Search Documents

By C. -G. Berg, J. T. Tuominen

Since the beginning of the 20th century, energy efficiency in copper smelting has been improved by a factor of 30 as a result of adopting autogenous smelting processes with more and more efficient waste heat recovery systems, increasing use of oxygen enrichment and countless smaller improvements. Nevertheless, energy in the form of electricity and fuels continues to be the biggest contributor to smelter operating cost. Metallurgists around the world are under constant pressure to find ways to save those precious megajoules wherever they can. One area that is often neglected is the removal of water contained in concentrates. Copper flotation concentrates, as delivered to a smelter, typically contain some 8–12% moisture. This moisture must be removed and the only way to do this is by evaporation, which consumes a lot of energy. Several studies have shown that the most efficient way of removing this moisture is to use a steam- heated indirect dryer—the least efficient way being the feeding of wet concentrate directly into a smelting furnace. Even in the most efficient smelters that employ modern steam drying, the energy needed to remove the moisture from the concentrates constitutes over 15% of the total energy consumption of a smelter – acid plant complex. The major steps that have been taken in the past to lower the energy consumption of moisture removal are the use of drying in general and the adoption of steam drying. The energy efficiency of concentrate drying has been improved by 25% over the last 20 years. The latest giant leap in this area, the Kumera Heat Recovery Dryer, is the result of Kumera’s long-term development in improving the efficiency of concentrate drying. The Heat Recovery Dryer is a novel application of steam drying that uses the waste heat from dryer exhaust gas for drying concentrates, thus, cutting the energy consumption by a further 30%. This paper discusses energy consumption in copper smelting in general and analyzes the energy consumption of concentrate drying in detail. Different dryer types are compared especially from the perspectives of energy consumption and environmental emissions. Applicability of different energy sources for drying is evaluated and discussed. The principle of the Kumera Heat Recovery Dryer is presented along with results from extensive continuous pilot plant tests. Potential applications and the feasibility of Kumera Heat Recovery Drying technology are discussed.

Jan 1, 2019

"The standards set out requirements of the Toronto Stock Exchange for company’s providing information to investors, regulators and/or the media regarding their mineral properties. In addition, information contained in new releases, continuous disclosure documents [annual report], or other forms of communication [printed investor relations materials and electronic publications] are also subject to these standards.1.0 INTRODUCTIONThe disclosure of the results of exploration and development activity on mineral properties mustcomply with the requirements of the Toronto Stock Exchange Policy Statement on Timely Disclosure, theOntario Securities Act and all applicable policies and rules of the Ontario Securities Commission and anyother securities regulatory body having jurisdiction over an issuer listed on the Exchange. In particular,the requirements of National Instrument 43-101 must be followed.The purpose of the standards is to set out the requirements of the Toronto Stock Exchange when acompany provides information to investors, regulators and/or the media regarding its properties, whethersuch information is contained in a news release, a continuous disclosure document such as an annualreport, or other form of communication, including, but not limited to, printed investor relations material andelectronic publications such as Internet Web sites. These standards do not apply to prospectuses orlisting applications, the standards for which are contained in the policies and rules of the securitiescommissions and the Exchange. These standards are also not intended to establish requirements for thecontent of technical reports.Any information published by or on behalf of a company must comply with these standards. If acompany becomes aware of information published by others regarding its mineral properties which ismaterially misleading to investors, it should take appropriate action to correct such information orotherwise make it known that it is not responsible for publishing such information and does notnecessarily agree with such statements.Disclosure concerning mineral properties should identify the ""qualified person"" as defined in NI 43-101 who is responsible for the work conducted on the property and such person shall have read andapproved of the technical disclosure."

Jan 1, 2003

By I. Colquhoun

Current practice tends towards "integrity as an afterthought". That is, integrity is treated as an isolated aspect of operations and maintenance. In fact, this works quite well. But it would work so much better and with less uncertainty if integrity management measures were introduced at the design phase and addressed the entire life-cycle of the pipeline asset. The talk will address the measures and metrics that can be implemented on a new pipeline during design to optimize integrity and deliver a comprehensive operating manual and integrity management program for the pipeline system. This deliverable should describe the risks to be assessed and monitored, and the actions to be taken to control these risk adequately. Properly executed, integrity by design will provide a good working estimate of the life-cycle integrity management costs and maximize system reliability.

Jan 1, 2005

"THE GOLD MINING REGION of Timmins - Val d'Or, astride the Ontario-Quebec border, has long suffered the effects of rising costs during the period when the U.S. price of gold was fixed at $35 per ounce. The federal government, through such assistance programs as that set up under the Emergency Gold Mining Assistance Act (E.G.M.A. ) in 1948, has subsidized the gold mining communities of Canada for a total of over $300 million to March 31, 1972. Of this, the Timmins - Val d'Or ""gold belt"" has received more than twothirds, almost $220 million. In spite of these continuous subsidies, only 12 gold mines are still producing in the Timmins - Val d'Or belt, whereas 71 mines have received subsidies for some period since 1948. The vital question is how the communities previously supported principally by the mining of gold will survive in the long run, as many of the older mines either are already depleted or are quickly becoming so. With the rising price of gold on the 'free market in recent months, prospects look a little brighter for the time being. Even with the increased official price of U.S. $38, which made the maximum government subsidized price about $48 per ounce, gold mines have not sold any gold to the government since January 1972 and some stopped doing so months before that. The populace of the region has not been enthusiastic about relocation nor about extensive retraining programs in the past and probably will not be in the future. So, when the remaining gold mines become depleted, the old problems of community depression will remain."

Jan 1, 1973

By S. Rash Ahmadi

Welding is highly reliable and efficient metal joining process. In welding the metal adjacent to the weld joint is subjected to severe thermal conditions. As a result, complex changes in metallurgical structure occur in this region. These changes in structure depend on the material and the temperature history experienced. Friction stir welding (FSW) is relatively a new welding process in which, heat is generated by friction between the tool and the workpiece. The amount of heat conducted into the workpiece determines the quality of weld, residual stress and distortion of the workpiece. The objective of the current work is to study the transient temperature in a friction stir welding. So, a three dimensional transient analytical model is used to study the thermal distribution during the welding. Heat input from the tool shoulder alone is considered in the model. The process parameters like axial load, welding speed and tool rotational speed, used in actual FSW process are taken to build the model. This analytical model is very useful for select the optimized affected parameters in friction stir welding. The model illustrates the comprehensive equation including actual affected parameters in FSW and it can be used for different materials. In addition to the above the thermal history finds application in design of welding tools.

Oct 1, 2011

By J. Starkey

A comminution circuit in recent history, is one of the most difficult parts of a mineral processing plant to design with confidence. It is usually the most costly part of a plant to build, and it can consume up to half or more of the energy used on a mine site. To suggest that comminution energy usage is sustainable in the long term is not possible at this time. What we have to choose from today, based on more than 50 years of experience, does include the best available technology, and the best way to design it. There is controversy in the industry as to how to properly approach the subject of comminution design, with many of the optional solutions requiring a level of training and expertise beyond the ability of a non-specialist engineer. Semi-autogenous grinding technology in particular, has not been properly appreciated because of many recent mistakes in its application and design, which have blurred the positive perception about what SAG technology is, how it can be used, and how it needs to be designed and built. In order to change this, mine owners and senior managers need to take responsibility for, and learn to understand the fundamental challenges that a comminution circuit poses to the project, to the design process, to the operators who use the equipment, and to the resulting metallurgy. This address is intended to summarize these challenges and offer fundamental engineering solutions, which are clear, specific and in a format which is directly applicable to the mining and mineral engineering community.

Jan 1, 2018

By S. A. Sadough vanini

In this paper, Stress-Strain-Temperature relations for Shape Memory Alloys are studied. Temperature effects on Shape Memory Alloys are different from those related to ordinary materials. In ordinary materials, elastic characteristics can be assumed to be constant in low temperature ranges, and only the deflection arising from temperature changes could be added to the elastic defection. As long as two phases of austenite and martensite could be present in Shape Memory Alloys simultaneously, elastic modulus follows temperature and temperature gradient. In continue a smart actuator is investigated considering a homogeneous cantilever beam. Beam bending is established by using shape memory wires. An initial strain is imposed to shape memory wires in a low temperature, and then, they are installed in the outer surface of the beam. Therefore, since the temperature is imposed in these wires and they cannot have free recovery strain, the compressive recovery stress will be produced in the outer surface. This will result in a deflection in axial direction of the beam. At first, beam deflection is calculated on the basis of theoretical relations and solving the relevant differential equations. Afterwards, experimental tests are performed on an elastomeric beam equipped with shape memory wires. When a voltage is applied, a temperature rise will occur in the wires; then, this temperature rise causes a deflection in the beam. Finally, the theoretical and experimental results? comparison indicates a good conformity. One capability of this actuator is its high flexibility, and by controlling the inlet current, the end-beam deflection can be controlled.

Oct 1, 2011

By Lawrence Devon Smith

"The concept of risk is well established in the mining industry. It is acknowledged when estimates of reserves are expressed as proven or probable, when mining and metallurgical recoveries are applied to the ore, and when contingencies are added to costs. However, it is difficult to provide a quantitative assessment of risk. The significant sources of risk in a mineral project and how these are addressed in project evaluations are discussed.The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.IntroductionThis paper examines the components of the discounted cash flow discount rate and proposes a method of estimating project-specific discount rates. The motivation for this work comes from experience of project evaluations in which owners and purchasers had agreed on virtually every aspect of the evaluation except how much the project was worth. Agreement was reached on reserves, grade, recovery, capital costs, operating costs, taxes, and, by combining these components, even on the final cash flow values. The only difference in opinion concerned the discount rate to be used in the calculation of the net present value. Depending on the life of the project, such differences of opinion can cause a variation of more than 50% in the value placed on a project! This is illustrated in Figure I."

Jan 1, 1995

By P. S. Daly

"The purpose of this paper is to describe the types of instrumentation used at Sherritt Gordon's Ruttan Mine to monitor the"" effects of mining. The aim of the monitoring program is to establish parameters to achieve a maximum ore recovery with minimum dilut ion in a safe environment.The copper-zinc Ruttan Mine is in northwestern Manitoba, approximately 760 km from Winnipeg (Fig . I) . Production commenced in 1973 from the open pit at the rate of 10,000 tons per day. Pit bottom lies 58 metres above the first mine level. Underground development has overlapped with open-pit mining throughout. The open pit was phased out in the latter part of 1980.Underground production began in early 1979. The mining method employed in the first lift is sub-level blasthole open stoping with delayed hydraulic filling. Large-diameter (6.5-in.) holes are being drilled in the crop stope area and are also planned for some other areas for vertical retreat mining into a slot. GeologyThe orebody consists of numerous sulphide lenses of variable size, geometry and geology . The lenses occur within volcanoclastic host rocks which exhibit a strong variability in intensity and type of alteration and structural characteristics. Stope design and sequencing were based on these complex geological factors."

Jan 1, 1981

By G. Avramovic-Cingara, H. J. McQueen

The microstructure of commercially pure aluminum was investigated by using polarized optical microscopy (POM), orientation imaging microscopy (OIM), and transmission electron microscopy (TEM) techniques. Specimens were deformed in torsion at 400°C and equivalent strain rate of 0.1 s-1, to various strains of 0.2, 0.5, 1, 4, and 6. The results indicate that POM can usefully reveal grain and subgrain structures over a large field in aluminum. TEM is most suitable to study dislocation substructure and evolution of subgrains. While TEM microscopy and OIM are capable of resolving individual subgrains, OIM can not reliably distinguish subgrains with small misorientations, particularly in samples with low strain. On the other hand, the OIM technique is very useful in the analysis of many regions surrounded by high, medium, and low angle boundaries (HAB, MAB, LAB). Various misorientation maps were studied using different data processing methods. The analysis revealed that the subgrain size is relatively insensitive to strain. The fraction of low LAB ( < 5°) decreased and HAB (>15°) increased conversely with increasing strain, whereas MAB (5-15°) remained stable. The development of an increasingly bimodal grain boundary misorientation distribution is consistent with the predominance of dynamic recovery (DRV) in the evolution of microstructure, combined with geometrical dynamic recrystallization (gDRX), now called grain-refining DRV.

Jan 1, 2006

By Denilson Coutinho, Euler Soares, Paulo de Tarso, Jordana Ferreira, John R. Goode, Andreas Sprecher, Alexandre Rocha

The Serra Verde Project is located in the northern part of Goiás state, Brazil, and comprises 49 mineral claims covering an area of 69,814 ha. The Serra Verde deposit is a rare earth element (REE) enriched weathered granite comparable to the weathered granite, or ionic-clay, deposits found in southeastern China. The Mineral Reserves of the Serra Verde Project total 388 Mt (Measured and Indicated) at an average grade of 1,484 ppm of REE oxide (REO). Several hundred agitated leach and column leach tests have confirmed recovery of about 40 to 55% of the REE, except for Ce, using simple desorption techniques. Present plans call for a heap leach operation followed by precipitation of impurities and precipitation of a pure REE carbonate suitable for refining and separation. The project plan includes initial production of 5,000 t/a of REO, with a high content of heavy and critical REO, rising to 10,000 t/a of REO. This production rate will be obtained by mining of the Mineral Reserves over a 22-year mine life at an initial rate of 6 Mt/a for the first four years with the mining rate thereafter increasing as required by grade and production targets.

Jan 1, 2014

By A. Tikhonov, D. Kipper, V. Korovin, A. Olifirenko, Yu. Shestak

The present paper deals with vanadium and molybdenum sorption from industrial wastes and intermediate processing products using Cybber macroporous strong- and weak-base anionites. Vanadium and molybdenum recovery by Cybber anion-exchange resins as well as desorption processes were studied in static and dynamic modes; their efficiency was demonstrated for that purpose. The results of the work may be used to design technologies for complex processing of both ores and industrial wastes containing vanadium and molybdenum.

Jan 1, 2011

By Raj K. Rajamani, Nikhil Dhawan

"Agglomeration has become common pre-treatment step to improve heap leach percolation thereby recovery, the fundamental understanding of the agglomeration process for crushed ores is still lacking. Agglomeration is required for ores which either contain excessive amounts of clay or an excessive quantity of fines generated during mining and crushing. Numerous experiments have been carried out in laboratory scale batch drums using different ores. It has been found out that experimental agglomerate size distributions exhibit self-preserving spectra. The self-preserving/ similarity distribution of the agglomerates is found to be independent of operating conditions and is uniquely determined by the size enlargement mechanism. An empirical model based on the absolute difference between moisture applied and optimum moisture was developed. This model uses self-preserving spectra in the form of a Rosin-Rammler distribution function to predict size distribution at different operating conditions. The empirical model was considerably easier to work with plant scale agglomeration drums. Also, a test known as dip test is developed which improves fundamental understanding of the agglomerate formation and growth mechanisms. This test also provides the progeny size distribution of each agglomerate size. The progeny size distribution was analyzed with a model that partitions the particles into a host and guest category. The ensuing partition coefficient identifies the behaviour of a particle as a host for other particles or a guest layering on other particles. This concept helps in identifying the type of agglomerate that would result for a specific feed size distribution. INTRODUCTIONHeap leaching is one of the hydrometallurgical processes that have served as a green and economically viable process for the treatment of low grade complex ores of copper, uranium, nickel, silver and gold (Dhawan et al., 2013). Heap leaching appears to be a favorable candidate for the least energy consuming process for low grade ores. In heap leach operations nowadays a pretreatment step known as crushed ore agglomeration has been implemented (Dhawan et al., 2013). A bed of agglomerates improves the uniform percolation of solution through the heaps of ore. Therefore, it was possible to treat wastes and mill tailings via agglomeration and heap leaching. Agglomeration pretreatment is required for ores which either contain excessive amounts of clay or an excessive quantity of fines generated during mining and crushing (Bouffard, 2005; Dhawan et al., 2013).While agglomeration has become common practice pretreatment step in heap leach operations, the fundamental understanding of the crushed ore agglomeration process is still lacking. The author reviewed publications up to 2012 on the crushed ore agglomeration process and did not come up with modeling studies on the topic (Dhawan et al., 2013). Some of the possible reasons can be the stochastic nature of the process, experimental difficulties, and lack of instrumentation for fundamental studies."

Jan 1, 2016

By A. W. Jacobs

SHORTLY after Denny, Robson, and Irwin(l) published their first paper, in 1937, on the prevention of silicosis by metallic aluminium, experiments were begun on the practical application of the discovery. It was thought at that time that aluminium powder, to be effective in aluminium therapy, would have to be intimately admixed with siliceous dust at the latter&apos;s source. There followed several years of experimental work underground, during which the application of aluminium powder was tested in: (1) Shakers on machine columns, vibrated? by drills (2) Vials placed in drill holes to be blasted (3) Both homogeneous and heterogeneous. mixture with explosives ( 4) Packages with tamping (5) Compressed-air lines (6) Special compressed-air ejectors for use while drilling and after blasting (7) The discharge of ventilation fans (8) The filters of respirators It was concluded from this research that any adequate method of introducing aluminium powder into a mine atmosphere would require too much extra gear, supervision, and aluminium powder, and would interfere unduly with underground routine. Later, animal experiments by Denny, Robson, and Irwin(2) showed that aluminium powder provided effective therapy when inhaled independent of silica dust. Therefore, some means of surface treatment was deemed more practical.

Jan 1, 1944

By Yoginder P. Chugh

Beginning in 2010, a scientifically-founded water spray system for continuous miners (CMs) has been in development at Southern Illinois University that significantly reduces respirable dust exposure for workers in the face area (patent pending). It includes engineered sprays around the cutting drum, outer bitring sprays, chassis sprays and side cutter boom sprays. About 3.6?4.5 m behind these sprays are additional sprays that cover the area between the CM chassis and the mine roof and ribs. The innovative spray system uses approximately the same volume of water as spray systems currently used on CMs and with similar operating pressures. The innovative spray system design also takes into consideration coal dust wettability. An Illinois mine decided to implement these concepts on a CM during the rebuild stage. Dust control performance of the rebuilt CM was evaluated using gravimetric dust sampling and real-time monitoring with multiple personal dust monitors. The average results based on gravimetric sampling of about 105 cuts show about 30 and 20% reduction in dust exposure for the miner operator and the haulage unit operator, respectively. Visibility in the mining areas was also significantly improved. Since the initial demonstration, the coal company has implemented the system on all of their operating CMs.

Aug 1, 2013

By F. Doxey

Introduction In order to improve outputs and to reduce or hold mining costs, many attempts have been made to mechanize the getting and loading of coal in the major coal producing countries, and machines of various kinds and sizes have been designed and manufactured. Some of the most important are: Joy Continuous Miner Joy Coal Auger Goodman Mining Machine Lee-Norse Koal-Master Jeffrey Colmol Cardox Hordsecg Recovery Drill German Coal Plough British Coal Plough with agitated blades M. & C. Samson Stripper AB Meco-Moore Cutter Loader Joy Gloucester Getter The three last named are the chief longwall machines in use and the AB Meco-Moore and the Samson Stripper are doing a good job in their respective applications. It is understood that the Gloucester Getter recently installed in a British colliery also shows reasonable promise. It was felt, however, that to meet the conditions of the mines in Nova Scotia, any machine developed must have certain distinctive characteristics. It must: ( 1) Be able to cut and deliver coal in quantity and of the right sizes ( 2) Be easily manoeuvrable ( 3) Be suitable for longwall operations ( 4) Not interfere with timbers already set ( 5) Cut its own stable (6) Work on reasonably heavy gradients

Jan 1, 1951

By H. C. Cooke

"The Eustis mine, which was discovered in 1865, lies about 6 miles southwest of the city of Sherbrooke, Quebec, in lots 2, 3, and 4, range 9, Ascot tp. The mine was operated almost continuously from 1865 to 1937, under vanous owners.The ore was pyrite with varying amounts of chalcopyrite, a small amount of zinc blende and galena, and a low content in gold and silver. Parts of it ran quite high in copper, but the mine average would probably have been between 3 and 4 per cent. The high percentage of pyrite made it profitable to separate the ore into a copper concentrate and a pyrite concentrate. The latter was shipped away for manufacturing sulphuric acid, or was treated in a plant erected in 1887 at Capelton by the Nichols Chemical Company.The ore is a replacement of mica schist, which in turn was formed by the shearing of rhyolite flows. Ore also replaces the 'green rock', a term locally applied to carbonatized mica schists. The ore contained numerous 'horses' and smaller fragments of country rock, in all stages of replacement, ranging from those whose character was quite distinct to those whose ancestry could only be detected by an indefinite banding preserved in the sulphides."

Jan 1, 1954

By H. Vermette, J. Demers, R. Leclerc, P. Bergeron, P. Hudon, A. Lessard

The Arvida Smelter marked its 80th anniversary in 2006. Arvida currently operates 6 potrooms equipped with prebaked side-feeding pots producing 160 000t of aluminum per year, requiring the supply of 300 000t of alumina per year. In the past, to ensure reliable alumina supplies to the pots, especially in winter, a safety stock of alumina was kept inside the plant. The improved reliability of shipping on the Saguenay River has cut the need for such a stock. However, the stoppage of 8 Soderbergtechnology potrooms, starting in the 1980s up to 2003, generated alumina from the cleaning of pot pits, totaling 18000t and leading to the building-up of a significant alumina stock again. Concerns over working conditions, effect on potroom operations, and dust emissions prevented Arvida from tackling effectively this impressive alumina stock. Yet the increasing cost of alumina has created a strong motivation to use the stored alumina. In 2004 Arvida launched a project to recycle the stored alumina. This 4-year project aimed at clearing the alumina stock without affecting the operation of the smelter. It involved changing work organization, improving equipment and controlling the effect of the recycled alumina on the smelting process and working conditions.

Jan 1, 2006

By P. M. Chapman

Risks to aquatic receiving environments from uranium mining and milling fall into three categories: physical (habitat change), chemical (e.g., uranium, selenium, total dissolved solids [TDS], metals including vanadium), and radiological. Although all categories of risk need to be managed, chemical risks are the most significant and are typically chronic rather than acute. For instance, selenium toxicity is primarily manifested as reproductive impairment due to maternal transfer, resulting in embryotoxicity and teratogenicity in egg-laying vertebrates. Risk is best assessed using a weight of evidence approach focused on ecosystem services. Risk management should be based on both risk assessment and adaptive monitoring.

Aug 1, 2010

By C. B. Webber

"Sherritt Gordon's experience with rubber mill liners began in 1964 at the Lynn Lake Farley Mine and continued at the Fox Mine in 1960, and the Ruttan Mine in 1973. This paper describes the history of the performance of rubber mill liners at the three mine operations.LYNN LAKE - FARLEY MINEThe Lynn Lake Farley Mine, which ceased production in 1976 due to exhausted ore reserves, was a 3500 T.P.D. copper-nickel operation; consisting of two parallel rod mills followed by three stages of ball mill grinding. A circuit modification in 1964 necessitated one of the tertiary ball mills to be used as a pyrrhotite regrind mill. This 8' x 5' Hardinge conical mill drawing 225 HP was initially installed with steel liners and lifters. After several months of operation a routine inspection revealed severe channeling and washing behind the liners which was threatening to erode the ball mill shell. It was thought that the highly acidic condition in the mill, due to grinding 100 º6 pyrrhotite, was accelerating the wear of the steel liners. At this time it was decided to reline the mill with rubber liners to see if the wear problem could be relieved, and in December 1964 a set of Skega rubber liners were installed."

Jan 1, 1981