Search Documents

By T. Sakai

Present authors have succeeded in single pass large draught rolling of AZ31 and ZK60A magnesium alloy sheets below 200 °C without heating rolls by raising rolling speed above 1000 m/min. Heavy reduction larger than 60% can be applied by single pass high speed rolling even at room temperature. The rolled sheets showed fine recrystallized microstructure by dynamic recrystallization. The improvement of workability at lower rolling temperature is due to temperature rise by plastic working. In high speed rolling, almost all of the work done by plastic deformation is converted into the heat that raises the temperature of the sheet during rolling because the heat did not flow out of the sheet by conduction and radiation within very short time.

Jan 1, 2006

By A. S. Nortjé

At South Deep Gold Mine longhole stopes are backfilled using a cemented Cyclone Classified Tailings in its hydraulic state. The need to contain the hydraulic fill until cured requires a barricade. Due to the massive size of the stopes, the tailings can exert enormous forces on any such barricade. Barricades have long been in use, but recent failures in Australia and the large rate of filling required at South Deep solicited a robust design. A robust design must examine all foreseeable failures and the barricade must be able to resist all expected and, within limits, unexpected loads. The design should also be simple to construct and cost effective, limiting the impact of construction errors and unnecessary delays to production.

May 1, 2007

By W. A. Bain

"AbstractProduction from the Excelsior Reservoir has amounted to approximately one million barrels. This production has caused a 'Pressure •drop of 10 p.s.i. from the original pressure of 1,245 p.s.i.g. Volumetric balance calculations indicate that the pool as being produced by a water drive whose strength is •probably unsurpassed in Western Canada. It has also been shown by 'unsteady state' calculations that the reservoir will still be above the saturation pressure of 915 p.s.i.g. at the time of depletion. The average permeability of the producing formation is approximately 1,000 millidarcys and, consequently, well draw-downs are very low. The field is essentially a bottom-water drive and calculations have shown that gravity drainage will greatly assist the recovery of oil. Water flooding data on several cores •have placed the flushing efficiency at •approximately 50 per cent, which indicates a recoverable oil-in-place of 17.7 million stock tank barrels. Calculations and field data indicate that the MER for the early life of this field is probably as high as 8,000 to 10,000 stock tank barrels per day.IntroductionTHE EXCELSIOR NISKU oil reservoir is located about twenty miles northeast of Edmonton. The field was discovered in November, 1949, by Imperial Excelsior N.o.1 well, in Lsd. 13, Sec. 3, Twp. 56, R. 22, W. 4, at a depth of 3,850 feet.Since discovery, development has continued on a 40~acre spacing pattern. At the end of 1951, drilling over approximately 80 per cent of the estimated productive area of 1,680 acres had established 32 we1ls capable •of production. The field •has been fairly well delineated by dry holes on all but the eastern flank ."

Jan 1, 1952

By C. A. Pickles, K. Mackowiak

Black Thor chromite ore from the Ring of Fire deposit in Northern Ontario was carbothermically reduced in a microwave system to produce a ferrochromium alloy. The as-received ore contained 43.0% Cr2O3, 19.9% Fe2O3, 14.5% MgO, 13.4% Al2O3, and 7.0% SiO2. Activated charcoal was utilized as the reducing agent. Firstly, TGA/DTA and permittivity studies were carried out in order to determine the relationship between the reduction process and the microwave susceptibility. Secondly, microwave reduction experiments were performed on the chromite ore. The variables investigated were; the amount of carbon, processing time, input power and type of atmosphere. A maximum chromium grade of 76.1% and a chromium metallization of 82.7% were obtained for a processing time of 20 minutes, a power input of 800 W, and a carbon addition of 15% in an argon atmosphere.

Jan 1, 2017

This work illustrates the potential of two welding processes for joining AA1100-16 vol.% B4C metal matrix composite: laser welding process using a 4 kW Nd:YAG laser and Friction Stir Welding. A comparison is made between these two welding techniques in terms of microstructure and mechanical properties of welded joints. A large amount of brittle needle-like phases, together with some residues of B4C particles were observed in the fusion zone of laser welded joints. The use of Ti filler can improve the microstructure and increase the joint efficiency from 63% to 75%. On the other hand, the friction stir welding process being a solid state welding technique is interesting as it avoids the formation of brittle intermetallic phases. In addition, the breakage of B4C particles and the grain refinement of the matrix were observed in the weld zone. Consequently, FSW joints show much better mechanical properties than laser welded joints. Up to 100% joint efficiency can be achieved by FSW for annealed AA1100-16 vol.% B4C materials.

Jan 1, 2011

By A. E. Aho

"The Pacific Nickel property lies 7 miles northwest of Hope and 100 miles east of Vancouver, in the Coast Mountains of southwestern British Columbia. Nickel-copper sulphides were discovered in ultrabasic rocks on this property in 1923 and the deposits were explored by Pacific Nickel Mines until 1937, then again between 1951 and 1954 by Pacific Nickel Mines and by Newmont Mining Corporation through its subsidiary,Canadian Ore DepositsWestern Nickel. The property was studied by C. E. Cairnes (1) in 1924, by W. E. Cockfield and J. F. Walker (2) in 1933, by H. C. Horwood (3), (4) in 1936 and 1937, and by the writer in 1951 and 1952. Except for a few thousand tons for trial shipments, the property has never been mined. Indicated ore reserves now total somewhat over one million tons averaging about 1.4 per cent nickel and 0.5 per cent copper, with lesser values in precious metals and cobalt.GEOLOGIC SETTINGThe nickeliferous ultrabasic rocks form part of the core of a 15-milewide block of Late Palæozoic metamorphic rocks and Mesozoic intrusives which extend north-south between the coast batholith of British Columbia and the Chelan batholith of Washington. Margins of this block are faulted in part against less metamorphosed volcanic and sedimentary rocks largely of Jurassic and Lower Cretaceous age (Geo/. Surv., Canada, Map 737 A, 1942). Serpentinites, suggestive of deep transgressive structure, occur within the block, and also at its east margin along faults which are southern extensions of the regional Yalakom-Fraser River fault zone. Some of the other mineral deposits in the Hope area appear to be spatially related to these major faults.The mineralization at Pacific Nickel occurs almost exclusively within a stock-like mass of ultra basic rocks which mingle with, and partly cut, a larger batholithic mass of genetically related diorites and norites of late Mesozoic age (Figure 1 ). The ultra basic mass consists essentially of fresh, medium-grained hornblendic pyroxenite with peridotitic cores and with a remarkable margin of pegmatitic hornblendite. The most hornblendic rocks appear to be chiefly products of reaction and replacement of the pyroxene and olivine rocks. The mineralization consists of disseminated and massive pyrrhotite, with subordinate pentlandite and chalcopyrite, amongst fresh olivine, bronzite, and, Jess commonly, augite and hornblende. Both the ultrabasics and mineralization are cut by small hornblenditic and dioritic dykes, and by veins and alteration zones."

Jan 1, 1949

By P. Cleyle, J. H. Masliyah, R. S. Chow, Z. H. Xu, Z. A. Zhou

Bubble nucleation in water under dynamic conditions was investigated using an autoclave at an air saturation pressure of 7 atm. Agitation during air saturation of water was found to be crucial in enhancing tiny bubble formation. More bubbles nucleated on hydrophobic surfaces at a higher agitation rate, due to cavity formation by the more intense hydrodynamic conditions. Flotation recovery of bitumen from oil sands demonstrated a significant role of bubbles nucleated in water: more than 50-170% increase in bitumen recovery from different oil sands was obtained by using air supersaturated than the regular water.

Jan 1, 2009

By Maria D. Mastalerz, Wei Wang, Maria E. Holuszko, Amit Kumar

In this study, the micro-FTIR analysis was used to investigate in-situ surface properties of coal and its components (macerals) and these were directly correlated to the coal hydrophobicity as measured by the contact angle before and after reagent addition to understand the suitability of the reagent for flotation. The micro-FTIR technique can provide a semi-quantitative analysis of the chemical functional groups on coal surface, exactly where the contact angle is being measured. Selected functional groups and their ratios that provide information about aromaticity, the contribution of oxygenated groups, and aliphaticity are used to evaluate the reactivity between reagents and various coal components. The observations made in relation to the susceptibility of some reagents towards certain coal components should lead the way to a smarter way of using process design in terms of reagents selection for coal flotation.

Jan 1, 2017

By S. Hopkins, R. Preston, S. Gillis

"This paper examines typical visual inspections of operational soft rock mine shafts and discusses some of the challenges involved, many of which are associated with inconsistent inspection practices. The paper presents the development of a more standardized approach to periodic shaft inspections that supplement the more frequent inspections performed by shaft crews at the mine. This approach helps to keep an accurate record of changing conditions, compare conditions between multiple mine sites, as well as prioritize and plan potential remedial work. INTRODUCTION Shaft inspections, whether they are performed daily or weekly by members of the shaft crew at the mine, or periodically by consultants, traditionally involve a visual inspection undertaken with personnel traveling on an inspection deck on the conveyance, taking notes and photos. Inspections are typically required by mining regulations and carried out to identify and address hazards before a safety incident occurs that could cause harm to people or damage to property, as well as to help plan required maintenance work. Depending on the site, there can be many challenges associated with inspections in the shaft, especially compared to a typical inspection at surface. Some of these challenges are associated with the shaft environment itself, while others are related to the subjectivity of inspections and a lack of standardization, particularly between multiple sites within the same operating company. Recognizing these challenges, a more consistent and repeatable approach to shaft inspections in soft rock mines is evolving. This approach involves reviewing available historical data, comparing sites with similar conditions, establishing survey control, documenting observations and measurements with locations, and updating as-built or condition drawings. Part of this standardized approach is the implementation of an innovative 360-degree camera with a high-power lighting system that can be used either remotely or alongside personnel completing a traditional visual inspection. The system uses six cameras to take photos at a rate of 15 frames per second, with the image data subsequently processed and stitched, then joined into a high-resolution video. This tool improves time-efficiency, objectivity, and repeatability of inspections."

Jan 1, 2019

By Jack F. McQuat, Ross D. Lawrence

"Most geologists and mining engineers, in the course of their professional careers, frequently become involved with the appraisal of metalliferous mineral deposits and develop a familiarity with and standard approach to the evaluation of these deposits. When the same individuals approach the industrial mineral field, however, their usual approach pattern can be rudely disturbed.This paper highlights the difference in appraisal approach and outlines the factors common to both but which have entirely different emphasis. These comprise geological appraisal, analytical requirements, the importance of transportation, marketing requirements and standards, including appropriate allowances for product development, and marketing penetration.Out of these ""different"" considerations, however, a pat-tern or standard approach emerges which is as common to the industrial mineral field as that used either consciously or subconsciously in the metallic field.The paper reviews the different factors and points of emphasis and offers an outline of the common pattern of appraisal for industrial minerals."

Jan 1, 1971

By C S. Beals

The Dominion Observatory was founded in 1905 and, from the beginning, it work included research in both astronomical and geophysical science. During its first years, up to 1916, the Observatory also included geodetic surveying as part of it scientific program. Although, at the beginning of the century, geophysics did not have the close connection with mineral exploration that it now holds , the founders of the Observatory were men of vision, and they laid a solid foundation for the application of the techniques of geomagnetism, gravity and seismology to an understanding of the Canadian terrain of plain , mountains, seacoasts and shield area . The particular sphere which the Observatory occupies in the field of geophysics has been evolving over a period of many years and it has now a rather definite relation to the work of other government bodies, university science departments and industrial organizations. We have, for example, an over-all responsibility for the regional magnetic mapping of Canada and, as the magnetic field is subject to slow but steady changes, we produce new magnetic maps of the country every five years. These maps indicate the strength and direction of the magnetic field, the variation of the compass and the rate of change of the magnetic elements.

Jan 1, 1963

By M. El Tokhi, H. Arman, B. M. Amin

"This paper aims to overview some mechanical and physical features of the gabbroic rocks. The study has two phases: filed study/in-situ measurements and laboratory work. During the field studies, rock block samples were collected from different locations of the study area to represent the different types of the gabbroic rocks. Either core or rock samples for various tests were prepared from rock samples taken to the laboratory. The unconfined compressive strength (UCS), indirect tensile strength (ITS), point load index (PLI), Schmidth hammer rebound value (SHV), slake durability index (SDI), sonic velocity (SV) and unit weight (UW) test were carried out either on the selected rock block samples or core samples.INTRODUCTIONThe geology of the United Arab Emirates (UAE) has been divided into three major rock units (Lippard et al., 1986); an autochthonous succession, allochthonous units composed mainly of Mesozoic rocks and include the Sumeini Group (concomittent slope sediments), Hawasina Complex (basinal sediments) and the Semail ophiolite nappe (massive slice of former oceanic crust), that were emplaced as a series of thrust nappe in the Late Cretaceous and Neo-autochthonous sequence of Maastrichtian and Lower Tertiary sediments.The Semail Ophiolite (600 km long and up to 150 km wide) is thought by some authors (Glennie et al., 1990) to have been generated along a subduction related back-arc spreading axis during the Cenomanian-Turonian and was obducted onto the Arabian continental margin during the Campanian. Others, however, consider it to represent a primitive arc-spreading center related to oblique subduction Lippard et al., 1986). The Ophiolitic rocks in the study area comprise mantle and crustal sequences. The mantle peridotite and crustal gabbros are the dominant rock types of the exposed Semail Ophiolite north of the Hatta zone. This paper is only concentrated on the gabbroic rocks."

Jan 1, 2015

By J. E. Quinn, S. Wolstencrof, K. H. Soldenhoff

Ion Exchange (IX) using Strong Base Anion Exchange (SBA) resins is conventionally used to purify uranium from sulfuric acid pregnant leach solutions (PLS), particularly when uranium grades are relatively low. However, the presence of chloride in the PLS interferes negatively with conventional SBA based IX processes, by reducing the uranium loading on the resin. Chloride can be present in the PLS due to the use of saline bore or seawater in leaching, or chloride containing leach/IX reagents. ANSTO has been examining strategies to combat this problem for several years. ANSTO previously reported that a recently developed high-capacity SBA resin was capable of extracting uranium efficiently from saline leach liquors produced at Boss Resources’ Honeymoon in-situ recovery mine in South Australia. The resin was tested successfully in a 2017 Field Leach Trial carried out onsite in the existing wellfield area. While the piloting was extremely promising, the elution was more challenging, with eluate tenors limited to 2 g/L U3O8 using NaCl. This is due to the resin’s strong affinity for the uranium complex, which makes it difficult to elute efficiently by standard methods. In this paper, we describe a novel elution process developed for strong base resins that significantly improves upon conventional methods. The process, developed by ANSTO, is based upon conversion of the extracted uranyl sulfate species to uranyl carbonate, followed by elution with sodium chloride. The loading and elution process was demonstrated in continuous locked-cycle piloting conducted at ANSTO in 2019. The results were excellent, with eluate tenors of 8–9 g/L U3O8 achieved from Honeymoon PLS containing 50 mg/L U3O8, with very little transfer of impurities. In subsequent test work, the eluate was shown to be amenable to uranium peroxide precipitation. The results represent a huge step forward for the purification of uranium from saline leach liquors.

Jan 1, 2020

MR. J. F. MYERS, Consulting J3eneficiation Engineer, Greenwich, Conn.: In the written discussion contributed by Mr. F. C. Bond in item ( 2) (page 515), speaiking about the significance of the ratio of mill diameter to the make-up ball diameter, he states: "When this ratio exceeds 100 the power and capacity of the mill are de-creased"; and the paragraph ends with a reference to the 30 per cent ball volume "with some de-crease in mill capacity". I believe this broad statement is incorrect. When we are dealing with a non-cataracting mill, pre-ceded by a good rod mill, there is a slight increase in capacity, but the power does drop. The second point that I consider needs consideration is Mr. Bond's item (8), Proper Mill Speed (page 516). This paragraph should be qualified to cover single-stage mills only. It does not apply where a rod mill is followed by a non-cataracting ball mill. The statement as is, with no qualification, gives an erroneous idea of proper mill speeds.

Jan 1, 1957

By T. Wajima

"A novel carbonaceous adsorbent for recovery of nickel from nickel plating waste solution was prepared from rice straw using sulfur impregnation. The rice straws were cut to 1 cm pieces, and then immersed in 0.01 - 3 M K2S solution to prepare sulfur-immersed materials. The immersed-materials were heated at 100-700 ºC in nitrogen gas to produce the sulfur-impregnated carbonaceous adsorbent by pyrolysis. The contents of carbon and sulfur in the adsorbent and abilities of adsorbent to recovery nickel from aqueous solution were examined. The contents of carbon and sulfur in sulfur-immersed materials are almost same as those in raw material. In pyrolysis, with increasing the heating temperature to 200 ºC, the contents of carbon and sulfur are almost constant, and then above 300 ºC those increase. The recovery for nickel using raw material, sulfur-immersed material and the product pyrolyzed at 100 - 200 ºC are almost same, and with increasing the heating temperature to 400 ºC, that of the product increases, and above 500 ºC that of the product decreases. In immerse step, with increasing K2S concentration, the carbon content of the product at 400 ºC gradually decreases, the sulfur content of the product increases, and the recovery for nickel using the product gradually increases and then above 1 M K2S decrease. The product prepared from material immersed in 1 M K2S solution at 400 ºC indicates a maximum recovery for nickel ion. The product can adsorb nickel ion in nickel plating waste solution coexisting with phosphate ion, and adsorbed nickel ion in the product was deposited as nickel metal after heating at 1000 ºC under N2 atmosphere.INTRODUCTIONRice is the second world’s largest cereal crop after wheat, but produces large amount of straw residues, of about 330 million metric tonnes. Rice is a widely grown crop in Asia, and rice straw is produced as a by-product of rice production. In most parts of rice fields, open-field burning of rice straw is commonly practiced in the region when there is limited time to prepare a field for the next crop. However, open-field burning of crop residues is an uncontrolled combustion process during which air pollutants are emitted into atmosphere. These air pollutants have significant toxicological properties and are potential carcinogens (Gadede et al., 2009). Although wildfires are prohibited in cultivation fields of most countries, farmers usually keep on burning their crop by-products. Biomass burning is an important source of aerosol particles which may affect local and regional air quality (Gao et al., 2011), and also contribute to global climate changes."

Jan 1, 2016

By J. Font

The RAF or copper fire refining process at the Caletones smelter of CodelcoChile consists of several pyrorefining stages that successively lowers the levels of S, Fe, Pb, As, Sb, Te, Se and to some extent 0 in the copper melt, allowing the production of high quality fire-refined copper of 99.93 % purity (RAF copper). This chemical feature of the RAF copper is only achieved by quite long processing times, and a considerable consumption of fluxes and fuels in the RAF vessels. The main goal of this study was to improve the RAF process performance by thermodynamic considerations and industrial scale tests, i.e., an in situ approach for the process as featured by intensive sampling, characterization and subsequent modifications. Thus, both theoretical and industrial data were derived, and based on kinetic and thermodynamic evaluations, a higher operational standard was achieved for the RAF process. These new operational practices allowed enhancing the overall economic of the RAF process, by reducing the time and operational costs, and consequently increasing the availability of the vessels.

Jan 1, 2007

By D. B. Dreisinger, A. A. Gunaratnam

A pressure oxidation (POX)-hot cure (HC)-lime boil (LB) process is used in industry to recover silver from refractory gold sulfide ores containing minerals such as pyrite and arsenopyrite. Pressure oxidation is used to oxidize minerals and liberate occluded gold particles. As such, iron goes into solution and under acidic and high temperature conditions often precipitates as basic iron sulfate (BFS). BFS consumes excess lime during neutralization prior to cyanidation. Therefore, a hot cure stage is required to re-dissolve BFS back into solution. BFS re-dissolution consumes acid and produces ferric sulfate. In the presence of silver, these conditions favor the slow formation of silver jarosite. Silver jarosite is refractory to cyanidation, and must be broken down prior to cyanidation. This is done in the lime boil to produce a cyanide-soluble silver hydroxide. A study was conducted to investigate parameters that affect the precipitates that form in each stage of the POX-HC-LB process.

Jan 1, 2017

By V. Aprahamian, G. B. Harris, C. W. White, M. Tangen

"In 2005, the Royal Canadian Mint (RCM) commissioned a new silver electrorefining circuit. This circuit was intended to operate with a minimal electrolyte bleed for the control of copper. However, by the time of start-up, the levels of copper-rich silver doré to electrorefining had increased, and despite partial pyro-conversion in a small Top Blown Rotary Converter (TBRC), copper concentration in the silver anode still averaged 7.5%. This necessitated frequent replenishment of the electrolyte with fresh silver nitrate since copper displaced dissolved silver during electrolysis, and therefore requiring a robust copper bleed treatment step in order to maintain cathode silver flake purity at 99.99%. The originally-installed bleed treatment system could not meet the RCM’s needs. A thorough review of known technologies, however, did not indicate one capable of handling the copper load, and resulted, therefore, in the development of a novel copper hydrolysis approach for removal of copper as an insoluble basic nitrate salt, and recovery of the associated nitric acid for re-use in the circuit. Laboratory-scale trials showed reproducible results, and existing equipment was subsequently modified.INTRODUCTIONIn 2005, the introduction of a new silver electrorefining circuit at the Royal Canadian Mint (RCM) initiated changes in the way customer silver, collected from the gold doré circuit, was processed. These circuit changes were discussed in a recent paper (Aprahamian, 2015). A wastewater treatment plant had not been budgeted at the time, and this represented a significant constraint when considering the introduction of a wet processing circuit. After a review of various options, a turnkey silver electrorefining circuit was purchased from a European firm. Initially, enough cells were ordered to produce 2 million oz of fine silver (999), with the option to increase to 5 million oz. The selected equipment was based on a Moebius cell design combined with a silver grain pressure dissolver to produce make-up silver nitrate solution. Additionally, an evaporator/hydrolysis unit included in the package appealed to the Mint Refinery, on the basis that it offered a simple way to bleed dissolved copper in electrolyte without generating effluent."

Jan 1, 2016

By N. Musee, N. Kornelius

This study presents a neural network approach to modelling the liberation of gold bearing ores. A complete mineralogical analysis of unmilled and milled ores, including gold deportment and gangue content are used as inputs to a self-organising neural net which generates order preserving topological maps. The arrangement and shapes of these clusters are coupled to unmilled free gold data to predict gold liberation in milled ores (absolute error: 4.2%). Moreover, the self-organising maps were diagnostic of the quality of data used, indicating that the relationship between particle size and gangue material content requires further investigation.

Jan 1, 2005

By Owen Owens, W. P. Armstrong

Abstract- The process of arriving at the size and grade of: (a) a newly-discovered body of mineralization, (b) a potential ore resource, (c) an orebody proposed for mining, or (d) the ore reserves in a mine, requires fundamental geological, and geometrical determinations as well as physical and chemical analyses. This paper outlines geological and geometrical features considered critical, in the authors' experience, in realistic reserve determination. These are discussed under the headings "The Four Cs". They include the Character, type or nature of the mineralization; the Continuity of various types of mineralization in the deposit; various key concerns in the Calculation besides the mathematics; and the Classification section which refers to basic considerations in classifying a mineral estimate. It is suggested that the responsibility for the calculation of a Resource or Reserve should be that of a geologist experienced in the ore type under review. Further, it should be the responsibility of the board of directors of the company owning the deposit to ensure that a sufficiently experienced person is chosen to carry out the process.

Jan 1, 1993