Search Documents

By Yun-Soo Lee, Su-Hyeon Kim, Hyoung-Wook Kim, Joon-Hyeon Cha

A7075 aluminum alloys have high strengths but poor corrosion resistance. In order to improve the corrosion resistance, a clad sheet is suggested, that is the A7075 alloy sheet bonded to A1XXX or A6XXX aluminum alloy sheets which are surface layers with good corrosion resistance. Mechanical properties of the clad sheets are determined by the combination of the component layer sheets, and thermomechanical treatment should be precisely designed when the strengthening methods of the core and the surface alloys are quite different. In the present study, three-layered A6022/A7075/A6022 clad sheets were fabricated by roll bonding process. Simplified processes incorporating a twin roll casting were also suggested in order to reduce the processing cost. Several temper methods composed of rolling, annealing, solution treatment, and aging were suggested in order to optimize the mechanical properties of the sheets. The strengths of the clad sheets were compared with the bare A7075 and bare A6022 sheets.

Jan 1, 2015

By F. Henríquez, V. Iriarte, L. Vinnett, J. Yianatos, F. Díaz

Metallurgical characterizations of the collective (Cu/Mo) and selective flotation plants were carried out in Minera Los Pelambres, Chile. The selective plant allows the valuable minerals of Cu and Mo to be separated. The evaluation involved two surveys consisting of metallurgical sampling as well as residence time distribution (RTD) measurements to determine load distribution. The RTD data were obtained in real-time by means of the radioactive tracer technique. In addition, metallurgical data was reconciled and supported by effective residence times. In the collective plant, a performance comparison of parallel rougher circuits was carried out, which included a bank of six mechanical cells of 250 m3 and banks of nine mechanical cells of 130 m3. In the selective plant, the Cu and Mo evolution along the plant was evaluated. The results in the selective plant allowed for performance evaluation of mechanical and pneumatic cells in primary flotation. In both plants, mineral losses were evaluated and their relationship with circuit configuration (cell types and circuit layout) was determined. The metallurgical characterization was a powerful tool to evaluate circuit performance and to detect improvement opportunities at industrial scale.

Jan 1, 2015

By Farzad Khodabakhshi, Adrian P. Gerlich

"In this article, cold spraying process was utilized to coat the surface of AZ31 magnesium alloy with a layer of AA7075 aluminum alloy. Thereafter, friction-stir processing (FSP) was employed to enhance the microstructure and consolidate the deposited layer. The grain structure and phase morphology were studied along with indentation hardness before and after cold spraying and friction stir processing. The magnesium substrate had an initial hardness of 74 HV which increased to 102 HV after FSP due to refinement of grains to <2 µm. The aluminum coating layer, provided improved surface hardness up to 160 HV, which further increased to 173 HV after FSP was applied.INTRODUCTION Cold spray is a material deposition process which can be used for surface modification, since it deposits material on a metallic substrate with little heating by way of high velocity ballistic impacts. Using cold spray technology, it is possible to deposit a wide range of coatings with various thicknesses by controlling the characteristics of the feeding powder and metal substrate, gas temperature, gas pressure, powder feeding rate, nozzle geometry, and gun traverse velocity. This process has been recently employed for surface modification in various aircraft and automobile structural applications. This has led to a broad range of research using this process for production and modification of different metallic and non-metallic systems. In the present study, cold spray process was used to deposit a uniform layer of aluminum-zinc alloy (AA7075) on the surface of AZ31 magnesium alloy. This coating was subsequently treated by way of friction-stir processing (FSP) as a new post-spraying modification technique to enhance the structural homogeneity and densification of the coated aluminum layer. This method utilizes a non-consumable rotating tool with a specially designed shoulder and pin that is plunged into the surface of metal to be modified and then moved along the direction of interest. The localized frictional heating between the rotating tool and workpiece leads to softening of the materials around the pin, and material extrusion through a complex flow of material from the advancing toward the retreating side the tool. To the author’s best knowledge, only a few reports discuss the modification of a cold sprayed deposit by FSP process. The microstructure and mechanical properties of the cold sprayed layer and substrate before and after FSP modification were examined using optical observations (OM) and indentation hardness testing. Furthermore, the AZ31 alloy substrate alone was treated with FSP as well, for the aim of comparison to the processed coating."

Jan 1, 2017

By Z. Ren, M. Tomlinson, E. Asselin

"Organic carbon blinding is a common, yet often partial, solution to the reduction of preg-robbing. A quantitative method to assess the extent of adsorption of a given blinding agent is presented herein. The adsorption of several blinding reagents on various carbon samples is quantified using electrochemical impedance spectroscopy (EIS). EIS results showed that kerosene is more strongly adsorbed on carbon than sodium lauryl sulphate (SLS), while SLS can hinder the charge transfer process of the oxygen reduction reaction on the carbon surface more effectively. The effectiveness of SLS is pronounced when its concentration is higher than 100 ppm. Raman spectra are presented for selected carbon samples: as the area ratio of the disordered peak to the graphitic peak increases, blinding agent adsorption increases.INTRODUCTION The presence of naturally occurring constituents in gold ores may adversely affect the extraction of gold in cyanide leaching since the gold cyanide complex, Au(CN)2–, can be adsorbed by these constituents (M. Adams & Fleming, 1989; Afenya, 1991; Miller, Wan, & Díaz, 2005). Such ores are known as “preg-robbing”. Preg-robbing behavior may arise from natural carbonaceous materials in the ore (M. Adams & Burger, 1998). In the past decades, a number of pre-treating methods have been developed for refractory carbonaceous ores (Arriagada & Osseo-Asare, 1984; Beer, 1994; Dunne et al., 2007; Jiang, Liu, Xiao, & Yang, 2012; Kohr, 1997; Kulpa & Brierley, 1993; Menne, 1992; Menne & Revy, 1994; Moyes & Houllis, 2010; Petrie, Craw, & Ryan, 2005; Simmons, 1996). The method known as blinding is one of the most effective and economical pre-treatment methods (M. D. Adams & Burger, 1998; Albert, 1923; Darrow, 1924; McQuiston & Shoemaker, 1975; Van den Berg, 2000). Blinding, also referred to as blanking or passivation, uses a chemical reagent to passivate the preg-robbing carbon by selective absorption or wetting (Bas, Altinkaya, Yazici, & Deveci, 2012; Brierley & Kulpa Jr, 1993; Dunne et al., 2012; Van den Berg, 2000; Yang, Qian, Song, & Dong, 2013; Yen, Amankwah, & Choi, 2008; Zhou, Jiang, & Choi, 2014). Organic reagents, which selectively adsorb on the surfaces of activated carbon and “smother” the surface, have been used for blinding carbonaceous matter in gold ores prior to cyanidation. Two comprehensive studies by Abotsi and Osseo-Asare and Adams and Burger have been published on this topic (Abotsi & Osseo-Asare, 1986; M. D. Adams & Burger, 1998)."

Jan 1, 2017

By Henrik Saxén, Mikko Helle

The operation of hot stoves used for preheating the blast in the ironmaking blast furnace has a strong effect on the consumption of reductants, economic performance of and CO2 emissions from the steelmaking site. Generally, it is recommended to maintain as high blast temperature as possible, because this minimizes the rate of reductants in the blast furnace. The blast temperature is affected in a complex way by the time periods of heating and cooling of the stoves, and by the amount of gas combusted in the stoves. Furthermore, as the hot stoves show degraded performance with age, it is a non-trivial task to select optimal operation parameters for the stoves. The paper addresses this computationally by applying a one-dimensional heat-transfer model of the hot stoves for optimization of the performance of the system. The complexity and strong coupling of the decision variables is demonstrated by numerical examples, where the blast temperature is maximized under different constraints.

Jan 1, 2015

By D. C. McDonald

"IntroductionTHE GIANT YELLOWKNIFE property is on the west side of Yellowknife bay, Great Slave lake, N.W.T., some 600 air miles north of Edmonton. This paper deals with the underground development and mining of the complex system of orebodies which have produced, in the first fifty-six months of operation (May, 1948, to December, 1952), 652,464 tons of ore with an average grade of 0.80 ounces of •gold per ton (1).The mine has been developed from three vertical shafts designated A, B, and C. Figure l shows the positions of these openings with respect to the known ore-bearing zones and the surface plant.A shaft was sunk to a depth of 522 feet in 1945-46, primarily as a prospect shaft for investigation and development of the East Zone orebody. Drifting was carried out on the 200-and 325-foot levels. Before this development had been completed it was clear that the funds immediately available made it imperative to get revenue from production as soon as possible. By the beginning of 1946, the remarkably high-grade character of the ore in the present B Shaft area had been established by surface drilling, and the decision was made to obtain initial production from this source. Since known orebodies at shallow horizons were to be developed quickly, the choice of a suitable rock outcrop for the shaft was something of a problem."

Jan 1, 1953

By H. Utsunomiya, J. Su, K. S. Tamimi, S. Yue, M. Sanjari, L. Kestens, A. S. Kabir, R. Petrov

The recrystallization and texture evolution of AZ31 sheets obtained through two stages was investigated at different stages of post-rolling annealing. The specimens were rolled at the temperature of 100? and at a fast speed of 1000m/min and low speed of 15m/min with a reduction of 30% in one pass. The results show thatAZ31B sheets rolled at 15 m/min and 100 °C has fractured for reductions of more than 30% per pass. However, by increasing the rolling speed to 1000 m/min the rollability was improved significantly and the material can be rolled to reductions of more than 70% per pass. The high speed and heavily deformed materials are fully recrystallized even at 100 °C.

Jan 1, 2015

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Preg-robbing may arise from natural carbonaceous materials in the ore. Several mechanisms have been proposed in the past decades including a physical sorption process by the carbonaceous matter, or via the reduction of aurocyanide at the mineral surface (Abotsi & Osseoasare, 1986; Afenya, Osseoasare, & Abotsi, 1983; Tan, Feng, Lukey, & Van Deventer, 2005). Nevertheless, the mechanisms of preg-robbing remain poorly understood. Understanding the nature of the preg-robber is of practical importance for the selection of a suitable treatment process. Fine carbon particles in the ore have been recognized as preg-robbers due to their similarity to the activated carbon used in the carbon in leach (CIL) or carbon in pulp (CIP) processes. Previous research has illustrated that the activated carbon (also referred to as amorphous carbon in some literature) has a much higher absorption ability than pure graphite with high crystallinity (Adams & Burger, 1998). Adams et al (Adams, Swaney, Friedl & Wagner 1996) concluded that carbonaceous matter is largely responsible for the overall preg-robbing capacity of a given ore. However, the mechanism of carbon preg-robbing was still not clear mostly due to the complexity of amorphous carbon and its behavior in different solution matrices, and at different pH and temperature (Adams, 1990, 1993)."

Jan 1, 2017

By T. Billotte, G. Tirand, J. Zollinger, V. Robin, B. Rouat, D. Daloz

The grain structure prediction of metallic alloys during a welding process is often an issue. In addition to the welding parameters and the alloy nominal composition and properties, the base metal grain structure and chemical homogeneity also play an important role in the formation of the final microstructure. In this paper intensive characterisation of solidification structure in gas tungsten arc welding of Ni base alloy 600 are described. It is shown that in transverse section of the weld, while the grain structure shows some texture following constrained solidification growth, grain density in the weld is similar or greater than grain density in the heat affected zone. This suggests that simulation of the welding structure needs, in order to be predictive, to take into account : epitaxial growth, secondary nucleation events and 3D growth inside the weld pool.

Jan 1, 2015

By A. McLean, A. Hue, K. Le, Y. D. Yang, P. Wu

While the treatment of relatively inexpensive ferrosilicon alloys is a potential refining route in order to generate solar grade silicon, phosphorus is one of the more difficult impurities to remove by conventional processing. In this project, the use of an electromagnetic levitation technique was used to investigate the dephosphorization of ferrosilicon alloy droplets exposed for various times and temperatures to a hydrogen-argon gas mixture. It was found that approximately 40% of the phosphorus was removed from an 85%Si-15%Fe alloy after 20 minutes exposure at approximately 1673K, to a gas mixture containing 48.5% hydrogen. Further dephosphorization is expected with longer reaction times. The effect of increasing temperature was found to be insignificant, although processing at lower temperatures is not only economically advantageous, it also decreases evaporative silicon losses, thus resulting in a more efficient process.

Jan 1, 2015

By S. Usui, Y. Shinohara, C. Tokoro, K. Horiuchi, S. Owada

Process optimization of heating and physical separation for Cobalt (Co) recycling from spent lithium ion battery (LIB) was investigated. LiCoO2 in spent LIB was transformed to LixCoO2 which was more easily decomposed than LiCoO2 by heating. Coexisting materials of aluminum and carbon, and sealed atmosphere of the LIB promoted LixCoO2 decomposition. In an atmosphere of Argon, 95 % of LixCoO2 in the spent LIB was decomposed to 76 % of Co oxide and 19 % of Co metal in 10 min at 823 K; a lower temperature than the theoretical value for LiCoO2. The Co oxide and Co metal exhibited magnetic properties and could be recovered by wet magnetic separation. Furthermore, slow heating was effective for grain growth of Co oxide and Co metal. At 2 K/min rate of heating, average grain size of Co oxide and Co metal were 239 µm and 28 µm respectively, whereas at 30 K/min they were 190 µm and 15 µm respectively. Therefore, separation efficiency for Co recovery by wet magnetic separation was increased when spent LIB was slowly heated at 2 K/min.

Jan 1, 2015

By M. J. S. Innes

Abstract This paper is an account of an investigation made by the Dominion Observatory with a gravity meter and magnetometer over sulphide concentrations at East Sullivan, Val d&apos;Or, Que., in June, 1947. The topographic relief over the area does not exceed 20 feet. The overburden varies from 0 co 50 feet. The west orebody had been outlined by extensive drilling. The average density contrast between the sulphide body and surrounding rocks is 0.5. Two hundred and sixty gravity and one hundred and ninety magnetic stations were observed. The results are shown on contour sketches. A derailed account is given of the methods employed to reduce the gravity observations. The survey shows that both gravimetric and magnetic methods are useful in delineating sulphide deposits under the conditions in which they occur at East Sullivan. The results indicate that the buried contact of the syenite intrusive southeast of the orebody could be traced with the gravimeter and chat the magnetometer was of little value for that purpose. Gravity anomalies due to the varying depths of overburden are negligible as compared to the magnitude of the total anomalies. Introduction The project was first suggested at a meeting of the Associate Committee on Geophysics of the National Research Council in September, 1946. At that time it was pointed out that the accuracy and speed of operation of the new gravity meters made them of special importance for geophysical prospecting and it was highly desirable to have an objective test of the performance of an instrument of this kind in delineating an orebody of known dimensions and density characteristics. Several years ago, a private company did some work with a gravimeter over the Amulet deposits, near Noranda. Unfortunately, the topography there is rather rugged, with hills and ravines exceeding 100 feet, so that the topographical effects rendered it impracticable to distinguish between anomalies due to the sulphides and those due to surface irregularities. An orebody of a typical nature, where the disturbing topographical corrections were not excessive, was therefore sought.

Jan 1, 1949

By Clemens Kuhnert

"Nickelhütte Aue GmbH is specialized in the recycling of waste materials containing non-ferrous metals. We treat nickel, copper, cobalt, vanadium, molybdenum and precious metal containing materials like spent catalysts, ashes, dusts, grindings, liquids, slurries and sludge's as long as they contain one or a combination of the above mentioned metals. In our pyrometallurgical works we produce non-ferrous metal concentrates suitable for further treatment in our hydrometallurgical plant where we refine Ni-, Cu-, Co- and V-chemicals. Our production is based on synergy effects due to the combination of pyro- and hydro-metallurgy. As an example we can mention our heat recovery system and internal recycling of by-products. Furthermore, the use of alternative fuels instead of fossil fuels contributes to the economic and environ-mentally friendly treatment system.INTRODUCTION Nickelhütte Aue GmbH (NHA) can look back on nearly 400 years of tradition as a pyrometallurgical works and recycling company. The existence since its foundation in 1635 as a blue dye works shows responsible and successful action in the past. Therefore, we see highest customer service, minimization of interferences with nature by closing material cycles and maximized health and occupational safety protection by avoiding injuries and diseases, still as our future duties. These duties are evaluated and monitored by an integrated management system that meets the standards of DIN EN ISO 9001, 14001, 50001 and BS OHSAS 18001. We commit ourselves to the observance of all juridical and customized demands. The management and the department managers perceive their model function. We require responsible action from all employees. To protect the continuity of our enterprise, we will also perform in future continuous improvement of products and their quality, as well as steady progress in the areas of environment protection, health protection and industrial safety. Equally the effectiveness and propriety of the management system is checked and developed regularly. In order to obtain the objectives resulting from this policy, our company determines activities and measures by involving all employees."

Jan 1, 2017

By L Tafaghodi Khajavi, M. Barati

The distribution of phosphorus between solid silicon and iron-silicon melt was determined to investigate the degree of phosphorus removal from silicon by solvent refining with iron-silicon alloys. The distribution coefficient which is the ratio of the mole fraction of phosphorus in solid to that of liquid is as follows: 0.22±0.02 (1310°C), 0.29±0.02 (1260°C) and 0.33±0.02 (1210°C). The removal percentage of phosphorus is: 84.2% (1310°C), 72.5% (1260°C), and 63.7% (1210°C). The average phosphorus content of produced silicon in the proposed solvent refining process would be over two times less than that of the conventional directional solidification. The values of interaction coefficient of phosphorus on iron at different temperatures were obtained as -3460±155 (1310°C), -3595±159 (1260°C) and -3694±119 (1210°C). Self interaction parameter of phosphorus at different temperatures are as follows: 68±4 (1310 ?C), 78±10 (1260 ?C) and 103±19 (1210 ?C). The calculated values for distribution coefficient of phosphorus at infinite dilution are: 0.22±0.00 (1310°C), 0.30±0.00 (1260°C) and 0.34±0.00 (1210 °C).

Jan 1, 2015

By S. Beskri, N. Geoffroy

When metallurgical plants are designed, a lot of consideration is almost always given to material selection and possible damage mechanisms. Materials engineers are generally involved and will strive to select optimal alloys or refractories for the design conditions. Once in operation however, things often change. Equipment is overstressed to increase production, corrosive leaks are not always promptly addressed, proper welding procedures are disregarded, etc. This paper describes various cases from the mining and metals industry where serious mishaps, associated consequences, and costs could have been avoided if simple and proactive steps had been taken. It also presents a strategy, based on safety reviews, to help predict and prevent damage to critical pieces of equipment.

Jan 1, 2015

By J. Sliwinski, H. Kikutani, J. Atwood, D. Larimer, J. Pyecha

"The Pogo mine start-up milling targets of 2005 are vastly different than the targets of today. Improvements have been driven by unintentional design oversight, continual circuit optimization or optimization due to changing mineralogy. The more significant process improvements to date have occurred in the gravity, flotation and leach/CIP unit operations. Details of the significant improvements are presented along with the impacts to the process.INTRODUCTION Deposit Overview Pogo mine is located along the Goodpaster River, southeast of Fairbanks, Alaska. This deposit sits in the center of the Tintina Gold Province (Figure 1), a region of similar Intrusion Related Gold deposits in Interior Alaska, the Yukon and British Columbia Canada (McCoy et al., 1997). The Pogo deposit is hosted in a rock sequence of amphibolite-grade gneisses intruded by mid-Cretaceous granitic plutons and dikes, which in turn, were cut by and host the auriferous quartz veins of the Pogo deposit.The Pogo deposit is comprised of three distinct zones of auriferous quartz veins spatially adjacent to each other. These are the Liese Zone, North Zone, and the East Deep Zone. The Liese Zone consists of three stacked, massive quartz veins, designated the L1, L2, and L3. Vein thickness averages 3.0 m, with variations from 0.3–18 m thick. The North Zone mineralization is comprised of four veins with more consistent thickness, between 1 and 1.5 m. The East Deep deposit lies northeast of the Liese Zone ore body. It is separated by a post mineralization, quartz diorite pluton. The East Deep Zone is comprised of two stacked massive quartz veins with similar orientation as the Liese Zone."

Jan 1, 2017

By V. Prasad, A. Afacan, K. Popli, S. Dubljevic

Froth flotation is one of the most common and widely used separation processes in the mineral processing industry; however, its complexity means that complete understanding of the process has not yet been achieved. A dynamic fundamental model is needed to enhance the understanding of the process and to improve process control. It is challenging to capture all the phenomena involved; hence, we propose a multiscale modeling approach with a framework ranging from macroscopic (equipment scale) to microscopic (attachment, detachment) models along with distribution models for ore particle sizes. Real-time froth properties are obtained using a vision-based sensing system. These measurements can be used for developing a soft sensor for grade using statistical methods such as PCR (principal component regression) and PLS (partial least squares) regression. The fundamental model is updated in real-time using extended Kalman filtering. Attachment dynamics are studied for different particle size distributions. The modeling and soft sensing is tested on batch flotation cell for the pure mineral galena with different particle size distributions using Xanthate and MIBC as collector and frother, respectively. The model, online measurements and soft sensor are useful in developing monitoring methods for froth flotation.

Jan 1, 2015

By Eduardo R. Rodrigues, Ankur Narang, Roberto Federico Ausas, U. T. Mello, Jose Maria Segura Serra, M. R. Lakshmikantha, Ignacio Carol, Kamal C. Das

"Modeling of big faults or weak planes of strong and weak discontinuities is of major importance to assess the Geomechanical behaviour of mining/civil tunnel, reservoirs etc. For modelling fractures in Geomechanics, prior art has been limited to Interface Elements which suffer from numerical instability and where faults are required to be aligned with element edges. In this paper, we consider comparative study on finite elements for capturing strong discontinuities by means of elemental (EFEM) and nodal enrichments (XFEM) for Geomechanical applications. For general fracture scenarios, Oliver et al. (2008) have demonstrated advantages of EFEM over XFEM for including: (a) ease of modeling in any standard finite element code due to the possibility of static condensation, (b) higher accuracy in some cases for coarse meshes, and, (c) a reduced computational cost. However, there has been no work that considers cohesive fractures in Geomechanics. We present a numerical analysis based on a linear constitutive model and linear triangular elements for the bulk and a linear constitutive behaviour for the fault for a representative set of fault planes in a circular tunnel made in rock mass. In the numerical examples we consider both well-traced and bad-traced meshes. We focus on traction profile analysis for both EFEM and XFEM, since that is crucial to understand the cohesive fracture behaviour specially rock joint. Therefore in each case, shear, normal and stress ratio are compared across the two methods along the fault plane. This is the first such work that compares XFEM and EFEM behaviour for Geomechanics problems.For the considered class of problems and the sharp penalization approach without regularizations adopted, it can be observed that accuracy and robustness of EFEM may strongly depend on the fault orientation with respect to the element edges, while, XFEM is independent of fault alignment with element edges. It has been also observed that, with mesh refinement model, stress oscillation completely removed with XFEM however EFEM fails to provide oscillation free results with finer mesh in case bad-traced model. We also performed error analysis and found that in case of bad-traced mesh the average error in the XFEM is 84% smaller than of EFEM and for XFEM the error goes to zero with increasing mesh resolution, while for EFEM the error increases with mesh resolution. Thus, we experimentally demonstrate that, XFEM performs better than EFEM in terms of accuracy and rate of convergence with marginal increase in computational cost. This work hence provides novel insights on the application of XFEM and EFEM in Geomechanics."

Jan 1, 2015

By M. Nakai, G. Itoh, R. Yamada, A. Kurumada

In order elucidate the mechanism for poorer fatigue properties of 7000 series aluminum alloys than those of 2000 series alloys, the effect of the test environment on the fatigue crack growth of the two series alloys was investigated, considering the relationship to hydrogen embrittlement. Two 7075-type and four 2024-type alloys were T6-tempered and T4-tempered respectively, and subjected to fatigue crack growth tests in moist and dry environments. When tested in moist air, fraction of intergranular crack path was higher in the 7075-type alloy with coarse equi-axed grains than in the 2024-type alloy with similar microstructure. This was in accord with the larger crack growth rate in the 7075-type alloy. Both the intergranular crack path fraction and the crack growth rate were decreased by changing the environment to the flow of nitrogen gas. Thus, the large fatigue crack growth rate of the 7075-type alloy is attributable to hydrogen embrittlement.

Jan 1, 2015

By P. C. Santos-Munguía, F. Nava-Alonso, O. Alonso-González

"The gold recovery of a Mexican cyanidation plant, in Sonora, has been decreasing due to the increasing presence of gold tellurides. This work presents the results of different processes aimed to recover the remaining gold from the cyanidation tailings of the operation. The cyanidation in the mine is performed at 0.1 g/L NaCN and pH = 10.3, adjusted with lime. The treatments studied in the laboratory with these tailings were: cyanidation at higher cyanide concentration than that used in the plant, cyanidation with oxygen injection, cyanidation with oxygen and lead nitrate addition, and thiourea leaching. The results obtained with each of these treatments are presented and discussed with the final objective of proposing a method to recover the gold associated with tellurium.INTRODUCTION It has been demonstrated that gold telluride is refractory to the conventional cyanidation process and, for this reason, some alternative methods to recover precious metals from tellurides have been proposed. (Zhang et al., 2010). These include cyanidation with modified conditions or the use of non-cyanide leaching agents. This work presents the gold leaching results of tests performed with a sample of cyanidation tailings obtained from a Mexican deposit containing telluride species. The mine exploits a mesothermal deposit with a molar Te/Au ratio of 1, containing also lead, molybdenum, bismuth and tungsten. Gold is recovered from the ore by standard cyanidation, however, lately the gold recovery has decreased, likely due to the tellurium content of the ore. The sample used in this work was the cyanidation tailings of this deposit. It was treated in the plant by cyanide heap leaching (0.1 g/L NaCN, pH = 10.3 adjusted with lime). Some gold remained after the cyanidation and it was thought that this gold was associated with tellurium. The objective of this work was the recovery of the remaining gold from the tailings by an alternative process."

Jan 1, 2017