Search Documents

By lves Matiolo, Jorge Rubio, Carlos Perez Guerrero, Denise G. Nunes, Fabiano Capponi

The problem (very old) of processing by flotation, the fine (“F”, 38-13 µm) and ultrafines (“UF”, < 13 µm) mineral particles continues to be a major technical challenge in the area of mineral processing. Many different processes have been proposed over the last three decades but, unfortunately, most of them have not found practical applications yet. This paper describes some advances in flotation research in fines (“F”, 38-13 µm) and ultrafines (“UF”, < 13 µm) mineral recovery by two different techniques. Extender flotation (EF) and flotation with bubbles with a wide size distribution-SB of copper sulphide ore fines (1 % Cu) were compared with a “standardised” (STD) mill laboratory procedure. Comparative evaluation was made through concentrate grade and recovery (size by size results included), “true” flotation recoveries and process kinetics. Copper porphyry samples, containing about 1/3 of the mass and about 37 % of the total copper content in the fines and ultrafines fractions were used. In the EF tests diesel-in-water emulsions were used as an extra reagent, added after the collector and frother addition. In SB tests, drawing air through an aspiration nozzle, directly in the pulp, generated bubbles sized about 50-200 µm. Both techniques yielded higher metallurgical efficiencies than the mill standard but better results were obtained with the extender flotation, with emulsified diesel oil (90 gt-1). Concentrate recoveries were of the order of 85-90 % (84 % in standard conditions), 14-17 % Cu grade (15 % Cu in the standard) and 3.5-4.5 min-1 for the Klimpel rate constant (3 min-1 in the standard). Size by size and true flotation results proved that metallurgical and kinetic gains, obtained with the two techniques, might be attributed to fines and ultrafines enhancement. Data obtained are discussed in terms of physical and physicochemical parameters related to aggregation and capture (of particles by bubbles) phenomena and the practical potential of these techniques are envisaged. The following figure shows size-by-size copper recoveries results, after classification of produced concentrates and tailings using micro-sieves. Results clearly show that flotation of the F and UF fractions is highly improved with injection of small bubbles (SB) and with the addition of an extender collector. It is believed that the techniques presented here will establish shortly a new basis for the flotation enhancement of the F and UF, aimed at solving a very old problem. This work is being continued, now at pilot plant scale, and results will be published en the near future.

Jan 1, 2003

By M. H. Moys, M. M. Bwalya

"INTRODUCTIONThe grinding rate prediction scheme makes use of the energy spectra output from the DEM simulations and the statistical quantification of material strength, which can be done using the drop-weight tester or some other similar equipment. The prediction scheme is evaluated using milling experiments performed under well-defined conditions.MATERIAL STRENGTH QUANTIFICATIONUsing the drop weight test machine, particles of a wide size range were broken singly using different energy inputs. A characteristic equation key to milling rate prediction that relates the probability of fracture with energy input and number of impact attempts was obtained and is stated as follows:"

Jan 1, 2003

By H. Pearce, A. E. Lewis, A. Ochieng

"Hydrodynamics and mixing are fundamental to the operation of mineral process systems such as flotation cells and metal precipitation reactors. Hydrodynamic conditions influence phase mixing and mass transfer in a multiphase system, and these affect the overall performance of such a system. Detailed information on the effects of the hydrodynamics on the performance of agitated systems is still required for the design and optimal operation of hydrometallurgical systems, which are always multiphase. Computational fluid dynamics (CFD) techniques have been employed to study the hydrodynamics and mixing, most of which have focussed on the performance of axial and radial pumping impellers in agitated tanks. However, very little has been reported on the influence of a draft tube on the flow profile in such systems.CFD simulation of a stirred vessel centres on the way the impeller is modelled. Some of the most recent approaches to modelling an impeller are impeller boundary condition (IBC), snap shot, sliding grid (SG), multiple frame of reference (MFR) and inner outer (IO). The accuracy, with which these models predict experimental results and the corresponding computational demands, form the basis upon which the choice of an approach is made. Most of these approaches (IO, SG and MFR) address the key problem of the stirred tank modelling, namely, the simultaneous meshing of the rotating impellers and the stationary baffles. The MFR is computationally cheap and has been found to give predictions that compare well with experimental data.The CFD technique (code CFX4.4) has been employed in the present work to study the hydrodynamics in a mixing vessel stirred with either a Rushton turbine or a pitched blade impeller. The multiple frame of reference (MFR) approach has been used to model both impellers. A draft tube was used only in the Rushton turbine stirred vessel. The flow profiles for the impellers have been studied in three regions; below the impeller tip, at the middle of the tank, and near the liquid surface. The simulation results were compared with literature data obtained using a laser Doppler velocimetry in the three regions of the vessel, and it was found that the model predictions were better in the impeller region. There was a poor prediction of the experimental results in the region closer to the liquid surface; however, this was improved when the turbulence parameter (C2) in the k-e model was set to a higher value. The value of the impeller clearance at which the Rushton turbine generates an axial impeller type flow has been determined and it has been shown that, at this clearance, a draft tube can be used to enhance axial flow in a Rushton turbine stirred reactor."

Jan 1, 2003

By M. Brennan, A. Majumder

"The mineral processing research community has devoted enormous efforts to the modelling of mineral separators over the last 50 years. While many efforts have been made to use only fundamental physics as a basis for the models, fluid flow patterns in separators are not simple while the motion of particle swarms through fluids is extremely complex.Sluices are the simplest forms of the flowing film concentrators and have been used in the mineral industry since at least the 15th century (Agricola, 1556). Flowing film concentrators, in general, still have widespread applications in the mineral industry and their designs vary according to the specific need.Particle separation in a sluice appears deceptively simple, but the separation mechanism has proven complex and difficult to quantify. Separation in the sluice takes place in a flowing film a few millimetres thick. The particles are suspended by turbulent eddies and motion relative to the fluid takes place in socalled hindered settling mode. The difficulty arises because the presence of the particles influences the flow pattern and when the particles are fully transported by the flow, the flowing slurry may not have the same viscosity as water and does not have the same density. For this reason a universal theory which can explain the behaviour of a suspension in a sluice or any other gravity equipment has still not been developed. Few attempts have been made to analyse the mechanisms involved in the concentrating processes of pinched sluices and Reichert cones.Fluid flow behaviour and slurry transportation characteristics in open channels have, however, been active research topics in the disciplines of fluid mechanics, chemical engineering and civil engineering for many years. As a result, an extensive literature is available, which has led to the development of the model described in this paper.In an effort to test the extent to which fundamental fluid mechanics can provide a prediction of particle separation, a study on a simple parallel-sided sluice has been carried out using glass beads at various particle concentrations and flow rates, and the actual particle separation taking place compared to predictions from modelling.The modelling strategy was divided into two parts; the first was to predict the horizontal slurry flow velocity profile and the second to predict the solid particle concentration over the depth of the flow at different flow conditions. The predictions were then validated with measured data sets. This can easily be done if the slurry flow is split at different fractional flow depths so that the mass flow of solids over different flow heights is measured accurately over a fixed period. Mass flow splits can then be calculated by integrating the product of the predicted slurry velocity profile and the predicted solids concentration profiles from the base of the sluice bed to the slurry free surface."

Jan 1, 2003

By Lev O. Filippov, Inna V. Filippova

"Flotation of metal-organic precipitate in column is sensible to the hydrodynamic conditions determined by the diameter and dispersion of rising bubbles. Thus, the dissipation energy in the system resulting of ratio between superficial fluid velocities (gas and feed) in the column is main parameter for precipitate flotation in pilot or industrial scales. The knowledge of aggregate structure can lead to better understanding and control of many solid-liquid separation processes (sedimentation, filtration, thickening and flotation). Many authors highlight the importance of structural properties (i.e. floc density) for different industrial applications.This approach was applied to achieve the flotation of molybdenum precipitate obtained with organic collector a- benzoin oxime for molar ratio 1:2. Flotation tests were carried out at lab and pilot scale with rigorous control of the size distribution of bubbles and the values of dissipation energy in the systems.Structural evolution of Mo precipitate and the destruction phenomenon were described by using of the various fractal dimensions, which were deduced from experimental data of laser sizer devices and optic microscopy pictures of precipitate. The boundary fractal dimensions Df of large aggregates allows the detection of a structural scaled organisation of the precipitate flocs (elementary germs-microflocs-flocs). The fractal dimension of the particle mass distribution Dm=1.94+/-0.15 suggests, for the floc structure, a cluster-cluster aggregation process either with structuration or breakage phases.The destruction process characterised by a fractal dimension Dg controls the final size distribution. The floc destruction occurs for the lowest values of the dissipation energy (0.02 – 0.05 W/kg). The relation between Dg and the system dissipation energy Et (for various energy E dissipated in the agitation cell) involves the different breakage mechanisms of aggregates in function of the aggregation bonds (Fig. 1).Besides, the destruction of floc produces very fine particles (elementary germs or/and microfloc according to E), and thus induces the difficulties of bubble-particle attachment during the precipitate flotation in column. Yet, very small bubbles, which increase the collision probability, would make the flotation feed rate decrease. The optima ratio between superficial gas and feed velocities are determined for bubble size and flotation results control at pilot scale. Thus, it is possible to providing the catastrophically changes of precipitate column flotation by using the following established experimental relation: the mean diameter d of the flocs under the action of dissipated energy Et follows a power like law (d~Et -0.5). This allows estimating the size distribution of flocs for the E values which can appear in column."

Jan 1, 2003

By Wayne van Drunnick, Mervyn Ruthnasamy, Olvier Guyot, Christophe Bouché

"Anglogold’s Mponeng Mine is situated in South Africa’s North West Province approximately 80km from Johannesburg. The reefs being mined in this area are among the deepest deep level mining operations in the world. These shafts often exceed several thousand meters making these operations complex and expensive.The gold plant is fed with run-of-mine ore which is stored in mill silos. Feedrate to the mills is controlled by a variable speed belt. Three parallel SAG mills (4.85 x 9m) treat 80-100tph, operating in closed circuit. Hydrocyclones classify the mill discharge, returning the oversize to the mill feed. Cyclone feed density and pressure are measured and are used with typical control loops to determine water addition rates to the mill. Control loops at PLC/SCADA level were historically used with limited success in the control of the milling circuits. Mill control for an installation of this type used mill mass (measured by load cells) and feedrate to control throughput. An online particle size analyser (PSI) was installed to assist grind control in tandem with pressure/density control on the cyclones. Although the accuracy of the measured grind was reliable, long term consistency of the PSI could not be guaranteed. Economic pressure from the business sector requires consistent mill throughput at optimum grind conditions. Fluctuations in production targets can manifest due to inconsistent control and the lack of real-time information from the process.This sensitivity to process movements may vary between shifts and also with changes in ore competency.Whilst tools are available to improve control, few have the sensitivity to process movements to provide real-time information for optimal grind control. For this reason an Advanced Control solution was sought. Advanced Control is often described as the supervision of basic PLC/SCADA control. Advanced control systems have to seamlessly compliment the existing control strategy and bridge the gap that exists between basic control and optimised control. A solution was found in the Metso Minerals CISA’s OCS (Optimising Control System). This French designed system makes changes to process setpoints to achieve peak performance and is distinguished from others by its soft sensor capabilities. The soft sensor is an embedded module in the OCS package that can be configured to estimate values normally obtained from field instruments. Advanced control using a Fuzzy Expert System assisted by Statistical tools (such as moving averages and a Soft Sensor using Phenomenological Models) would serve to bridge that gap. Metso Minerals CISA’s OCS is a modular system with various capabilities.It was successfully used to provide on-time process information via Soft Sensors. Circuit stability was achieved using Rule Based Expert Control in complete synergy with Fuzzy Logic. Two rule-based strategies were developed for this circuit. The first uses the online product size analyser as a primary control variable. The second uses a calculated kWh/t value and a modelled mill discharge density as primary control variables. The latter had more availability than the particle analyser and is currently in use."

Jan 1, 2003

By Khoi Nguyen, Keeney. Luke

An outcome of geometallurgical mapping and modeling is the generation of continuous down hole profiles of quantitative geometallurgical attributes at assay scale. These attributes vary from traditional routine data collection methods such as assays and geotechnical logging (e.g. RQD, Fracture Frequency), to new measurements including petrophysical attributes, EQUOtip hardness data and modelled estimates of metallurgical performance indices (e.g. A*b, BMWi). Highly variable continuous geometallurgical data with high spatial resolution can make it difficult to identify spatially continuous domains. An automated method based on the well known time series analysis technique of cumulative summation (CuSum) has been developed which uses statistical analysis to identify domain boundaries in down hole profiles. A bootstrap analysis automatically identifies potential domain boundary locations with associated confidence levels and a series of t-tests determine the significance of defined populations. A hierarchical clustering algorithm is applied to results to enable data sensitivity to be taken into account. The method produces statistically significant populations and is suitable for application on either single or multiple drill hole datasets. Domains defined preserve the inherent variability of the continuous down hole data and provide a method for scaling up variability data (i.e. assay interval scale) to mine scale (i.e. bench scale, block model). A major advantage of the method is its ability to provide suitable input parameters for use in spatial modeling of non-additive and non-linear geometallurgical attributes through conditional simulation techniques.

Jan 1, 2014

By D. B. Sundar Ramam

In the recent past, a paradigm shift in terms of resource utilization and beneficiation practices is experienced by the Indian mining and mineral sector. Depleting iron ore reserves coupled with increasing demand for low-alumina iron ore fines to improve blast furnace performance in terms of productivity and reduced slag rate necessitate intensive beneficiation of iron ore. The task is even difficult for Indian iron ores, which are generally high in iron content and at the same time characterized by aluminous gangue. In 2006, M/s Tata Steel commissioned a state-of-the-art Jigging Plant (Batac Jig) at Noamundi Iron Mine (NIM), mainly to reduce alumina in iron ore fines. The jigging plant is incorporated in the existing beneficiation circuit to treat ?10+0.5mm size fraction of classifier fines. Over the course of plant stabilization while the plant could deliver desired ore upgradation and average product alumina, variability in terms of alumina content has been a concern. This paper discusses a case study of process parameters optimization in jigging operation to achieve consistent product quality while improving the effectiveness of gravity concentration for the beneficiation of Noamundi iron ore also to take care of inferior plant feed (input) grade year on year. The operating variables used to optimize jigging operations include bed height, pulsion and suction time, particle size, strokes, and plant throughput rate.

Sep 1, 2012

By Vincent C. Smith, Agit Singh, Bernard Muller

The control of minerals processing plants is by no means trivial. In order to address some of the difficulties, it was decided to develop and test a model predictive controller (MPC) for a milling circuit. A milling simulator was written to test the MPC controller. Due to the large number of tuning parameters in a controller of this type, an optimising algorithm was written that automatically tunes the controller. Good, robust control was obtained when the controller was tuned using this algorithm. The controller was tested for various scenarios that are often encountered in the minerals processing industry. When problems were encountered, the MPC algorithm was specially adapted to accommodate for these difficulties. Control was further improved by using feedforward control as well as quadratic programming. The movement of the manipulated variables was reduced by using a region of uncertainty that allows the controlled variable to vary within a specified region around the setpoint. Integrators were handled by adapting the algorithm slightly and adding an optional integral error portion in the MPC controller. The performance of the enhanced MPC controller was compared to PI controllers on both the simulator and a commercial plant. The MPC controller showed faster responses with less interaction in both cases.

Jan 1, 2003

By Tomasz Niedoba

Coals occurring in nature are characterized by various properties. According to Polish norms, the classification of coals taking into consideration their calorific value contains coals from type 31 (flaming coal) until type 43 (meta-anthracite). The samples of coal of type 31 were taken for investigation. To this purpose, the approximations of ash contents and density distribution functions were done for this coal type (determination of marginal distribution functions). They were the basis for application of so-called Morgenstern distribution functions to approximate the function Z=L (?), where Z is ash contents and ? - coal density. Then, the comparison between obtained results was performed and the results were statistically evaluated. They are the basis for the further research of other types of coals.

Sep 1, 2012

By Takashi Furuyama, Sukeyuki Mori, Tetsuo Ikejiri, Abel Bissombolo, Yoshitsugu Koga, Masamichi Hata

In Japan, the increasing number of automobiles newly put into circulation is followed by a larger amount of end-of-life vehicles from which valuable metals are being recovered in shredder and related plants. Nevertheless, the processing of these scrapped automobiles which has reach a recycling rate of about 75%, generates a huge volume of waste, locally known as .shredder dust., which is commonly dumped on landfills. The saturation and depletion of valuable disposal sites in the near future, as well as the social and environmental problems related to the accumulation of these residues disposals are a major challenge for the automobile shredding industry. To promote an alternative way for the management of these disposals, the authors have initiated and developed a system for their processing, on the basis that more than 90% of these residues are combustible materials that could be used as refuses derived fuel. The developed processing system points out the mechanical/physical separation of shredded automobiles residues into two streams by means of an ascending airflow passing through a vertical zigzag separator and, the compaction of the light-density fraction of materials (that is about 60% of auto shredder residue recovered as float products and mainly composed of cotton, sponges and light plastics) to form a refuse derived fuel (RDF), the density, calorific value and ignition loss of which are 1.19 g/cm3, 4470 kcal/kg and 60.7%, respectively.

Jan 1, 2003

By Roberto Galery, Priscila Esteves, Braz Cardoso, Marcelo Stopa

"It was developed in this work a computational tool to aid in anomaly detection present in the operation of ball mills. The tool uses a torque estimator that is based on measurements taken exclusively in the drive motor. The ball mill equipment widely used in the mining industry has, inherent to its principle of operation, high energy consumption and low efficiency. These characteristics are accentuated when the mill operates outside the ideal conditions of velocity and loading. Direct measurement of these variables is extremely difficult because it requires the installation of sensors in moving parts of the mill. Thus, systems that can help monitoring the operating conditions and predict anomalies are useful because they contribute to improving the performance of the process, help to reduce the energetic consumption, wear on the mill surface and frequency of maintenance shutdowns. The detection strategy implemented in this work is based on the fact that operational anomalies such as an inadequate percentage of balls and incorrect angular velocity manifest itself as a change in spectral components of the torque signal in the mill driven by an electric motor. The mill torque was estimated by processing motor variables measured by sensors commonly used for control purpose and installed exclusively in the motor. The mill was operated at various fault operating conditions and signals from electric motor and vibration on the mill shaft were measured. The spectral components present in the estimated torque signal were then compared with signals from a vibration sensor in order to establishing a correlation with anomalous operation condition of the mill. The experimental results showed that the signals obtained has an excellent correlation with other variables obtained by direct measurement and have potential to be used to construct a system for automatic fault detection in the operation of ball mills."

Jan 1, 2014

By P. S. Mukherjee

Mineral ilmenite is a major resource for titanium, whose major application is for production of Titanium dioxide (TiO2) for pigment application. The production of pigment grade TiO2 from ilmenite was earlier carried out by acid leaching, which has now been banned due to environmental regulations. Further acid leaching leads to loss of iron metal values as sulphate or chloride which are also treated as effluent. In thermal plasma processing the metal values are recovered as high value pig iron and Titanium dioxide is recovered as Titania rich slag containing 80 to 85 percent TiO2. The Titania rich slag has now been considered as a better input material than synthetic rutile for production of pigment grade Titanium dioxide. On the other hand, high value pig iron goes for automobile industry for specific application. An Inflight-flight Thermal Plasma Processing plant, used for the production of Titania Rich slag and high value Pig iron from ilmenite, with 20kg capacity was designed and fabricated. The reactor has the provision to utilize the flue gas generated for preheating the input of raw materials. Various aspects of designing the furnace operation include viz. Feeding the raw material at a fixed rate, designing the crucible used for melting ilmenite, proper cooling arrangements, an innovative method for tapping the melt, recovery of heat from the gases, various safety arrangements which are some of the important milestone of the present work. The various operations have been carried out through a controller panel. Experiments were carried out to optimize various processing parameters using statistical modeling. Large scale experiments have been carried out at 10 to15 kg scale. The material balance has been calculate, and it has been observed, that about 95 percent recovery could be obtained for both Iron and Titanium oxide from ilmenite. The detailed characterization on Titania rich slag and iron has been carried out. It has also been shown that using the above slag, it is possible to prepare nanosized Titanium dioxide powder containing about 98 percent Titanium dioxide by optimizing leaching conditions. Keywords: titania rich slag, ilmenite, thermal plasma

Sep 1, 2012

By M. Ito

Cobalt-rich ferromanganese crust and nodule ores from seamount areas contain volcanic and sedimentary rocks as substrate or nuclei. These ores require mineral processing to remove the sub-strate/nuclei rock before smelting. This paper reviews experimental results of previous investigations. Observations and analysis of 10 samples from different localities were carried out and it was found that the liberation ratio of crushed product was high even at coarse size fraction, 0.5mm to 4mm. Experimental and calculated results in the smelting stage confirmed that the separation product satisfies the standards of the subsequent smelting process if the substrate/nuclei rock is removed from the 0.5mm to 4mm fraction with high separation efficiency. There was a density difference between the substrate/nuclei rock and the ferromanganese component. Thus the coarse sized sample was treated with gravity separation; air table separation was used as a dry method and jig separation as a wet method and high grade values with high recoveries were obtained by both kinds of gravity separation.

Jan 1, 2014

By S. Leroy

Grinding is the most energy consuming step in mineral processing, however, it is still poorly understood and its efficiency is difficult to monitor. Mill performances are traditionally measured at the mill discharge, on the basis of a mass percentage passing a certain sieve. This approach does not reflect what happens to the fines through milling. On another hand, if many macroscopic parameters, such as the percent solids of the pulp, its viscosity, or its mean residence time in the mill are known to be related to grinding efficiency, the link between these parameters and particle size distribution (PSD) is still unclear. Here, a methodology is established to understand the effect of ball mill operating conditions on particle size and shape distribution in the grinding process. The study focuses on the particular case of an Upper Group 2 (UG-2) platinum ore concentrator. Due to the very low grade of sulphide and PGM (Platinum group metals) in UG-2, grinding mechanisms are entirely control by gangue minerals. These two minerals have contrasted properties and PGM content and these properties immediately affect the entire recovery process. So, the grinding of both gangue minerals is studied on a size by size basis. At particle scale, three parameters are addressed: particle size, particle composition and particle shape. The specific behavior of chromite and silicate grains is demonstrated. As a conclusion, this study gives some clues to operate ball mills in a more efficient manner regarding chromite issue in the processing of UG-2. Keywords: ball milling control, UG-2, chromite, fine particle, particle shape, segregation

Sep 1, 2012

By Dilip Kumar Mohanty

In today?s world, Sustainability is the key issue before the mankind. With the ever-increasing population & unimaginable boost in industrial growth to cope up with a steady increase in demand and fast change in life style of a human being, the natural resources are exploited to such an extent that the very existence of living beings in this earth planet is threatened. In such devastating situation, the concept of Sustainability emerges out as a great savior. This concept focuses on minimum/ judicious use of natural resources, thereby preserving the resources for future generation while meeting the bare minimum requirement of the present generation. For an emerging economy like India, Mining and Mineral based industries form the back bone of our economic development. Thus, sustainability of mining and mineral processing industry has a far reaching impact on sustainable economic development of our nation. While at a macro-economic level, we have to strike a balance between economic development vis-à-vis socio-economic & environmental impacts, Industries have to ensure judicious and frugal use of natural resources by making use of energy efficient plants & machineries and adopting befitting technology for reduction & recycling of waste. In the context of the above, it would be interesting to look into the sustainability measures taken up by National Aluminium company (Nalco) at its Crushing & conveying plant at Panchpatmali Bauxite Mine, which is incidentally Asia?s largest Bauxite Mine. In the backdrop of the above stated facts, in this paper the authors make an attempt to bring out the sustainability issues in areas of energy conservation, environmental impact/pollution vis-a-vis mitigation measures adopted in crusher & conveyor plant of Panchpatmali Bauxite Mine & CSR / peripheral developmental activities undertaken by Nalco to mitigate the socio- economic impacts. Keywords: sustainability, energy efficiency, recycle, csr, peripheral development

Sep 1, 2012

By Shuji Owada, Mayumi Ito, Takehiko Nishimura, Toru Yamashita, Sadayuki Shinozaki, Takashi Ando, Tomoe Ota

Electrical disintegration (ED) was applied to Nantun coal (China) in order to improve liberation of coal substance for the pretreatment of producing “Hyper Coal” of which the combustion gas was planning to inject directly to turbine for power generation. It has been found that many cracks generated in the ED were existent at phase boundaries with mineral matters and liberation of coal substance became much higher than that in mechanical comminution methods such as roll crusher. Since the ED occurred more easily (with lower voltage applied) for the coals of higher mineral content, it is considered that this method could make a better contribution especially to comminute middling coals. We also found that the ED technique could apply not only single particles but also to coal particles assemblage, keeping almost the same or higher disintegration efficiency. In the mineral matters, Si and Al components were preferentially well liberated by the ED.

Jan 1, 2003

By P. Chris Pistorius, Johannes Sono, Rossouw Sono, J. J. Kobus

Different coal properties are important in SL/RN (coal-based rotary kiln) direct reduction of iron ore, and in electrical smelting of prereduced iron ore. These differences were highlighted when a plant which processes titaniferous magnetite had to change to different coal types after decades of operation. Laboratory simulation was used to evaluate two candidate coals, which were similar in volatile content and rank, but differed in reactive maceral content. Direct reduction was evaluated by isothermal experiments using a packed bed of ore and coal, measuring the off-gas composition to determine reaction rates and departure from equilibrium. These indicated reduction to be under mixed control, and quite sensitive to temperature (confirming that the coal reactivity is of importance). An aspect of electrical smelting was assessed by determining dissolution rates of the coal in molten iron at 1550°C. Dissolution rates did correlate with differences in coal structure, as determined by X-ray diffraction, with the more ordered ("more crystalline") coal dissolving faster. The conclusion is that the coal which is more reactive during direct reduction is less reactive during dissolution. However, it is concluded that controlling the temperature during direct reduction offers a feasible method to reconcile the two process steps.

Jan 1, 2003

By C. Raghu Kumar

Hydraulic or teetered bed separators (TBS) are finding new avenues for application in the field of mineral processing. Floatex Density Separator (FDS) is a hydraulic/teetered bed separator capable of operating at high tonnage due to its advanced instrumentation. FDS/TBS is being used in Indian mineral sand industry for classification and segregation of different minerals. The purpose of this paper is to provide details on the performance of the plant scale FDS in recovering the chromite from feed (below 1mm size). Historically this feed has been processed using hydrocyclones and spiral classifiers; however, there is a strong trend now to employ teetered bed separators, thus allowing significant changes to be made in the plant for improving process efficiency. In the present work, the performance of the plant scale FDS is described in terms of partition curve (yield, cut size, classification efficiency/Ep) for different combination of process variables and also in terms of metallurgical grade and recovery. It is found that, efficient classification can be achieved at a maximum cut size of 380 µm with and the imperfection is also reported as low as 0.16. The grade of the underflow product is enriched as maximum as 52.2% Cr2O3 from a feed assaying 40.4% Cr2O3.

Sep 1, 2012

By J. Yianatos, C. Matamoros, F. Díaz

The non-selective entrainment of fine solids in flotation equipment has a detrimental effect on the concentrate grade. Reduction of solids entrainment (upgrading) is typically related with a loss in recovery of valuable minerals. For improving the froth transport characteristics and flotation cells design, a better understanding and quantification of the actual solids drainage and entrainment processes are required. In this work, the study of solids transport in the froth of a two-dimensional flotation cell was performed. The prototype cell represents a radial section of an industrial flotation cell (130m3) and was operated at steady state. Experimental tests consisted of adding a small amount of radioactive solid tracer (0.3g) near the top-of-froth or near the bottom of froth (close to the interface). The solid was selected as a non-floatable mineral (gangue) in order to evaluate both the solid entrainment into the concentrate as well as the solid drainage into the collection zone. Solid tracer consisted of fine or coarse gangue particles, P80 of 35 and 120 µm, respectively. Twelve collimated sensors located along the froth and collection zones allowed the evaluation of the solid transport in the froth, and the solid drainage from the froth to the collection zone, after tracer addition at different distances from the discharge lip. Results showed that longer distances to the froth discharge lip, as well as higher particle sizes, promotes higher solid drainage from the froth to the pulp zone, while decreasing the solids entrainment into the concentrate. The same result was observed for the solid located near the top-of-froth as well as near the bottom of froth. This information was complemented by the froth surface velocity measurements, using the Visiofroth system, showing a good agreement between the froth bubbles velocity and the solid transport velocity, measured near the discharge lip.

Jan 1, 2018