Search Documents

By Adrian E. Scheidegger

"AbstractThe possibilities of deriving pertinent information about fractures in an oil pay from data obtained by core analysis are investigated. It is shown that it is possible to obtain an estimate of the fractured area per unit volume of the pay, and that the size of the fractures can be estimated if their shape is known. A suggestion of a routine procedure for the analysis of fractures is given.1.-IntroductionMany oil fields are producing essentially from cracks or fractures. Where this is the case, it is important to be able to obtain a knowledge of the size and distribution of those fractures in the oil pay. This knowledge has to be derived from the analysis of cores taken from the fields, as it is generally impossible to follow a fracture through the pay by direct means. The necessity of using statistical methods to extrapolate the meagre information obtained from the cores of the wells is therefore indicated.It is known that the fractures are much bigger than the diameter of the cores; thus, if they strike a core, the latter will generally fall into two pieces. The angle of the fracture with the vertical can be measured and, if oriented cores are taken, the exact position of the surface element representing the intersection of the fracture with the drill stem can be determined. Sometimes the edge of a fracture can be seen in a core. The number of •Cores that show such an edge can be noted. Of course, one has to be careful to distinguish between original fractures in the pay and fractures in the core caused by drilling operations. Only the former are relevant."

Jan 1, 1955

By Pedram Sahba

In today?s emerging economy, pooling resources is a growing trend to reduce overall system costs. Two important resources of every maintenance department are repair shops and spare parts. In this work, we consider a system consisting of mine drills at multiple areas in a mine. In each area, a number of identical drills are operational. When a failure occurs, the defective component should be repaired in a designated repair shop. The failed component can be replaced immediately if a spare part is available. Otherwise, the drill is down until a component is repaired and put back into service. In this paper, the effect of pooling resources is examined, and the conditions under which it is beneficial to pool the resources are investigated. In addition, determining the optimal number of stand-by units, equipment or spare parts, in each case is of interest.

May 1, 2013

By S. C. Ells

Within the Dominion of Canada occurrences of petro-liferous shales have been known for many years. Nevertheless, with the exception of a comparatively brief period, Canada has had to depend largely on foreign sources for its supplies of crude petroleum and petroleum products. Attempts were made to retort local shales in 1859, near Collingwood, Ontario, and again in 1862, near Baltimore, New Brunswick. In each instance these attempts were abandoned owing to the rapidly increasing production of well petroleum from the newly discovered pools of western Ontario and Pennsylvania. Now, after a lapse of nearly sixty years, attention is again directed to the commercial value of Canadian shales as a possible source of crude petroleum. Province of Nova Scotia: The principal deposits of oil-shales occur in Pictou and Antigonish counties and have been known for more than 60 years. During the three years following its discovery, several thousand tons of a particularly rich sub-variety, known as stellarite (stellar coal or oil coal) was mined near Stellarton in Pictou county. It is stated that stellarite yielded upwards of 10,000 cubic feet of 36 candle gas, and that selected samples gave a yield equivalent to 170 Imperial gallons (204 U.S. gallons) of crude petroleum per ton. The average petroleum content of a cargo shipped to Boston was 48 Imperial gallons (57.6 U. S. gallons) and the associated shale or 'bat', gave a yield of 39 Imperial gallons (46.8 U.S. gallons). Part of the above output was shipped to retorting works in Boston and in Portland, and part was mixed with bituminous coals for the enrichment of illuminating gas. Following the discovery of well petroleum in Ontario and in the United States, the mining of stellarite ceased.

Jan 1, 1925

By Charles Goodeve

"BEFORE I begin, I should like to thank The Canadian Institute of Mining and Metallurgy for the honour they have bestowed in inviting me to give this address at the fourth annual C.I.M. Conference of Metallurgists banquet.Secondly, I should like' to convey the greetings of the Iron and Steel Institute of Great Britain in accordance with a request made by its Council at its last meeting. The I.S.I. hopes for the continued growth in strength of this annual Conference and in the collaboration between our respective societies.When I read the program of this Conference, it was brought home to me what a non-ferrons country Canada is. Also, I realized what enormous advances have been, and are being made, and what an ex-citing field non-ferrous metallurgy is for the scientist. This made me wonder, as I have done before, whether the future for steel was proof against these advances.At present, iron and steel stand astride the metallurgical world like a Colossus; I hope that the bronze industry will pardon my stealing their thunder and mixing my metaphors! Will this still be so in the future?The best way to answer this question is to take a look at the fundamentals to see why the iron atom dominates to such an extent that al! other metals are called ""non-ferrons."" Is its present position due to historical and therefore ephemeral reasons, or is there a fundamental difference between the atom of iron and those of other metals?"

Jan 1, 1966

By J. M. Rios

Without conscious effort and understanding, a number of factors peculiar to mineral exploration campaigns conspire against building sustainability in host communities. These include the episodic and transitory presence of an exploration team in the community and the inherent uncertainty of outcomes; most projects fail. Given these circumstances, there is a strong tendency to apply a simple formula of providing employment, pragmatic philanthropy and supporting infrastructure improvements (roads, schools and clinics) to demonstrate that mining provides benefits. Experience in rural native communities of Mesoamerica has shown that it is possible to create positive, sustainable outcomes quite rapidly within communities, which build capacity, improve quality of life and support a strong social license to operate. Success comes from an understanding of community structure and dynamics; engaging with all segments of the community; creating healthy, transparent and accountable relationships based on clearly defined roles and responsibilities; and supporting and strengthening the role of women in a culturally appropriate way. To this are added innovative and culturally appropriate ways of incorporating sustainability through genuine social investment in areas more typically addressed by exploration companies; health, education, and environmental management.

Aug 1, 2013

By Gonzalo Díaz, Diego Mesa, Willy Kracht

"It is well known that frothers affect the amount of water that is transferred to the froth, which has an effect on both the froth stability and the water recovery. On the other hand, since non-selective recovery by entrainment is directly related to water recovery, it can be said that frothers have an indirect effect on flotation selectivity. Recent research on this subject has shown that the non-selective recovery by entrainment, which is characterized by the entrainment factor, is frother dependent. In other words, the entrainment factor is not unique, but depends on frother type.Having different entrainment factors implies that for the same water recovery, the amount of undesired particles reporting to the concentrate may vary if one changes the frother type, which suggests, as a possible explanation, that it is not only the amount of water in the froth what is affected by frother type, but also the froth structure.The purpose of the current work is to study the effect of frother type on foam structure (two phase froth). A quasi-2D cell operated with a slot sparger was used to study the foam structure in the presence of three different frothers: Methyl Isobutyl Carbinol (MIBC), OrePrep®549, and Octanol at the same gas flow rate and reagent dosage. The foam structure was studied using image analysis, and an algorithm based on textural analysis was developed to classify the foams. The results show that it is possible to classify foams according to the frother used, which proves that frothers have an effect on the foam structure.INTRODUCTIONFrothers are usually dosed paying attention to froth stability, condition that is commonly estimated by sight, according to the operator's criteria and experience. This happens because there is not an established procedure or technique for frother characterization, generating qualitative descriptions such as “powerful” or “selective” frothers, which lack of scientific thoroughness and remain under subjective factors. Nevertheless, several works have been done in this line of research. Moyo et al. (2007) classified frothers based on their water-carrying capacity, proving that this characteristic is related with gas holdup and frother type. Previously, Trahar (1981) had related water recovery and gangue particles recovery, defining the entrainment value (ENT). Nowadays it is known that entrainment affects both hydrophilic and hydrophobic because it is not a selective process. In the last decade some studies (for example the one of Konopacka and Drzymala (2010)) delved into different entrainment behaviours dependent mainly on the flotation type (batch or continuous, agitated or columnar, etc.), but there were no studies on the effect of frother type regarding entrainment, since Rahal et al. (2001) argued that the ENT factor was independent of the frother type and concentration, and froth height."

Jan 1, 2016

By D. S. Conochie

The world is poised for rapid growth in consumption as large, less developed economies acquire greater wealth. It might be expected that there would be a corresponding growth in waste generation, but this might not necessarily be the case. The metallurgical industry has an excellent record of process development which has allowed it to provide a high tonnage supply of low cost, high quality metals. Environmental challenges have been faced and indeed the recycling of scrap iron through the electric arc furnace has made a massive contribution to cleaning up obsolete structures and equipment of past generations. Issues in waste generation and processing still remain, and the expectation for cleaner processing and environmental performance continues to rise. The waste impact of key process developments of the last century and the recent developments in metallurgical waste processing in Canada will be outlined. The potential to use state of the art design tools to produce the next generation of zero waste processes will then be explored.

Jan 1, 2004

By Shuan-cheng Gu

Roof bed separation often occurred due to the deformation incoordination of surrounding rock following the excavation of mine roadway. Bed separation has effect on the bolts, and the estimation of the influence will directly affect the safety of support systems. In this paper, the hyperbolic function model to analyze the load transfer mechanism on the bolts was simplified as the exponential function form for easy calculation. An elastic-plastic analysis model of the bolt loading occurred by the bed separation was established. And the development low that the bed separation affected to the bolt loading was discussed. According to the parameters analysis of different separation values and locations, the influence law of the bolt loading caused by roof bed separation was summarized. Finally, the effects of bed separation were considered for the bolting design, it was able to provide a reference to the anchorage design of stratified rock.

Aug 1, 2013

By Roméo Roussin

"The yearly production from the Asbestos Hill pit is 1,550,000 tons of asbestos ore, with a yield varying between 18 and 20 % . The orebody was exposed at the top of a hill, and initial production started without having to remove any overburden. The projected ratio of barren rock to ore, based on the present orebody, was 2 to 1. However, as it was necessary to push back the upper benches, this ratio has changed to 3 to 1. The final pit will be 2,300 feet long by 1,000 feet at the longest and widest points. The final depth will be 680 ft. A pit slope stability study was carried out and an average wall angle of 60-70 degrees must be maintained. Preshearing of final pit limits will produce good wall stability. Permanent access ramps will be 60 ft wide, with an 8 % maximum grade. Geological conditions and the low rock temperature are the major causes of the operation's drilling and blasting problems."

Jan 1, 1976

Operating and Social Considerations from a Contractor?s Perspective

May 1, 2013

By Douglas R. Schmitt

In general, knowledge of the state of stress within the Antarctic lithosphere remains largely unconstrained due in part to Antarctica?s inaccessibility and because of the paucity of seismic focal mechanism solutions. As such, an important component of the ANDRILL project was to acquire new information on the stress directions and magnitudes within the upper crust. Extensive fracture mapping of the core and oriented ultrasonic televiewer logging were carried out to provide strong constraints on both stress orientations and the faulting regime. The first hydraulic fracturing stress determinations in Antarctica were also carried out to provide complimentary stress magnitudes. These measurements were accomplished using a wire-line transported hydraulic fracturing system consisting, essentially, of two synthetic polymer packers that were inflated to isolate the 1-m long pressurization interval. The tests were conducted at the end of the drilling and logging in a ~130-m section specially drilled below 1000 mbsf (nearly 1500 m from the rig floor) for hydraulic fractures. This zone was drilled primarily through competent, dense, and low permeability diamicts. The core fracture and televiewer logging information was used to site twenty separate measurements. Classic hydraulic fracturing pressurization records with unambiguous breakdown and fracture closure pressures were obtained in about half of the measurements. The remaining tests provided fracture propagation and closure pressures that are consistent with the classic breakdown curves, but they did not include a clear breakdown pressure and are indicative of the reopening of either natural or drilling induced fractures in the wellbore wall. The preliminary analysis of the results are in generally good agreement with the stress directions indicated by the core fracture logging and the stress regime suggested by the character of the drilling induced core fractures.

Jun 1, 2012

By M. A. Clayton, D. Kinakin

The Mitchell Creek Landslide is a large, structurally controlled, complex bedrock instability located in northwestern British Columbia. Characterization of the landslide using aerial photograph, exploration geology, and geotechnical investigation data has been completed allowing the development of a three dimensional conceptual model of the landslide domains and slope behaviour. Three domains have been identified in the landslide, from top to bottom: the Sliding domain, a relatively intact slab slowly sliding into the valley; the Transition domain, located in the mid slope of the landslide and showing evidence of significant extension and continuing to subside and displace into the valley; and a Toppling domain, at the toe of the landslide in an area of overturned foliation. Movement is greatest in the Toppling domain, with long term estimated rates of movement up to 4 times that of the Sliding domain; the Transition domain exhibits the greatest range of displacement rates, with average long term values approximately double the slower Sliding domain. This paper documents the results of numerical modelling of the Mitchell Creek Landslide with variation in geomechanical properties, basal rupture surface configuration, structural fabric, and pore water pressure conditions. The locations of internal shear surfaces within the landslide have been estimated from surface scarps, structural fabric orientation, and borehole monitoring data. The performance of each numerical model was evaluated against observed behaviour of the landslide. The configuration and properties of the basal rupture surface were identified as critical to model behaviour, as was spacing and location of internal structures.

Jan 1, 2015

By N. Schreithofer

The deposition of octadecylamine (ODA) at the KCI crystal/NaCI-KCI brine interface was investigated using atomic force microscopy (AFM). The AFM images of freshly cleaved KCI specimens immersed in KCI-NaCI saturated brine at room temperature reveal disappearance with time of the atomic steps and formation of cubic NaC1 crystals. These crystals were found to form when the specimen was withdrawn from the saturated solution. Depending on the way of contacting the specimens with the octadecylamine dispersion, the AFM images show huge differences in the deposition patterns of ODA on KCI crystals. Adequate dispersion was found to help the formation of quite even ODA coverage. The coverage was several monolayers thicker when air/brine/solid contact took place, suggesting that in the potash flotation the collector is likely to be carried to the solid surfaces by air bubbles. The presence of methyl-isobutyl carbinol (M IBC) enhanced the dispersion of ODA in brine, thus helping the spreading of the surfactant on the KCI crystal surface.

Jan 1, 2006

By C. S. Parsons

Introductory The steady advance in the price of lead and zinc in the metal markets of the world during the past few years has resulted in an active search for new deposits of these metals, and to the re-examination of known properties that are now idle. There are a number of deposits of these metals in eastern Canada, the best known of which are the Tetreault mine at Notre Dame des Anges, Que.; the Reader mine on Calumet island, Que.; the Stirling property in Cape Breton, and the Federal mine in Gaspe district, Que. . The author has run concentration tests on the ores from the first three mentioned properties. The ores from Notre Dame des Anges and Calumet island presented problems in concentration which were not successfully solved until the past year. Although considerable experimental work has been done by the Ore Testing Laboratories on the ore from the Stirling mine we have not been successful in developing a satisfactory method of treatment. Character and Types of Ores Metallurgically the lead-zinc ores of eastern Canada may be classified into three distinct types as follows: First: - Ore in which the sulphide minerals are fairly coarsely crystalline and can be freed by crushing to 40 or 60 mesh. The zinc blend has a high iron content (not marmatite) and gives a dark brown colour on grinding. The ores of Notre Dame des Anges and Calumet island, Que., may be cited as examples.

Jan 1, 1925

By P. C. Lighthall, D. W. Zandee, W. Shukin

"IntroductionThis chapter deals with the on land disposal and storage of fine tailing in slurry form behind dams. Other types of tailing, such as coarse dry cobbs from magnetic separation of iron ores and other dry materials, have special problems and are not addressed in this paper. The disposal of mine waste is not included, except as such materials may be of value in the construction activities related to tailing disposal.In earlier North American mining, mines were smaller and frequently disposed of their tailing by direct discharge into neighbouring streams or bodies of water. Where that was not practical or not permitted, the solids were collected in tailing ponds and only the effluent liquids were released or decanted. The dams used for these early impoundments were fragile structures and failures were common. With the advent of large, low-grade open pit mines, and increasing awareness of environmental and safety considerations, recently established mines have carefully-designed tailing disposal systems, with wellconstructed dams and attention given to protection of the environment. Older mines are being improved or at least being examined critically with a view to upgrading as necessary to meet the new standards.Modern tailing disposal systems are highly variable and unique to each mine. Tailing pond selection and design is dependent on available topography as also is the design of transport and water reclaim systems. Suitable sites that are at higher elevations than the mills or distant from them may require that the tailings be pumped. Dams, either earth or rock structures built of the most convenient and economic material, are usually a suitable mix of local borrow, mine waste and coarse tailings. The most economic structures are those built mostly of coarse tailing."

Jan 1, 1989

By Akihiko Nishiyama

Unmanned construction technology used for remote control operation of construction machines has some problems to solve compared with manned operation of construction machines, such as fatigue due to long-term operation or decreases in operational efficiency. To solve these problems, we recorded the viewpoints of operators in both manned and remote control operation and analyzed the differences. This paper reports on our discussion of improving the operability of remote control operation based on the analysis results.

Aug 1, 2013

By Denis Beaudoin

Program Basics: Goals, Course Content & Training Process Sudbury: History of the Program & Lessons Learned Diavik: History of the Program & Lessons Learned Most Recent Program: Totten Mine in partnership with Sagamok Anishnabek Summary -Lessons Learned Conclusion

Oct 1, 2010

By D. Stone, N. J. Aslin, W. Webb

In today's modem copper electro-refineries, increasingly higher average current densities are being employed. With these increases many refineries are approaching their limiting current density. The nearness of the average operating current density to the limiting current density has placed increasing emphasis on the need to maintain an even current distribution. This paper explores the importance of maintaining even current density and discusses the factors, processes and practices that are necessary to achieve and maintain high quality production at high operational intensity.

Jan 1, 2005

By G. A. Moruzi

Two sulphide dust secondacy explosions have occurred in the mines of the SUdbury operations of Falconbridge Ltd. during the past 18 months. 'Ihe main similarity between the occurrences is that they both happened in vertical crater retreat blasthole stopes. A relatively high p:,v.tier factor was noted in both instances. other details are enumerated and examined, as well as some results of tests done by Noranda Research on company ore samples.

May 11, 1988

By Shuji Owada

Scrap electrical and electronic appliances, so called "E-waste", are not a present target to be collected and recycled under Japanese regulations. This material, however, contains considerable amounts of base, precious, and rare metals and it is necessary to recover these elements for maintaining stable supply and establishing "the society of environmentally-sound material-cycle". This paper describes recent trends of rare metals recycling in Japan and technological approaches to achieve the above objective. Also a research work to concentrate rare metals from the printed wiring boards by combining brand new comminution and physical separation methods is discussed.

Jan 1, 2011