Search Documents

By W. A. Alexander

Introduction In the course of a programme of research on beryllium in progress in these laboratories, knowledge of the recrystallization temperature became necessary. As the information is not available in the literature, the determination of this temperature for metallic beryllium was undertaken. By the reduction of grain size through working and recrystallization and the probable simultaneous induction of preferred orientation, it was hoped to improve the working properties of beryllium at lower temperatures. The recrystallization temperature is usually determined by observing the lowest temperature of annealing at which new crystals are formed in severely cold-worked metal or alloys. This temperature is profoundly influenced by the following factors: the purity of the metal, in the case of an element, or the composition of the alloy; the degree of straining or working; the temperature of straining; the original grain size; and the time held at the annealing temperature. The observed temperature is lowered by higher purity, more severe straining, lower temperature of working, smaller original grain size, and longer time of annealing. Beryllium presents special difficulties in that the percent elongation in tension is effectively zero, so that ordinary squeezing or rolling was not possible. A possible means of straining was suggested by the fact that indentation hardness tests could be made. It was known from earlier work that the metal could be worked at elevated temperatures, so that working at the lowest feasible temperature and quenching might also be a means of producing strain. The purity of the metal is also a point of some uncertainty in the case of beryllium. Losano has prepared 99.96% Be which appears to be the best reported. Distilled metal used in the present work approached this purity. However, by analogy with other metals, residual impurities may have a pronounced effect on the recrystallization. Further purification of beryllium would evidently entail considerable difficulties due to the highly reactive nature of the metal, and was not attempted.

Jan 1, 1947

By W. R. Middagh, R. M. Garvey

"Phosphate rock is shipped by boat from Florida to Vancouver, B.C., where it is unloaded and stored in a 50,000-ton silo. It is shipped from Vancouver in 100-ton hopper cars in 80-car trains to Fort Saskatchewan. Both the ship and the hopper cars are on a back-haul with potash. The rock cars are unloaded at Fort Saskatchewan at a rate of approximately 4 cars per hour. The rock is stored in three concrete silos, 40 ft in diameter by 110 ft high, which hold 18,000 tons of recoverable rock with 2,000 tons dead space. The rock is reclaimed from the silos by gravity and fed to the phosphoric acid plant by remotely operated conveying equipment.Problems encountered in the operation include scheduling the rock shipments, contamination of the rock with potash, and handling the 80-car trains both in Vancouver and Fort Saskatchewan."

Jan 1, 1968

"THE PACIFIC CONTINENTAL MARGIN OF CANADA is de-fined, for the purposes of this paper, as the area sea-ward from the present mainland coast of British Columbia to the foot of the continental slope. It thus coincides with A. Sutherland Brown's Insular Tectonic Belt. The region is limited to the north and south by the political boundary with the U.S.A., the location of which is still in dispute.The region can be subdivided into: (1) an interior trough comprising the Queen Char-lotte, Comox and Nanaimo basins; (2) a medial uplift comprising Vancouver Island and the Queen Charlotte Islands; and (3) a marginal shelf which is extremely narrow (Jess than 5 km) west of the Queen Charlotte Islands, widens to 160 km in Queen Charlotte Sound and is about 35 km wide west of Vancouver Island, where it is underlain by the Tofino sedimentary basin, with its• extension, the Juan de Fuca Basin, at the southern end.The medial uplift consists of a highly disturbed anticlinorium of mainly Mesozoic rocks, with a core of Palaeozoic. The rocks include thick sequences of eugeosynclinal volcanics and sediments. There is strati-graphical evidence of repeated interruption in sedi-mentation. By late Jurassic, the main eugeosynclinal phase was over and a successor basin was initiated in the interior' trough. This became filled, during Cre-taceous and Tertiary time, with sediments ranging in environment from bathyal turbidites to terrestrial conglomerates and coals. West of the medial uplift, another successor basin developed in early Tertiary times and became filled with mainly deep-water marine sediments. A third effusive sequence marks the base of the Tertiary on Graham Island and over most of the Hecate Strait region and Tofino Basin."

Jan 1, 1970

By Mark Rantapaa

Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the Autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the Open Pit and Process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput. Better fragmentation and a subsequent increase in mill throughput were achieved through the use of: 1) Electronic caps for more precision and flexibility, as well as for allowing extremely fast shots. 2) Explosives with a higher velocity of detonation (VOD), to provide for improved shock energy. 3) Improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by six tph in 2003 due to the improved fragmentation of the hard ore. Barrick Goldstrike?s D2M initiative includes roaster ?hard ore? (BWI >17), as well as autoclave ?hard ore? (BWI >15). Approximately six million tons of D2M material is expected be shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs.

May 1, 2003

By J. A. MacLellan

"CONSTRUCI'ION OF SHERRITT'S CONCENTRATORSSherritt Gordon is operating two mills north of the 56th parallel, and is presently engaged in building a third. The author was closely involved in the design and construction of all three of these concentrators.The Lynn mill is the oldest of these three concentrators-it is a 4,000 ton per day nickel-copper plant built in 1953. The Fox mill is a 3,000 ton per day copper-zinc concentrator built in 1970. The Ruttan mill will be a 10,000 ton per day copper-zinc plant scheduled to go on line in July 1973.LYNN MILL The Lynn mill including the crushing, concentrating, drying and load out plant is about 69,700 square feet or 17.4 square feet per ton per day. '!his plant was originally built in 1927 at Sherridon, 150 miles south of Lynn Lake, as a 2,000 ton per day copper-zinc plant. In 1952 the plant was moved by tractor train to Lynn Lake. The whole plant was re-oriented within the original perimeter walls as a 2,000 ton per day nickel-copper plant. This plant was expanded to 4,000 tons per day by the addition of t1-Jo rod mills and a 5-1/2 short head crusher in 1959.The Sherridon mill processed its last ore in Sherridon in September 1951 and the first load of nickel concentrate was loaded at Lynn Lake on November 9, 1953 when the railroad arrived at Lynn Lake.The site for the Lynn Lake mill was cleared of overburden in the summer of 1952 and foundations for structural steel and SO!l8 equipment foundations were poured the late summer and fall of 1952 • Steel was erected from January to June 1953. Most of the equipment came in from January to March of 1953 by tractor sleighs. Sane sleighs upset but no equipment was lest through the ice."

Jan 1, 1972

By Muhammad Usman Siddiqui

Managing and analysing the vast amounts of data collected in a mining project effectively is crucial for enhancing the project's economic feasibility. The efficient utilization of this data is critical to minimising the time spent on projects and increasing project value. Process engineers can effectively integrate geometallurgical data into plant operations by employing analytical tools like Python, significantly optimizing the mine-to-mill process. This practical approach is a game-changer in the mining industry. Classifying a geomet dataset into units of similar characteristics (properties of the ore) is an important outcome of a geomet study. This approach simplifies data classification, allowing for class-by-class process modelling, which improves the decision-making process in mine planning and development. Classifying a geomet dataset involves using grade, lithology, and test work data (if available) to create blocks of similar characteristics, known as ‘geomet units.’ Compared to conventional methodologies, these units provide context and empirical evidence that can be more accurately mapped onto block-by-block process flowsheet development and net present value (NPV) estimation. This robust classification method reduces a project's technical risks and influences the initial mine planning sequence to maximise profitability. Defining robust geomet units with data sets with similar material is challenging due to the vast amounts of data available and the database's high heterogeneity. The methodology's purpose is to minimise time-consuming low-value-adding aspects of geometallurgy. The approach is different for a greenfield and a brownfield study, as all the valuable data in a brownfield process can be utilised to define the geomet units. Python has various libraries providing multiple machine-learning algorithms to assist in classification. The k-means algorithm is used for clustering, and the SHapley Additive exPlanations (SHAP) method is used to quantify the effect of each feature on the clustering results. However, even with automation, the methodology still requires a keen eye to account for the nuances that appear from project to project.

Oct 1, 2024

By Joseph Sawicz

By now, the concept of remotely controlling heavy equipment in underground mines has become commonplace. Personnel safety is the biggest justifier for remote control, followed by an inherent cost saving (in certain cases) when wireless video is added to the mix. There are a handful of vendors targeting this need, and for years the mines have remained loyal to their brand. But as the number of remote-control related accidents and maintenance costs increase it forces our industry to take another look at this commonplace concept. And as the blinders are taken off, the mines are getting the revelation that not all remote control systems were created equally. This paper highlights the differences between various remote control systems, and then moves into an in-depth look at HARD-LINE?s package which drastically cuts maintenance costs, and also provides a solid investment toward full Tele-operation.

Apr 1, 2005

By Andrew J. Freyman, Graham T. Armstrong

"In September, 1968, a survey of operating mines in the Yukon and the Northwest Territories was undertaken to determine the role of Indigenes (Indian, Metis, Eskimo) on the mines, and the attitude of mine management to these employees. The operating mines in the Territories had (at that date) a total employment of 2,002 men, of which 91 (4.5 per cent) were Indigenes. Indigenes make up 45 per cent of the Territorial population (18 per cent in the Yukon and 63 percent in the Northwest Territories). The paper documents some of the problems associated with indigenous employment in mines. A study was undertaken to determine the role of Indigenes (Indians, Metis, Eskimos) in operating mines in the Yukon and in the North-west Territories. In addition to the mines north of the 60th parallel, the experience of several other Canadian mines was examined. The general picture obtained is considered to be representative of the Canadian mining industry."

Jan 1, 1969

By J. D. Galloway

The mining industry of British Columbia continues to grow steadily in importance. The gross value of the production in 1925, sixty-two and a half million dollars, was a record, and ali indications point to the 1926 output registering a still higher figure. In an industry such as mining, where production means the depletion of known ore reserves, the discovery and development of new 'ore-deposits is of the utmost importance. To maintain and increase production, steady development is essential. In this respect, the record of the last three years in British Columbia mining is most satisfactory, as in this period more real development has been carried on than in any similar period in the history of mining in the Province. Prospecting, or the search for new ore-bodies, has also been fairly active, but comparatively few important new discoveries have been reported in the past few years. The mineral output of British Columbia consists of Iode minerals, coat and coke, and building materials. In 1925 the value of the output of these three classes of products was, respectively, about 46, 13, and 3 million dollars. The industry as a whole embraces the mining of these materials, and the treatment and manufacturing processes involved in preparing the various products for the market.

Jan 1, 1926

By Enzo Angeles, Desmond Nanchengwa, Lee Julian, Julian Ruiseco

Since the early 1980s, surface hard-rock mining companies have searched for a blast movement model to enable grade control optimization efforts. Significant time and money were spent attempting to create blast simulations to aid post-blast grade control. Despite nearly 40 years of effort, practical blast movement models remained elusive until computing power reached levels that make real-time simulation possible. From the mid-1990s, mines have been creating in-situ grade control polygons and translating the polygon nodes horizontally to account for blast movement. In many cases, objects are placed in the blast volume and located post-blast to provide local vectors for these node translations. This method was always a compromise between practicality (2D) and reality (3D), but it was the only viable solution that matched the needs of operations. This study considers 21 blasts and evaluates the incremental value achieved by new processes unlocked through 3D modelling, while investigating challenges, limitations, and opportunities for each method.

Jan 1, 2023

By J. F. Wright

Introduction Previous to 1924 the mining fields of Manitoba and adjoining territory had not been prospected in detail, and the reports of the exploration of the mineral discoveries to that date had been discouraging. As a result of the apparent failure of all the mining operations, some considered that geological conditions in the country westward from lake Superior extending across western Ontario, eastern and northern Manitoba, and northern Saskatchewan, were different from those in the northeastern part of Ontario, where large gold mines had been developed. Discoveries of importance thus were necessary to renew interest in the mining possibilities of this part of the Canadian Shield, and the successful operations at Flin Flon and Howey in large part were responsible for the beginning of the present activity in what may be described as the part of the pre-Cambrian Shield within central Canada. In Manitoba, the more important developments at present are in the Central Manitoba, Gods Lake, and Knee Lake fields. The large area from west of Flin Flon east to Herb Lake, also, is being explored carefully for gold deposits of merit. A number of properties in Red Lake, Woman Lake, and Pickle Crow areas are being drilled and explored underground. Many of the mines of the Lake of the Woods area, that were producing gold 30 years ago, are re-opened, and new prospects in this field and in the country to the east are being explored. The recent development of Little Long Lac mine in an area near the railway, and considered by some to have been thoroughly prospected years ago, has stimulated interest in the areas formerly prospected. In the autumn of 1934, the belts of greenstone and sediments in the country east of lake Nipigon were staked, and deposits in these fields will be explored in detail this year. This paper is presented to discuss the general features of the geology and gold deposits of the various prospecting fields in Manitoba and adjoining territory. Details of a number of the areas and mines will be presented at this meeting in papers by Barton on Little Long Lac, Tanton on Sturgeon River, Baker on Gods Lake, and Brownell and Kinkel on Flin Flon. Although mining was not active in most of this territory previous to 1930, geologists of the various government departments continued field studies and interesting reports were issued.

Jan 1, 1935

By Jiachen Wang

Longwall top-coal caving mining is one of the major mining methods for extracting thick coal seams in China. The top-coal caving longwall mining was began to use in the 1980s in China, and got the rapid development. The development of the top-coal caving mining technology in China, the achievements and the theoretical aspects progress of this method are described in detail in this paper. And the main technical model of China's top-coal caving mining is introduced in this paper. This paper also introduces the application of large-cutting-height mining in China and the technical level it has reached.

Aug 1, 2013

By I. M. Marshall

SOME years ago the writer had the opportunity to plumb a number of mine-shafts, each of which presented various conditions and difficulties. This afforded the chance to compare several methods of shaft plumbing in the light of ease and rapidity. This comparison led to the development of an adaption of the Weisbach, or approximate alignment, method, to three wires in a single shaft. Professor Weisbach, some time prior to 1850, introduced his method of shaft plumbing by triangulation on but two wires, and was the first to show that a triangle of very narrow shape is the best for this purpose. THE WEISBACH METHOD The two-wire method, using a Weisbach triangle, is described in several .English text-books on mine surveying and is used frequently in various parts of the world, but in Canada it is almost unknown. The writer has described an example of this two-wire method (1), but a brief resumé here may clarify the explanation of its application to three wires. In this two-wire method, instead of endeavouring accurately to align the instrument with the wires, it is set only in approximate alignment, and the small angle formed at the instrument is measured. This is expressed graphically in Figure l, where C represents the position of the instrument and A and B the positions of the wires. The sides of the triangle are measured as well as the angle ACB, and the angles at B and A are found by applying the Sine Rule or the formula

Jan 1, 1938

By W. L. Uglow

In recent years, the microscope has come to be recognized as a valuable aid to engineers whose business is the discovery, development, concentration or reduction of metallic ores. In many of the large treatment plants microscopical research has already an important status; and in the hands of efficient operators the microscope has indicated methods of solving ore problems resulting in the saving of thousands of dollars that otherwise might have been lost in tailings, or expended in freight rates or smelter charges. Failure to procure all the information that the microscope can supply concerning the physical and mineralogical characteristics of complex ores has in many cases led to the construction of unsuitable concentrators, just as the failure to investigate in detail the geological conditions of an ore deposit has often results in the squandering of money on shaft sinking, and mechanical installations which subsequent development of the deposit failed to justify. The great progress recently made in the selective separation of minerals by means of the various processes of flotation and leaching brings strongly to our attention, the scope of the field in which microscopical methods may be advantageously employed. The microscope enables one to observe the minute details of rock, ore, gangue, concentrate, tailing, matte, slag and metal, that are invisible to the naked eye. Furthermore, the technique of microscopal research has been so highly developed that a microscopist can not only observe, but deter-mine the compositions and measure the diameters of the mineral constituents in the ore to be treated. Magnifications of these constituents up to 3,000 diameters may be produced by the proper combination of eyepiece, objective, and projection apparatus, and the images thus viewed may be photographed through the microscope, and permanent records made of them.

Jan 1, 1924

By Kan Xing

This paper introduces common detrimental consequences to the environment from mining in the Beijing West Mining Area. For example, ongoing mining operations can cause the following environmental deterioration: rock burst, roof rises, roof falls and inrush (Pit dash for ward water). Post-closure, after minerals resources are exhausted, the following environmental issues may remain: landslides (collapse, and mud-rock flow), dropping or exhausted water tables, water pollution, desertification and soil erosion, water accumulation, Slay endanger, ground subsidence, and causal factors in seismic activity. This paper analyzes this wide range of environmental consequences of mining, and offers a theoretical foundation to underpin a corresponding management scheme.

Aug 1, 2013

By W. Kempson

"Mining Companies have producing assets in increasingly diverse portions of the world. It is not uncommon that the owner, the design team, the mine contractors and the operators are all based in different countries. While these assets are always subject to the regulatory requirement of those countries there have not been international standards available to review and evaluate these assets. This becomes particularly important when considering safety critical items such as tailings dams, vertical shaft systems and autonomous vehicles to highlight a few. The work currently being completed in ISO ensures these standards will be available and will be generated by and subscribed to on an international basis, thus removing the potential for patriotic partisanship and ensuring safe and predictable systems are installed. This paper will discuss the benefits of the international standards, the structure of the teams and working groups who are generating these standards as well as the process by which the standards are generated. This will allow insight into the creation of the standard and will aim to demonstrate the “neutral” and technically strong manner in which the generation of these standards is achieved. In addition, the paper will discuss the standards which have been produced in the last five years as well as the current standards which are in place. The finale will discuss upcoming work and the timelines in which it is anticipated these will be completed. INTRODUCTION Mining Companies have producing assets in increasingly diverse portions of the world. While these assets are always subject to the regulatory requirement of those countries, there have not been international standards available to review and evaluate these assets. This becomes particularly important when considering safety critical areas such as vertical shaft systems, tailings dams and autonomous vehicles to highlight a couple. The work currently being completed in the International Organization for Standardization (ISO) ensure these standards will be available and will be generated by and subscribed to on an international basis, thus removing the potential for patriotic partisanship and ensuring safe and predictable systems are installed. The ISO/TC 82 – Mining was founded in 1955. This was an active committee until it was thought that the standards at the time were adequate and the Technical Committee was put on “Care and Maintenance”. In 2012 countries lobbied ISO to pull this committee from dormancy and restart it, this happened in in the same year."

Jan 1, 2019

By Robert T. McKnight

"Traditional techniques for valuing resource projects companies have been primarily based on discounted cashflow methods (DCF) or by comparison to similar projects with an apparent market capitalization. Many resource projects are really forms of options to invest rather than a future cashflow stream. Employing the DCF method to value a resource project which is really an option to invest, can dramatically underestimate the real value of the project. The analytical tools required to evaluate options, while more complicated than the usual spreadsheets used for DCF, are becoming more easily available and usable by managers. This paper will discuss the background of options valuation and some of the tools which will make it easier for managers to estimate the value of projects and companies which have significant real option values.ResumeBob McKnight is a graduate of the University of British Columbia in Geological Engineering, supplemented by an MBA from Simon Fraser University. Following several years in the oil patch with Cities Service and Brascan, Bob returned to Vancouver in 1979 to work for Wright Engineers. He subsequently went on to work for Cassiar Mining, Getty Resources and Endeavour Financial before joining Pincock Allen & Holt Ltd. in 1998. His experience ranges from exploration to feasibility studies, financial evaluations of mining and oil & gas projects, due diligence, project finance, valuations and mergers and acquisitions. He has extensive international mining experience pertaining to such countries as Chile, Mexico, Uruguay, Thailand, Indonesia, Angola, Papua New Guinea, Kazakhstan.What are Options?Options have been around for centuries. They were familiar to Roman and Phoenician traders who were shipping cargoes from Mediterranean seaports. In the financial world, options are types of contracts that generally include the right, but not the obligation, to buy or sell a share, currency or commodity. The underlying commodity price or share price changes are assumed to be lognormally distributed. In this context, options are of two general types, ""call"" options and ""put"" options. Call options have the characteristic of having the right to buy a tradable commodity or currency at a predetermined price for a specified period of time. For the owner of call options, they become more valuable as the price of the underlying commodity increases. For the seller of call options, these options become an increasing liability as commodity prices rise, since there is the obligation to sell the commodity at a predetermined (perhaps lower-than-market) price. This characteristic of call options recently became high profile with the sharp rise in gold prices last year. The value of gold call options sold by certain producers increased their associated liabilities to the point where margin calls were made."

Jan 1, 2003

By Hung-Ming Chen

This paper presents a Cloud-based system framework for providing a web-based building information model (BIM) service. Cloud computing technologies were used to develop a BIM data center, which can handle the big data of massive BIMs using multiple servers in a distributed manner. In addition, the system allows multiple users to access the BIM data center online to submit and review BIMs concurrently. In this study, the advanced technologies/tools of web development and Cloud computing were applied and incorporated to develop a prototype system, named CloudBIM. On the client side, this study applied WebGL and HTML5 in the web-based interface development to achieve the 3D display of BIMs and the dynamic interaction with viewers through browsers. Users can access the services of CloudBIM by using PCs, laptops and tablets anytime anywhere to view the 3D model via browsers, which support WebGL. On the server side, this study used Apache Hadoop, an open-sourced distributed file system based on Google?s technologies, to establish a BIM data center. The Hadoop Distributed File System (HDFS) can utilize multiple servers to provide mass storage spaces in a distributed manner. Based on the use of Apache HBase, which provides Bigtable-like structured storage for HDFS, this study proposes database schema for storing the information from massive BIMs in two bigtables, named Object table and Property table respectively. In addition, Hadoop MapReduce, a Hadoop component for the parallel processing of large data sets, is utilized for model data acquisition by parsing the IFC files of uploaded models in parallel.

Aug 1, 2013

By D. A. MacLeod

DURING the past fourteen months, dust surveys have been made at thirty-six mines in the Province. These surveys are made to determine the concentration of dust in the mine atmosphere, the flow of air through the mine, the methods adopted to prevent the generation of dust, and the measures taken for its elimination. When high concentrations of dust are encountered, suggestions are given for its prevention ?and elimination wherever possible. Dust sampling is absolutely necessary to determine the effectiveness of any measure taken in the prevention and elimination of dust in the mine workings. Consequently, more time has been spent on this phase of the work than on any other. The apparatus used is the Devers circular konimeter and Zeiss microscope. At various mines, the Zeiss konimeter is used, and the dust counts taken by the two instruments have given results that are closely comparable; so much so that either instrument can be used with confidence and the results obtained will compare in accuracy with those obtained by the methods used in Ontario and South Africa. Before the Workmen's Compensation Act Amendment Act was passed in November, 1936, most of the mine operators were already keenly interested in the prevention of silicosis. This interest has been intensified at all the mines, and measures have been adopted to decrease the amount of dust in the mine atmosphere. Several operators have spent a large amount of time and money in bettering these conditions, and have met with decided success. Practically all others are adopting the known methods of prevention, suppression, and elimination of dust, that apply to their ?particular mines. To prevent the production of dust in underground workings should be the first, as it is the most important, aim, especially during the time the men are underground. An atmosphere free of dust cannot be obtained, but measures can be adopted to lower the concentration that is found? in the average mine.

Jan 1, 1939

By Shanjun Mao

This paper summarizes current achievements of Digital Mining in China, puts forward the concept, framework and key technology of Smarter Mining, and finally points out that there is still a long way to go in order to acheive Smarter mining.

Aug 1, 2013