Search Documents

By Ruy L. Rodrigues

Vale is in the early stages of commissioning its Onça Puma nickel operations. The project is meant for the production of 58,000 tpa of nickel contained in ferro-nickel, substantially contributing to the company?s vision to achieve world leadership in the nickel business. Mineral resources will be exploited from the homonymous deposits in the Midwest of state of Para, Brazil ? some 100 km southwestwards from the company?s Carajás iron ore properties. Resources as of 83 Mt at 1.73 % Ni will sustain a mine life of approximately 40 years. The property was acquired in late 2005 and Vale has since extended the engineering studies and proceeded with the implementation. Nickel will be mined from saprolitic ore at a rate of approximately 10 Mtpa (ore plus waste) in early years ? ramping up to some 15 Mtpa 7 years later ?, to feed the plant at a rate of 2.5 Mtpa. The process uses conventional RKEF (Rotary Kiln Electric Furnace) pyrometalurgical route whereby the ore is homogenized, calcined in rotary kilns, melted in electric furnaces and further refined to ferro-nickel. The plant has been designed and constructed applying the latest available technology, aligned with Vale?s vison to exceed the highest existing standards for environmental control, health and safety and productivity in the industry. Total investments in these operations are anticipated to correspond to USD 2.3 Bi and will materially contribute to the regional development and well being of the nearby communities and other stakeholders.

May 1, 2010

"Polycom, a new approach to ore processing based on pressure comminution, is obviously a very attractive alternative to conventional processing methods.Since a full-scale pilot plant was commissioned in 1986, more than 125 commercial installations, with capacities up to 1000 t/hr, have gone ahead.Already successfully used in processing cement clinker, limestone, coal, and other minerals, Polycom high pressure grinding results in:o Significantly reduced capital costs, because smaller units can be used m new installations;o Capacity increases of up to 100% in existing facilities; and o Operating economies that include energy savings of 20% or more, and reduced wear parts consumption.1. IntroductionAutogenous or semi-autogenous mills in conjunction with rod or ball mills are used with preference for ore processing. Most ball mills are of closed-circuit design and operate with mechanical classifiers (spiral or rake classifiers) or hydrocyclones. In other words, the ores undergo wet primary grinding, since slurries are required for the downstream separation stages anyway. This paper presents a new grinding system based on high pressure comminution of ores. This grinding process allows:- Energy savings of up to 20 % or more- Capacity increases of up to 100 % and more- Reduction of wear costs- Smaller units for new installation and thus- Reduced investment costsThese advantages are highly interesting for both new installations and conversion projects, particulary in cases where an increasing hardeness of the ore, i.e. rising Bond Work Index, reduces the output of the plants or where the metal assay of the ore decreases and the capacity of the existing systems has to be increased. POLYCOM high-pressure grinding rolls have established themselves with great success already for grinding cement clinker, granulated blast furnace slag, limestone, cement raw materials, coal and other materials.Meanwhile more than 250 high pressure grinding rolls have been installed worldwide. Capacities up to 1.000 t/h with roller diameter up to 2.8 m and drive units up to 2.400 kW are installed."

Jan 1, 1991

By K. Lim, J. Sobil, L. Galarza Castillo, F. Tozlu

"For mining operations globally, the scale and criticality of the grinding mill drive has meant that selection of the correct mill drive technology is paramount. With so much depending on the successful implementation of the electrical drive system— safety operation, timely installation, availability, energy efficiency, minimum maintenance and extend its use as tool to assist during mill liner exchange—customers are justified in their scrutiny and slow adoption of new drive technology. From the first installation of low, fixed speed synchronous motors to the introduction of the current source and further voltage source variable frequency drive, innovations require long periods of time and mining customers willing to push the industry forward. In recent years, the variable frequency drive has been the stepping stone for a new generation of mill drive technology. In use for decades in other heavy industrial applications, the drives allow for system optimization in a myriad of ways. The most dramatic of changes is in the design of the motor. Where in the past motor design was bound by line frequency, today the designer can optimize machine size and, more importantly, eliminate the need entirely for the synchronous motor. Induction motor design has now progressed to the point where low speed operation is possible at efficiency levels nearing those of the synchronous design. Moreover, the simplicity of the squirrel cage design means that availability, reliability and spare part requirements are greatly improved. As the next step in the evolution of large pinion driven grinding mills, the low speed induction drive offers a new reliable and robust system to the market.IntroductionAs deposit grades continue to decline, new ways of processing ever greater concentrator throughputs have been required to maintain throughput efficient and profitable operations. Furthermore, the high risk nature of mining developments requires a constant search for safer, higher availability and more efficient equipment design. Limitation of downtime is a key factor in ensuring mining operations can be sustained through volatile market conditions. Often processing the entire mine throughput through just 1 or 2 lines, the crushing and grinding circuits are of particular criticality to the uptime and, thus, profitability of any mining operation."

Jan 1, 2016

By B. St. Pierre

"The alchemists' symbol for antimony is a diamond with a dot in the centre. The latin name ''stibium'' gives this mineral its chemical symbol ""Sb"" and the name to the principal ore containing antimony. This is Stibnite, a sulphide of antimony, and the valuable mineral at the Consolidated Durham operations. Stibnite chemically pure contains 71.69% antimony metal.Antimony is used in many forms, as an alloy in the production of metal products and as chemical compounds of oxides and sulphides. In Biblical times, antimony was used as a medicine and as eyebrow makeup.Today, the largest single use of the metal is as a hardener and strengthener of lead, and corrosion inhibitor in storage batteries. New applications for antimony in its oxide form as fire retardants are broadening the overall demand especially in the chemical, plastic and fabric industries. Other users include the Military for such things as tracer bullets, shrapnel, smoke screens and flame throwers. An unusual property of the metal is that it contracts when heated which has made it a valuable alloying metal in the printing industry, for heat shields on re-entry vehicles used in the space programmes, and also for the manufacture of bearings."

Jan 1, 1977

By Stephanie Price

Engineering Associations ?Regulatory authority ?License individuals and firms ?Discipline licensed members ?Enforce against improper acts ?Programs for EIT?s, competence, etc

Oct 1, 2010

By H. A. Bilgin, G. G. U. Aldas

"Ground vibration is the natural result of the blasting process. Many empirical formulae and methodologies including analysis of travel path effects have been developed. The scaled distance, which is the most popular approach for the calculation of the attenuation of particle velocity in the ground, has led to significant advances in the prediction of particle velocity when both explosive charge and distance vary. However, this approach does not consider the effect of ground anisotropy and existence of structural geological features on ground vibration. Therefore, in this study, the effects of these rock mass properties on types, amplitudes, and frequencies of ground vibration waves at four surface mines are examined. The results, which were implemented at Kangal coal mine, Bastas quarry and Kíbrís quarry, provided guidance for the extensive study at Orhaneli surface coal mine.As a result of the study, the authors came to the conclusion that vibration amplitudes change depending on the ground on which sensors were deployed and the conditions depending on whether measurements were done near major structural geological features. It was determined that the vibration amplitudes, measured at equal distances from the source but in different directions, change because of the propagation velocity anisotropy. Besides the change of wave type due to the kind of ground at the measurement location, it was determined that vibration anomolies were due to structural features."

Jan 1, 2004

By Matthew A. Baumann

Tooth-wear on mining shovels requires continuous monitoring. Worn teeth impede excavation performance, increase energy usage, and increase the risk of lost or broken teeth and adapters. A machine-vision-based automated tooth-wear monitoring system is presented. The system employs a rugged boom or stick-mounted camera to capture images of the shovel teeth. An onboard computer processes the images in real-time to determine the length of each tooth. The current wear state is available via a network-accessible log for on-demand status updates. By continuously recording tooth length changes over time, the logs can be used to estimate wear rates and patterns, permitting comparisons between different G.E.T. configurations, operator behaviour patterns, or material types. This detailed, quantitative data permits site-specific optimizations to wear packages and maintenance scheduling. Automating wear monitoring offers the crucial wear information necessary to minimize maintenance costs and reduce unscheduled downtime. A 37-day field trial in a copper-gold mine demonstrated the ability of the system to measure tooth lengths, compute wear rates, and detect differences in tooth wear based on their position on the bucket.

Nov 1, 2011

By Pierre Pelletier, Julie Fournier, Gianni Bartolacci, Yves Breau, Dominique Girard, Ahmed Bouajila, Carl Duchesne

"The development of on-stream analyzers (OSA), such as those based on X-ray fluorescence (XRF), has been key to improve metallurgical performance of flotation processes. However, since these analyzers are shared between several streams, they typically provide grade measurements every about 10-15 minutes. In general, this frequency is too long compared to process dynamics and so, implementing an efficient feedback control strategy based on OSA can be difficult. In addition, due to the limited capacity of OSA systems, several important intermediate streams are not analysed, but could provide relevant information about the state of a flotation circuit.To overcome this problem, vision systems have been developed in the past to predict concentrate grade based on froth color – this could be very useful to control flotation performance between OSA measurements. However, applications reported in the literature typically use univariate summary statistics of the full red, blue, and green color distribution of froth images, while RGB images are truly multivariate. Although, in some cases, grade prediction was achieved with reasonable accuracy, one may, by using only summary statistics, miss important information about the state of the flotation process.This paper investigates the application of Multivariate Image Analysis (MIA) concepts to flotation froth images. These techniques are based on multivariate statistical methods such as PCA and PLS, which have the ability to analyze large databases (such as digital images) and summarize the relevant information content of the data into a small number of latent variables, capturing the most important features of the images for concentrate grade prediction. The potential of application of these methods in the mineral processing industry is illustrated using a few industrial case studies."

Jan 1, 2003

By N. H. J. Freire, D. Majuste

In this paper, the effects of some organic compounds on the current efficiency, cell voltage and specific energy consumption during nickel electrowinning, and on the deposit features (morphology, crystallographic orientation and nanohardness) were described. The organics tested here (extractant, diluent, flocculant, lubricating oil and acid mist suppressant) are currently used in industrial plants. The results indicated that only the flocculant and acid mist suppressant exhibit relevant negative impacts on the current efficiency and energy consumption. The current efficiency dropped from 93.6 % (organic-free solutions) to 86.0 % and to 92.8% in electrolytes containing 100 mg.L-1 of acid mist suppressant and flocculant, respectively. At this concentration, their addition to the electrolyte led to increases of the specific energy consumption in the order of 18 % (acid mist supressant) and 2 % (flocculant). Cyclic voltammetry showed that Ni nucleation occurs at more negative potentials at 50 and 100 mg.L-1 of these organics in the electrolyte, thus indicating an inhibition of the deposition process. The deposit quality decreased at the higher concentration of all organics, when more hydrogen pitting was observed. The acid mist suppressant caused delamination of the Ni deposit at 50 and 100 mg.L-1. The addition of 100 mg.L-1 of flocculant and acid mist suppressant to the electrolyte increased the nanohardness of the deposit around 31 and 72%, respectively. The increase in Ni deposit hardness may lead to a decrease in the material ductility, thereby affecting the stripping and cutting of Ni sheets. Our findings may be helpful since strong adverse effect of some organics that may be present in the electrolyte were identified, thus the industry can control and optimize the organic´s dosage in the corresponding operations.

Jan 1, 2016

By Peter Cunningham

General Description of Projects The objective is to streamline data transfer within our Process Control and Business Systems for the purposes of tracking actual production, reducing manual record keeping, improving process control and improving vehicle maintenance. This presentation focuses on two implementations of mobile equipment data acquisition systems which make use of industry standard data models and data transport protocols. Pilots are part of the Mines Technology Roadmap to improve our mining operations ?Enabling technologies and pilot of key systems

May 1, 2013

The #3 Shaft at Brunswick Mine, Bathurst, New Brunswick, Canada, intersects a soft graphite zone just below the 3400 Level. Ground movement within this zone causes the concrete liner of the shaft to be deflected towards the shaft?s interior, affecting the steel framework of the conveyance. In some areas, the clearance between the cage and the liner has been reduced to less than 2 cm, which is a concern. An innovative surface-mounted extensometer was designed in 2008 to monitor potential movements of the shaft?s liner. Four such novel extensometers were installed in the shaft for the surveillance of a particularly critical 3.0m by 5.5m area. This article describes the approach taken to instrument the shaft, the principle of the new extensometer, as well as the performance of the instrumentation following its installation.

May 1, 2009

By M. W. Lewis

A mine's inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine ’s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

By M. W. Lewis, B. Sambirsky, J. Werner

A mine’s inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine’s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

By Simon W. Houlding

The mining community is geographically remote and widely dispersed. There is a growing requirement for formalized professional development of members by professional associations, and increasing recognition of the advantages of continuing education and training by both individuals and corporations. Working against these trends are the increasing expense and time commitments required for attendance at conventional courses and workshops. The result is a perceived need for a readily accessible source of continuing education and technical reference on the Internet. The design constraints for an Internet model for professional development include: ? browser compatibility, with any time, any place, any pace accessibility; ? a content presentation model with low bandwidth requirements, appropriate interactivity for examples, tools and reviews, and viewer performance monitoring capabilities; ? formal accreditation of content, presentation and process so that viewer achievements may be formalized in terms of widely recognized Continuing Education Units; ? availability of tools for conversion of source material to the presentation format with minimal effort. A model that meets the design constraints is presented and illustrated by examples from an existing Internet site for continuing education in mining.

May 1, 2002

By Ken Witherly

Modern airborne EM surveys typically acquire more data than is processed or analyzed at the time of acquisition Suitable additional processing can provide more diagnostic information, thereby allowing for more effective ranking and hopefully, follow-up of outcomes

Apr 1, 2005

By John Stubbs

Sub-Surface Shaft excavation Mine development Headframes Surface Production facilities Product storage and loading Tailings area Infrastructure Discovery Lodge Utilities Operations complex Port Marine loading Rail unloading and storage

May 1, 2013

By Norman O. Lotter, André R. Laplante

"The pursuit of concentrator surveying for purposes of metal accounting or process optimization has not yet connected with the well-published realm of geostatistics. The reality of lognormality in time has seldom been discussed. One publication by Krige, 1962, examined such effects for a gold concentrator in South Africa, towards an information system that would provide feedback to the mining and surveying teams on grade control of ore mined.During present studies which are designing and testing a new survey model, called statistical benchmark surveying, it was found that the distributions of feed, concentrate and tailings bear significant residual signs of the parent lognormality in space. The multiple hosting of paymetals in different mineral species complicates the understanding of these distributions. These features have to be recognized and treated in order to perform appropriate quality control on the diagnostic sampling performed in the pursuit of statistical benchmark surveying.It is shown in this paper that the above two features can actually be used to advantage in the diagnosis of continuous periods of operations data ahead of such surveying, including the estimation of recoverable paymetals in flotation tailings from a graphical method.INTRODUCTIONAssessment of Concentrator PerformanceMilling and flotation, sometimes accompanied by gravity separation, are well-established unit processes, which have traditionally been used to treat ore that has been mined. This is because these processes liberate, then separate, the valuable minerals, which contain paymetals, from host gangue. This is often done by a combination of crushing and grinding processes, or autogenous grinding, to liberate the paymetal minerals, followed by gravity separation and/or flotation, to separate these valuable minerals into a concentrate, or several concentrates. These concentrate(s) have a lower bulk than the parent ore from which they are derived. Further, they contain a high percentage of the valuable minerals. Accordingly, they are more economically treated in subsequent beneficiation processes than the ore from which they were produced."

Jan 1, 2005

By Yves Breau, François Robichaud, Jacques McMullen, Pierre Pelletie

"The Expert System implemented at the East-Malartic mill controls a copper flotation circuit while taking into account the profitability of the operation. Treating a copper gold ore, the flow sheet integrates a flotation step followed by cyanide leach circuit. The Expert System calculates the actual net smelter revenue of the flotation circuit, accounts for the operating cost of the cyanidation circuit and defines optimal metallurgical operating targets to optimize the overall economics. To be realistic, probability factors and circuit diagnostic analysis are integrated in the operating target selection. The Expert System has proved to be successful, robust and flexible. It resulted in a copper concentrate grade increase of 1% while maintaining recovery. The use of the expert system also gives plant personnel good training procedures and promotes interaction with mill operator.INTRODUCTIONThe East-Malartic mill is located close to the town of Malartic in North Western Quebec, Canada. The mill was first commissioned in 1938. The flowsheet at that time was a straight cyanidation circuit. The original mill operated in that mode up to the discovery of the Bousquet 2 orebody in 1989 which consisted of a massive copper sulphide ore averaging 0.7% copper and 7 g/mt of gold. Bousquet 2 ore processing required a mill retrofit. Grinding capacity, gravity and copper flotation circuits were inserted prior to the cyanidation circuit in order to achieve 3,200 mtpd capacity at expected recoveries.In 1993, control of the flotation circuit was deemed critical in order to maintain the flotation performance and to reduce cyanide consumption since the copper sulphide contained in the Bousquet 2 ore is a high cyanide consumer (50% bornite). (McMullen, 1999) As a result, the implementation of advanced control strategies in order to increase the metallurgical profitability of the plant and to reduce the operating variability between operators was the most rational alternative. In 1994, Corem was chosen to perform the plant audit and to write the first set of rules. The on-line control strategy was started up in 1995. In 1996 and 1997 the Expert System was shutdown because of an extreme change in the ore coming from the milling of Bousquet #1 ore and the departure of the projects engineer. In 1998, the system was restarted and the results were impressive. Furthermore in May of 2001 a patent was issued for the control strategy. (Breau, 2001)"

Jan 1, 2002

By A. Sheikh, S. Hardcastle

"Various methods of leaching are being used by Denison Mines Ltd. Uranium Operations. This study was designed to investigate the flood leaching operation of two parallel inter-connected stopes contained by pressure bulkheads. The teaching muck piles, created from large scale uppers production blasts, are aerated by compressed air lines laid beneath the pile prior to blasting.A SFr, tracer gas, injection technique has been employed to determine the post-blast integrity of the single-ended air distribution system. SF6 was injected into the compressed air line feed to the stopes and collected at borehole exhausts from the stopes in grab-sampling bags. Analyses of the air samples were performed with a gas chromatograph.The system was designed to give a sufficiency of oxygen to sustain bacterial activities used to enhance the leaching recovery in the muck piles. The results obtained indicated that there is a minor anomaly in the distribution system that may not be critical to the operation. Compared to an idealized case, the over-all efficiency of aeration throughout the muck is estimated at over 85%."

Jan 1, 1988

By Zhuo Chen, Jun Zhou, Jiemin Zhou

Samples of the reacting suspension particles were taken from the reaction shaft of a commercial flash furnace at different heights. The processes of matte and slag formation and morphology of the samples in the shaft were observed and analyzed. Variations of matte and slag composition in the shaft were investigated. By analyzing the samples taken from the settler at different locations, settler processes were studied such as slag formation, agglomeration and separation of matte-slag phases, Fe3O4 reduction, copper-in-slag reduction etc. In accordance with the characteristic of matte and slag formation the flash furnace can be divided into 6 functional regions, and a mechanism model called as “Micro bath process” is proposed for matte and slag formation in a commercial flash furnace. INTRODUCTION During flash smelting, concentrate particles scattered in the reaction shaft complete their oxidation reactions in suspension. The droplets produced fall into the settler beneath with a small amount of un-melted solid particles, agglomerate and separate into matte and slag layers which are tapped out from their tap holes separately. With respect to the extent of slagging reaction in the reaction shaft, there isn’t any commonly accepted understanding in literature (Kimura, Ojima, Mori & Ishii, 1986; Kemori & Kondo et al.,1988; Kemori, Denholm & Kurokawa, 1989; Fagerlund &Jalkanen, 2000). Some assume that the slagging reaction in the shaft can be ignored and some propose that all slag is produced in the shaft. With regards to the characteristics of the physical-chemical changes of concentrate particle in the reaction shaft, although there are some research results reported from pilot scale and commercial scale experiments (Kemori, Ojima & Kondo, 1988; Hagni, Vierrether & Sohn, 1988; Jorgensen, Taylor, Dickinson & Stevenson, 1992; Swinbourne, Simak & Yazawa, 2002; Kivinen & Tuominen, 2005), they are generally limited themselves to theoretical analysis and calculations. No studies are published concerned with the processes of matte and slag generation in the shaft, quantitative analysis of the processes, variations of matte and slag composition and morphologies of the melts along the axis of the shaft, etc.

Jan 1, 2019