Search Documents

By Arash Khosravifar, Matt Steffan

An expansion of the City of Klamath Falls Wastewater Treatment plant required geotechnical seismic hazard evaluations and deep foundation design. The site is located on the shore of Lake Ewauna and is underlain by diatom rich lake deposits. Diatomaceous soils exhibit unique engineering properties that are not well understood. Cyclic Direct Simple Shear (CDSS) testing was performed on three undisturbed samples to evaluate cyclic and post-cyclic properties of the diatomaceous soils. Results from the CDSS testing indicated that the soils would not liquefy in the classical sense, though cyclic softening behavior was observed. The CDSS results were used to develop a Cyclic Resistance Ratio curve for the diatomaceous soil to compare with clean sand liquefaction curves. Seismic lateral pile capacities were developed using two approaches. One approach used conventional p-multipliers for liquefied soil and modified them to reflect expected excess pore pressure ratios. The other approach applied residual strength and fifty percent strain values from post-cyclic monotonic shear testing. A lateral spread hazard zone was identified along the Lake shoreline and reduced, seismic lateral pile capacities were recommended. The objective of this paper is to report the seismic design considerations for this project in a unique geologic and seismic setting. INTRODUCTION The engineering properties of diatomaceous soils have rarely been studied and the cyclic behavior under seismic loading is generally unknown. Some of the critical geotechnical uncertainties of diatomaceous behavior include potential for large consolidation settlement, influence of irrecoverable strains due to diatom particle crushing, shear strength (peak and residual), and cyclic properties. This paper presents results of cyclic shear testing, seismic evaluations and seismic lateral pile design in diatomaceous soils performed for the expansion of a waste water treatment plant in the city of Klamath Falls, Oregon, site of the largest recorded earthquake in Oregon’s history. The expansion consisted of adding six new facilities at the existing Plant including influent pump station (IPS) and headworks, aeration basin, tertiary treatment, and other buildings. The IPS/headworks and aeration basin will be founded approximately 15 feet below ground. The other buildings will be founded at grade. The existing facilities are supported by timber piles that penetrate the surficial diatomaceous soils and terminate on a hard underlying deposit. Figure 1 shows the site plan and proposed additions.

Jan 1, 2018

By Darrell Wilder

When designing excavation support systems in urban environments, it is often necessary to consider the effect of vertical surcharge loads from adjacent structures. Several methods are used in practice to establish the horizontal surcharge-induce pressure on the excavation support. According to the experience of the authors, these methods often seem to overestimate the effect of the surcharge and may have significant impact on the construction costs. This paper explores several of these procedures and provides a discussion as to the reasons for the differences in surcharge effect predictions between different procedures. It also provides practical recommendations for designers dealing with excavation support design.

Jan 1, 2006

By Mathew Janes

"Sheet piles remain an economic solution to many shoring problems. However, installation of sheet piling suffers high noise and vibration with conventional impact or vibratory methods or low production and high expense with push techniques. Many projects simply will not allow sheet piling due to vibration concerns.Installing sheet piles with a tunable, high frequency Resonant vibrator provides high production with imperceptible ground vibrations. Recent projects in Canada have proven the technique on production projects where vibration sensitive structures are present immediately adjacent to the sheet piling. A project in Whitehorse, Yukon required a Waterloo style impervious sheet pile barrier be driven immediately adjacent to a sensitive, large diameter sewer line. The 1800 m2 Waterloo barrier was driven to prevent hydrocarbon leachate from entering the Yukon River. Proposed driving of the sheet raised concerned as the sewer serviced downtown Whitehorse. Monitoring of the sewer during Resonant driving proved the ground vibrations to be imperceptible. Use of the Resonant Driver prevented all concern over ground borne vibration of the sewer and allowed the contractor to progress at conventional, high production while maintaining low cost to the owner.Subsequent projects continue to prove that Resonant driving of sheet piles achieves high production while eliminating ground vibration.IntroductionA complex environmental clean-up problem required a unique solution. A historic oil and fuel transfer station in Whitehorse, Yukon is located on the Yukon River. The facility has been in use since the Second World War and witnessed much careless activity. The sand and gravel site provided ease of transmission of hydrocarbon leachates directly into the Yukon River. Continued use of the site required a barrier wall be constructed to prevent hydrocarbon from leaching into the Yukon River. A short construction season and restrictive fisheries window made for a compressed schedule. Along the shoreline of the property and within the required clean up zone a large diameter sanitary sewer collector line was present that serviced the majority of downtown Whitehorse. The design called for a barrier wall to be constructed along the waterfront adjacent to the sewer with cofferdams constructed out into the Yukon River to recover contaminated riverbed soils. The coarse sands and gravels meant high hydraulic conductivity into any kind of excavation, including slurried or drilled shafts that may have been used to construct a low vibration shoring system. Conventional hammer or vibrator technology would result in high ground vibrations that risked damaging the sewer. The Resonant Driver method was selected for its ability to drive sheet piles with high production and zero ground borne vibrations."

Jan 1, 2014

By Shuvranshu K. Rout, Anup K. Mandal, Biswajit Das, Manos De

"To adopt new technology advancement in Steel Plant, there is a requirement of shifting of operation process from Coke Wet Quenching (CWQ) to Coke Dry Quenching (CDQ). New CDQ chamber foundation with deep basement and underground conveyor tunnel are to be constructed in an operating plant where heavy foundations and structures are located in close proximity. Furthermore, the existing CWQ system will be in operation during new underground construction and erection. Challenges to deep excavation of tunnel and chamber foundation consist of non-uniform ground condition, prevent washing out of soil from bottom of existing foundations, stability of existing nearby structures, presence of large number of underground utilities, ensuring safe underground workplace to construction resources engaged in new construction work along with project schedule and budget constraints. A combination methods involving use of soil nailing, soil grouting, contiguous bored pile and micro pile had been adopted for protection of excavation sides as well as existing structures. Each side of excavation in different stretches were analysed during design as well as construction stages. The use of combination of all techniques in a single brown field project in context of the nature of site constraints and safety issues made this a unique project.INTRODUCTIONSteel Industry is one of the backbones of industrial growth of any developing country like India. Due to increasing land prices most of the steel plants in India are expanding within their existing plant facilities. In addition to that, there is demand of adoption of new technology for future expansion projects to set new benchmarks with global standards.The property owner had earlier installed a Coke Wet Quenching (CWQ) for their Coke Plant. Now, there is a requirement from process department to proceed with Coke Dry Quenching (CDQ). To facilitate the CDQ within the existing CWQ which will be in operation is the main challenge for the property owner. The second challenge is the limited space for underground construction and subsequent equipment erection within the stipulated time frame.From a geotechnical prospective, the project team had uncertainty and reservations in their mind about the construction methodology. Therefore, the role of three “C”: ‘Consultant’-‘Client’- ‘Contractor’ and their combining brainstorming is essential to freeze a working plan for achieving the goal. In this paper, only the excavation support systems for underground foundation structures have been highlighted in the context of solving geotechnical problems."

Jan 1, 2017

By R. Bruce Patterson

The New Tacoma Narrows Bridge is a classic suspension bridge founded on concrete caissons. Caisson construction was complicated by the proximity of the existing bridge piers, only sixty feet away. High capacity plate anchors were used successfully to moor the new caissons in currents as strong as seven knots during construction.

Jan 1, 2004

By Ken Andromalos

Continued population growth combined with limited water resources in the Denver area has resulted in the conversion of a number of mined out gravel pits in the area into municipal water storage facilities. The use of slurry walls provides a cost effective means of isolating groundwater to convert these pits into efficient water storage facilities. Design considerations include: stability, underlying bedrock conditions, backfill mix design and earthwork requirements. Installation issues during construction include: trench stability considerations when excavating through relatively clean sand and gravel deposits in potentially high groundwater conditions; keying into three to ten feet of fractured claystone, siltstone or sandstone that makes up part of the Denver formation, and quality assurance procedures to assure a proper groundwater barrier is constructed. The paper concludes with two brief case histories to illustrate how these considerations are applied

Jan 1, 2007

By A. Mazzucato

This paper presents the experimental results of driving and load tests on an instrumented pile driven into a test pit filled with fine homogeneous sand.

Jan 1, 2010

By Robert Bittner

The following is a report on the development of two unique and separate cofferdam systems used in the construction of the marine foundations for the I-205 Columbia River Bridge at Portland, Oregon for the Oregon Department of Transportation. The first of these two systems utilized interlocking H-pile 100 ft long to form a cofferdam 145 ft by 58 ft in plan and 100 ft deep. The second system consisted of two immense bell shaped steel forms. The larger of the two forms was 83 ft by 66 ft in plan, 62 ft high and weighed 450 tons. This form was externally stiffened for a designed hydrostatic head of 54 ft. Both forms were designed, except for the top 14 ft, to be set and stripped in one solidly welded unit. The supporting geological formation for the bridge foundations is the Troutdale, a cemented sand and gravel. This formation is at the ground surface on the Washington Shore and slopes downward to a depth of 115 ft below normal high water at about mid-channel. In this area the Troutdale formation is covered with a layer of fine to medium sand 90 to 100 ft thick. It was the variable depth of the Troutdale which determined the two types of foundations and the corresponding to the two cofferdam systems.

Jan 1, 2013

By Eric S. Lindquist

High groundwater levels combined with variable soil and rock profiles present challenges to the design and construction of deep excavation support systems. Increasingly, secant piling techniques are the preferred technical solution for shoring in these cases. Recent developments in drilling equipment, tooling and procedures allow cost-effective construction of deep, overlapped pile systems to tight tolerances in extremely difficult ground conditions. This paper summarizes critical design considerations for secant pile shoring systems, detailing recent advances in installation procedures and verification techniques that allow secant piles to be used for an expanding range of project conditions. Technically- and commercially-viable secant pile shoring designs require that stringent drilling tolerances be achieved in order to successfully provide combined structural support and groundwater cutoff systems, particularly for unreinforced circular secant pile shafts acting in ring compression. Modern drill rigs and tooling can advance fully cased shafts in geotechnical conditions which range from cohesionless soils below the groundwater table to hard rock, within a single drillhole. Down-hole instrumentation provides verification that tolerance requirements are met and allow secant pile shoring to be used at sites previously considered unacceptably risky. In California, secant pile shoring systems are being used for excavation depths of over 100 ft (30 m) on projects with challenging site conditions. Two case studies are presented detailing severe geotechnical conditions and excavation depths which represent the regional state of practice in secant piled excavation support. These projects provide real world examples of the design, construction and construction verification techniques that permit secant pile shoring to be used in more demanding geotechnical conditions and to greater depths than ever before.

Jan 1, 2011

By Frederick C. Rhyner

Drilled shafts have become an economical foundation choice for bridges in the northeast United States, especially when they can be constructed over water without the use of cofferdams. For the Boscawen-Canterbury Bridge over the Merrimack River in New Hampshire, an unusual design was used to avoid the use of cofferdams and avoid the need for pier caps at the waterline. This design used a pair of integral drilled shaft ? columns to form a bent type of substructure for support. Drilled shafts were 8-foot diameter, about 90 feet deep, with 16-foot long rock sockets. These are integrally constructed with 6-foot diameter reinforced concrete columns extending 37 feet from the waterline to the superstructure. Design load cases focused on lateral loads from ice flows, stream flows, wind and seismic events. Alternative analyses using different methods were made to check the design results. This paper discusses the subsurface conditions, design of the drilled shafts and columns, rebar and joint detailing issues, and construction of the drilled shafts.

Jan 1, 2004

By Ahmad F. Souri, Murad Abu-Farsakh

"In this study, the static lateral resistance of vertical and battered pile groups was analyzed using 3D finite element analysis. The battered pile group finite element model was verified using the results from a case study performed on the M19 pier foundation of the I-10 twin span bridge in Louisiana. The vertical pile group model was created by adjusting pile inclinations of the verified battered pile group model. The finite element models utilized nonlinear constitutive models for materials behavior and a soil-pile interface model. The results showed that the battered pile group had greater lateral resistance than the vertical pile group with 60-70% lower pile cap displacement. The largest lateral load share was found in the middle rows in the battered pile group, while it was in the leading row for the vertical. The soil resistance profiles showed that the vertical pile group mobilized greater soil resistance compared to the battered pile group.INTRODUCTIONThe lateral resistance of a pile-soil system depends on both pile stiffness and soil reaction. The soil reaction is a nonlinear function of deflection, depth, pile stiffness, and soil stiffness and strength. The lateral capacity of single piles is evaluated at the maximum deflection limit, and can be predicted using established methods such as the p-y curve method (e.g., Matlock 1970, Reese et al. 1974), elastic solution by Poulos and Davis (1980), the strain wedge model (Ashour et al. 2004), and the finite element method (e.g., Yang and Jeremic 2002, Comodromos and Pitilakis 2005, Isenhower et al. 2014). For pile groups, the lateral capacity of a pile-in-group is less than the isolated single pile case because the soil in front of the pile-in-group is weakened by the overlap of stress zones from surrounding piles. The latter is referred to as the shadowing or group effect (Fig. 1). Prediction of the lateral capacity for pile groups is based on the p-y curve method for single piles with the use of empirical factors called “p-multipliers”. The p-multipliers accounts for the shadowing effect, and are a function of pile-pile spacing and soil type (e.g., Brown et al. 1987, 1988, McVay et al. 1995). Moreover, the lateral capacity of pile groups is also influenced by vertical load, piles arrangement, and slenderness ratio (e.g., Rao et al. 1998, Patra and Pise 2001, Ilyas et al. 2004, Hussien et al. 2012).Battered piles refer to piles installed at an angle with respect to the vertical to increase their lateral capacity. The greater lateral resistance is achieved by the additional axial reaction in the pile. Battered piles are called “negative battered” when inclined in the load direction, and “positive battered” when inclined opposite to the load direction (Fig. 1). Previous studies concluded that the lateral resistance is highest in positive battered piles followed by negative battered and vertical piles, respectively (Murthy 1964, Meyerhof and Yalcin 1993, Zhang et al. 1999)."

Jan 1, 2017

By Thomas L. Vande Voort

The strategic plan for bridge engineering issued by AASHTO in 2005 identified extending the service life and optimizing structural systems of bridges in the United States as two grand challenges in bridge engineering, with the objective of producing safer bridges that have a minimum service life of 75 years and reduced maintenance cost. Material deterioration was identified as one of the primary challenges to achieving the objective of extended life. In substructural applications (e.g., deep foundations), construction materials such as timber, steel, and concrete are subjected to deterioration due to environmental impacts. Using innovative and new materials for foundation applications makes the AASHTO objective of 75 years service life achievable. Ultra High Performance Concrete (UHPC) with compressive strength of 26,000 psi (180 MPa) and excellent durability has been used in superstructural applications but not in geotechnical and substructural applications. This paper explores the possibility of using precast, prestressed UHPC piles in future bridges. An H-shaped UHPC section, which is 10-in. (250-mm) deep with weight similar to that of an HP10×57 steel pile, was designed for constructability and economical reasons. Instrumented UHPC elements were cast to conduct large-scale field tests. In the field, two UHPC piles have been successfully driven in glacial till clay soil and load tested vertically. Test results, durability, drivability, and other material advantages over normal concrete and steel indicate that UHPC piles are a viable alternative to extend the life of bridge structures.

Jan 1, 2008

By Mark R. Svinkin

Regulations are needed to keep construction vibrations in tolerable limits. The existing regulations were developed for low-rise residential structures, but they are incorrectly used for different super and underground structures. The existing regulations cannot prevent most of harmful vibration effects on sensitive devices, people and structures from construction and industrial vibration sources. It is important to determine the areas of application of the existing regulations and bring attention to the necessity of measurement of the structural responses for assessment of vibration effects on structures. For multi-story residential, commercial and industrial buildings, the frequency-independent safe limit of 51 mm/s (2 in./s) can be chosen for the peak particle velocity of structural, not ground, vibrations. Specifications for construction operations with dynamic sources have to consider specifics of each construction site. Preventive measures can be used to mitigate harmful vibration effects on various structures and settlements in sand and clay soils.

Jan 1, 2006

By Anuj K. Singh, Shuvranshu Rout, Manos De

"Foundation for tracks of coke transfer car and dust extraction pipe was designed as series of isolated foundations spaced at 11.0m along length of coke oven battery resting on soil at depth of 2.5m. In one region the foundations are close to adjacent 12m deep underground junction house. Five foundations in this zone were constructed on backfilled soil without proper compaction instead of engineering soil fill or concrete fill. The foundations settled under loads and the supported frame structure tilted after equipment erection and during trials endangering the safety of the structure and equipment operation. The distorted structure had to be rectified in-situ by arresting settlement. In order to stabilize the foundation and supported structure the supporting soil had to be strengthened in situ without any dismantling, reconstruction and adverse effect to equipment operation. This paper presents the case study on the evaluation of defects for the foundation failure and analysis of the problem, proposed rectification of the situation by appropriate soil stabilization scheme, monitoring of the stabilization operations and verification of effectiveness of the rectification work by measurement of settlements. The implemented solution has ensured safety of the structure and equipment without any adverse impact on normal operation.INTRODUCTION AND BACKGROUNDNew Coke Oven Battery was being installed for an integrated Steel Plant. The hot coke from oven is pushed out after completion of coking process through a coke transfer car onto a hot coke receiving car. The coke transfer car runs on rail track parallel to the line of ovens forming the coke oven battery. One rail is supported on the structure of the operating platform of the battery and the second rail rests on independent structure of track beams. A large diameter pipe for extraction of the dust emitted during coke pushing operation is also supported on the same structure that supports the track beams. The entire structure rests on columns spaced at approximately 11.0m along the length of the battery. The columns transfer load to ground through individual foundations resting on competent subsoil strata.Two sets of foundations for the rail track beam support and dust extraction pipe support are adjacent to deep underground junction house of coke carrying conveyor. The depth of the pit for the junction house is 12m. The layout and arrangement of the foundations in this region around the junction house (JH-1) is shown in the “Figs. 1a, 1b”."

Jan 1, 2017

By Ryan Higbie, King Chin, Matthew Anderson, Mike Huggins, Rian Johnson, Dave Sinsheimer

"The Permanent Canal Closures and Pumps (PCCP) project is the capstone piece of New Orleans’ extensive hurricane risk-reduction system constructed following Hurricane Katrina. The project consists of three discrete pump stations and flood gates on the shore of Lake Pontchartrain which provide a storm surge barrier and pump rainwater from the City of New Orleans’ primary drainage canals. The depth of the pump station structures ranged between 39 and 45 feet below sea-level. USACE developed the PCCP project for design-build delivery; granting the project team latitude to develop innovative, cost effective solutions for the project. The use of OPEN CELLTM cofferdams to construct the pump station structures was one such innovation. OPEN CELL structures utilize the strength of the retained soil to anchor cellular sheet pile face arcs; allowing a free-field of construction within the cofferdam. This cofferdam design did not require ground improvement or dewatering around the perimeter of the cofferdam. The free-field cofferdams streamlined construction and large equipment installation within the structures with no encumbrance from internal bracing. Meticulous force-based design, soil-structure numerical modeling, and physical testing were all techniques used to present and gain USACE acceptance of the design on this vital element of the work.PROJECT DESCRIPTIONThe Permanent Canal Closures and Pumps (PCCP) project is the capstone piece of the City of New Orleans’ extensive hurricane risk-reductions system constructed following Hurricane Katrina in 2005. The project encompasses three separate pump stations and floodgate structures located at the mouths of three outfall canals (17th Street, Orleans, and London) on the south shore of Lake Pontchartrain. These three canals, running from the south to north, act as the primary conduits for discharging water from the New Orleans area. Prior to Hurricane Katrina, these canals were operated with pump stations two to three miles upstream of the mouths at Lake Pontchartrain. This left long stretches of levee on each side of the canals exposed to storm surges entering from the lake. Three levee failures occurred along these canals during Katrina; two at London Canal and one at 17th Street Canal. The failures resulted in major flooding of the surrounding neighborhoods, significant damages, and loss of life.Following initial canal levee repairs after Hurricane Katrina, USACE, in partnership with the Louisiana Coastal Protection and Restoration Authority (CPRA), took action to move the line of flood protection to the mouths of these three canals at the edge of the lake. By cutting off the storm surges from Lake Pontchartrain at the entrance to the canal, over ten miles of canal levee would no longer be exposed to storm surge water elevations, significantly decreasing the risk of failure."

Jan 1, 2017

By Jom Gentry

Acrylamide chemical grout (C3H2NO) has been successfully used for over 50 years to control groundwater and stop infiltration. This paper will address three unique projects involving the control of groundwater with each study providing special circumstances and geological conditions: encapsulation of radioactive hazardous waste in the United States, a tailings dam for a large copper/gold mine in Argentina and 27 miles of leaking subway in Canada. The primary reasons for selecting acrylamide grout were based on the following characteristics: thinnest chemical grout on the market, a true solution grout which contains no suspended solids in the blended product, flexible gel set times, and a 362 year half-life in soil as determined by the U.S. Department of Energy.

By Timothy C. Siegel

In response to a solicitation for ground improvement for the construction of a new hospital in Owensboro, Kentucky, the team of Berkel & Company Contractors and Dan Brown and Associates PC designed and installed lightly reinforced cast-in-place piles (known commercially as Cast-in place Ground improvement Elements or CGEs) as part of a composite ground system. The concept of the design is that the structure load is shared between the piles and the soil subgrade. The load sharing is controlled (to some degree) by the placement of a cushion between the pile head and the bottom of the overlying spread foundation. In an effort to confirm the design principles and to better understand the behavior of composite ground, the design-build team performed plate load tests on ground with a single CGE and with a group of CGEs. The small plate test (on ground with a single CGE) characterized the stiffness of the cushion. The large plate tests showed that the cushion will distribute the applied load to the CGEs and to the soil subgrade between the CGEs. On the basis of the plate tests, it was concluded that the plate stiffness can influence the test results. The use of a concrete layer was effective at supplementing the plate stiffness. The cushion was shown to be an important component of a composite ground system by allowing mobilization of the soil subgrade resistance and avoiding a stress concentration at the tops of the CGEs that would otherwise be present if the spread foundation and piles were rigidly connected. Because the composite ground system engages the resistance of the soil subgrade, the structural demand is reduced and consequently there is a potential for savings when compared to a conventional pile foundation. Several foundations for the new Owensboro hospital are being monitored for vertical movement during construction of the superstructure that will extend through 2011. At the time of this paper (mid 2011) the settlement of the foundations due to only part of the structural load (primarily the structural steel) has been negligible.

Jan 1, 2011

By Ashutosh S. Dhar

Cast-in-place piles were examined in this paper from the viewpoints of construction quality, axial capacity, and load-displacement responses. The results of ten 450 mm diameter (18? f) bored piles, installed in a soil deposit of silt to medium dense sand using the method of percussion drilling, were tested under static loads. The results of the pile load tests were used for evaluation of various design methods of calculating pile capacity. The study revealed that the design methods based on the concept of critical depth underestimated the ultimate skin fiction. Thus, the applicability of the critical depth concept for design of bored piles under the soil condition considered may be unreliable. The estimated skin friction factor, ß, was too low in these methods. The Tomlinson method and the Neely method provided the best prediction of the ultimate skin friction. The methods used for calculating end bearing resistance were found to provide a conservative estimate of the resistance. During pile load tests, a settlement of 5 to 6 mm was required for full mobilization of skin friction for the piles in loose sand, while larger settlements (> 10 mm) were required for piles in denser soil. The ultimate skin frictional resistance was observed to be low for piles in loose sand.

Jan 1, 2006

By S. Ali Bastani, Ashley Varni

Design acceleration response spectra (ARS) are directly correlated with dynamic forces and estimated dynamic bridge displacements, which make them a critical aspect of dynamic bridge design. Nonlinear site response analyses are performed for a 1,400-linear-foot bridge site with a SC soil profile at the sides and a SF soil profile in the middle to evaluate the soil profile effects on the bridge analyses. One-dimensional seismic response analysis is commonly performed for site-specific response analysis. SHAKE or similar one-dimensional total-stress equivalent-linear approaches have been used since the 1970s. However, the equivalent linear method has deficiencies when the subsurface soils are susceptible to strain softening. Therefore, various assumptions are made when using the equivalent linear method by practitioners to estimate the SF soil profile site response. With recent advancements in constitutive models, effective stress models have become more popular. Although the effective stress models are generally more complicated and require additional input parameters, they shed further light on the liquefaction mechanism and its effect on the surface ARS. An equivalent-linear one-dimensional seismic response analysis and a non-linear effective-stress seismic response analysis, using DEEPSOIL, were performed to evaluate the ground surface ARS for a proposed bridge site in Orange County. The soil shear strengths were estimated based on cone penetration test results using empirical relationships. The shear modulus degradations (backbone curves) of soil layers were adjusted to match the estimated soil strength at failure. The ARS curves developed from each method were compared to determine the most suitable method for estimating a site-specific design ARS curve for a liquefiable site. Considering that the bridge abutments and the outer bents are founded in bedrock, while the middle bents are founded in liquefiable soils, ARS curves were created for each subsurface condition. Taking into account limitations of the structural analysis software, recommendations were made to combine the multiple ARS curves into a single ARS curve for the structural bridge design.

Jan 1, 2018

By Mostafa Mossaad, Ali Helwa, Manal Salem

Support of excavation (SOE) design practice tends to model SOE elements using two-dimensional (2D) analyses to avoid the complexity associated with three-dimensional (3D) analyses. Such practice overlooks soil arching in the horizontal plane and prevents designers from accounting for elements such as capping beams as part of the statical system. This study simulates square excavations supported by cantilever slurry walls in dry cohesionless soil using 2D and 3D finite element (FE) models. First, side support wall behavior is compared from 2D and 3D FE models for variable excavation length to depth (L/H) ratios. Second, the effect of slurry wall lateral bending stiffness on wall behavior is studied by modeling the wall using plate element with isotropic and anisotropic wall stiffness. Finally, the sensitivity of cantilever wall behavior to the presence of capping beam is illustrated. The study concludes that unbraced excavations with L/H ratios greater than 5 almost resemble plane-strain conditions. Slurry walls are better simulated in 3D FE models by dividing the plate element into discrete panels or by assigning anisotropic bending stiffness to the plate element. Finally, the presence of capping beam affects the behavior of cantilever walls resulting in reduction of deflections and redistribution of bending moments. INTRODCUTION Support of excavation (SOE) design practice ranges in complexity from conducting simple hand calculations to performing three dimensional numerical modeling depending on several factors among which is the geometry of the design problem. This paper addresses walls that are designed using numerical modeling, and discusses the factors governing the choice of the most suitable modeling approach. It has been believed for a while that modeling excavations using 2D numerical models would lead to a more conservative solution, which turned out to be incorrect in specific cases. This paper attempts to describe cases where 2D finite element modeling could be on the conservative side and other cases where it could be less conservative than the more complex 3D modeling.

Jan 1, 2018