Search Documents

By F. Melo, M. Pawlik

Fine coal aggregation in concentrated coal-water suspensions was studied through steady-state rheological measurements. The wettability of coal particles was modified by dry oxidation of a bituminous coal. The degree of hydrophobicity was monitored using film flotation. The rheological measurements revealed that hydrophobic coal particles aggregate in aqueous suspensions, over a wide pH range, and produce slurries with high yield stresses. As the degree of coal oxidation increases, the coal particles become more hydrophilic and such suspensions exhibit lower yield stresses values. The yield stress values for suspensions prepared from oxidized/hydrophilic coal become a strong function of pH and correlate well with the surface charge as determined through electroacoustic measurements. These results indicate that the yield stress of aqueous suspensions of coal, and hence coal particles aggregation, is strongly affected by the wettability of coal particles.

Jan 1, 2004

By Namavari. H., M. Ashouri, M. R. Sarhadi, S. H. Mansouri, A. Sarrafi

The splash phenomenon and its effective parameters in metallurgical converters have been studied thoroughly for decades. The detailed studies of processes such as tuyere blockage, wave formation during air injection, entrapped phases, and also processes which control the formation of bubbles in viscous fluids are not feasible yet. In this research, we have used a converter-shaped vessel made of flexi-glass. Water and oil have been used as matte and slag phases respectively. The effective operational factors responsible for creation of splashing have been studied such as air flow rate, tuyere angles, depth of tuyere submergence, tuyere blockage, density and viscosity of liquids, liquids heights, etc. The results have been found as follows: the amount of splashing increases slowly as air flow rate increases. However, as the air flow rate reaches a critical value (depending on the physical specification of converter) the amount of splashing rises sharply, because the flow of air inside the liquid changes from bubbling into a jet stream; and most of the splashed materials are in the form of filaments instead of droplets. Changing tuyere angle from horizontal towards vertical position will increase the turbulence level on the fluid surface and causes an increase in the amount of splashing. The effect of tuyere submergence is related to the converter opening angle. As the converter opening angle is shifted towards the hood position, the amount of tuyere submergence and splashing will increase. As density of the liquid increases, the number of droplets splashing increases with a decrease in drop size. Therefore, the total amount of splashing decreases. However, as viscosity of the liquid increases, the splashing material increases due to the changes in the splashed material from droplet shape into filament form. The height of liquid inside the converter, depending on the relative height of heavy phase and light phase, is an important parameter regarding splashing. As the relative height of heavy phase to light phase increases the splashing will decrease. The tuyere blockage will cause the pressure in the inlet manifold to increase; and in real cases will increase the splashing. Finally, we have development a model based on dimensional analysis to relate the above parameters in order to calculate the amount of splashed material.

Jan 1, 2007

By Robert D. McKellar, Luke Frawley, Richard Okrasa

"The resource industries in Canada are facing increasing global competition and stringent environmental regulations. This has made it essential for companies to lower operating costs wherever possible. Electrical energy rep-resents one variable cost that may be better managed and utilized, providing the user with lower operating costs, improved productivity and better yields.The utility industry is also facing changes in the way it must do business. Utilities in North America are facing the prospect of deregulation that will eliminate the monopoly they have traditionally held. This will force them to strive for lower operating costs, to maintain a competitive position and to improve customer ser-vice so as to maintain their customer base.Ontario Hydro has been working with industry for several years. Many opportunities for cost savings have been identified involving energy efficiency, process improvements and the use of new electro technologies. One useful service that the utility can offer industry is to increase the awareness of potential opportunities suited to their operations. This paper will provide an overview of some of the projects that have been implemented and those that are presently being evaluated. An electronic data-base of electro technology applications that is under development will also be described."

Jan 1, 1996

By Dao Dac Tao

The Vietnam coal industry in recent years has achieved the rapid growth. However, in the process of industrialization and modernization of the country, the demand for coal for energy is constantly increasing. This paper presents the Vietnam coal industry in the last stage: the opportunities and challenges facing the coal industry as it strives to become modern, highly effective and capable of meeting the demands of national energy security, all in harmony with socio-economic and environmental needs.

Aug 1, 2013

By C. A. Sosa-Blanco

Minera Sabinas in central Mexico treats a complex sulfide ore containing galena, chalcopyrite, sphalerite and argentite as valuable minerals, and in some cases important amounts of non-magnetic pyrrhotite. For high pyrrhotite ores, results obtained by selective flotation showed good grades and recoveries in the lead-copper circuit, but a commercial zinc concentrate could not be produced due to the high floatability of pyrrhotite. When this is the case, an alternative method was proposed to produce a bulk concentrate by flotation which is then leached to recover copper and zinc from liquor in a SX-EW circuit. Leaching was conducted in an autoclave in order to study the effect of temperature and pressure, but bioleaching tests were also conducted. Leaching lead-silver residues were treated by cyanidation in order to recover silver values. The results obtained by selective flotation and by bulk flotation with leaching of the bulk concentrate showed that the latter alternative increased zinc recovery by 30 % with similar recoveries of the other metals.

Jan 1, 2007

By K. S. Raja, B. McNall, B. Pesic

"High-level radioactive wastes are stored in large underground storage tanks made of low-carbon steel. The wastes consist of concentrated solutions of sodium nitrate (NaNO3) and sodium hydroxide (NaOH), and the radionuclides 137Cs, 99Tc, and 90Sr. The corroding steel microenvironment may produce localized reducing or oxidizing conditions that affect the solubilities of the species such as Tc(VII) and Tc(IV), which in turn modifies the kinetics of corrosion of the storage tank. To understand the influence of technetate ions on the corrosion of steel, electrochemical polarization studies of A 537 steel samples were carried out in 1 M NaNO3 + 0 .05 M S r(NO3)2 + 0.1 M NaOH with and without addition of HReO4 at different temperatures (24 – 85 °C). The concentration of HReO4 was varied from 0.014 – 0.04 M.INTRODUCTIONAqueous processing of spent nuclear materials generates a large amount of high-level radioactive wastes. The wastes are primarily salt solutions of sodium hydroxide and sodium nitrate which also contain fission products such as 137Cs, 99Tc, and 90Sr. Among the high level radioactive fission products, Tc-99 is of great importance because of its high concentration, long half-life (2.1 x 105 years), high solubility in geologic waters as technetate, and rapid diffusivity through the geologic systems. The solubility of technetate ions varies depending on the oxidizing conditions prevailing in the storage containers. High level radioactive wastes are stored in single shell or double shell tanks made of low carbon steels such as ASTM type A15, A516-70 and A537. Most of the available literature on corrosion of steel in simulated radio active waste environments pertains to nitrate induced stress corrosion cracking (Subramanian & Mickalonis, 2005). The corroding steel microenvironment may produce localized reducing or oxidizing conditions that affect the solubilities of the species such as Tc(VII) and Tc(IV). Corrosion of steel and formation of Fe(II) and Fe(III) will affect adsorption and reduction of Tc species. The radioactive species can irreversibly be sorbed on the steel surface by oxidation of Fe(II) to more stable Fe(III) and fixed as less soluble Tc(IV)/Fe(III). The solubility of Tc species is also affected by other factors such as dissolved oxygen, local pH, temperature etc. How the corrosion behavior of steel will be affected in the presence of Tc species is not clearly understood.Cartledge (Cartledge, 1960) demonstrated that passivation of iron can be achieved in the presence of oxygen along with suitable inhibitor ions/molecules of the general formula XO4 n-, such as pertechnetate (TcO4 -). The pertechnetate ion is univalent. Since it is derived from a strong acid, no buffering action can be expected from this ion. The redox potential of the reaction (1) is 0.738 VSHE (Pourbaix, 1974)."

Jan 1, 2012

Phelps Dodge has recently operated a commercial scale, super fine grinding circuit of copper concentrates for use in a medium-temperature pressure leaching process. Two 355 kW vertical stirred mills were installed in series, targeting a grind of 80% passing 7.5 µm and 98% passing 15 µm as outlined in Phelps Dodge's concentrate leaching patent portfolio. This paper details the operation and results of the test program at Bag dad, as well as some of the operating challenges encountered.

Jan 1, 2007

By E. N. Gilje

"IntroductionDURING the past five years, over two miles of shaft sinking have been completed at Falconbridge. As sinking has continued, we have improved our equipment and technique with a resulting increase in efficiency. Throughout this period, all sinking has been done by contracting firms, under our direction and to our equipment specifications, with highly satisfactory results. Since 1949, Riddell shaft mucking machines have been successfully used in conjunction with the •benching method of sinking. Our most recent practice can best be illustrated by describing the method used in sinking No. 1 shaft at the Fecunis Lake mine.No. 1 Shaft, Fecunis Lake MineNo. 1 shaft, consisting of six compartments and measuring 13 ft. 11 l/2 in. by 19 ft. 9 3/8 in., outside timber (Figure 1), will be sunk to a depth of 4,170 feet. It was designed to accommodate two 10-ft.diam. Koepe hoists."

Jan 1, 1955

By Frank D. Adams

The Island of Ceylon, which is one of the most beautiful possessions of the British Empire, has been an abode of man from the very earliest times. The Veddhas, a wild tribe of some 4500 people still living in the fastnesses of the jungle in east central portion of the island, are believed to represent a remnant of the oldest inhabitants of which we have any actual knowledge, but in the caves in which they live there are found the stone axes and other implements of Palaeolithic people who represent the first race of men who inhabited our globe, and of whom they may be, for all that is known, the direct descendants. About the fifth century before Christ there came the Aryan invaders, apparently from the north of India, who drove the Veddhas into the remote fastnesses of the jungle and developed the remarkable Singhalese civilization whose high character is demonstrated by the remarkable and very extensive system of irrigation works which they built up, and through which they made the island wonderfully productive. Great cities arose, some of which are believed to have had a population of over a million souls and whose temples and public buildings show that the people were accomplished architects and sculptors.

Jan 1, 1926

On the recent trip from Vancouver to Calgary with the President, Mr. C. C. Huston, and yourself, I had the opportunity of outlining a plan based on the following: Among the aims of the Institute are, obviously, the fostering of the confraternity of those engaged in the technical and management fields of the mining and petroleum industries. This may be achieved in a number of ways, of which, to me, the interchange of ideas and experience between different parts of Canada and different sections and divisions of the Institute appears to be one of the most important. I think you and the membership as a whole are, and have been, well aware of this. The annual tour of the President .and Secretary, particularly their visits to Branches, shows this to be true. The interchange of ideas through the medium of the BULLETIN also illustrates the point; indeed, most Institute activities are directed along these lines. I am convinced that much more could be accomplished if it became financially possible to do so. Many able and fine men are, I think, willing and anxious to give their time and energy to furthering these phases of Institute activity, but it is unfair to expect them to assume as well the financial obligations involved. Specifically, I would suggest that the following could be done if sufficient funds were available:

Jan 1, 1952

By R. Viljoen, K. Manns

"The mining industry instinctively follows rule-of-thumb design velocities often based on very simplistic theoretical “economic velocity” optimization calculations to determine airway sizes. Although these are important building blocks in ventilation planning it should be recognized that mines are far more complex and various, often opposing factors, are at play. Therefore, it is important that each ventilation situation be analyzed on a case-by-case basis to determine the best-fit solution for an operation. The ventilation design process should not necessarily be constrained by theoretical optimal economic velocities that become rules-of-thumb. In some cases, this could lead to unrealistic infrastructure requirements and exorbitant capital expenditure. This type of design often lacks corporate support leading to a scenario where no ventilation upgrades are implemented. Economic velocities typically consider the cost of power, development costs and operational risk. These typical rules-of-thumb work reasonably well as a starting off point when considering feasibility of greenfield projects. For established mines that are looking at expansion these rules may not be appropriate due to capital expenditure constraints or geotechnical ground conditions. The theoretical optimum should be reviewed in the case of an established mine where existing infrastructure could perhaps be maximized. For example, the geotechnical risk of large diameter raises at depth may require multiple small diameter raise to maintain the theoretical economic velocity. If a mine has a life of less than 5 years, then the cost of power is an insignificant proportion of the total owning cost. For these mines, operating the ventilation raises at an increased velocity to avoid a complicated and expensive capital upgrade might be the more appropriate option, even though it opposes the traditional rules-of-thumb. Mines which are capital constrained may be better off accepting a higher operating cost for the interim or settle for minor infrastructure upgrades rather than run the risk of the entire ventilation upgrade not being approved at all. This paper explores a number of examples derived from case studies undertaken by the authors for several deep mechanized mining projects in Australasia. The examples explore conditions under which higher than the economic norm would be applicable."

Jan 1, 2019

By D. L. Morgan, J. A. Butterfield

"Geological data, production trends and current projects underway suggest that enough molybdenum will be available from more diversified sources to meet the world's growing demands. The growth in molybdenum consumption has been primarily related to its beneficial effects as an alloying agent in steel. This rapid growth has been deliberately fostered by stable prices, adequate supply and application research. The molybdenum industry is now in a process of change which has been seen in several other metals, such as aluminum and nickel. As supply sources have become more diversified, the market has become more competitive. The recent drop in consumption has led to excess production capacity, accumulation of substantial producer inventories and increased market uncertainties. While consumption is expected to increase in the next two to three years, it will take some time to absorb the excess capacity and inventory. The increased proportion of by-product capacity indicates that prices may become more variable. Producer discipline will be required to prevent serious price erosion in times of surplus. Future prices may not continue to increase with inflation. For the longer term, several factors favour the increased consumption of molybdenum. Engineering requirements are becoming more severe and molybdenum alloys can help to meet these changing needs. In addition, consumers can rely on a large and increasing supply of molybdenum. A 7 per cent growth rate in consumption can probably be sustained through the next decade, but new applications and reasonably stable prices will be needed to make this possible."

Jan 1, 1972

By Albert G. Zima

THE conservation of strategic materials during war rime gives rise to many problems not commonly encountered in times of peace. During normal times, when world trade is unrestricted, we are apt to become lavish to a point of extravagance in our use of those materials which, during rime of war, become scarce owing to inadequate transportation and production facilities or because the enemy may be in position to control sources of supply. It becomes necessary, then, to enforce rationing of available sup-plies, and in some cases, where such supplies are wholly inadequate, we find we must resort to the use of substitute materials. We are now confronted with such a problem to an extent never before experienced, with the result that many of the commodities upon which our civilization depended are now either shut off completely or, because of the heavy demand occasioned by war production, are not available in sufficient quantities to meet requirements predicated on peace-time standards and manufacturing methods. It has become necessary, therefore, to make many changes, some of them very drastic indeed, to enable us to carry on our war effort effectively. This? discussion will deal briefly with one phase of this problem, namely, the conservation of alloys required in the making of steels necessary for war production. In line with a request from the War Production Board, the Technical Committee on Alloy Steels of the American Iron and Steel Institute made a study of experimental steels embodying the !east amount of alloying constituents, with the objective in mind of substituting these steels wherever possible for the standard alloy steels used heretofore. This study embraced the following phases: (1) The availability of silicon and manganese; (2) The average quantity of alloying elements recoverable from scrap; (3) The effect of increases in manganese and silicon contents on the general properties of steel; ( 4) The elements and ranges of elements which might be used to duplicate the hardenability of the steels now in use; (5) The effect of combining several elements in small quantities upon the properties of steel at various hardness and strength levels; (6) A determination as to whether or not the steels selected would suffice for general application. Working on this basis, the Committee arranged for the manufacture of several heats of steels containing various combinations of different amounts of such elements as silicon, manganese, chromium, nickel, and molybdenum. The steels thus produced were compared by hardenability tests.

Jan 1, 1943

By H. P. Dibbs

An account is given of the application of neutron activation analysis to the rapid, non-destructive determination of copper in minerals, using a 14-MeV neutron source. Elements that interfere in the determination of copper by this method are given, together with the errors in the estimation of copper that result from the presence of varying amounts of these elements. The possible use of a compact "sealed-tube" 14-MeV neutron generator for the field assay of copper in minerals is discussed.

Jan 1, 1970

By M. M. C. Lima, L. C. S. Solimani, M. A. Quintela

Galvanized steel scrap is recycled to B OF converters where zinc escapes from the bath and is captured by the gas control system, appearing in BOF sludge. As BOF sludge contain high iron content, it could be recycled, but due to its zinc content, it is disposed in landfills. In this study techniques were evaluated for zinc layer removal from scrap by sulfuric acid leaching. The effects of coating weight, temperature, time and sulfuric acid concentration were evaluated for three different galvanized scrap. The results showed that the behavior of each galvanized scrap was different. Nevertheless zinc removal efficiency was more than 80% with low dissolved iron in the leached solution.

Jan 1, 2011

By A. C. A. Howe, J. C. Rowntree

"The Bernie Lake pegmatite near Lac Du Bonnet in southern Manitoba is a complexly zoned pegmatite containing several lithium-bearing units in addition to the western world's largest known reserve of cesium. The pegmatite forms a flat-lying ellipsoidal body within an east-west-trending Precambrian amphibolite. The pegmatite enclosed by this vertically schistose amphibolite lies near the eastern tip of a granitic intrusive. The relationship of this intrusive to the pegmatite is obscured by Bernie lake. To date, the pegmatite body has been delineated aver an area of approximately 80 acres; it attains a maximum thickness of 280 feet. Several distinct zones, including three assemblages of economic importance, comprise the pegmatite itself. The combined spodumene and lepidolite assemblages provide a recoverable defined lithium ore reserve of almost 5 million tons averaging more than 2 per cent lithium oxide. The recoverable cesium ore of the pollucite assemblage provides 300,000 tons averaging more than 20 per cent cesium oxide; this represents more than half of the western world's pollucite reserve. The Bernie Lake pegmatite deposit, owned by Chemalloy Minerals Limited, is well located with respect to the growing United States markets, and its reserves of cesium are large enough to enable it, under favourable economic circumstances, to become the major producer of this metal in North America."

Jan 1, 1967

By G. Mousavian, R. Bagheri, N. Dalili

Polypropylene (PP) and its composites have an increasing use in automobile and domestic industries. Since the published results on strain rate effect on yield behavior do not match, and there is a high attention paid for effect of nanometeric fillers on deformation behavior of composites, in this research the strain rate effect on yield behavior of PP and the effect of nanometeric fillers on deformation behavior of PP have been studied. Microscopic observations and tensile tests in different strain rates on neat PP samples and on samples filled with 5, 10 and 15 %wt have been used. A dramatic change in behavior for the modulus and post-yield slope curves when the strain rate is between 0.0433-0.05 s-1 has been observed. Microscopic observations on PP indicate a change in deformation mechanism from shear yield to crazing at the same strain rate that the change in behavior of curves occurs. It has been observed that in PP nanocomposites with higher amount of calcium carbonate, fracture in early stages of deformation occurs in lower strain rates. In other words for a fixed stain rate there is a critical filler percentage such that if the filler percentage is higher then early-stage fracture will occur. Similarly for a fixed filler percentage there is a critical strain rate and in higher strain rates early fracture will occur. The critical stain rate will decrease as the filler percentage increases and vice versa.

Jan 1, 2006

By Qin-yong Ma, Jing-shuang Zhang, Bo Han, Pu Yuan

In order to improve the utilization rate of blasthole and blasting effect in vertical shafts, 5 kinds of millisecond blasting model tests with three circle vertical blastholes have been conducted in various delay times with concrete as model material. The blasting effects of millisecond blasting model tests are investigated from cutting volume, cutting depth, and blasting fragmentation, then a reasonable delay time is obtained. In the middle of concrete model, there are 4 blastholes uniformly distributed in the first circle, 6 blastholes uniformly distributed in the second circle, and 10 blastholes uniformly distributed in the third circle. Each blasthole is charged with one millisecond delay electric detonator, and the rest is blocked with stemming. The depth of blastholes in the first and second circle is 180mm, which is 20mm deeper than those in the third circle. After initiation, the blasting cavity is cleaned up, then the cutting volume and cutting depth are measured. Meanwhile, the blasting fragments are gathered and have analysed by function Rosin-Rammler. The test results show that when the inner two circle blastholes initiated simultaneously and the third circle blastholes initiated with millisecond delay, the reasonable delay time is 50 ms. At this time, the cutting volume and cutting depth of blasting model are 3920 cm3 and 68 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 53.2 mm and 74.6 mm respectively. While when all three circle blastholes initiated with millisecond delay, the reasonable delay time is also 50 ms. At this time, the cutting volume and cutting depth of blasting model are 10705 cm3 and 118 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 51.0 mm and 81.7 mm respectively. The researches indicate that for millisecond blasting with multiturn blastholes, the reasonable blasting scheme is multiturn blastholes initiated in millisecond delay and the reasonable delay time is 50 ms.

Jan 1, 2015

By M. Leroux, S. R. Rao, J. A. Finch

"Poor Pb/Zn selectivity during Pb flotation in laboratory tests on a Mississippi Valley-type Pb/Zn ore was traced to a pH effect. In the pH range 9.5-11 sphalerite floated readily without copper activation. Compared to sphalerite flotation with copper activation this procedure gave equivalent selectivity but reduced flotation rate.Possible mechanisms of this sphalerite flotation without copper activation are discussed. Activation by Fe(OH) 2 is suggested, the Fe++ions being derived from superficial oxidation of pyrite in the ore.INTRODUCTIONGalena and sphalerite commonly occur together. The usual practice is to float galena first followed by the flotation of sphalerite after activation with copper (II) sulphate. If ores contain pyrite it is depressed by maintaining an alkaline pH (9- 10) and using NaCN as depressant.In flotation tests with a Pb/Zn ore from Polaris selective flotation of galena could not be achieved consistently as a considerable amount of sphalerite, even though unactivated, floated. A systematic study was carried out to determine the cause of this problem. This led to the unexpected finding that sphalerite floated in the alkaline pH range 9.5-11.0 without preactivation with Cuso 4 . This paper describes the results of this study and discusses a possible mechanism of the flotation of sphalerite."

Jan 1, 1987

By F. W. Gray

IN 1922, the writer communicated to the Institute a paper entitled The Development of the Coal Industry in Canada (1), which summarized the considerations set out in a series of papers (2) concerned with coal-mining in Canada which he had presented in 1920 and 1921. This paper contained a forecast by decades, commencing 1920, of Canadian coal production, importation, consumption, and exports, based on anticipated rate of population increase, and continuation of the gradual increase in the per capita rate of coal consumption in Canada that had taken place every year up to 1920. The following comparative statement brings our the differences between the forecast and actual experience:

Jan 1, 1936