Search Documents

By M. J. Preim

Two case histories are presented on the evaluation of static bearing capacity of piles driven in soils that exhibit time dependent strength changes. Under consideration are a steel and a concrete pile driven into soils generally consisting of silty and clayey fine sand. Pile dynamic measurements and analyses were performed on both piles during initial installation, and also during restrike one week later. This information was used to predict each pile's long term capacity (defined as 14 days after initial drive), which was then compared to that measured with a static load test. Agreement between predicted and measured capacities were remarkably good, with an average error of only 4.5 percent. Two weeks after driving, total pile capacities were three times those at the end of drive. If only the skin friction was considered, however, it increased by an average factor of 16. The increase in pile capacity was determined to be linear over the time period considered.

Jan 1, 1989

By Magnus Ruin

The dry deep mixing method for stabilization of soft soil has been used in the Scandinavian countries for 25 years. The typical application has been stabilization of soft inorganic clay. Today the method is used more frequently in organic soil with good results. The Limix System, introduced in the USA by Hercules Grundläggning AB and TREVIICOS Corporation, is a cost-effective dry deep mixing method used to stabilize most types of soft soil. This paper presents the general principles of stabilizing organic soil with the dry mix method and two case histories of soil stabilization projects in organic soil. Between October 2000 and June 2001 the Limix System was used in England to stabilize soft organic alluvium at the Channel Tunnel Rail Link, Contract 440. During year 2000 the Limix System was used in soft organic soil in Holland near the Groene Hart Tunnel entrance to support trench excavations for slurry walls and concrete barrettes.

Jan 1, 2001

By Jay L. Hodkinson

Replacement of an aging twin span river crossing in Vermont required a temporary bridge to accommodate traffic during construction. Soils beneath the temporary approach embankment consisted of very soft organic clayey silt underlain by interbedded, loose alluvial fine sand and silt/clayey silt. Reinforcement was required for the southern temporary approach embankment to limit settlement and to increase global stability factors of safety. A ground improvement design was developed using Rammed Aggregate Pier® reinforcement and was included in the contract documents as an FHWA Category II Experimental Feature. Instrumentation intended to document the performance of the supported embankment was installed. Piers were then constructed and monitoring commenced as embankment and bridge construction occurred. Weekly instrumentation data reports indicated continuing excess pore water pressure, settlement, and lateral deformation of the subgrade soils as the embankment and temporary bridge abutment was constructed. In response to the unanticipated monitoring results, further investigation indicated that significant deviations from the conditions and basis upon which the ground support design was developed were made during construction. This paper discusses these deviations and their specific impacts to embankment support performance, how these deviations occurred, the role that the ground support system played in maintaining global stability, measures taken to limit further detrimental impacts to the embankment, and provides recommendations for contract document preparation and construction oversight to prevent similar situations from occurring on future projects.

Jan 1, 2011

By Jared M. Green

This paper presents the wall stabilization design and implementation for a 541 linear ft masonry and concrete gravity-type retaining wall flanking the west perimeter of a 7.37 acre parcel in Bronx, New York. This paper will discuss the results of static and dynamic stability analyses performed for the pre- and post excavation phases for the proposed 300 ft wide open-cut of up to 14 ft of contaminated soil below the toe of the retaining wall. The wall stabilization consisted of over 74 inclined drilled and grouted anchor dowels, and 55 tiebacks drilled and grouted to the underlying mica schist bedrock. Three over-lapping rows of jet grout columns were chosen as the foundation solution for the existing retaining wall. This paper focuses on the design, construction and performance of the jet grout curtain wall. The jet grout wall served three purposes: 1) underpinning and excavation support for the removal of contaminated site soils, 2) permanent hydraulic barrier, and 3) resistance against a deep seated failure within the thick clay layer present at the site. The originally designed jet grout wall had unexpected negative effects to the existing retaining wall. The jet grouting program was modified while the Observational Method (Peck 1969) was employed to keep wall movements to a minimum. This paper discusses the diagnostic methods used to determine the cause of retaining wall movement; the implementation of a remedial ground improvement program; the modification to the jet grout installation procedure; and the ultimate performance of the jet grout wall.

Jan 1, 2011

By Jim Steding

L.G. Barcus and Sons, Inc. recently completed a three-phase project for the expansion of Presbyterian Hospital in Albuquerque, New Mexico for McCarthy Construction Co., the Construction Manager for the project. It was a challenge that allowed Barcus to demonstrate many of it's strengths. Safety of people and property, restricted access, low headroom conditions, extensive planning to maintain hospital operations and a tight schedule were all key elements affecting the successful installation of the Augered Cast-In-Place Piles. Phase I began with installing and performing a 450-ton pile load test on an 18-inch diameter Augerpile 65 ft long. The load test was installed and performed directly in front of the Emergency Room entrance. Space was limited and the E.R. had to remain open with uninterrupted ambulance access. The results of the load test were outstanding. In fact the test pile performed so well that some of the job piles were shortened from 75 ft long to 65 ft long. [ ]

Jan 1, 2003

By P. Dupeuble

Diaphragm walls, owing to their method of construction are discontinuous structures. A new technology for the construction of joints between panels has been developed. This new process allows for the construction of diaphragm walls with mechanical and watertight continuity.

Jan 1, 2010

By J. P. Welsh

Ground Modification construction is rapidly evolving in the United States. An assessment of the construction status of Ground Modification methods with their dates of introduction and general acceptance in the United States is summarized. Seven of these techniques are discussed in depth with short case histories; namely, Dynamic Deep Compaction, vibro-compaction, vibro-Replacement, chemical grouting, compaction grouting, slurry grouting and jet grouting. Additional case histories are presented to illustrate the trend of combining Ground Modification techniques to solve specific site problems.

Jan 1, 2010

By Ian Vaz, Takefumi Takuma

"The New Orleans area has been repeatedly flooded by major storms and hurricanes since its French colonial era. After severe flooding in May 1995, the U.S. Congress authorized a massive flood protection project called the Southeast Louisiana Urban Flood Control Program (SELA) in 1996 to improve interior drainage in Orleans, Jefferson, and St. Tammany parishes. However, the project was not fully funded before the landing of Hurricane Katrina in 2005 and Hurricane Rita, which breached many of the area’s levees and flooded 80 percent of the city. Finally, the project was fully funded in 2008 and has been worked on towards its 2017 completion. Another large project simultaneously worked on in the area is the Hurricane and Storm Damage Risk Reduction System (HSDRRS). This system was designed for a 100-year level of flood risk reduction. One particular project within the HSDRRS rendered successful due to an unconventional method of pile driving that was utilized to install sheet piles to reinforce an existing concrete I-wall. This paper will discuss how and why this non-vibratory method of sheet pile installation allowed the project to be successfully completed ahead of schedule.INTRODUCTIONSteel sheet piles were utilized on many of the SELA and HSDRRS projects for permanent cutoff walls under concrete I-walls or T-walls or for temporary earth retaining walls of drainage structures. Although the SELA Project was established in 1996 after severe flooding the year before, hardly any work was done on it until the two catastrophic storms Hurricanes known as Katrina and Rita triggered its revival. These two hurricanes also triggered the HSDRRS soon after the storms’ devastation. The SELA project authorized to improve interior drainage systems while the HSDRRS project was authorized to raise or restore levees and floodwalls mainly along Lake Pontchartrain, the Mississippi River, and Lake Borgne in addition to other areas. Figure 1 shows the SELA Projects that have been completed, are still under construction, or approved for construction. The projects fully highlighted in yellow within the map specified the press-in piling method. These improvements included drainage systems, pump stations, surge walls, and outfall canals as enhanced protection for future storms similar to Hurricane Katrina that caused so much damage by inundating the New Orleans area in August and September 2005 respectively (Facts and Figures, 2012). The completion of these projects were the responsibility of the U.S. Army Corps of Engineers, New Orleans District.Due to the fact that many of the projects were in densely populated areas, the Army Corps of Engineers specified a non-impact, non-vibratory press-in piling method for driving and extracting sheet piles for many of the projects to mitigate noise and vibration impacts. The soft soil conditions in the New Orleans area was also a contributing factor in the Army Corps of Engineers’ decision to specify this piling method due to the risk of settlement for existing historical as well as modern structures. In addition, there were other projects that elected to use the press-in method without any contractual requirements. One of these projects was the Inner Harbor Navigational Canal Reach II Emergency Interim Repair which was part of the HSDRRS project that has been under construction since its authorization in 2005 (Facts and Figures, 2012)."

Jan 1, 2017

By Walter I. Paniagua

A housing complex of 76 buildings is being constructed in the city of Morelia, in western central Mexico; the buildings are 5 levels high, with a shallow concrete slab foundation. Soil conditions include a soft clay stratum, with up to 8 m depth, in a highly seismic area. Pile foundations and micro-piles were considered, but discarded due to economic factors. The alternative of soil improvement with rigid inclusions was used. An FEM (Finite Element Method) analysis was conducted to determine the diameter, spacing, length and arrangement of the inclusions. Construction was implemented with traditional methods: soil boring, and mortar tremied with pipe and the aid of a sock to contain the material (no steel reinforcement was used). So far, 46 buildings have been built, and level measurements for 18 buildings have been recorded since 2006, with resulting good behavior in both total and differential settlements.

Jan 1, 2008

By Daniel Mageau

Ground freezing has been used for over 100 years to provide shoring and ground water cutoffs for hundreds of projects worldwide, including drilled shafts, tunnels and cofferdams. Typically, these cases involved difficult soil/water problems where ground freezing was likely the only solution. This paper discusses a recent ground freezing project where a frozen soil wall was used for a more conventional problem. A 4-foot-thick frozen soil wall was used to provide shoring and groundwater cutoff for a 20-foot-deep excavation during construction of a cast-in-place concrete storm water detention vault. The site is located along the northbound on-ramp to I405 from westbound SR522 in Woodinville, Washington. The frozen soil wall was successfully formed in soils consisting of till fill over soft organic silt and loose saturated sand in about 3 weeks. The depth to ground water varied from about 4 to 8 feet over the site. The unfrozen soil inside the frozen soil wall was excavated vertically to the frozen soil boundary. The vertical excavation remained open for approximately 2 months with no dewatering required. On one side, fully-loaded dump trucks and other construction equipment operated within 6 feet of the wall face with zero wall movement. This paper addresses the construction issues related to installation and operation of ground freezing shoring. The overall wall performance of the frozen soil wall as well as basic geotechnical design issues are also discussed.

Jan 1, 1998

By Kazuyuki Matsuzawa

A series of plate loading tests were carried out on a loam ground in order to investigate the influences of the plate size and the loading rate on the observed load-settlement relations. Two circular plates having diameters of 0.3 m and 1.0 m were used. Three types of loading methods were employed; 1) static cyclic maintained load test, 2) static continuous load test, and 3) rapid (dynamic) plate load test. An interpretation method called non-linear damping method was used to estimate a static load-settlement relation from the rapid plate load test signals. The derived static load-settlement relations match well with the measured results from the static load tests.

Jan 1, 2006

By G. G. Goble

Significant progress has been made in the past decade in determining the load bearing capacity of pile foundations. Developments in the means of prediction of pile capacity as limited by soil strength have been substantial, particularly in the use of dynamic methods. The use of currently available equipment, analytical procedures, and practices in the field, will often produce material economies on a job by allowing increased loads with proven factors of safety. This approach justifies the minimum number of piles required for a safe foundation in a wide range of job sizes and soil conditions. To avoid exposing the reader to excessive detail in the body of this paper, technical topics have been covered more thoroughly in several appendices. I. Wave Equation Analysis of Piles Appendix A II. Dynamic Monitoring and the Pile Driving Analyzer Appendix B III. Case Method Capacity Calculation Appendix C IV. Case Pile Wave Analysis Program Appendix D 1 Preliminary Analysis In designing driven pile foundations, there must be a close relationship between design, construction control procedures, driving practices, and the size of the job. Small commercial buildings or residences involving loads that are only a fraction of the pile capacities do not justify the expense of detailed design processes or elaborate construction controls. Nevertheless, some preliminary analysis of the job requirements and a limited subsurface investigation must be made to understand existing conditions and the possible foundation solutions. In other words, it is necessary to determine that driven piling is the best overall choice of foundation.

Jan 1, 1988

By Tracy Brettmann

The Highway 146 Bridge Expansion Project across the Clear Creek Channel in Houston, Texas was designed on driven precast concrete piles. However, during construction, the piles along one side of the bridge along the main channel encountered obstructions and couldn’t be installed. These obstructions turned out to be the remnants of a previous bridge foundation at this location, which was unknown to the designers since that bridge had been demolished 40 years ago. Those old foundations were massive 20 ft by 40 ft (6 m by 12 m) pile caps 11 ft (3.3 m) thick supported on precast concrete piles 37 to 55 ft (11 to 17 m) long. The foundation re-design for these locations involved installing a single 78 inch (2 m) diameter drilled shaft up to 125 ft (38 m) long to replace the originally planned driven pile supported pile cap. The drilled shafts would need to be installed within very tight tolerances since they were supporting a single bridge column directly above it. In addition to drilling through the obstructions, this work would need to be completed from barges in 30 ft (9 m) of water capable of dealing with both the current and tides affecting this area. The shafts were installed using a multi-step process. The first step involved coring a larger diameter 100 inch (2.5 m) hole through the reinforced concrete pile cap and removing the concrete inside. This was followed by the installation of a 72 ft (22 m) long permanent casing to and removing the soil and existing precast piles inside. Finally, the drilled shaft excavations were advanced to the completion depths (uncased) using bentonite slurry as the support fluid.

May 1, 2022

By Maurice Bottiau

"Abstract When addressing the performance of deep foundations, many parameters play a role, from adequate soil investigation to performance monitoring and testing. The correct understanding of pile construction, though, remains crucial. After a long period of empirical design and regulations, the last decades have been the ones of theoretical considerations and extensive codes writing. The interaction between technology and design, however, still plays a determinant role. The introduction of hydraulics and the exponential increase in available power on one hand, the miniaturization and the introduction of electronics in control and monitoring systems on the other hand have exerted a major influence on new foundation systems or the evolution and control of existing systems. It appears important to try to take execution related parameters and their control during execution more deeply into account when assessing the final result of the deep foundations and the achieved level of safety and reliability. In this contribution, we will try to analyze how systems, equipment and pile production monitoring and testing can influence the pile performance, and if/how this influence could/should be translated in adapted safety or installation factors. This analysis will run through different categories of piles: driven, augercast and displacement auger piles and bored piles. INTRODUCTIONThe global performance of a deep foundation depends on different aspects (Poulos, 2003):1. Ground investigation2. Design and analysis3. Construction4. Testing5. Performance monitoring6. Remediation and performance enhancementThis paper intends to address the importance of pile construction and the control of it on the final performance of the pile-group of piles. There has been an increasing interest for theoretical analysis over the last 20 years, followed by an increasing impact of regulation and codes. Without denying the importance of the latter, the author wants to point out how installation procedure and project specific parameters can largely influence the reliability of the deep foundation. In this context, detailed and prescriptive standards can miss their objective of intended improvement of accuracy and reliability, but even worse they can adversely impact engineering judgment. In today’s construction world, it is possible to gather installation information which can be of outmost importance for the final deep foundations performance. Therefore, the increase or decrease of installation reliability through adequate pile testing and performance monitoring should be emphasized and should be taken into account in the codes. This is the case already in most advanced codes, but in a limited and insufficiently refined way. After reviewing how codes deal with this issue today, we will show some recent examples of unexpected results due to pile installation. We will try to put these examples into a broader perspective by highlighting some reference and/or recent literature considerations. Finally we will try to summarize how pile testing and installation documentation can increase reliability and attempt to open the debate on how codes could/should allow for more engineering judgment."

Jan 1, 2014

By Mark DeSalvatore

Currently, at Caltrans, the Office of Structure Design is carrying out an extensive seismic retrofit program involving transportation structures throughout California. The goal of the retrofit program has been to upgrade existing transportation structures to meet the present seismic codes and anticipated loads that are generated during a seismic event Part of the retrofit program involves retrofitting existing structure foundations when required. To determine if the foundations of a specific structure need to be retrofitted, an engineering analysis of the existing foundations has to be done. If the engineering analysis of the structure foundations determines that the foundations will not meet the load carrying demands required by the structural engineer, the existing foundations are then retrofitted. The retrofit projects that require foundation modifications can be separated into two general cases. The first case comprises structures where the original designs will not meet the demands of the present seismic design code. In this case, the existing foundations are not capable of providing the load capacities the current seismic code requires. The second case consists of structures where the retrofitting of the superstructure will increase the required load carrying capacity of the existing foundations during a seismic event In this case, the anticipated load demands on the existing foundations are greater than the foundations are capable of providing. For either of the cases listed above, the present strategy for increasing the capacity of the existing structure foundation consists of installing tiedown anchors or large capacity piles to provide the required resistance to seisraically induced loads.

Jan 1, 1993

By S. T. Kok

This paper presents a case study in West Malaysia for passive piles failure in very soft marine clay in open excavation. In this particular case, the thickness of the very soft marine clay ranges from 5 m to 7 m (16 ft to 23 ft) from the ground surface. Preliminary site investigation reported SPT ?N? value of zero for the very soft marine clay. The design was based on a deep foundation utilizing driven piles to support the superstructure. During pile cap construction, the piles were subjected to uncontrolled open excavation, inducing bending moment in the piles, resulting in some cracked and broken piles. Analyses were carried out using an existing three-dimensional finite element code with a non-linear soil model to predict the response of these piles during excavation. Finally, the predictions of pile responses during excavation were compared satisfactorily with the observed results.

Jan 1, 2009

By Ganesh Kumar S.

"Soil reinforcement using stone columns is one of the well-developed ground improvement techniques for soft clay deposits. The load carrying capacity can be further improved by encasing it with geosynthetic material around the column which offers effective lateral confinement, prevents column contamination with improved drainage and strength characteristics. Improvement of undrained shear strength using vacuum consolidation is a type of hydraulic modification technique in which negative pore pressure will be developed which increases the effective stresses in soil without changing the total stress. The improvement in effective stress resulted in improved undrained shear strength of surrounding soil. In this research work, combined geosynthetic encased stone column and vacuum treatment method is examined for improving of extremely soft clay soils. The improvement in the time rate of consolidation and load carrying capacity of stone columns after vacuum treatment was studied using experimental investigations. It was observed that both load carrying capacity and stiffness of the encased stone column increased significantly with vacuum application. Also, application of vacuum accelerates rate of primary consolidation settlements. With this reduction in time, the construction activity can be accelerated which makes the project economically beneficial.INTRODUCTIONThe rising demand for the land for country’s infra-structure compels the engineers to work with even soft clay deposits which are not suitable for construction activities. As these soils have low bearing capacity and excessive settlement characteristics, ground improvement methods will be required before commencing construction. Among all available treatment methods, soil reinforcement and hydraulic modification technique are well-known popular techniques for its reduction in time required for consolidation settlement with improvement in load carrying capacity. When stone columns are used as a reinforcing member, it creates drainage with improves bearing capacity (Greenwood, 1970; Mitchell & Huber, 1983). However, the limitation includes lack of lateral confinement in very soft clay deposits, possibility of contamination, reduction in drainage path all which leads to the failure of stone columns (Mckenna et al, 1975). To overcome these limitations, encasement using geosynthetic material was adopted around the column which offers better lateral confinement, prevents intrusion of finer clay particle inside the column and provides effective drainage path with improved load bearing capacity characteristics (Van Impe, 1986; Raithel et al. 2005; Short et al. 2005; Borkemper et al. 2006; Murugesan & Rajagopal 2010; Kumar et al. 2014)"

Jan 1, 2017

By Brian Langdon

The DRIVEN GROUT PILE was developed in 1989 by DeWitt Construction, Incorporated. This piling essentially consists of a cost-in-place concrete piling that reacts on a steel boot that is driven to bearing. This report will describe the driven grout pile, its background and its installation. The advantages and disadvantages of this system are also discussed. Finally, the results of actual field installations are presented and discussed. BACKGROUND The DRIVEN GROUT PILE was developed out of a need for a low-cost high capacity piling (100 ton) that could be installed with ordinary pile driving equipment. This search was motivated by attempting to incorporate the material economy of an auger-cast piling with the "empirical load test" of a driven pile. Typically, the least cost material for piling in the 100 ton range is concrete (grout). A grout shaft with minimal reinforcement can withstand a compressive load of 100 tons for a material cost in the range of $6.00 to $8.00 per lineal foot. A pipe piling with a capacity of 100 tons has a unit material cost ranging to $13.00 per lineal foot. The marriage of these two advantages resulted in the DRIVEN GROUT PILE. A pile that utilizes the economy of a reinforced grout shaft and has the loading confidence of a driven pile.

Jan 1, 1990

By A. Eslami

In recent development of piled raft design, the contribution of both raft and piles to tolerate the loads is taken into account, depending on the stiffness and contributions of involved elements i.e.; piles, raft and surrounding soil. The piles are usually required not to ensure the overall stability of the foundation but to act as settlement reducers. One alternative method of foundation design is therefore to introduce piles purely as a means of improving or enhancing the stiffness of the base soil by structurally disconnecting the piles from the raft. In this paper, two and three dimensional finite element analysis of disconnected pile-raft systems are performed on three case studies including a 12-storey residential building in Iran, a 39-storey twin tower in Indonesia, and the 256m height of Messeturm tower in Frankfurt, Germany. The analysis include different geometrical parameters, e.g., pile spacing and embedment length, arrangement and raft thickness for foundation system to obtain the optimized design functions and to clarify the role of each parameter and method of analysis. The parametric study results and comparison to a few field measurements indicate that by concentrating the piles in the central area of the raft foundation leads to the optimum design with the minimum total length of piles. This achievement can be considered as a criterion for project cost efficiency. On the other hand, disconnected piled-raft systems can significantly reduce the settlements and raft internal bending moments. Finally, the comparison indicates that simple and faster 2D analysis has almost the identical results to 3D analysis which is complicated and time consuming.

Jan 1, 2008

By M. England

Keywords: Bi-directional tests, Osterberg cell, O-cell®, static load tests, Timeset® Static load testing, where loads are applied vertically to the top of the pile and often referred to as 'top down testing', has been used for many years and has become a 'standard' test for the world of foundation engineering. The method, although well developed, cannot be used under certain circumstances, magnitude of load being a particular issue. There is a finite limit to the load capacity that can be applied with either kentledge, the use of reaction piles or anchors, and as the loads increase, the costs escalate dramatically. A novel test method seeks to overcome all the associated problems of large scale and restrictive area "top down testing", utilising static load testing techniques. The method requires the foundation element to be divided into two or more sections and these can be loaded axially as required using a portion of the foundation element as a reaction. This paper presents some recent applications and developments in the use and application of the bi-directional testing technique using the Osterberg Cell or O-cell® and outlines some of the many advantages of the system. Recent bi-directional test loads applied to bored piles have mobilised capacities of 279 MN and with flight auger piles up to 25 MN.

Jan 1, 2006