Search Documents

By Alexander Scheuermann, Martin D. Larisch, David J. Williams

"Drilled displacement piles (DDP) have been used around the world for decades as foundation elements for structures and embankments. Typically the pile toes are designed to penetrate into stiff or dense soil formations to achieve sufficient base resistance. Recent research at The University of Queensland in Brisbane, Australia has discovered that the in situ stress conditions in stiff to hard clays is directly related to pile installation rates, which in turn are a function of the piling rig capacity and ground conditions. With adequate and constant pile penetration rates in situ stress conditions in the stiff to hard clay are increased by about 40%, resulting in significantly higher pile capacities. If pile penetration rates are too slow the in situ stress conditions are reduced considerably by remoulding and shearing of the clay, potentially causing reduced pile capacities. The paper presents the results of full-scale test piles at a stiff to hard clay site installed using different full-scale piling equipment.INTRODUCTIONDrilled displacement piling (DDP) is a piling technique in which a hollow stem, fitted with a purpose built displacement tool at the bottom, is drilled into the ground. Dissimilar to non-displacement piles, like Continuous Flight Auger (CFA) piles or conventional rotary bored piles drilled with kelly bars, the soil is not excavated during the DDP penetration process, but is displaced laterally and to a lesser extent vertically. The cavity created by the drilling tool is filled with highly workable concrete during the extraction process. The DDP technique is very economical providing high production rates and creating only marginal drill spoil, which has led to its increased global usage during the last decade. The typical DDP installation process is described in Figure 1."

Jan 1, 1900

By Franz-Werner Gerressen

As alternative energy industries pick up speed internationally, and as government regulation and restriction limit the use of impact hammers due to environmental limitation from construction induced noise during pile driving operations, unconventional solutions for more complex offshore foundation installations have become a necessity. Manufacturers and equipment suppliers race to develop alternative techniques to accommodate for offshore foundation construction in various soil conditions and at greater water depth. The FLYDRILL, and the Seabed-Drill BSD are two innovative systems for the installation of offshore monopiles with reduced environmental impact

By Leonhard Weixler, Jean Wehbe, Gordian Ulrich, Franz-Werner Gerressen

"As alternative energy industries pick up speed internationally, and as government regulation and restriction limit the use of impact hammers due to environmental limitation from construction induced noise during pile driving operations, unconventional solutions for more complex offshore foundation installations have become a necessity. Manufacturers and equipment suppliers race to develop alternative techniques to accommodate for offshore foundation construction in various soil conditions and at greater water depth. The FLYDRILL, and the Seabed-Drill BSD are two innovative systems for the installation of offshore monopiles with reduced environmental impact.INTRODUCTIONThe FLYDRILL and the Seabed-Drill were born from techniques in the design and construction experiences gained from land based foundation drilling systems over the past 25 years. As the alternative energy industry ventures into uncharted territory of deeper water for offshore wind farms, fast current regions for tidal energy, and increasingly challenging soil conditions and project complexity, the advancement and development of new innovative equipment system and drilling techniques have become a necessity.The systems described herein show the development of the so called “FLY-Drill” system, and the all new “Seabed-Drilling” equipment applied at the first ever made job using a seabed drilling rig.FLY DRILLThe FLY DRILL method is a completely new concept for bored piling. The drilling unit with rotary head, Kelly bar, and drilling tool is suspended by the hoist rope of the base carrier crane. The hydraulic power for the drill unit is provided from the base crane.The drill head is fixed on the casing with a hydraulically operated clamping system during the drilling operation. When emptying the drilling tool, the clamp cylinders are opened and the complete unit is swung sideways."

Jan 1, 2017

By Brian Koch

Michels installed 242 drilled shafts to support the piers for a new basket-handle, true-arch twin bridge across the Mississippi River from Moline, IL to Bettendorf, IA. The installation of the drilled shafts was completed with the simultaneous use of two Liebherr LB36 and one IMT 300 drill rigs. Utilizing barges, 233 drilled shafts were installed in the river. Michels crews also installed 7-ft to 10-ft permanent steel casing into the bedrock, and drilled to depths of 60 feet for each shaft. Despite working in strong currents, freezing temperatures and on rocking barges, Michels crews placed the shafts within 3 inches of plan position. Since the drilled shafts are the key piece in supporting the bridge structure, Michels provided cross-hole sonic logging to verify the integrity and strength of the concrete within the shafts and to add another level of quality control for the owner/customer. Extensive planning took place each day to ensure that tugboats, the linchpin of the project, were being efficiently utilized to shift the barges and materials daily. On any given day, Michels transported five concrete trucks by barge from shore to shaft sites to pour between 40 and 240 cubic yards of concrete. The Michels environmental team was diligent with preparing, discussing and implementing a water treatment plan that was accepted by all state and federal agencies and adhered to strict environmental regulations. Grain hopper barges were rented to control and treat the water that was used in the drilling operations. Another challenge crews ran into was the discovery of caverns when drilling into some parts of the bedrock. Michels worked with the engineer to develop a plan to construct the drilled shafts that encountered the caverns.

Jan 1, 2019

By Richard Hanke, Franz-Werner Gerressen

"The twin decked Alaskan Way Viaduct is a passage to Seattle’s downtown waterfront and of great economic importance to the city. In 2001, the Nisqually earthquake damaged the viaduct and led to the redevelopment of this corridor. The project includes two miles of 57.5 ft diameter bored tunnel beneath downtown Seattle and a stretch of new highway and overpass bridges at the southern tunnel entrance. State-of-the-Art special foundation equipment was mobilized for the project to perform a broad range of geotechnical construction. Applications included soil mixing and jet grouting for confinement cells around new bridge foundations, large diameter secant pile walls for the Tunnel Boring Machine launch portal along with an extensive jet grouting regime for ground improvements within the tunnel alignment. This paper will study the evolution and use of advanced special geotechnical construction equipment and describe its application at the Alaskan Way Viaduct Replacement Project.INTRODUCTIONThe evolution of geotechnical construction equipment continues through innovative applications and continued modification or enhancement of machinery. Similarly and in parallel, market expectations continually demand more in terms of construction speed and performance. Together, market demands and contractor innovation have led way to the development of specialty geotechnical construction equipment with capabilities previously not seen feasible or possible. Several examples of this scenario have recently developed during design and construction of the Alaskan Way Viaduct Replacement Project.The Alaskan Way Viaduct Replacement Project is a joint project between the Federal Highway Administration (FHWA), the Washington State Department of Transportation (WSDOT), and the City of Seattle. Three build alternatives were under consideration for replacing the Alaskan Way Viaduct: the Bored Tunnel Alternative, the Cut-and-Cover Tunnel Alternative, and the Elevated Structure Alternative. Ultimately, the bored tunnel option was selected as the best value approach. The project includes two miles of 57.5 ft diameter bored tunnel beneath downtown Seattle and a stretch of new highway and overpass bridges at the southern tunnel entrance. Several other associated improvements tie into this project that will ultimately lead to the complete demolition of the viaduct and redevelopment of Seattle’s waterfront."

Jan 1, 2015

This paper summarizes seven years of Italian ex­perience with the use of large calibration chambers for the calibration, under closely controlled stress and strain conditions, of some in situ testing devices which are used in sand deposits. At the present time two calibration chambers are operating in Italy, one at E.N.E.L.-C.R.I.S. (Milan) (*) and the other at I.S.M.E.S. (Berga­mo) (**). Both chambers can accomodate cylindrical samples 1.2 m in diameter and 1.5 m in height. A detailed description of these chambers can be found in Bellotti, et. al (1982).

Jan 1, 1987

By Florian König

It is well known that the bearing capacity and stiffness of displacement piles may increase significantly with time, a phenomenon usually referred to as set-up. In cohesive soils the set-up is commonly explained by consolidation processes in which the dissipation of the excess pore pressures around the pile leads to an increase in effective radial stresses. Recent case histories show that set-up may also occur in sand over a period which exceeds by far the consolidation process. Therefore, other effects apart from the dissipation of excess pore pressures must contribute to this long-term set-up effect. This paper presents the results of a series of multiple pile load tests on prefabricated concrete piles which capture the effect of pile set-up empirically. The main characteristics of the set-up trend are shown with respect to soil type, pile dimensions and distribution over the pile length. Possible reasons for pile set-up like consolidation and stress relaxation after the end of driving are examined using a finite element model which simulates the pile installation process.

Jan 1, 2006

By Rajesh A. Vaidya

A large scale piling work is undertaken in India for an important fast track industrial project. Thousands of solid square precast concrete piles are driven to depths of around 50m. Soils encountered are of alluvial origin with very soft clays varying in thickness from 10 to 18m at the top followed by medium dense to dense and occasionally very dense sand, stiff clay and finally dense to very dense sand layer as the founding layer. Recent site grading with around 4 metres thick hydraulically filled river sand necessitated driving the piles to the bottom sand layer to avoid problems on account of negative skin friction and to achieve optimum pile capacity. A process approach suggested by Bell et al (2002) to promote better understanding of the pile behaviour, pile capacity, and parameters assumed at design stage for static capacity and for wave equation analysis is followed with an aim to bring in effective economy in terms of pile length and pile installation speed. Soil investigation work is also undertaken in stages to cut down pile wastage. A judicious combination of PDA and static pile load tests is followed. Pile Driving Analyser (PDA) tests at end of driving and also at various stages of recovery of pile capacity are carried out to understand the pore pressure dissipation phenomenon. The paper attempts to present some of the valuable experiences that would go to establish precast pile as a very effective alternative to driven cast-in-situ piles and bored piles which are very common in this part of the world despite their limitations in terms of economy, speed and certain geotechnical aspects.

Jan 1, 2007

By Saba Mohan

This study presents results based on the Pile Installation Demonstration Project (PIDP) that was conducted as a part of the East Span San Francisco-Oakland Bay Bridge Seismic Safety Project. For the three full-scale pile installations, two different high-energy hydraulic hammers were selected for the installation. However, these hammers may not have sufficient energy to drive these large diameter piles at their ultimate capacity following long-term set-up. Nevertheless, these hammers were selected because, soil plug behavior, the generation of excess pore pressures and remolding of soil during driving were expected to reduce the shaft and end bearing resistance, and therefore reduce the energy required to drive these piles to design penetration. Data collected during continuous installation driving and after a series of re-strikes at different set-up times ranging from 1 to 33 days were used as input data for CAPWAP. These results were used to estimate the soil resistance along the pile length and at the toe of the pile, and the soil pile set-up behavior. Validity of the procedures used to predict the soil resistance to driving and predicted blow counts were verified with the field observed blow counts and the energy that was delivered to the pile. Based on combined CAPWAP analyses, the soil pile set-up with time was estimated and compared with results of other methods currently available in the literature for predicting the soil pile set-up rate.

Jan 1, 2002

By Andrew Baxter

The Crystal Bridges Museum of American Art in Bentonville, Arkansas is a beautiful glass and concrete structure cut into a valley that mingles with water ponds spanned by multiple bridges with suspended roofs. Or, at least it will be when completed in 2009. At Crystal Bridges, most of the proposed buildings involve cuts up to 50 ft high to be retained by the building structures. This requires the construction of retaining walls adequately founded to support lateral loads of up to 70 kip/ft. To add to this difficulty, the site is within a karst region with all the variability and irregularities associated with solutioning and erosion of the parent rock in this environment. The irregular rock profile made it virtually impossible to conceive a predictable arrangement of shallow footings and shear keys for the retaining walls. The existence of layers of soft soils within a hard rock formation made a caisson foundation impractical. The authors developed an innovative solution based on micropiles, which proved to be invaluable from a cost and schedule point of view. In areas where rock was shallow, micropiles were used as ?shear pins? to transfer the horizontal loads to the rock. In areas with significant overburden, a system of vertical and battered micropiles was devised to carry vertical and horizontal loads from the retaining walls. This paper presents a detailed description of the design and installation of the micropiles used as shear pins, and includes the results of lateral load tests performed on full-scale models of the grade beams on shear pins. The work performed shows that micropiles in rock can be effectively utilized for support of significant lateral loads provided that an adequate arrangement of suitably sized micropiles is provided, and that micropiles used as shear pins may develop significant tensile stresses when loaded laterally.

Jan 1, 2008

By Tracy Brettmann, Shailendra Endley, Jason Leary, Shashank Valluru

"Augered Cast-in-Place (ACIP) piles have long been used for deep foundation support in sands due to their high capacity and speed of installation. Very little information exists on the effects on capacity if the auger needs to be withdrawn from the hole prior to grouting. This condition can occur due to various reasons including grout plug ups, equipment issues, and grout supply delivery problems. It can become a major problem for the project team if this happens during production because the capacity of that pile is then in question, potentially resulting in re-design, installation of replacement piles and/or schedule delays. This paper compares the results of two high capacity test piles installed into a dense sand where one test pile was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth and the other test pile was installed utilizing conventional industry standard methods. Identical load tests were then performed on both piles to compare the effects of the two different installation procedures. The load test results were surprisingly similar in this case although the grout take required for the test pile installed in the pre-drilled hole was significantly higher to produce a similar grout return depth.IntroductionAugered Cast-in-Place (ACIP) piles are used extensively along the Texas Gulf Coast due to their combination of high capacity and speed of installation resulting in one of the most cost effective deep foundation systems relative to other options. Soil conditions in this region typically consist of alternating layers of sand and clay in the upper several hundred feet. ACIP piles are routinely installed to depths of over 100-ft to achieve the required capacity depending on the site specific soil conditions and therefore typically extend through and tip into sand layers. Occasionally, due to various reasons like equipment issues and plug-ups, the auger is withdrawn from the hole without grouting. Significant sand in the soil profile could lead to questions about the effect of the auger withdrawal on the pile capacity and load deflection relationship.This paper summarizes the results of two identical pile load tests performed on adjacent piles of the same length with the main difference being one was installed using the standard installation procedure and the other was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth. The load test results were then evaluated using load transfer analyses to estimate the effect of the withdrawal of the auger on the load-deflection characteristics and capacity."

Jan 1, 2017

By Grischa Dette, Thomas Schröder, Holger Merski

For the construction of the tunnel for the new Berlin S21 light rail line, a construction pit had to be built below the crossing B 96 federal road. For this purpose, the construction pit M’ has been built beforehand as a preliminary structure for the later S21 Berlin. A crucial element of this structure is a 2.50 m deep reinforced concrete deck slab which carries the B 96. During the later construction of the S21, it became clear that the existing preliminary structure could not be used without major modifications. Consequently, the construction pit design was gradually upgraded – still with the aim of retaining the basic concept of a trough structure with a jet-grouting cut-off. As construction progressed, for reasons of stability it became necessary to develop a fundamentally new concept with an underwater concrete base replacing the jet-grouting cutoff. This paper describes the planning and construction of a cut-and-cover structure with an underwater concrete base – a layout that brings with it the difficult task of underwater excavation and concrete placing without direct accessibility from above. Special emphasis is placed on describing the innovative approaches in connection with a remotely controlled underwater dredger from the Norwegian offshore industry for excavation works. Furthermore, the sophisticated underwater technologies for concrete placing in the confined surroundings are described.

May 1, 2022

By Martin B. Hudson, Andrew K. Cho, Rolff B. Knobel, Les R. Chernauskas, Jonathan L. Ernst

ABSTRACT The Bruce Museum, located in Greenwich, Connecticut, is home to an extensive display of art and natural history exhibitions. A large addition was designed to be constructed adjacent to the museum requiring new spread footings to be installed up to 16.5 feet below the existing foundations. The soil conditions at the site consist of highly variable sand and gravel overlying weathered rock and sound bedrock. The Contract Documents called for traditional foundation underpinning. Traditional underpinning techniques, however, presented two major challenges on this Project; (1) deep underpinning pits would be required involving multiple levels and staging with tieback support and (2) the highly variable soil and bedrock composition and elevations presented uncertainty in the design and construction of the pits. In lieu of traditional underpinning, Geosciences Testing and Research, Inc. (GTR) proposed an “active” soil nail underpinning system. A major reason that the soil nail underpinning option was feasible, related to the fact that the soil nails and facing could be installed slightly in front of the existing footings rather than directly underneath the existing footings. The soil nail wall design involved one to four rows of soil nails with nail positions and wall depth able to be adjusted “on the fly” as excavation progressed depending on the field conditions encountered. To create the “active system,” the soil nails were pre-loaded to mitigate wall deformations that would be associated with a standard passive soil nail wall design. To evaluate the performance of the active soil nail wall and confirm design assumptions, an extensive automated monitoring, on-site testing and inspection program was proposed and executed by GTR to monitor deformations of the wall and the museum in real-time, evaluate and confirm bedrock and soil bond stresses and ensure that each soil nail was pre-loaded and locked off. Careful analysis, planning, and use of the observational method illustrates the importance of collaboration between design and construction personnel and applying engineering judgement throughout construction. The use of the observational method includes the potential for modifying design based on conditions observed. This paper presents a unique case study of the “active” soil nail underpinning system to support and protect sensitive structures, close collaboration between design and construction facilitated by real-time deformation monitoring, and its successful application as a safe and cost-effective alternative to traditional underpinning.

Oct 1, 2022

By Richard E. Sylwester

Evaluating surface and subsurface conditions for marine foundations (bridges, causeways, terminals, etc.) is often done with a limited amount of data. Subsurface information for these projects is primarily acquired using traditional methods, such as boreholes, test pits or divers, which tend to be expensive and limited in the area of coverage. A number of geophysical methods, including precision bathymetry, sidescan sonar, and seismic reflection or subbottom profiling are extremely cost-effective and obtain significantly more data than can be acquired using traditional intrusive methods. These geophysical methods provide detailed surface images and continuous profiles of the subsurface stratigraphy. This information can be invaluable for selecting the best location for geotechnical boreholes and to map potential geohazards such as submarine slides and filled or open scour holes. Offshore investigations conducted for a proposed highway bridge (Knik Arm Bridge, Cook Inlet, AK), the retrofit of two existing bridge (Antioch and Dumbarton Bridges, CA) and a proposed cruise ship terminal (Ketchikan, AK) used a combination of geophysical methods to map water depth, detect and map debris on the seabed, map the thickness of unconsolidated sediment, determine the depth to bedrock and identify potential geohazards such as scour holes. The results of the geophysical investigations will be used to select locations for obtaining geotechnical borings, to extrapolate geologic information between existing or proposed boreholes, evaluate the potential depth of scour and design a pile support pier. Geotechnical engineers, offshore contractors and bridge designers are realizing the importance of the early use of offshore geophysics for (i) site characterization, (ii) to reduce the uncertainty of geotechnical conditions thus avoiding designs that may be overly conservative and thus more expensive and (iii) to assist in selecting locations for geotechnical borings.

May 11, 2007

By Abid Adekunte

"Whilst safety is considered to be of high priority in every aspect of engineering projects, it is equally important for designers and contractors to be continually aware of their obligations to the immediate environment and the society as a whole. These include responsibilities to minimise the amount of nonrenewable natural resources and energy used on projects, to reduce carbon foot prints on projects, to minimise the quantity of wastes produced on projects, to minimise the level of pollution on construction sites and to reuse materials and waste products whenever and wherever possible.In other words, professional engineering practice needs to be accompanied by an underlying fundamental objective to improve, restore and sustain the environment. However, achieving this objective requires continuous collaborative interaction and effective communication between the different specialists involved on every project from the early stages. In addition, developing a well-thought-out economical solution is key to achieving the sustainability aspect of the above objective.This paper focuses on the design, construction and management of a recently completed large multi-level basement scheme in Central London, with greater emphasis on collaborative approaches taken by the design engineers, commercial managers, construction managers and site operatives to deliver the most reasonably economical and sustainable solutions to the client. Solutions were based on combinations of general and specialist engineering knowledge, with due considerations for health & safety, sustainability, cost, practicality, time and community requirements.INTRODUCTIONUnderground structures have become vital components of urban life worldwide e.g. tunnels serve many water, wastewater, highway and railway schemes, basements have been incorporated into many urban commercial, institutional and residential developments, while many public underground car parks have been built to deal with the incessant problem of insufficient surface parking spaces in busy urban centres.The safe design, construction and maintenance of underground structures have been well-mastered by the deep foundation industry over the years. However, just like many other areas of engineering, aside the need to satisfy safety requirements, underground construction practice is now faced with a new set of requirements; the demand for more sustainable and cost-effective solutions, with reduced environmental and societal impacts. Designers and managers of underground construction schemes are now compelled to minimise the use of natural resources and energy, to minimise the amount of waste produced, to minimise the level of environmental pollution, noise and disruption to traffic and normal societal life at ground level around underground construction sites. In addition, the recycling of site wastes and reuse of materials have now become important aspects of underground space development. Considerable effort is being put into promoting sustainable development across the industry."

Jan 1, 2017

With respect to liability damages, claims and costs thereof relating to or ansmg out of contamination, special or non-special wastes, hazardous wastes or pollution in connection with the performance of this subcontract: It is understood that the subcontractor's work and responsibility wholly exclude any requirement to handle such contaminants or to otherwise be responsible for such contaminants, and Subcontractor shall not be nor be considered to be a generator of such contaminants. Contractor shall indemnify, defend and save harmless Subcontractor and its sureties, from and against all liability, damages, claims and costs relating to or arising out of contamination, special or non-special wastes, hazardous wastes

By Jacob A. Jordan, Rachel M. Garrett, W. Robert Thompson III, James C. Pegues

"Environmental control structures for an existing fossil-fuel power generating plant near Pascagoula, Mississippi faced several design and construction challenges due to space limitations. Conceptual design calculations indicated drilled shaft foundations would likely be needed to accommodate the higher lateral and compressive loads expected under some structures. A maximum drilled shaft diameter of 60-in was preferred due to various space constraints. Smaller diameter drilled shafts were deemed acceptable under structures with more moderate loading conditions. Furthermore, augercast piles were considered where lateral loading was not a governing design criterion.A series of SPT borings and CPT soundings revealed a subsurface profile consisting of soft to firm clays to depths of about 25 feet, underlain by fine to coarse sands. The apparent relative density of the sands was loose just below the clay, with increasing density noted with an increase in depth.Analysis of conventional drilled shafts indicated needed capacities could not be achieved unless shaft lengths exceeded 100 feet. Post-grouted drilled shafts were therefore evaluated to decrease shaft lengths by taking advantage of increased base capacity. Analyses showed the higher predicted capacities needed for some structures could be achieved with this approach. Final design for the project incorporated 90-ft long, 60-in diameter post-grouted drilled shafts; 60-ft long, 48-in diameter post-grouted drilled shafts; and 60-ft long, 48-in diameter conventional shafts. Both post-grouted and conventional trial shafts were installed as part of the detailed design phase of the project. Each trial shaft included CSL integrity testing and Osterberg-cell bi-directional load testing. Load test results revealed that additional base capacity was, in fact, achieved through the post grouting process. The 60-in diameter post-grouted production shafts and the 48-in diameter conventional production shafts have been installed at the site, with the project that would utilize the 48-in diameter post-grouted shafts deferred at this time."

Jan 1, 2015

By Dr. Anup Kumar Mandal, Partha Roy, Shuvranshu Kumar Rout, Dipak Mandal, Biswajit Das

Installation of a new scalping station with bunker, apron feeder, scalping screen, ramp -retaining wall and approach bridge was planned in an existing integrated complex of phosphate fertilizer at a remote place in West Africa. Rock phosphate ROM, transported from mines by a combination of 100 Ton and 150 Ton dumper, would be fed to a steel bunker having capacity of 180 m3. Different options were studied for retaining wall at the junction of ramp and approach bridge. Initially options with conventional RCC Retaining Wall, Gravity Retaining Wall with Precast Concrete Blocks and Reinforced Earth walls were studied. Option with Reinforced Earth was selected as this option was much more cost effective compared to other options. But real engineering challenges cropped up when competent execution contractors were not available nearby the site. To minimize the cost, an innovative option with Stepped Retaining wall was then studied. Geotechnical parameters of native soils, selected for the construction of the approach ramp were determined and it was found that with available poor geotechnical parameters of the native soils, design of stepped retaining wall would not be feasible with respect to available bearing capacity, subjected dead load, live load, operational load and earth pressure. A conscious effort was then made to make the design feasible by improving the geotechnical parameters of the retained earth of ramp near the retaining wall. In view of that, mix design with locally available materials like Silexite, Sand, Laterite, Gravel and Silt at different proportions was made and samples were tested in the laboratory to determine relevant geotechnical parameters. Based on the test results, a suitable mix was selected that had high shear strength, enhanced bearing capacity and improved coefficient of earth pressures. Design of stepped retaining wall was then made with the selected construction materials and construction completed. The plant was successfully commissioned in December. 2021.

Sep 1, 2022

By John R. Grillo, Gordian Ulrich, Franz-Werner Gerressen

Most geotechnical construction professionals are aware of piling using hydraulic drill rigs and the so-called Kelly drill mode. Kelly drilling has many advantages as it can work with a wide range of tools facing almost all types of soil and rock conditions. Kelly drilling can also deal with diameters up to 10 ft (3.00 m) and bigger or depths of more than 330 ft (100 m). Nonetheless, there is a concern about Kelly drilling as it is a relatively slow installation process. Therefore, an alternative piling method like Cased CFA (CCFA) Piles (Cased Auger Cast Piles) provides a significant advantage in terms of installation performance, schedule and cost saving potentials. Major application for the Cased CFA system is the secant pile wall construction. Against the traditional secant pile wall systems like fully cased bored piles or CFA secant piling the Cased CFA secant pile wall system has the advantage in cost and time against the fully cased system and in quality against the standard CFA system. This paper will describe the methodology and installation process in general as well as first reference projects carried out in the United States. This paper will present the results in cost and schedule saving using this method. In addition, we will also describe the limitations of this method. INTRODUCTION In the changing construction environment, companies are searching for new technologies or improvement of existing technologies to complete their projects in shorter time frames to provide a good economic solution. Especially with the focus of increasing urbanization, the aim of fast construction becomes more and more important. When thinking of piling, most people will have the same picture in mind: that of a hydraulic drill rig working in Kelly drilling mode; however, the perpetual drill rig development provides a number of options for the execution of specialist foundation projects, either for foundations or for pile walls when using single pass applications like CFA, Cased CFA and Full Displacement Piling (FDP). Single pass means, in general, that the tool is pushed and rotated into the ground to the final depth in one stroke. After reaching the final depth, concreting is started and concrete is pumped continuously while the tool is withdrawn.

Jan 1, 2019

By M. Nomura

This paper describes the results and field measurements of two long-term observation tests and two short-term loading tests to confirm the effectiveness of NF piles in reducing negative skin friction. All the test piles were equipped with strain gauges, allowing measurement of the compressive axial forces in the piles. These test results prove that NF piles are effective in reducing the negative skin friction to an insignificant value. Some examples of the design procedures used in Hong Kong and Japan are also presented.

Jan 1, 2010