Search Documents

By A. Saigal

The effect of temperature on the cutting forces during machining of alumina reinforced aluminum composites was investigated, Aluminum 6061, 10% Al2O3 reinforced composite and 20% Al2O3 reinforced composite were tested, A 5/8-inch diameter high-speed steel end mill, a Micro 100 TiN coated single edge endmill cutter and a two-fluted solid carbide insert cutter were used for tooling, The results, in general, showed an increase in the cutting forces as the temperature of the material increased, From the raw data, there are temperatures ranges in which the force data did decrease but they were insignificant with regards to predicting a downward trend. A regression analysis was used to understand which variables had the greatest affect on the forces being generated, The correlation and regression analysis showed that at 600 rpm (velocity: HSS- 98,2 sfpm, Micro 100 cutter - 78,5 sfpm, solid carbide cutter - 192,4 sfpm) the tooling, the workpiece material, built up edge, and temperature were statistically significant factors in the test, Tooling was a significant variable in all testing, The smallest forces recorded during machining were generated with the solid carbide two-fluted endmill cutter, Visually, the solid carbide tooling produced a better surface finish during the testing which made it the tool of choice, In addition, the force data proved that as the cutting speeds were increased, the cutting forces decreased.

Jan 1, 2005

By H. Somekawa

The fracture toughness and deformation structures an AZ31 magnesium alloy processed by equal-channel-angular extrusion (ECAE) were investigated. The average grain sizes of as-ECAE and annealed-ECAE alloys were 4.0 and 16.3 µm, respectively. The plane-strain fracture toughness, Kip, in as-ECAE and annealed-ECAE were estimated to be 27.3 and 23.5 MPam1/2, respectively, by stretched zone analysis. The fracture toughness indicated higher value with grain refinement. From optical microstructural observations in samples after fracture toughness tests, although deformation twins were observed in annealed-ECAE, no deformation twins were observed in as-ECAE. From TEM observations, the dislocations on basal and non-basal planes were activated in as-ECAE. With grain refinement, the activations of dislocations on both basal and non-basal planes were possibly related to the reduction in formation of deformation twins in as-ECAE. In addition, in comparison with direct extruded process, ECAE process was more effective method to improve the fracture toughness in magnesium alloys.

Jan 1, 2006

By G. K. Quainoo

Investigation by researchers on the application of various thermo-mechanical process histories on 6000 series aluminum alloys have found improvements in mechanical properties of these alloys. However, natural aging, which is unavoidable in the automotive processing line, has been found to have deleterious effect on subsequent artificial aging properties in these alloys. In this study, the evolution of yield strength during natural aging modeled by Lloyd and Gupta has been adapted to investigate the effect of cold deformation on the natural aging kinetics in AA61 11 by means of tensile testing, differential scanning calorimeter (DSC) and scanning electron microscopy (SEM). Also, intermetallic particles in the alloy were extracted from the matrix and XRD performed on them to ascertain their composition and their role on the kinetics in the alloy. The results show that cold work effect on the natural aging kinetics of AA6111 is in very good agreement with the model proposed by Lloyd and Gupta. The kinetics of natural aging in AA6111 aluminum also decreases with increasing level of cold work. This is attributed to dislocations serving as sinks which consume quenched-in vacancies formed during the early stages of clustering. The phases of the intermetallic particles identified in AA6111 are those of a-A15Mn12Si7 and a-A15MnSi.

Jan 1, 2007

By Roger Lacroix

Presentation outline Project definition Characterization of mine ventilation systems Strategies in place and results Detailed study (2 mines) Other potential energy savings Conclusions Next steps

Feb 1, 2008

By K. Fumimura, T. Nishimura, M. Kohno

When applying numerical techniques to problems of deformation of rocks, the body to be analyzed is divided into small portions and is represented by a system of points linked together with the neighboring points. In the so-called distinct element modeling, the particles in the system are directly connected by springs and a contact law is used to specify forces on the particles to simulate the mechanical behavior of the body. The relation between the spring stiffness and commonly measured material properties, such as the Young’s modulus and the Poisson’s ratio, should be known a priori. For the general case of a random packing of particles, the relation is found by means of a process in which a system of particles and set of parameters are prepared to simulate a set of specimen-size test and then the input parameters are chosen to match the measured material properties. The validity of the numerical result is only demonstrated by comparison model behaviors with the measured responses. The process includes trial-and-error manner, therefore, no model is complete to reproduce the mechanical properties. In this paper, a relation between the spring stiffness and the elastic constants; the Young’s modulus and the Poisson’s ratio, is introduced to a three-dimensional distinct lattice spring method. Two simple numerical examples will be presented to demonstrate the performance of the method with the procedure for the determination of the spring stiffness.

Jan 1, 2015

By John W. Korczak

The use of geological and grade block models has been standard practice in mine design for many years now, with a wide range of software available for creation and analysis. Although geotechnical parameters are of vital importance to mine planning there is very little in the way of commercially available systems for integrating geotechnical data into the mine planning and design process. Sirovision is a new technology developed by the CSIRO (Commonwealth Scientific and Industrial Research Organization) in Australia for automated, safe and accurate 3D mapping of geological and geotechnical features. Datamine has integrated this capability into its product range so that Sirovision has become an integral part of the day-to-day mapping, mine geology and geological / geotechnical modeling in both open pit and underground mine environments. This is the first integrated underground application of Sirovision from Datamine collaboration with Xstrata Nickel at the Nickel Rim South Project. This paper discusses the role of Sirovision in collecting the raw data required for geological and geotechnical analysis and the interpretation in a quick, safe, auditable and reproducible manner.

May 1, 2009

By Andrew Artzer, Michael Moats, Jack Bender

Antimony and bismuth in copper electrorefining electrolytes can cause cathode contamination, leading to the careful control of their concentrations. This study examined the laboratory scale removal of bismuth and antimony from an electrorefining electrolyte using a solvent extraction mini-pilot plant. The ability of a proprietary phosphonic acid ester extractant (REX-2) in a commercial diluent was studied in a simulated commercial setting. Antimony and bismuth were both extracted effectively from the electrolyte (72% Bi and 70% Sb removed) and Bi was effectively stripped (92% Bi recovered) with 400 g/L sulfuric acid. A final strip solution was obtained from the SX circuit containing 0.36 g/L Bi, 0.043 g/L Sb, 1.3 g/L Cu, and 0.18 g/L As. Unfortunately, most of the extracted Sb remained in the organic phase. Following the pilot study, experiments were performed to examine the precipitation of bismuth from the aqueous strip phase and the removal of antimony loaded on to REX-2. INTRODUCTION For many years, antimony and bismuth have been some of the most problematic impurities in copper electrorefining (ER) (Bardwell & Lapee, 1933). Along with surface roughening, high concentrations of Sb and Bi can contaminate the copper cathode and precipitate at the copper grain boundaries. This drastically reduces the drawing ability of the metal (Bender & Emmerich, 2016). For these reasons, it is necessary to control Sb and Bi concentration in the cathode, which is done by controlling their concentration in the electrolyte. Conventionally, Sb and Bi concentrations are controlled by maintaining a proper As/(Sb+Bi) molar ratio in the anode and arsenic concentration in the electrolyte. Antimony and bismuth are removed during electrolyte purification using liberators (electrowinning cells) and/or ion exchange. Liberators treat an electrolyte bleed stream from the ER circuit and electrodeposit increasingly impure copper as the copper concentration of the solution decreases. Traditionally, first stage liberators reduce the copper concentration from ~45 g/L to ~15 g/L and produce saleable copper. Second stage liberators decrease the copper concentration to ~8 g/L (Biswas & Davenport, 1980) which results in contaminated cathode that is returned to anode production (Biswas & Davenport, 1980; Wang, 2004). Further electrolyte purification is not always required but third stage liberators can be used to reduce copper concentration below 2 g/L which results in significant removal of As, Sb and Bi and very impure deposits which are recycled to a smelter or used for As production. However, liberators do not have very high energy efficiency (Acharya, 2014; Ando & Tsuchida, 1997) and below 0.5 g/L copper, highly toxic arsine gas may form (Biswas & Davenport, 1980).

Jan 1, 2019

By A. G. Roach

IT IS generally stated that the gold ores of Nova Scotia are free-milling, and for the most part this is true. However, there is a certain proportion of the gold finely disseminated throughout the sulphides, notably arsenopyrite, and this gold is definitely not recoverable as 'free-milling' gold by amalgamation. The proportion of free-milling gold to total gold seems to vary widely in different localities in the Province and is lowest in deposits of the fissure-vein type. The problem of recovery of these relatively recalcitrant values is usually one of economics, in some plac.es a simple gravity concentrate being of such low tenor that its extraction and subsequent disposal will not bear the costs involved. In other cases, such a high percentage of values escapes from the mortars and plates that concentration is definitely indicated. The size of the mining operation is also an important factor. In the large majority of cases, however, some concentrating step is warranted, even if the resulting concentrate is stock-piled until sufficient has accumulated to justify further treatment.

Jan 1, 1940

By Robert Boutilier

For more information on what the social licence means, see the following: Joyce, S. and Thomson, I. 2000. Earning a social licence to operate: Social acceptability and resource development in Latin America. The Canadian Mining and Metallurgical Bulletin, 93(1037) Nelson, J. and Scoble, M. 2006. Social License to Operate: Issues of Situational Analysis and Process. Vancouver, BC: Department of Mining Engineering, University of British Colombia. Thomson, I. and Boutilier, R.G. 2010. The Social License to Operate In P.Darling, (Ed.), SME Mining Engineering Handbook: Littleton, CO: Society for Mining, Metallurgy and Exploration. Much of what has been written and said about the social license to operate focuses on what the company has to do or not do. But the social license is a two-sided relationship. We also need to look at what the community has to do, or not do, in order to be capable of issuing a social license that is meaningful.

May 1, 2010

By S. V. Burr

"IntroductionOne of the more puzzling geological enigmas, in the writer's opinion, is how rock can move sideways with respect to other rock. In the writer's study of regional northwest-southeast folding in North America (Burr, 1980), he may have found the answer to horizontal offset.Horizontal OffsetSideways movement or horizontal offset does not mean that the movement was, or is, horizontal. As indicated below, the actual movement may be at a high angle from the horizontal. However, it is the horizontal VECTOR, or offset, which is measured on surface by geologists. Vertical movements (thrust, normal, reverse) can be understood, as they involve blocks of rock , generally separated on four to six sides, which have been pushed up or subsided. Vertical faulting across dipping strata can produce APPARENT horizontal offsets. However, this thesis deals only with ACTUAL offsets.The ProblemFigure 1 is a plan view of a simple hypothetical horizontal offset. Three vertical dykes are intersected by a fault lineament. Two dykes exhibit no movement; the middle dyke has been offset a distance (a). Vertical faulting would have produced no horizontal offset. How can a horizontal distance (a) disappear or appear? Rock expands or contracts in infinitesimal amounts.SolutionThe map (Burr, 1980) shows the writer's interpretation of regional northwest-trending folds in Ontario. The writer made two observations about horizontal offsets during his thirty year study of these folds:1) All major horizontal fault lineaments strike at a high angle to the northwest fold axes. Many of the northwest-trending lineaments are fault s, but their movement is essentially vertical.2) Close to many of the known horizontal offsets (and several lineaments), there are areas where plunge reversals are so frequent and close together it is impossible to draw in all the fold axes at a scale of 1 inch = 4 miles, and, in the highly faulted Espanola area southwest of Sudbury, Ontario, all the indicated folds cannot be easily separated at a scale of 1 inch = 1 mile. The writer has observed folds less than 30 feet apart next to the strong Puskitamica-Chibougamau fault in northern Quebec."

Jan 1, 1982

By C. Cortés

Flotation is a highly interactive process where a change or disturbance in any part of the circuit results in different final grades and recoveries. This high variability of the circuit metallurgical performance complicates the diagnosis of the scavenger stage at the end of the line, as copper losses in the final tailings are erratic and not totally a consequence of problems in the scavenger section. The assessment of the scavenger performance requires a more elaborated procedure than that used for others stages of the circuit. This communication describes the application of an approach that combines results of laboratory flotation tests with those of surveys performed at the plant. The approach is based on running surveys in one of the circuit lines to collect samples for determining grade vs. recovery curves for total mass and size-by-size fractions. Full mineralogical and liberation analyses are also considered on some samples of the feed and tailings streams selected to have a range of feed grades. A separate sample of the feed is used to run laboratory flotation tests to determine optimum flotation time. Two additional pieces of information are the effect of operating variables on recovery, determined through a test program based on design of experiment techniques, and operational data on every cell in the line gathered by visual observation. The application of this approach to one of the scavenger lines at Los Colorados concentrator (Minera Escondida, BHP Billiton) is demonstrated.

Jan 1, 2007

By J. Oliveira, A. R. Barnes, R. Pandher

Sub-stoichiometric roasting of arsenic-bearing copper ores is a well established practice. However, ores containing calcium commonly prove challenging where very low arsenic levels are desired, but the reasons for this phenomenon have largely been speculative. In the course of treating arsenicbearing copper ores by partial roasting in fluid bed reactors, XPS encountered one of these Ca-bearing ores which proved a challenge to roast to acceptably low levels of arsenic. Mineralogical examination of the calcines using a combination of XRD (X-ray diffraction), QEMSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) and EPMA (Electron Probe Micro-Analysis) helped to identify the arsenic bearing species and assisted in developing a workable theory on the sequence of reactions occurring during the roast. With the assistance of thermo-chemical modelling, this allowed adjustment of the roasting conditions to minimise the amount of arsenic retention in the calcine in spite of the presence of calcium in the ore and advance the roasting program to a commercially acceptable solution.

Jan 1, 2014

By Chandrakala Kari, Divyang Shah, Lakshmi Kanth Reddy, Kaushik Vakil, Sanjay Sarkar, Bhavin Desai

Gases rich in sulfur dioxide generated as a by-product of smelting and converting operations of copper concentrate contain selenium apart from zinc, lead, copper, cadmium, bismuth, antimony, and arsenic. The gaseous stream is heat exchanged in waste heat boiler, dust collected in electrostatic precipitator followed by cleaning in reverse jet scrubber to remove fumes, halogens and fine dust before passing to DCDA Monsanto catalytic converter to produce commercial grade sulfuric acid. The gas cleaning section of the acid plant uses water to scrub the smelting gases. During scrubbing, precipitated solids, known as sludge, settles at the bottom of the reverse jet scrubber containing 30 to 40 wt% copper and selenium up to 40 wt% selenium. In the existing process, the sludge collected during scrubber cleaning process is directly recycled to the smelter for copper recovery. However, the selenium is expected to again vaporize due to high oxidation potential during smelting and converting, causing accumulation of selenium in sludge. In present investigation, a roasting process has been developed to recover the selenium from acid plant sludge before charging it to smelter for copper recovery. Selenium is associated with copper in acid plant sludge as copper selenide, as determined by X-ray diffraction and electron microscopy. Thermodynamic and thermo-gravimetry study revealed that the copper selenide phase present in the sludge was amenable to oxidation at 600°C forming oxides of copper and selenium (Cu-Se-O). However, the dissociation of selenium from the copper oxide was made possible by sulfatation using sulfur dioxide between 450°C to 600°C, resulting into the formation of CuSO4(s) and SeO2(g). Lab scale experiments were carried out in vertical tubular furnace to determine the optimum roasting conditions with respect to roasting time, temperature and molar ratio of O2:SO2. Using these optimum conditions, selenium up to 90 wt. % in the form of SeO2 vapors could be recovered from the acid plant sludge in a large scale commercial roaster. Roasted sludge free from selenium and containing oxides and sulfates of copper could now be recycled in the smelter for copper recovery. INTRODUCTION There is an increasing demand for minor metals due to their use in innovative technologies. Similarly, the increase in demand for selenium is expected due to disruption in sectors related to renewable energy and photovoltaic battery. Selenium is a chalcogen and a non-metal with black or red crystalline appearance. Selenium is used in the glass industry to decolorize glass and to make red-colored glasses and enamels. It is also used in solar cells and as a photographic toner. Selenium is used as a brasses in stainless steel to improve its machinability. Selenium sulfide is used in anti-dandruff shampoos. In spite of the toxicity of its compounds, selenium is also an essential trace element for humans and animals. Selenium occasionally occurs free in nature, but more often occurs as selenides of iron, lead, silver and copper. There is an urgent need for the development of new methods for selenium recovery from the existing resources. Commercially, selenium is obtained only from anode mud produced during electrolytic refinery of copper.

Jan 1, 2019

By Frank D. Shepherd

THE Gunnar Gold Mines property is on the west shore of Beresford lake, in the Rice Lake mining division, southeastern Manitoba. Gold was first discovered in place in the Rice-Beresford Lakes area in 1911 on the Gabrielle claim, now included in the San Antonio Mines property at Rice lake. Following an eastward trend of favourable prospecting ground, promising showings were next staked in the vicinity of Long lake during the years 1915 and 1916. At that time, William Walton and associates, among them Gilbert LaBine, staked the Eldorado vein, north of Long lake, and Eldorado Gold Mines, Limited, was formed to develop the property a Company that, later, was to become widely known through successful operation of its radium-silver mine at Great Bear lake, Northwest Territories. Continuing eastward from Long lake, Walton and his partners, Gunnar Berg, Leo Seaberg, and Wm. Quesnel, staked claims during the years 1920-24 in the vicinity of Beresford lake which, later, were to become incorporated into the Gunnar Gold Mines property. The presence of gold-bearing quartz on these claims had been known from the time they were staked, but an opportunity to consolidate them into a group was not forth-coming until early in the year 1933. Although promising gold showings had been disclosed during the performance of assessment work on individual claims, no continuous mineralization having mine-making possibilities was discovered until after the consolidation of the entire group. From this stage onward, progress was rapid. Active exploration was begun on August 1st, 1933, and late in October James Houston reported favourably on the property. On October 27th, Gunnar Gold Mines, Limited, was incorporated in the Province of Ontario to develop and operate the property. The Company is also registered in Manitoba. The authorized capitalization is 3,000,000 shares of $1.00 par value. Gilbert LaBine was appointed president of the Company, with James Houston as mine manager. Following completion of a diamond-drilling programme, planned in 1933, it was decided to install a mine plant capable of carrying development to a depth of 1,000 feet. A transmission line, 5 miles in length, was built to the Great Falls-Central Manitoba line of the Manitoba Power Company, Limited.

Jan 1, 1939

By Michael E. Charles, Jaroslav J. Vocadlo

"The hydraulic transport of solids through pipelines can have many advantages over other modes of transport. Numerous successful applications both within plants and over longer distances have demonstrated the technical and economic feasibility of slurry pipelining. Solids successfully transported include kaolin, coal, iron ore, gilsonite and limestone, and others, such as sulphur and potash, are likely to be transported in Canada in the near future. However, though the technology of solids pipelining is quite advanced the underlying principles have not yet been formulated past the semi-empirical stage. The main objective of this paper is to present a discussion of the important technical and economic considerations in the design of so lids pipeline systems by reference to typical data. The Worthington slurry pumps and pilot facilities are briefly described."

Jan 1, 1972

By Fulchand Shende

Around the world many potash mines experience brine inflow problems. The presence of brine in underground excavations may induce structural and stability problems. A study has been carried out to simulate the effect of brine on the performance of pillar support. The testing program consisted of loading potash specimens in a creep frame, and simulating inflows by continuously pumping brine into an experimental cell. Brine temperatures and load conditions were varied to simulate several mining and inflow conditions. Specimens were fitted with acoustic emission transducers to monitor energy emissions during an eight-hour test duration. Samples of brine were also collected to provide K+ and Na+ concentration data necessary for an accurate assessment of the dissolution process. Test results indicated that dissolution rates are highly dependent on brine temperature and load conditions. Loads approaching 50% UCS tend to generate very high rates of energy emissions, often leading to the failure of the simulated pillars. This study demonstrated that acoustic emission could be effectively used for predicting the performance of pillars when exposed to inflow brine.

May 1, 2001

By D. K. Sarkar, Jiawei Xiong

"Self-assembled monolayers (SAM) on the aluminum substrates are used as the adhesion promoter between two aluminum substrates when bonded with the adhesive in adhesive bonding technology. Traditional surface analysis tools are not capable of identifying the presence of SAM on a surface; therefore, EIS has been used to determine their presence on the aluminum substrates. In this study SAMs have been deposited on aluminum using the monomer of (3-Glycidyloxypropyl)trimethoxysilane (GPTS) organosilane. AA6061 aluminum alloys substrates were chemically cleaned with NaOH and HNO3 to remove the native oxides, followed by immersion in silane solutions. In a second method, SAMs were prepared by applying a spin coating of silane solution to the samples. The prepared SAM coated aluminum samples were analysed by EIS in the three electrode corrosion cell using a diluted alkaline solution. The impedance of the SAM coated aluminum is found be higher than the as-received aluminum. It has been also observed that the open circuit potential (OCP) of the SAM coated aluminum is higher than the as-received aluminum. Both elevated values of the impedance and OCP confirm the presence of SAM on aluminum.INTRODUCTIONSelf-assembly (Schreiber, 2000) is defined as the spontaneous formation of complex hierarchical structures from pre-designed building blocks, typically involving multiple energy scales and multiple degrees of freedom. Generally speaking, SAMs are created by the chemisorption of ""head groups"" onto a substrate from either the vapor or liquid phase followed by a slow organization of ""tail groups"" of a molecule. Typically, head groups are connected to a molecular chain in which the terminal end can be functionalized with groups such as –OH, –NH2, –COOH, or –SH to vary the wetting and interfacial properties (Chauhan et al., 2007; Ulman, 1996; Vashist, Lam, Hrapovic, Male, & Luong, 2014). Though there exist several methods to prepare SAM (Chauhan et al., 2007; Chen, Yang, & Zhang, 2014; Cho, Park, Jon, & Choi, 2007; Igor Luzinov, 2000; Reis, de Melo, & Costa, 2006; Song, Zhai, Wang, & Jiang, 2006; Sugimura, Hozumi, Kameyama, & Takai, 2002; Vashist et al., 2014), the two methods vapor phase (Song et al., 2006; Sugimura et al., 2002) and solution(Chen et al., 2014; Igor Luzinov, 2000) are commonly used. Recently, many articles have been published on the fabrication of superhydrophobic surfaces with SAM technology (Cho et al., 2007; Pan, Shen, Shang, & Xing, 2012; Siddaramanna, Saleema, & Sarkar, 2014; Song et al., 2006). Brassard, Sarkar, and Perron (2011) successfully obtained a superhydrophobic film by applying fluoroalkylsilane via self-assembly on monodispersive silica. SAMs are also reported as good candidates for anti-corrosion and adhesion promotion (Chen et al., 2014; Saleema, Sarkar, Paynter, Gallant, & Eskandarian, 2012). However, papers on the characterization of SAM properties are rarely seen. The most commonly used substrate for SAM is silicon and the method implemented is scanning probe microscopy (SPM) such as atomic force microscope (AFM) (Igor Luzinov, 2000; Moores, 2011; Zhang, 2003, 2005). Igor Luzinov (2000) analyzed the epoxysilane SAMs’ surface morphology and microstructure properties using scanning probe microscopy (SPM) and ellipsometry on single-crystal silicon wafers. SAMs have been used to improve the adhesion bonding of aluminum or plastics but no characteristic data have been presented yet (Saleema et al., 2012; Telegdi, 2007; Wang, Xu, Luo, Wang, & Wang, 2009). Recently, Reis et al.(Reis et al., 2006) have studied SAM of alkane diphosphonate (Gardobond X4661) on Al 5052 alloy samples by EIS in a naturally aerated sodium sulfate solution."

Jan 1, 2016

By Mohamed Sassi, I. Kolo, R. L. Sousa, R. K. Abu Al-Rub, Manhal Sirat

"Fractures induced by folds are pivotal in hydrocarbon exploration, ground water transport and harnessing of geothermal energy. This is because of the need to predict and understand fracture propagation in reservoirs which have folded rock formations. Despite its prominence, there is a lack of reliable numerical models for simulating fractures resulting from rock folding. This is partially due to the difficulty involved in fracture modelling. As a contribution to fold-fracture modelling, this work applies a coupled plasticity-damage model to rock fracturing and anticlinal folds. Parametric studies on a single folded layer give insight into the fold formation and behaviour. The anisotropic continuum damage model which considers both tension and compression is formulated using the power damage evolution law. For ease in formulation, strain equivalence hypothesis is adopted whereby the strain is the same for both damaged and undamaged configurations. Lubliner plasticity yield criterion is adopted for plastic deformation. The model is coded in Abaqus user subroutine UMAT and is applicable to quasi-brittle materials.INTRODUCTIONThe understanding of fractures in the earth’s crust helps in the prediction, evaluation and characterization of fractured reservoirs, whether they are petroleum, geothermal or underground water reservoirs. This is partly because reservoir permeability and stability are dependent on fracture properties (Nelson, 2001). To achieve this, various approaches have been developed to analyze reservoir rock fractures. These could be grouped into (a) discrete approaches – where the rock mass is represented by a finite number of well-defined components and (b) continuum approaches – where the mathematical assumption of an infinitesimal element is made (Jing, 2003). Ivanova (Ivanova, 1998) comprehensively studied fracture systems in nature and highlighted folds as one of the major geologic settings that produce fractures. Naturally occurring folds in reservoirs sometimes compound fracture analysis. It might not be clear whether the fractures formed before, during or after rock folding. Fractures formed during the folding process are expected to show stress orientations related to folding and are thus of primary concern in rock folding simulation. It could be argued that there are no numerical models that as"

Jan 1, 2015

By Zhang. L.

Ordered intermetallic PtSb had been synthesized by arc-melted and then sintering treatment. The electro-oxidation of formic acid on PtSb was investigated at room temperature by cyclic voltammetry and chronoamperometry. The results are compared to those at a polycrystalline platinum electrode surface. It was found that PtSb intermetallic was catalytically more active than pure platinum according to the onset potential and current density. XRD and XPS technologies had been used to investigate the crystal structure and electron effect. We think formic acid decomposition on PtSb favors the reactive intermediate route and is not very much affected by the CO intermediate as compared to Pt.

Jan 1, 2005

By S. D. Normani

A Deep Geologic Repository (DGR) for Low and Intermediate Level radioactive waste has been proposed by Ontario Power Generation for the Bruce Nuclear site in Ontario, Canada. The DGR is to be constructed at a depth of about 680m below ground surface within the argillaceous Ordovician limestone of the Cobourg Formation. The objective of this paper is to apply paleoclimate boundary conditions to a regional-scale groundwater flow model for the DGR site and to describe the influence of glacial loading and unloading on flow system evolution using the FRAC3DVS-OPG flow and transport model. The regional-scale domain encompasses an area of 18,775km2 extending from Lake Huron to Georgian Bay in southwestern Ontario, Canada. From a hydrogeologic perspective, the domain can be subdivided into a shallow zone, an intermediate zone, and a deep zone comprised of the low-permeability units of Ordovician and the more permeable Cambrian where present. The deep groundwater zone is characterized by units containing stagnant water having high concentrations of total dissolved solids (TDS) that can exceed 300g=L. The high TDS values at depth require density-dependent coupled flow and transport calculations within FRAC3DVS-OPG. The computational sequence involves the calculation of steady-state density independent flow that is used as the initial condition for the determination of pseudo-equilibrium for a density-dependent flow system that has an initial TDS distribution. The 1,000,000 year pseudo-equilibrium heads and brine concentrations are used as the initial condition for the paleoclimate simulations. Over the past 900,000 years, the Canadian Shield has experienced approximately nine episodes of complete glaciation. During the glaciation cycles, the entire Canadian land mass has been covered by a series of continental ice-sheets whose maximum thickness reached 4 km and whose southern extents reached, in some cases, beyond the present-day Canada-U.S. border. The glaciation phase of a single glaciation-deglaciation episode is typically 90,000 years in duration, while the deglaciation portion proceeds relatively rapidly and has an average duration of approximately 10,000 years. Output from the University of Toronto Glacial Systems Model, a continental scale North American glacial reconstruction of the most recent 120,000 year glaciation event developed by W. R. Peltier, is used to supply the paleoclimate boundary conditions used in this paper. Permeabilty reductions due to the presence of permafrost are also considered in the paleoclimate simulations. This paper will demonstrate that the choice of rock properties can significantly affect residual pore water pressures within the rock matrix, as well as the migration of glacial meltwater.

May 1, 2009