Search Documents

By Robert W. Plummer

"This paper describes the use of Geographic Information Systems (GIS) as a tool for mineral exploration by using the Eskay Creek area of northern British Columbia as an example. Data entry, analysis and output are discussed. Examples of some of the capabilities of the technology are presented.The main benefit of the technology is being able to perform complex and sophisticated searches of large and diverse data sets to highlight exploration targets. A GIS is a powerful data management tool that can be used in mineral exploration. It is a computer based system that is designed for the collection, storage and analysis of objects and phenomena where geographic location is an important characteristic. The main function of the GIS is to produce information for the geologist from a variety of sources (geology, geophysics, geochemistry, mineral deposits and so forth) quickly and efficiently. This allows the geologist to examine large amounts of data in a fraction of the time than can be done using conventional manual methods."

Jan 1, 1992

By J. W. M. Porritt, K. C. Cheng

Knowledge of radon emanation rates from uranium-bearing rocks is essential to the design of mine ventilation systems for uranium mines. Measurements of equilibrium ratio between radon and its daughters in mine air are important for a better control of mine radiation conditions. The concentrations of radon and daughters were monitored at cut-and-fill stopes in the Beaverlodge Mine of Eldorado Nuclear Ltd. during all phases of the mining cycle. The radon emanation rates of ore and rock samples were measured at the laboratory and the results were compared with in-situ emanation tests in an isolated ore drift. Samples of backfill solution, backfill drainage and ground seepage water were measured [or radon and analyzed for radium and uranium. The results showed that discharges of backfill solution and daily shift-end blasts were the two major sources for a rapid release of radon gas in the ventilation air. Other mining operations, such as drilling, mucking, etc., contributed little effect on radon release to the mining environment. Radon emanation rates of the Beaverlodge are samples ranged from 13 x 10-18 to 600 X 10-18 Ci/cm2/ sec and that of waste rock samples from 0.54 x 10-18 to 13.4 X 10-18 Ci/cm2/sec. The in-situ emanation rate of mine walls with ore-to-rock ratios of 1 to 7 was 60 x 10-18 Ci/cm2/sec. The average equilibrium ratio of radon and its daughters in stapes was 32.6%. Under a normal ventilation condition, the average background levels of radon concentration in cut-and-fill stopes ranged from 13 to 80 pCi/L. The discharges of backfill solution during backfill operations at 100 tons solids per hour released approximately 1.8 x 106 pCi/min of radon and elevated radon concentration in stapes 2 to 5 times above the background levels.

Jan 1, 1981

By F. Lambert

"Amok Ltd./Cluff Mining operates a uranium mine at Cluff Lake in northern Saskatchewan. The project consists of one open pit and one underground mining operation along with a full-scale milling installation.The underground stoping operations are of the narrow vein type and are done between two levels 50 m apart. The mining method is undercut with concrete backfilling. Cuts are 3.5 m in height and can be as narrow as 1.4 m in width.Stoping operations are mechanized utilizing a CT-500E electric Microscoop marketed in Canada by Teledyne. The machine is only 85 cm in width and does all the mucking in stopes. Ore passes are provided in stope roughly every 40 m to 50 m.This paper describes the utilization of the CT-500E Microscoop in the company's underground operations and provides performance data related to the experience.IntroductionThe Amok Ltd ./Cluff Mining operation is located in the northwestern corner of Saskatchewan. The project started in 1980 with open pit mining and milling operations. In 1983, an underground mining operation began production . Today, the Amok Ltd./Cluff Mining installation produces 800 tonnes of uranium per year , which originates from both the open pit and the underground mine at about the same proportion."

Jan 1, 1990

By Claudia Gasparrini

"Silver occurs in about 200 minerals in variable amount s. Silver ores usually have 5 or 6 and in some instances as many as 10 species of silver minerals. All these minerals may have different flotation and leaching properties and should be correctly identified for successful recoveries. Grain size and host minerals which are critical in gold recovery, are not always as important for silver minerals.IntroductionMineralogical factors affecting the metallurgy of silver are , as for other metals: (i) the silver-bearing mineral s ; (ii) their grain size, and when dealing with very fine sizes; (iii) their host minerals; and (iv) the association they form with the silver-bearing minerals. Of these, the silver-bearing minerals are more often the cause of problems during recovery as opposed to gold whose metallurgy is generally more affected by grain size and host minerals. The problems derive mainly from the complexity of the silver mineralogy: over 200 minerals exist bearing the element in major, minor and variable amounts.As a member of group I-B of the periodic table, silver forms extensive so lid solutions with the other two elements in the same group , copper and gold. It combines with sulphur, tellurium and selenium in covalent bonds and with chlorine, bromine and iodine in ionic bonds. Where the fluid composition, temperature and pressure during crystallization allow it, silver also combines with arsenic, antimony, lead, bismuth, tin, mercury, indium, thallium, and germanium in many instances as a minor element in sulphide , sulphosalt and native element minerals. Cations which silver replaces to a lesser extent than copper and gold are iron, manganese, zinc and probably nickel and cobalt."

Jan 1, 1984

By Victor Rudenno

"Previous methods have employed statistical analysis to model future mineral resources. The method presented in this paper uses Zipj's Law to determine the size and grade of tin deposits still to be discovered. The law is applied independently to both known deposit tonnage and grades. A probability distribution for both 'tonnage and grade is computed/or those deposits still to be located and then, by applying a correlation between tonnage and grade, a distribution of the probability of metal content discovery is obtained.By considering an economic cut-off in metal contained in a deposit, the probability of economic success for the next tin discovery is computed, both for a world discovery and for the special case of Tasmania, Australia. The results indicate a probability of 11-37% on a world-wide basis and 18% chance of economic success in Tasmania.IntroductionIn the past , most attempts to determine the probability of success in finding an economic mineral deposit have relied on the accumulation of statistical data. These data are then used to predict a suitable frequency distribution to assess the probability of finding a deposit of a given size and grade (Singer,1975).The method not only relies on one having sufficient data, but also on the assumption that the data are not biased and that the distribution (usually log-normal) is a correct one. The method presented in this paper, to analyze tin deposits, uses Zipf's Law, which has been recently applied to oil, uranium, lead-zinc and gold deposits by Folinsbee (1977) and to Western Australian gold deposits by Rowlands and Sampey (1977). Tapp and Koniuszko (1978) have applied Zipf's Law to mineral distribution patterns in the Northern Australian orogenic provinces, which has enabled them to make predictions with a relatively small data source."

Jan 1, 1981

By R. P. Mahant

"Extensive pilot plant investigations were conducted both on partial roasting an d electric furnace smelting from September 1973 to August 1975.The objectives of the pilot plant investigations were:(I ) to confirm the application of available process technology to treatment of Falconbridge concentrate.(2) to examine partial roasting variables.(3) to investigate electric furnace smelting of roaster calcines .(4) to develop process design and operating parameters for a commercial plant.This part of the paper will cover the following topics:Partial Roasting InvestigationsPilot Electric Furnace InvestigationsPartial Roasting InvestigationsThe specific objectives were to:1. establish process variables for maximum oxygen efficiency and bed fluidi ation.2. determine the product distribution between the roaster and the various gas cleaning stages.3. produce a mass and thermal balance."

Jan 1, 1984

By T. R. Heflin

The paper provides a comprehensive discussion of pump selection for the hydrometallurgical industry. Material suitability, in addition to proper size and design, will provide extended life for pumps in erosion /corrosion service.

Jan 1, 1979

By M. K. Gangal, A. E. Hall, S. B. V. Stewart

"An investigation into the problem of atmospheric fog in Canadian mines is described. Fog occurs in several mines and the reduced visibility can result in the closure of workings for safety reasons. Information on the mechanisms of fog formation are discussed and the methods for improving conditions are reviewed with their relative costs.INTRODUCTIONAtmospheric fog occurs in several Canadian mines during spring and summer. The fog which reduces visibility, contributes to loss of production and increased accident risk . Closure of ramps in mechanized mines causes mining to be stopped or rescheduled, and stoping and grade control may be affected . Increased corrosion of equipment may result from acidic fog .Fog is commonly caused by saturated air being compressed and heated by an inlet fan and then being circulated in an ascensional system with heat transfer to the walls of wet airways. This causes supersaturation and water droplets condense to create fog, with liquid water contents of 0.5 g/kg to 3 g/kg of air. These concentrations reduce visibility to less than 10m and prevent mining. Less severe fog is usually tolerated as a nuisance, about which little can be done."

Jan 1, 1989

By Peter J. Franklin

"Short-term mine planning of open pits is an activity that has historically been carried out by hand. Typically, the use of computers has played little part in this type of mine planning. This paper describes the objectives and the procedures involved in short-term mine planning, comments on the type of computer systems available, and describes in detail a computer-aided short-term planning and scheduling system known as STEPS.IntroductionThe mine planning department of any o pen-pit mining operation performs a wide variety of different tasks. However, their primary concern is the preparation of detailed long-and short-term mine plans. These mine plan s will define the long-term operating strategies and definitive everyday working plan s for the ongoing development of the open pit.In this day and age, when operating costs have spiralled upwards due to inflation , and product revenues have decreased due to depressed economies and poor markets, it is vitally important for all aspects of the mining operation, including mine planning, to be efficient and cost effective.There are numerous options available for planning engineers when generating a mine plan. A cost effective mine plan must investigate all these options and select the optimum. When using manual planning techniques, it is often impossible to evaluate all the available options. To do this, and to produce an optimum mine plan, a computer is required.This paper discusses mine planning, with emphasis toward the short-term plan and comments on how the processes may be computerized. It also describes in detail, a computer software system called STEPS, which has been designed as an interactive graphics, computer-aided short -term mine planning and scheduling tool."

Jan 1, 1985

By S. Banisi, J. Marois, A. R. Laplante

"This paper compares the behaviour of gold and ore in the grinding circuit of Hemlo Mines Ltd. Particular attention is given to grinding kinetics, classification behaviour, and liberation. For grinding kinetics, laboratory grinding of gold flakes and silica, 840 µm to 1200 µm in size (14/20 mesh), was also performed to provide a standard for comparison and to study in a controlled environment the mechanisms of breakage, folding , smearing and impacting.Grinding kinetics were characterized at laboratory scale with breakage and selection functions. The breakage function showed that 75% of gold disappearing from the 840 µm to 1200 µm class reported to the 600 µm to 840 µm; this figure is much higher than for silica (46%) or most other minerals, and implies that comparatively fewer fine fragments are produced from the breakage of gold flakes, on account of gold's malleability. The selection function of silica was four times that of gold. At plant scale, the ratio of the selection function of ore and gold increased from 6 for at 50 urn to JOO pm to 20 at 500 um to 1000µm.Observation of original flakes and their fragments with the scanning electron microscope showed that the main mechanism of ""grinding"" from the 840 µm to 1200 µm to the 600 µm to 840 µm class was folding rather than actual breakage. This was confirmed by a measure of individual flake weight. The postulated breakage cycle is that relatively globular flakes become increasingly serrated through grinding; they can then regain their original shape through folding and reflattening into cylindrical and spherical shapes, as the majority does; however, some fragments will at this point undergo actual breakage. Photograhic evidence is presented to support the proposed mechanisms.Smearing of gold unto silica was observed when silica was ground after a gold, and embedding of silica into gold flakes when gold was ground after a silica. Both mechanisms occur whenever gold and harder minerals are jointly ground, and result in ""unliberation"" of gold. It is postulated that smearing of gold onto other minerals plays an important role in explaining how gravity recovery can increase over-all gold metallurgy, especially when used ahead of flotation.Classification of gold in the primary hydro cyclones takes place at a much finer cut-size than ore, 20 µm vs 57 µm. This and the slower grinding kinetics result in high gold circulating loads in the primary loop, 6700%, and a gold content in the primary cyclone underflow (PCUF) is twenty-four times that of the ore. The gold size distribution for primary cyclone overflow is much finer than that of the ore, although they are essentially similar in the PCUF.Liberation, or more accurately ""gravity recoverability"", was assessed with a 7.5 cm (3 in.) Knelson concentrator. It varied between the thirties for the primary mill discharge and two cyclone overflows, to highs of 89% and 92% for the PCUF and secondary mill discharge."

Jan 1, 1991

By D. Moffat

Rio Algom Limited has mined uranium at Elliot Lake, Ontario for 20 years. The production of this energy-generating element results in the need to dispose of low-level radioactive solid wastes and liquid effluents. Because of the wet-temperate climate at Elliot Lake, the liquid effluents are of particular importance. Radium-226 is the isotope which requires most attention, and the current practice for its control is by addition of barium chloride and retention of the resultant precipitates in large settling ponds. Analyses of typical effluents and waste streams are discussed and typical levels of radium-226, thorium-230, thorium-232, thorium-228, lead-2iO, polonium-2iO, and uranium isotopes are presented.

Jan 1, 1979

By Keith C. Hendrick

"Metal prices are frequently the most critical and least predictable element in determining the profitability of mining operations. Short -term fluctuations can be offset in varying degrees by hedging or other market actions. Such solutions are not practical for the longer term, The paper investigates the nature and extent of metal price risks and evaluates methods to reduce them.IntroductionIt is management's responsibility to improve the odds by managing the-risks by identifying them clearly, assessing them accurately, minimizing them where possible-and, then, timing decision s success fully.In determining the profitability of current operations, preparing forward plan s or developing feasibility studies for new projects or expansions, pr ices are usually the most critical input. Being market determined rather than cost based, they can also be the most unpredictable As a result, commodity prices are frequently the greatest of all risk factors.Nature of Commodity PricesThe cyclical nature of commodity prices is well known. They are stable only when supply is in balance with demand and forecast to remain that way. An imbalance on either side of the equation can lead to a price reaction completely out of proportion to the actual or perceived surplus or shortage.This exaggeration arises through the cumulative effect of market forces. When the market senses an uptrend, consumers buy for the expected increase in activity. They also seek additional quantities for inventory before price s rise. Merchants defer spot sales anticipating higher price s, speculators go along for the same reason, and producers raise prices in response to demand. Events tend to confirm the expectation of each party and strengthen their reaction causing prices to move higher."

Jan 1, 1983

By G. R. Guillet

"Bricks made from local Paleozoic shales, and floor and wall tiles made from imported clays, both established record production volumes in 1985 and are the strongest segments of Ontario 's clay products industries. However, renewed interest in traditional materials also supports a good market for clay flower pots and flu e liners, and innovative processing studies are showing promise for possible new production of clay roofing tiles. This paper reviews the highlights of a comprehensive study of Ontario's clay products industries, completed in 1986. IntroductionFor some years now, Ontario' s clay products industries have been unspectacular in their attempt to cope with the recent recession and the impact of alternative materials. But a strong demand for bricks in recent years has done much to dispel the gloom.Bricks, drainage tiles, sewer pipes, flue liners, structural and partition tiles, and flower pots have been commonly referred to as ""heavy"" clay products, and they have been based largely on local clays and shales. To this list might be added expanded aggregate and mineral wool. Clay refractories, sanitary ware, electrical porcelain , art pottery, and floor and wall tiles are not considered heavy clay products, and are commonly made from a variety of ceramic materials, many of which are imported.Production facilities for heavy clay products often began in Ontario as small family enterprises, using whatever clay was available locally to supply the local market with building bricks and other clay products needed for construction. Improved road systems increased the market range for these plant s, and new technology and industry standards resulted in gradual"

Jan 1, 1988

By G. R. Guillet

"Bricks made from local Paleozoic shales, and floor and wall tiles made from imported clays, both established record production volumes in 1985 and are the strongest segments of Ontario's clay products industries. However, renewed interest in traditional materials also supports a good market for clay flower pots and flu e liners, and innovative processing studies are showing promise for possible new production of clay roofing tiles. This paper reviews the highlights of a comprehensive study of Ontario's clay products industries, completed in 1986. IntroductionFor some years now, Ontario's clay products industries have been unspectacular in their attempt to cope with the recent recession and the impact of alternative materials. But a strong demand for bricks in recent years has done much to dispel the gloom. Bricks, drainage tiles, sewer pipes, flue liners, structural and partition tiles, and flower pots have been commonly referred to as ""heavy"" clay products, and they have been based largely on local clays and shales. To this list might be added expanded aggregate and mineral wool. Clay refractories, sanitary ware, electrical porcelain, art pottery, and floor and wall tiles are not considered heavy clay products, and are commonly made from a variety of ceramic materials, many of which are imported.Production facilities for heavy clay products often began in Ontario as small family enterprises, using whatever clay was available locally to supply the local market with building bricks and other clay products needed for construction. Improved road systems increased the market range for these plant s, and new technology and industry standards resulted in gradual upgrading and consolidation of them as traced in Table I"

Jan 1, 1988

By R. K. Singhal

"On the mining side the Canadian oil sands industry has become proficient in excavation and disposal of ore and overburden. Nearly twenty years of mining experience is now behind this industry. While local improvements to existing mining systems and practices will continue, it is believed that some further gains in productivity can be achieved by selectively introducing new ideas from other mining and non-mining industries. This type of technology transfer is vital for over-all cost-effective technology enhancement of oil sands mining operations.Discussed in this paper are the issues of mining equipment, equipment sizing, microprocessor and computer based technol¬ogy as applied to mine-wide data management, automation and remote control and a projection of likely mining systems in the year 2000!This paper reviews the ""state-of-the-art"" in selected surface mining systems and attempts to evaluate the forthcoming technology and its application."

Jan 1, 1989

By D. King

Outline ? Regional Geology and Deposit types ? PM Deposit Exploration History and FNX?s Exploration Strategy ? Deposit Geology and Interpretation ? Resource Estimation ? Reconciliation ? Conclusions ? Breccia of comminuted footwall rocks from passage of shock wave due to meteorite impact ? Matrix ?pseudotachylite?-like? ? Variable re-crystallization of matrix due to thermal metamorphism &/or alteration

May 1, 2006

The mixer that is commonly encountered in hydro metallurgical operations consists of a single turbine and tank combination. However, it would be advantageous to examine some common solvent extraction mixing systems in the light of the fundamentals of chemical reactor design. The basic concepts of reactor design are commonly used in the chemical industry, and it should not be too difficult to apply them to solvent extraction. The factors that affect the engineering design of a reactor are: the reacting system; the type of reaction; and the configuration of the reactor. The reaction system in solvent extraction consists of a heterogeneous liquid phase, involving two immiscible liquids. It is essential f or the process that the reactor product can be separated efficiently in the subsequent settler. The type of reaction in solvent extraction system may be quite complex, and the picture is complicated by the presence of competing and side reactions. The reactors themselves have been generally continuous stirred tanks, and the nature of the mixer-settler makes it unlikely that the pumping mixer can be dispensed with. However, it appears that there should be some definite advantages to a system of stirred reactors in series. The kinetic experiments which are carried out should have the definition of optimum reaction conditions as one of their goals. The data obtained from these experiments must also be applicable to the design of reaction equipment. Reactor selection and design is often a unique problem for each chemical process, and does not lend itself to a systematic general approach. However, the application of chemical and physical principles to mixer design in solvent extraction should result in practical, more efficient plants.

Jan 1, 1979

By S. Pauly, U. Kühn, J. Eckert, I. Kaban, G. Wiehl, F. Silze

In the present work, the effect of Ga on the wetting behavior of the Cu-rich braze filler CuGa10 (wt.%) on the steel 304L was investigated. For this, the macroscopic and microscopic effects governing the wetting of pure Ga, pure Cu and CuGa10 alloy (wt.%) on the austenitic steel were analyzed and compared. Contact angle and surface tension measurements were carried out by means of the sessile drop technique and, in addition, the phase formation at the interface was determined. Pure liquid Ga spreads on 304L, which supposedly is related to the formation of intermetallic Fe-Ga phases growing into the liquid Ga. Depending on the annealing time, FeGa3 and Fe14.5Ga12 were identified. In contrast, CuGa10 as well as pure Cu show secondary wetting on the steel surface. Especially, liquid Cu prefers to spread laterally and vertically along the grain boundaries of the steel substrate. In spite of rather similar mechanisms, CuGa10 wets 304L steel at lower rate than pure Cu above the liquidus temperature.

Jan 1, 2014

By Bo-Hyun Kim

Outline ? Strainburst criteria and hypotheses adapted for this study. ? Influence of excavation method on rock mass properties. ? Excavation disturbance factors vs. deformation modulus, etc. ? Estimation of blasting damage zone around excavation. ? Considerations of energy on burst-prone ground. ? Literature review & closed form solution. ? Numerical simulations. ? Summary and future works.

Oct 1, 2010

By R. F. Engler

"IntroductionThe Coal Branch region of west-central Alberta has been the focal point for unprecedented exploration and development activities over the past ten years prompted by the renewed markets for high-quality thermal coal. Although mines were developed and operated extensively throughout the region from 1910 until 1960, information relating to the detailed stratigraphy of the coal measures and their areal distribution tended to be localized to individual mine sites. Continuity along trend was impaired by a paucity of outcrop restricting geologic mapping to stream bank and roadside exposures. Recent studies and subsequent publications by Jerzykiewicz and McLean of the Geological Survey of Canada (1978, 1980) have established a detailed sedimentological model and defined the stratigraphic nomenclature for the region . The term Coalspur Beds has been adopted to describe the coal-bearing sequence between the overlying Paskapoo Formation and underlying Brazeau Formation. Complete sections of the Coalspur Beds have been compiled from sub-surface borehole data and published by Manalta Coal Ltd ., Dentherm Resources Ltd. and Luscar Stereo Ltd. This paper is an attempt to correlate this information on a regional basis to illustrate trends within the Coalspur Beds."

Jan 1, 1986