Search Documents

By Eric P. Bregman, Franklin M. Grynkewicz, John E. Regan

"As part of an on-going effort to improve water quality and reduce discharge into Boston Harbor, the Massachusetts Water Resources Authority (MWRA) East Boston Branch Sewer Relief Project was designed under a Federal mandate from the United States Environmental Protection Agency (EPA) to upgrade the aging sewer system, increase system storage and greatly reduce the volume of combined sewer overflows into the Harbor. The project scope of work includes the installation of over 2 miles (11,800 linear feet) of 36-inch and 66-inch diameter sewer relief piping, twenty (20) temporary shafts and an approximate 100 foot open cut section, located within the densely populated neighborhood of East Boston, Massachusetts. This area is a former marshland backfilled in the early to mid 1800’s where busy commercial streets co-mingle with thickly settled residential houses.The subsurface conditions present within Boston’s complex geology include the presence of subsurface contamination as well as complex networks of underground utilities. Additional site limitations included low headroom, noise, and traffic restrictions. Together these limitations required the design of individual earth support systems, tailored for each shaft location. Moreover, challenging subsurface conditions identified during construction required design modifications to minimize cost and schedule impacts related to construction dewatering, treatment of contaminated groundwater, internal bracing, and utility relocations.This paper provides a case history of the Geo-structural design and performance of various earth support techniques utilized to construct jacking and receiving shafts designed to launch and receive two (2) micro-tunnel boring machines (MTBM) and to support the construction of new deep shaft structures in an urban coastal area."

Jan 1, 2017

By Babu K. V., Samyukta P.

The energy demand in India is expected to show increasing growth in the next few decades. The oil companies in India are revamping the existing oil refineries as well as constructing new refineries across the country to meet the energy demands. Most of the refineries in India are located along the coastal region because of the ease of transporting crude materials. Considering the criticality of the structures as well as soil conditions in the coastal region, pile foundations are used in refinery plants. In India, non-displacement piles in the form of bored cast-in-situ piles are used to support structures. In a few circumstances, displacement piles in the form of driven cast-in-situ piles are also being used to support critical structures. This study presents the performance of non-displacement and displacement piles for similar ground conditions at the same project location. The pile load test results have shown that the settlement observed for displacement piles is lower than compared to non- displacement piles for a given loading and soil conditions. This shows that the performance of displacement piles is slightly better in comparison with that of non-displacement piles.

Sep 1, 2022

By M. D. Riegel, Brian T. Felber

"Construction of foundation elements in an urban environment is often complicated by multiple constraints such as existing foundations, utility conflicts, maintenance and protection of traffic on high volume roadways, low overhead clearances, and vibration and displacement monitoring to reduce risks of impact to existing facilities. Micropiles are commonly a preferred foundation alternative in an urban setting to mitigate some of these risks. This paper presents examples in which micropiles helped reduce risk in an urban setting on the two subject infrastructure improvement projects. The case studies presented include the Verrazano Narrows Bridge HOV and Bus Ramp Improvements in Brooklyn, NY and the Kosciuszko Bridge Replacement in Queens and Brooklyn, NY. The paper details the micropile design, how risks were mitigated, and the complications to each of these projects associated with the urban setting.INTRODUCTIONThe paper begins with background information about the Verrazano Narrows Bridge HOV and Bus Ramp Improvements Project, followed by background information for the Kosciuszko Bridge Replacement Project. This introductory background information is followed by discussion of the urban site constraints, which controlled the foundation type selection for both projects. In closing, the paper discusses the micropile design process, load testing, and construction.VERRAZANO NARROWS BRIDGE HOV & BUS RAMP IMPROVEMENTS BACKGROUNDProject ScopeThe project consists of two new ramps; one designated for HOV / Bus traffic between Staten Island and the Gowanus Expressway, and one to be utilized for storing the barrier transfer vehicle. Also included is the complete reconstruction of Ramps B and F to accommodate horizontal and vertical alignment clearances from the new ramps, removal of the median of the upper level to add one lane, utilities improvements, stormwater improvements, and miscellaneous structural repairs. The new HOV / Bus Ramp was designed for reversible traffic flow to accommodate the demand of the peak traffic direction by movable barrier.Geotechnical / Foundation Engineering ScopeThe geotechnical work included a desk study review of existing plans, geotechnical reports, and geologic maps. This data was subsequently supplemented with a subsurface exploration program. Once completed, foundation design was performed for 25 proposed bridge substructures. Four existing battered pilesupported foundations and two shallow foundations were evaluated for increased loading. Upon completion of the foundation design, foundation plans, specifications, and an engineer’s estimate were prepared. Foundation installation was observed on a part-time as needed basis."

Jan 1, 2016

By Guo Qian, Du Guangyin, Deng Yongfeng, Liu Songyu, Wang Ningping

"Metakaolin (MK) can efficiently enhance the strength and the impermeability of concretes and mortars. However, it has rarely been attempted in admixtures of cement-stabilized soils until presently. As deep mixing method is wildly used in ground improvement, the strength of cemented soils (soilcrete) and the applicability of the MK should be considered. This paper focuses on the macro-strength development of cement-stabilised silty soil mixed with MK. The result shows that the addition of MK can enhance the unconfined compressive strength of the soilcrete, which attributes to a combination of the rates of OPC hydration and the MK-CH reaction. Note that the strength of soilcrete was influenced by the properties of soil, water-to-binder mass ratio (W/B) in admixtures, which needs to be reconsidered since the binder mass composes that of cement and MK totally.INTRODUCTIONCement was used in ground modification techniques, such as the jet grouting, deep mixing method (DMM) which was put into practices in Japan and Nordic countries in the middle of the 1970s, and then spread to China, South East Asia[1]. For last decades, fly ash, slag or silica fume was mixed with cement to form the new cement base stabilizing agent in the view of economy and performance improvement. The mechanical behavior of these soil-binder admixtures (nominated as “soilcrete”), was investigated. But the soilcrete modified with the metakaolin (MK) was still not investigated much and lots of further work needs to be conducted.Some laboratory experiments of the soilcretes modified with MK have been taken[2~4]. Kolovos et al. (2013) indicates that the unconfined compressive strength has a more significant improvement when W/B equals 0.4 than that when W/B equals 1.20 concerning the water-to-binder mass ratio (W/B). Sonebi et al. (2013) investigates the mechanical behaviors of cement grouting containing MK with W/B equals 0.4, and also found the effectiveness of the addition of MK. Zhang et al. (2014) performed the studies on Lianyungang marine clay improvement showed that MK obviously enhanced the quality of cemented soils.In this paper, the strength of soilcrete modified with MK is further investigated, where the unconfined compressive strength at different curing time, the content of MK and cement (w/w) in lab conditions was discussed."

Jan 1, 2015

By Tian Miaomiao, Cheng Yin, Shen Jun, Yu Hao, Li Yafei

Vast amounts of waste drilling mud containing heavy metals is produced during oil drilling process, which causes great pollution to the environment. Therefore, it needs to be treated until it is harmless. This study uses industrial waste and Portland Cement stabilized waste drilling mud; the unconfined compression strength, leaching amount of Pb2+ and Cr6+ ions, and pore size of the stabilized soil were tested at different times during freezing-thawing cycles. The antifreeze performance of the stabilized drilling mud with industrial waste is discussed. The results show that the strength of the stabilized soil decreases with an increase in the number of freeze–thaw cycles. The strength loss of the stabilized soil after freeze–thaw cycles can be effectively reduced by increasing the industrial waste content, especially the content of phosphogypsum in the stabilizer component. Pb2+ ions and Cr6+ ions can be effectively stabilized by industrial waste. The results of the pores test prove that the compactness of stabilized soil solidified by industrial waste residue is greater than that of cement alone.

Nov 1, 2022

By I. D. McPherson, Dominic P. Mahoney

The Metro Sports Facility is currently under development in Christchurch, New Zealand and is a key Anchor Project in the city’s post-earth quake recovery. When completed it will be largest indoor sports and swimming pool complex in New Zealand, with a building footprint in the order of 22,000m2. The site is underlain by poor performing soils comprising interbedded layers of soft compressible silts and loose liquefiable sands to over 20m depth. The site is typical for Christchurch with a shallow groundwater table and artesian conditions. The site performed poorly during the 2010-2011 Canterbury Earthquake Sequence with extensive liquefaction, and associated ground damage. To provide a resilient and economical foundation system for this key development project, deep ground improvement comprising of a uniform grid of some 7,200 stone columns in conjunction with robust shallow foundations has been adopted. This paper discusses the geotechnical site constraints, and ground performance under earthquake loading and describes the various options considered for the development. The foundation option selected, the design considerations of the adopted stone column ground improvement, and foundation solution are described in detail, as well as, construction observations. The paper aims to provide insight into an urban large-scale ground improvement project for the engineering practitioner.

Nov 1, 2022

By Abhirami B., V. Balakumar

Piled raft foundation system is an intelligent geotechnical concept, developed towards reducing the settlement of the raft and the footings by providing pile elements below the raft or footings, as the case maybe. Although a large volume of works has been done on the behaviour of piled rafts by observational studies, the effect of construction methodologies such as deep excavations, the installation methodologies used for piling etc appear to have not been covered adequately. This paper discusses the effect of deep excavations, pile installation techniques and the effect of adding structural elements, based on the data available from published literatures. Based on this study, the performance of the piled raft monitored by the author has been revisited and the results of such a study are discussed.

Nov 1, 2022

By Bruno Vingiani, Alessandro Bertero

"The use of Artificial Ground Freezing (AGF) for temporary soil strengthening and seepage control is an effective alternative to grouting when dealing with soils whose degree of finesses would imply the use of highly expensive chemical grouts. However, compared to grouting, the application of this improvement technique usually needs a more accurate preliminary soil investigation campaign and a design assisted by specific calculation software. Besides a general description of the main features of this technique, the paper will describe a recent application of AGF carried out in Rome to underpass an existing metro station.INTRODUCTIONNatural ground freezing occurs seasonally or permanently (permafrost) in some areas of the globe close to the poles and can negatively affect the engineering performance of underground structures. On the other hand, Artificial Ground Freezing (AGF) is man-made controllable freezing process that can be used in foundation engineering to temporarily strengthen the ground and create a barrier to the passage of groundwater. During the process, the heat is extracted from the soil in a cylindrical shape around a number of freezing pipes installed into the ground. This action produces columns of frozen soil, which expand gradually till they merge and create continuous frozen wall. The thickness of this barrier can be regulated according to the specific project requirements. Nowadays, AGF technique is applied to a wide range of foundation engineering problems where soil stability and groundwater flows are an issue (Pimentel et al. 2011, Haß and Schäfers, 2013). Typical applications include the temporary stabilization and waterproof of the ground around the excavation profile of mined tunnels until the construction of the final lining (Figure 1).The case history described in this paper deals with a recent application of AGF carried out during the construction of metro Line “C” in Rome. Specifically, this technique has been applied to allow the construction of two single-track mined tunnels running underneath an existing metro station belonging to Line “A”. In that case, the AGF has been evaluated by the Designers as the only possible solution for improving the mechanical and hydraulic characteristics"

Jan 1, 1900

Jan 1, 2001

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Sep 8, 2021

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Oct 1, 2021

By Chu E. Ho, Paul Napoli

A new waterfront park was developed on Long Island in close proximity to the East River and Newtown Creek. The existing ground consisted of fill over soft organic clay, medium dense silty sand, glacial till and schist bedrock. The ground was initially raised to preload the underlying soft soils to stabilize the ground in preparation for site development. The ground was subsequently cut down to temporary grades for installation of foundation piles for the overlook structures and construction of reinforced concrete cantilever retaining walls forming pathways located adjacent to the water bodies. The retaining walls were located in two rows at different elevations along the sides of a steep embankment. Where the pathways converge, some of the walls were too close to each other, and were redesigned as a combined U-wall with a common base slab. The individual retaining walls were designed for adequate bearing, sliding and overturning resistance. Ground anchors were installed to enhance global stability of the retaining walls. This paper presents the design considerations for the retaining walls for various loading conditions, and evaluation of the trial and proof tests for the anchors. INTRODUCTION The New York City Master Plan included the transformation of an approximately 30-acre parcel of land in Long Island City, Queens, New York from a former manufacturing zone into a residential, commercial and recreational zone for middle-income community. The site was located at Hunters Point South along the eastern shoreline of the East River and Newtown Creek (Figure 1). The development included low to high- rise residential buildings, a public school, and retail structures. Open spaces were provided along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community-related activities. Waterfront structures included small park buildings, walkways and viewing platforms. The shoreline was surrounded by revetments as part of the flood mitigation strategy. The project involved extensive site re-grading and several retaining walls were constructed. The earthwork volume amounted to approximately 47,000 cubic yard of imported fill and 93,000 cubic yard of cut. The exposed height of the retaining walls ranged from 3 to 15 feet. This paper focuses on the design and construction of the retaining walls for the project.

Jan 1, 2019

By J. S. Lee, R. K. Massarsch

"A 3.2 km long immersed road tunnel forms part of the Busan-Geoje Fixed Link in South Korea, which connects Korea's second largest city Busan, with the island of Geoje. To ensure the water tightness of the joints of the segmental tunnel structure and to limit the forces in the shear keys, the differential settlements have to be limited. This was achieved by extensive soil improvement of the marine clay below the tunnel with cement deep mixing (CDM) and sand compaction piles (SCP). This paper focuses on the characteristics of the marine clay, the basic design principles, layout and constructional issues of the CDM soil improvement, and numerical and numerical analyses to predict settlement and stability.INTRODUCTIONThe Busan-Geoje Fixed Link consists of two short cut & cover tunnel access ramps, a 3.2 km long immersed tunnel (Figure 1) and two long span cable stayed bridges. The tunnel consists of eighteen concrete elements each of 180 m length having a rectangular cross section of 26.5 m in width and 10 m in height. The tunnel elements are cast in a dry dock on shore and floated out to the sea, immersed in their final positions on a gravel bed in pre-excavated trench and connected to each other by a dual gasket system. The water depth was up to 50 m making the tunnel of the deepest yet constructed. After immersion, the tunnel is protected by backfill material at the sides and rock armour on top. Each tunnel element consists of eight 22.5 m long segments. The joints between the segments and between the tunnel elements are equipped with EDPM water stops, Omega seals and concrete shear keys. The longitudinal displacement behaviour of the segmental tunnel structure in the varying ground conditions represents a complex soil-structure interaction problem which has been modelled with a FEM structural model representing the tunnel, the joints and with springs to represent the soil that are derived from the PLAXIS soil/foundation models. In order to ensure the water tightness of the joints which have limited opening capacity and to limit the forces in the shear keys, differential longitudinal settlements have to be limited. This is achieved by limiting the variations in subgrade modulus along the alignment and it in practice means that differential settlements are limited to a few tens of millimetres. Without soil improvement of the marine clay below the tunnel, long-term tunnel settlements of up to 400 mm were predicted when taking into account the likely variations in the trench profile, backfilling and uncertainties in the soil properties. Such large total settlements led to large variations in the sub-grade reaction along the alignment, which in turn resulted in significant differential settlements, unacceptable joint opening and large shear key loading. It was therefore decided to carry out extensive soil improvement with cement deep mixing (CDM) (CDIT, 1999) and sand compaction piles (SCP) (Kitazume, 2005) after studying a number of foundation alternatives."

Jan 1, 2015

By Dimitrios Polantzas P. E., Collin E. Sweeney E. I. T., Franklin M. Grynkiewicz P. E., Leili Javidanian P. E.

In the latest AASHTO design specifications, the Load and Resistance Factor Design (LRFD) method is prescribed for the design of retaining walls. However, inconsistencies arise when LRFD is used for retaining wall design versus the traditional Allowable Stress Design (ASD). Required toe embedment and wall loading demand vary greatly when the two design approaches are compared, all else being equal. This is due to application of linear load factors to properties that vary non-linearly in the design. These inherent inconsistencies are further intensified when introducing factors such as layered soil profiles, different wall types, groundwater elevation, and surcharge requirements. When applied correctly, these two design approaches, in theory, should lead the designer to the same result with little discrepancy, as they do with steel structure design. However, the use of the current AASHTO LRFD method for various geostructural retaining wall designs yields contradictory results that suggest existing retaining walls that have been successfully designed and constructed are unstable. Fundamentally, LRFD should be built on reliability-based calibrations; the successful past performance of existing retaining structures designed using ASD suggests that the LRFD approach requires considerable modification. The authors of this paper recommend that the current LRFD load factors be reviewed and revised based on more comprehensive wall performance data and wall type such that the difference between retaining structures designed using LRFD and those designed using ASD is eliminated.

Oct 1, 2022

By Paul Thurlow, Richard K. Lipscombe

The measurement of deflection of designed diaphragm walls is critical for near real time information to assess wall and soil behaviour as the internal area is excavated in a controlled manner. Data enables the site team and designers to check performance of the design, which is linked to safeguarding the site and the external stakeholders.This paper documents the use of Shape Accel Arrays at the Tottenham Court Road Western Ticket Hall during excavation and propping within the diaphragm wall for the Crossrail project. It shows how the data obtained was used within the site settlement management plan to assist in the control of the works and the information used for Value Engineering purposes that benefitted the project.The use of Shape Accel Arrays for measuring the deflection of retaining walls is not commonplace in the UK construction industry, with the Tottenham Court Road Western Ticket Hall being one of the first times they have been used in such a way. A detailed analysis of the data obtained from the instruments has been undertaken, and compared to the results obtained from the manual inclinometers that were read next to the SAAs. The advantages of the relatively new SAAs have been discussed, as well as other applications of the instrument.

Jan 1, 2017

By Federico Pagliacci, Claudio Asioli, Marco Chiarabelli

"""Rigid inclusions"" are a consolidation method that provides improvement of soft soils thanks to the installation of cylindrical columns made up of a material with significant and permanent cohesive properties, whose stiffness is 500÷5000 times greater than the surrounding natural soil’s. ""Rigid inclusions"" find their application in marginal areas (reclamations, polluted sites) to ensure stability of adjacent structures during construction of new buildings and to reduce the impact of natural disasters (liquefaction in the event of earthquakes, embankment collapse in the event of floods). This paper analyses the “rigid inclusion” construction method, related materials and equipment. Moreover, two performed projects will be illustrated. The first is the restoration of Lungarno Torrigiani Embankment in Florence, Italy. In May 2016, the Torrigiani embankment underwent a structural collapse causing a 3 m. displacement of the riverbank towards the Arno River. “Rigid inclusions” (with 300 mm diameter) have been used to re-compact the loose soil and create a stable working platform for the equipment. The second project illustrates the use of “rigid inclusions” (800 mm diameter and maximum depth of 36.6 m) to control the settlement of a new automatic cold store (30 m high with a 65 x 120 m foot print) for fresh frozen vegetables.RIGID INCLUSIONSIn general, the word ""inclusions"" means a type of consolidation that improves the strength of a soil mass through the inclusion of elements constituted by a material having better characteristics than those of the surrounding natural ground, to improve the overall mechanical characteristics of the treated soil. Inclusions are ""rigid"" when the material introduced into the ground has significant and permanent cohesive properties (concrete or cement mortar) and a significantly higher stiffness (500 ÷ 5000 times) than that of the surrounding natural ground.Typically, medium-small diameters (from 300 to 800mm) with low percentages of treatment (from 2% to 10% of the volume of soil) are employed, ensuring a high quality and consistency of the obtained product, both in terms of diameters and elastic modulus.According to the scope of the project and in urban areas, ""rigid inclusion"" columns can also be performed by means of small diameter drilling rigs (micropiles), weighing less than 20-25 tonnes."

Jan 1, 2017

By Madhu. P, Srinivas. K

Measurement of thermal properties like thermal conductivity, thermal resistivity, heat capacity and thermal diffusivity for materials, it plays a crucial role in a wide range of various civil and electrical engineering projects, and many field applications like building’s basement, power generation, underneath soil heating, wastes from nuclear as well as thermal plants, and buried cables. Thermal conductivity of soil depends upon various geotechnical parameters such as type of soil, moisture content, particle size distribution, density, and compaction characteristics. Earlier studies, the measurement of thermal conductivity of soil by incorporating the heat source methods. Thereby expensive and time taken to conduct in laboratory as well as field measurements. The thermal conductivity is determined by fabricated probe and used in this work. Fabricated probe was calibrated with glycerin. The thermal conductivity of the soil increases as the water content and density increase because these factors are majorly influencing and water has a higher thermal conductivity than soil minerals, and grain to grain contact increases as density increases. therefore, Thermal conductivity is higher in coarser soils than in finer soils. The details regarding of this work as explained in this paper.

Sep 1, 2022

By Susan Rafalko, Mike Walker, John Sankey, Sherif Aziz, Alex Potter-Weight, Mary Nodine, Frederic Masse

"After several successful projects on the Garden State Parkway and New Jersey Turnpike for support of single-stage MSE (Mechanically Stabilized Earth) walls using rigid inclusions (Controlled Modulus Columns) as an alternate to two-stage MSE walls and surcharge, the Bass River Bridge Widening project presented additional challenges in terms of soil conditions and height of embankment that created opportunities for the design-build ground improvement contractor and its MSE wall-designing partner to enhance their design and construction methods. The specialist contractor decided, in association with the wall system supplier, to perform an independent large scale instrumented test area on the project to demonstrate the ability of the design techniques to model the behavior of the system, as well as the capacity of the rigid inclusions to provide the necessary bearing capacity and settlement control to allow the construction of the highway without any consolidation period. This paper presents a detailed description of the design of the ground improvement system and MSE wall system, as well as the results and conclusions of the monitoring data gathered on the large scale test program. The combination of rigid inclusion ground improvement technologies, such as the CMC system, together with an MSE wall system allows for the rapid and economical construction of high embankment without waiting for a surcharge and consolidation period or the necessity to use a two-stage wall system. In-depth understanding of the design techniques and advantages of this combination will be provided and should be beneficial for any geotechnical engineer or owner looking for innovative solutions to save both time and cost on their projects.1. IntroductionAs development continues on sites with poor ground conditions throughout the world, conventional MSE walls remain a flexible design solution; however, construction of MSE walls in combination with ground improvement is becoming more frequent where extreme differential and/or total settlement prevail due to soft ground conditions. Various techniques have been used in the past in such conditions (e.g. conventional surcharge, staged construction, or two-stage MSE walls), even though these design solutions have typically involved longer waiting times for settlement to occur. As a result, conventional MSE wall design has been combined with a variety of ground improvement techniques consisting of rigid inclusions for an economical and efficient solution with the potential to accelerate construction and limit long term settlement. For the particular subject of this paper, the specialist contractor (Menard) proposed to use CMCs (Controlled Modulus Columns) to support the highest part of the MSE wall. CMCs are grouted displacement rigid inclusions installed in a grid-like pattern using a displacement auger. Before the CMCs are installed, a working platform may first need to be placed to allow equipment to move around the site depending on the ground conditions. Following the CMC ground improvement, an LTP (Load Transfer Platform) is installed prior to the construction of the MSE wall."

Jan 1, 2015

By Yazen Khasawneh, Yao Zhang

Upgrading and maintenance programs were proposed at a power generating plant in Indiana. To perform construction activities associated with the proposed upgrading and maintenance, a LR11350 crawler crane with a dead load of 1,500 ton was required in the vicinity of existing plant structures. The contact pressure from the crane tracks for the heaviest lift, maximum reach and angle (worst loading condition) were estimated by the rigging engineer to be on the order of 84 psi. Several concerns were raised regarding the total and differential settlements while the crane is in operation and the induced stresses on existing underground utilities due to crane loads. Three-dimensional finite element simulations were conducted using hardening soil model for the subsurface soils and elastic model for the other structural elements (underground utilities and crane mats) to optimize the configuration of the proposed crane foundation. It was found 1-foot thick engineered steel mats underlain by a 1.5-foot thick crushed stone pad will provide enough support to the crane. It will also control the settlement to the allowable limit and maintain the stresses in the underground utilities within tolerance. INTRODUCTION A LR11350 heavy lift crawler crane was proposed as part of an upgrade program at an existing power plant in the state of Indiana. The proposed crane will be sitting on an open ground in the vicinity of existing plant facilities, with multiple underground utilities going beneath the proposed footprint of the new crane pad. The existing utilities are of diverse kinds, including sanitary sewer corrugated metal pipes, electrical conduits and variable steel water/oil drain pipes. The safety and functionality of these underground utilities are critical to maintain the proper operation of the power plant. Therefore, the design of the new crane pad foundation system is of essential to control the ground settlement and the imposed stresses to the existing utilities (Davie et al., 1998, Scott 2017). To ensure all utility locations and depths are identified, the proposed footprint was thoroughly surveyed. Information in regard to each identified utility was provided by the owner. Subsurface explorations were conducted using geotechnical soil borings and soundings to evaluate the ground conditions and generate soil profiles. Numerical simulation and analysis utilizing finite element method were performed to design the crane pad foundation system and evaluate the responses of the utilities. This paper summarizes project information, geotechnical conditions and then focuses on the finite element analysis in assisting the design of crane pad and the utilities evaluation.

Jan 1, 2019

By Mohamed Mekkawy, William W. Wheaton, Ira Brotman

"The Virginia Port Authority and the U.S. Army Corps of Engineers are partnering to construct the Craney Island Eastward Expansion (CIEE) to meet the dual purpose of extending the life of Craney Island as a dredged material management area and providing land for a state-of-the-art marine terminal. The over 500-acre (200-hectare) expansion provides additional upland dredged material capacity for the Hampton Roads Harbor by constructing perimeter dikes, that once filled, will provide land for the development of a container terminal. In the winter of 2010/2011 the first stage of sand fill was placed, followed by the installation of approximately 12 million linear feet (MLF) (3.6 million linear meters, MLM) of marine PVDs. With over 36 MLF (10.9 MLM) of PVD required to complete dike construction the project will be one of the largest PVD installation project in the U.S.This paper details the challenges associated with the construction of the cross dikes, in particular the design, testing, installation and monitoring of prefabricated vertical drains (PVDs) installed overwater to depths of over 130 feet (40 meters) for foundation improvement in the insitu very soft Norfolk Clay. With expected settlements of 20–30 ft (7-10 m) and 30 percent average strains, the discharge capacity of the PVDs was of particular concern. Laboratory data is presented showing the magnitudes and variability of discharge capacity under different confining pressures in both a straight and buckled condition.The method of installation and monitoring of the marine PVDs in open water included developing a specialized barge and sophisticated positioning and data collection system to verify installation location, depth of penetration and track quantities. An observational method, including material testing, detailed surveys, periodic in-situ testing, and instrumentation, was utilized by the project team to assess the project’s progress and allow for validation of consolidation and strength gain rates and magnitudes."

Jan 1, 2017