered: existing natural values and possibility of their protection. Taking into account the economic and social aspects, supported by natural potentials, implementation of tourism and recreation in this area were proposed. It was shown that this proposition would not interfere with the current trends of the natural landscaping. Finally, after completion of reclamation and land development in the considered mine area, creation of a geo-park was proposed along with appearance of geotourism in the area. To illustrate the proposed forms of post-mining land development in the form of maps, an ArcGIS(ESRI) software was used.

Jan 1, 2014

By E. Lee

Cone crushers are widely used within the mining and aggregate industries for the size reduction of minerals, ores, and rock materials. In mining applications for example, the product from cone crushers is often fed to HPGRs or directly to mills in the subsequent grinding circuit. An improved cone crusher performance can therefore result in an overall improved and more efficient comminution process. The objective of this paper is to systematically study a number of different ways of applying compressive crushing. By mathematically modelling these different crushing concepts and then theoretically optimizing crushing sequences accordingly, each concept can be studied and evaluated. In addition, aspects concerning whether or not the results are mechanically or practically achievable are considered. This study thus explores the advantages and disadvantages of different crushing concepts. In this paper, four different theoretical crushing concepts are presented and studied. The results show that in terms of interparticle crushing, optimal crushing sequences with varying compression ratios can be replaced by easier implemented series of constant compressions without significant deterioration. It is also shown that that considerably better performance is obtained for crushing sequences with both breakage modes. The subsequent comparison between such concepts indicates that different approaches can achieve the same results, and that the different concepts are comparable. It is further concluded that interparticle crushing should be kept to a minimum if fines generation or energy consumption is to be minimized, and that each of the studied concepts presents different challenges for implementation. Keywords: compressive crushing, cone crusher, optimization, modeling, crushing concept

Sep 1, 2012

By Christian O’Keefe, Alex Van der Spek

"Evaluation of inequalities of the partial sums defining cumulative grade and recovery prove that cumulative grade has an upper bound not dependent on the bank number and cumulative recovery possesses an upper bound proportional to the bank number. This explains one observed characteristic of cumulative grade versus cumulative recovery curves. The existence of such maxima combined with the observed shape of cumulative grade-recovery curves leads us to postulate that these curves can be well described by rectangular hyperbolae. Rectangular hyperbolae are characterized by asymptotes at right angles to each other. It is proven that this property can be used to derive an equation for the cumulative mass flow of the concentrate in terms of the asymptotic values of cumulative grade and cumulative recovery. Fitting hyperbolae to experimental cumulative grade cumulative recovery plant data then results in estimates of the maximum grade, the maximum recovery and a constant which may be taken as a performance coefficient of a row. Normalization of the cumulative grade and the cumulative recovery by their respective maxima gives rise to a graphical representation that can be used to evaluate the operating performance of a row of floatation bank cells. The normalization procedure removes the bias that is introduced by inevitable variation in mass flow of the feed and variation in feed mineralogy or feed particle size distribution. Reduction of the normalized data collapses all cumulative grade-recovery data onto one and the same curve. This removes the differences caused by the variation in row performance. The reduced cumulative grade-recovery data scatters around a common hyperbola. This can be used to gauge the validity of the assumptions made. Normalized cumulative mass pull is determined from the fitted values of the maximum recovery and maximum grade. This may serve as an alternative performance indicator of the floatation row."

Jan 1, 2014

By Claudio Bisso, Javier Vargas, Charles Lozano

"This paper summarizes the activities performed to predict SAG milling throughput at Minera Esperanza. Having highly reliable geometallurgical models aided by the new computer tools and specific metallurgical testing to rely on has become a major issue in recent times due to their impact on the business. Minera Esperanza’s SAG throughput model was constructed by characterizing the ore feed and operational parameters of the plant. Producing a robust model required satisfying number of requirements for the parameters used for both the ore and the plant as follow: 1) geologic and geometallurgical characterization parameters; and 2) parameters of a plant running at the rated production under optimum operating conditions. Obtaining these parameters required increasing the quantity of samples and metallurgical testing through drilling campaigns, mapping the drill holes and putting samples through various comminution tests while sampling all operational flows at the plant to obtain the metallurgical information for the operational parameters. The information was entered on the JKSimMet software to enable a throughput model to be developed to output SAG mill throughput predictions that are very close to actual throughput figures, i.e., accurate within a range of 2% on a monthly basis."

Jan 1, 2014

By V. Yu. Ivanov, A. I. Yuryev, L. S. Lesnikova, M. S. Datsiev

"The Talnakh Concentrator was put into operation in 1981 using a direct selective process to produce copper, nickel and pyrrhotite concentrates.In 2001, a novel selective-bulk-selective (SBS) technology for the concentration of massive sulfide ore was implemented, that allowed to increase the valuable components recovery into target concentrates with feedstock grinding coarser than before. In 2003-2005, the process upgrading included the differentiated processing of nickelpyrrhotite products recovered at the different concentration stages and made it possible to significantly enhance the contrast of the pentlandite and pyrrhotite flotation properties and to simultaneously increase separation of polymineral intergrowths.The next stage of the PD concentration complex development is the Project ""Talnakh Concentrator Reconstruction and Technical Upgrading"" to raise its capacity by half. The project has three Phases.• Phase 1. Pilot startup was carried out in January 2015 following the installation of new OK-100 TC flotation machines, manufactured by Outotec.• Phase 2. The introduction of a new technology developed by the Polar Division specialists launched in mid-2016. The new technology is based on maximization of iron and sulfur removal into tailings and maintenance of non-ferrous and precious metals losses at the same level.After the realization of Phase 3, the annual capacity of the Talnakh Concentrator will raise by another ~ 40% at the expense of processing cuprous and disseminated ores currently being processed by the Norilsk Concentrator.By 2023, due to upgrading of the PD production facilities the emissions to the atmosphere will reduce by 75%.Polar Division of PJSC MMC Norilsk Nickel (PD) searches for the ways to solve its environmental issues. Thus, in 2016, the Nickel Plant was shutdown and a new flowsheet was introduced at Talnakh Concentrator. It resulted in the reduction of sulfur specific amount sent to pyrometallurgical processing as a component of the concentrates.The Talnakh Concentrator was put into operation in 1981 using a direct selective process to produce copper, nickel and pyrrhotite concentrates.In 1981, its design capacity for processing of Cu-Ni ores from Oktyabrsky and Taimyrsky Mines did not exceed 3 million tons per year.In 2001, a novel selective-bulk-selective (SBS) technology for the concentration of massive sulfide ore was implemented at the Talnakh Concentrator, that allowed to increase the valuable components recovery into target concentrates with feedstock grinding coarser than before."

Jan 1, 2018

By I. Yu. Rasskazov, A. V. Rasskazova, N. M. Litvinova, N. A. Lavrik, V. G. Kryukov

The possibility of the intensification of the gravity processing of complex iron-manganese ore, which contains the finely dispersed inclusions of gold and platinum is shown. Clear mineral fractions of precious metals were sorted out of the different types of ores (quartz-braunite and carbonate- magnetite ore, ferruginous quartzite, carbon-containing shale, breccia-limestone and dolomite breccia). Composition and structures of precious-metals particles was detailed. The industrial content of platinum and gold was found. Precious-metals mineralization is character for all types of ores. High content of platinum is indicated in the carbonate-magnetite (up to 11.3 mg/kg) and quartz –braunite (up to 10 mg/kg) types of ore. Gold is presented in the ferruginous quartzite (up to 1.29 mg/kg) according to the data of the reduced mineralogical analysis. The composition of native platinum depends on the type of the ores: 1) quartz-braunite type contains isoferroplatinum (Pt3Fe) with Cu, Rh, Ir, Ru; 2) carbonate-magnetite type contains isoferroplatinum with Cu, Sn, Ni, Rh, Ir, Os; 3) pyritic-carbon ore contains isoferroplatinum with Sn, Ni; 4) ferruginous quartzite contains isoferroplatinum without admixtures. The ultrasonic treatment of mineral aggregates (P = 41.5 Watt, I = 15 W/cm2) made possible the liberation of fine particles of precious metals. Smooth-shaped or crystalline mineral aggregates are effectively liberated after acoustic treatment. Their surface is freed from impurities. The aggregates with the complex form and structure, which consist of the numerous plates and the grains, are not effectively liberated from impurities. It is shown that the ultrasonic treatment of aggregates with the fine inclusions of precious metals contributes to the liberation of the particles of platinum and gold and intensification of the gravity processing of refractory ore. This approach contributes the increase of the raw-material base of precious metals.

Jan 1, 2018

By V. F. Bannikov, A. P. Kozlov

"The purpose of this study was to develop a theoretical and technology framework for designing new combined technologies for processing tailings containing non-ferrous and noble metals using dry separation. The main goals of the study were: identifying the distribution patterns of valuable components in various fractions in dry separation processes; examining the patterns identified for different types of non-ferrous and noble metal tailings; developing a theoretical and technology foundation for the development of innovative technologies for the efficient processing of tailings with minimal process water consumption. To examine the possibility of efficient recovery of valuable components from refractory tailings using dry separation, an experimental laboratory unit was designed and built, composed of novel or modified lab equipment: plasma unit for increasing the magnetic susceptibility of Fe - containing minerals; magnetic separator supporting isodynamic and polygradient fields; pneumatic separator for the dry separation of finely dispersed mineral mixtures; dielectric separator using the resonant frequency of the electric field. The laboratory unit supports various modifications and combinations of the lab equipment. The experimental studies led to the development of a unified process scheme for lab tests of mature and non-ferrous smelter tailings using dry separation methods.INTRODUCTION The huge amount of waste from mining and processing of mineral resources Russia inherited from the extensive use of mineral resources in the Soviet Union and amount of waste continue to grow. Often the content of valuable non - ferrous, rare and noble metals in waste exceeds the balance contents in natural ores of the developed deposits. The availability of a rich scientific reserve for the creation highly effective innovative technologies for waste processing determines the necessity of the acceleration in the resolution of problems of the complex assessment, capitalization and involvement in the processing of technogenic resources in Russia (Chanturiya and Kozlov, 2014.)."

Jan 1, 2018

By E. Ashirbaeva

"Ores of ferrous metals traditionally make up the bulk of recoverable reserves of solid minerals, and iron ore concentrates - in the processing and consumption. To obtain concentrates, three main methods are used: dry and wet magnetic separation, gravity and flotation. But even their integration into complex developed schemes with finishing operations often do not solve the problem of obtaining high-quality concentrates, which are necessary for powder metallurgy and electric steelmaking. Increasing the iron content in the concentrate by removing harmful impurities is the goal of this work. The possibility of reducing the operations of wet magnetic separation twice and completely eliminating concentrating operations in ball mills from the scheme of operations has been established. Selective leaching agents for each type of iron ores have been created, allowing to obtain concentrates with an iron content of not less than 68-69% and negligible concentrations of harmful impurities. Methodical recommendations for long-term storage of bioreagents in the active state, their immobilization and preparation in industrial conditions at the enterprise Nedropolzovatelja are developed. The proposed biotechnology, which allows to obtain high quality iron and conditional concentrates for harmful impurities, is protected by patents (RU 2537684 ""Method for fine-tuning of high-sulfur magnetite concentrate"" for magnetite ores and Pat. RU 2599068. For the industrial implementation of the new technology, organizational and technological measures have been developed in the system with Road maps for types of ores. The developed technology makes it possible to condition noble metal, tin, tungsten, nickel and other concentrates in harmful impurities such as arsenic, antimony, mercury, sulfur, copper, zinc, iron, phosphorus, manganese, in total 30 components that pass into solution under the influence of bioreagents.INTRODUCTION Consumption of various metals is steadily increasing every year, the volume of mining is constantly increasing. Ores of ferrous metals traditionally make up the bulk of the recoverable reserves of solid minerals. Enrichment technologies for iron-containing ores are reduced to the combination of three main methods: wet and dry magnetic separation, gravity and flotation. But even the use of complex advanced technological schemes often does not lead to the production of high-quality concentrates suitable for metallurgical processing. In this case, either lapping operations or effective technical and technological solutions are used in the main enrichment cycle. Widely used in practice methods for improving the quality of iron ore concentrates include the use of finishing operations (fine screening, reverse cation flotation), staging of concentrates, the use of more sophisticated equipment (separators with running magnetic field, magnetic gravity classifiers, column flotation machines)."

Jan 1, 2018

By Yuri L. Nikolaev

The treatment of placer gold with fine gold, associated with gold-bearing sulfide minerals, heavy minerals and oxidized minerals such as manganowolframite (gubnerite) is not an easy task. In this case, this complex material cannot be treated using physical separation methods such as deep concentration and finishing, magnetic separation and solvent extraction. This technology is usually employed in gold washings finishing plant. The easiest way to recover precious metals in the form of an easy-to-sample saleable product is metallurgical treatment. This paper describes the application of pyrometallurgical processes with oxidative roasting, re-cleaning of cinders (if required) and ore-thermal smelting for producing gold bullion. Hydrometallurgical treatment of slags as an additional operation is recommended in order to maximize recovery of valuable metals. After this treatment, a barren leaching cake rich in PGM can be sold in the market. PGM can be collected as gold-silver alloy during smelting which allows the phase formation of polymetallic matte due to specific composition of fluxes. The PGM are then in the form of saleable gold bullions in the refinery.

Sep 1, 2012