Search Documents

By S. Spigarelli

The creep response of the AE44 magnesium alloy was studied by means of constant load creep tests carried out at 125 and 150°C, obtaining that at the latter temperature the minimum creep rate observed under an applied stress of 100 MPa was two orders of magnitude lower in the investigated alloy than in AM50. The minimum creep rate dependence on applied stress was described by a conventional power-law, e = Aon , where A was a temperature dependent parameter and n was the stress exponent, resulting in a n value close to 30, i.e. by far larger than those observed in commercial alloys with similar Al content. This large difference in creep response was attributed to the precipitation of rare earths (RE) intermetallic phases distributed in the grain boundary zone in form of an almost continuous network of dispersoids that were observed by means of scanning electron microscopy.

Jan 1, 2006

By W. Blum

Progress made in improving the creep resistance of Mg alloys is reviewed with the emphasis on microstructural interpretation. Experimental results on the increase of creep strain with time at constant stress a measured for limited times and strains are displayed in a transparent form as creep rate-strain diagrams from which the minimum creep rate stress is safely derived. In addition, data on the thermal stress component a derived from high-precision a-reduction tests are reported. Within a simple statistical dislocation model these data allow one to quantify the relation between dislocation velocity v and a . In combination with structure evolution laws this relation serves as a basis for modeling the creep rate. New alloys have distinctly higher creep resistance than AZ91 where precipitation hardening plays a minor role. This is due to hardening by intermetallic phases which may form a continuous skeleton along the grain boundaries (e.g. Ca-alloyed AZ91) and/or submicron-sized precipitates within the grains (MRI230D, Mg-Zn-Ca alloys).

Jan 1, 2006

By A. G. Eccles

"INTRODUCTIONWestern Mines' copper-lead-zinc operations are located in Strathcona Provincial Park, near the geographic centre of Vancouver Island. This park includes Buttle Lake, which flows into the Campbell River water system. The latter provides domestic water for the Town of Campbell River, approximately fifty-eight miles from the mine site.Operation of the concentrator commenced in December 1966, at which time the tailings were discharged into a small tailings pond near the plant. On May 8, 1967 Permit No. 185 was granted to the company, allowing discharge of the tailings, through a submerged outfall, to the bottom of Buttle Lake.Needless to say, the concept of operating a mine within a park, and the discharge of tailings into Buttle Lake generated considerable controversy. However, this has all but been eliminated over the years by the proven effectiveness of Western Mines' pollution control program. In 1973 this program was further upgraded with the addition of an alkaline chlorination plant. Effluent treatment by this method became necessary as a result of process modifications, and has been effective in maintaining the levels of characteristics in the tailings within the ever increasing pollution control requirements imposed on the industry."

Jan 1, 1977

By Donald V. Currie

"The Alberta and Northwest Chamber of Mines was founded in Edmonton, Alberta in 1935. The organization represented private sector mining explorers and developers in the province and north west Canada. The Chamber aided and abetted the establishment of the two territorial mining associations. Because of corporate human resource department creation by north of sixty mine operators, the Chamber refocused on Alberta and broadened its perspective to include activities beyond mining. In 1977 the name changed to the Alberta Chamber of resources. The slogan (in more modern terms vision, mandate, goal, etc) remains as Orderly Development of Canada's Resources.The sixty-three year reputation of the Chamber, built on volunteer rather than staff contribution, is the principal reason for any success. The key has truly been the reputation, not an image, as all activities have been solution oriented.This presentation provides insight into the structure and methodology applied by the organization, and reviews some of the successes and failures during the period 1985 to present. Examples discussed include:• Canada-Alberta Partnership on Minerals 1992-1995• Regional Upgrader Business Plan• National Oil Sands Task Force• Lakeland and Waterways Railway"

Jan 1, 1998

By Michael W. Russnak

Productivity and operating expenses are everything when it comes to judging how well your mine and company are doing. Stakeholders are always looking at these numbers and trying to understand if productivity is improving, if operating costs are trending downward and what you are basing your decisions on. o make improvements you first need to understand how you are performing. If you can?t get this basic information, you will never improve. You will not be able to make simple decisions related to maintenance, operations or production. Forget about planning, as you will only be guessing based on the numbers some stakeholder or your executive wants to see. The problem miners run into is not that the data doesn?t exist; it does, but typically it?s raw, it?s everywhere and its volume is huge. Today there is more on-board computing capability in shovels than we had on our desktops three years ago. Add other mobile equipment, plant systems and multiple OEM vendors to the equation and the challenge is daunting.

May 1, 2007

By D. Bouchard, J. Langlais, A. Lemieux, N. Andrade

A concerted effort between Akan International Limited and the National Research Council of Canada (NRC) has been initiated to develop a liquid-based slurrymaking process, dubbed SEED (Swirled Enthalpy Equilibration Device) for semi-solid forming. The technology is presently entering the industrial and commercial stages, and will be used by the first customers at the end of 2006. Semi-solid processing of aluminium alloys offers many advantages in fabricating economically near-net-shape parts of superior quality. The SEED process helps to overcome problems experienced with thixocasting and especially the high cost of feedstock. The SEED process involves two main steps: 1) heat extraction to achieve a desired liquid/solid mixture, and 2) drainage of an excess liquid to produce a self-supporting semi-solid slug that is formed under pressure. The heat transfer plays an important role (enthalpy equilibrium) during the manufacture of the semi-solid slurry and its analysis is briefly described. The semisolid material is obtained using different processing times and initial conditions. The impact on the solid fraction distribution and the morphological evolution of the microstructure is presented. The influence of the SEED processing parameters (slurry preparation) and the resulting mechanical properties for the alloy A356 are also reported.

Jan 1, 2006

By E. Uzun

"In this study, H2SO4 and HCl leaching behaviour of an ore sample containing 1.87% of Ni, obtained from the Karaçam (Eskisehir-Turkey) lateritic deposit that started operation recently was investigated. Acid concentration, temperature and reaction time were investigated as variables by comparative leaching tests and the optimum leaching conditions were selected on teh basis of Ni, Fe, Co and Mg behaviour. For H2SO4 leaching, optimum leach parameters were 95°C, a 12 normal H2SO4 concentration and 90 minutes of reaction time, and under these conditions Ni and Fe dissolutions were 97.6% and 95.4% respectively. On the other hand, 70°C, an 8 normal HCl concentration and a reaction time of 90 minutes were found to be the optimum parameters for HCl leaching, and Ni and Fe dissolutions found were 97.1% and 97.8%, respectively.INTRODUCTION Today, nickel and various nickel compounds are obtained from sulphide and lateritic nickel ores (Moskalyk & Alfantazi, 2002). Even though about 72% of the world's nickel reserves constitute lateritic ores, only about 42% of nickel is produced from these ores. The decrease in production from sulphide deposits, on the other hand, and increases in the use of nickel in the iron and steel, and battery production sectors, and especially the production of nickel cast irons in recent years, have accelerated the importance of making use of lateritic deposits (Luo et. al., 2010; Chang et. al., 2010). In the beneficiation of sulphide nickel ores, mostly pyrometallurgical methods are used. On the other hand, about 39% of lateritic ores are beneficiated by pyrometallurgical, and 61% are beneficiated by hydrometallurgical methods (USGS, 2009). In laterite beneficiation, the ore properties are of significance; that is to say, limonitic ores are eneficiated by high pressure acid leaching or via the Caron process, nontronitic ores are beneficiated by high pressure acid leaching or heat treatment (smelting), and ores containing serpentine by pyrometallurgical methods (Berezowsky, 2004; McDonald & Whittington, 2008a; Dreisinger et. al., 2015)."

Jan 1, 2017

By Nancy E. Wilk

In 2015, more than 1.2 million deaths annually were estimated to be caused by occupational risks (WHO, 2018). In 2021, this estimate increased with the publishing of the World Health Organization (WHO) and the International Labour Office (ILO) Joint Estimates of the Work-related Burden of Disease and Injury based on data from 2000 to 2016 (WHO/ILO, 2021). These global estimates reported that each year 1.9 million people die from exposure to occupational risk factors, 81% of these fatalities resulting from non-communicable, occupational diseases. WHO/ILO notes that the health-related risk factors with the largest number of attributable deaths were exposures to long working hours followed by workplace exposures to particulate matter, gases, and fumes. The health outcome with the greatest work-related burden of deaths was chronic obstructive pulmonary disease, followed by stroke and ischaemic heart disease. In considering the 2021 data published by WHO/ILO, it is likely that the estimates are low and underestimate the true burden of occupational disease and injury. In support of that position, more recently the ILO estimated that “2.3 million women and men around the world succumb to work-related accidents or diseases every year; this corresponds to over 6000 deaths every single day” (ILO, 2022).

Jan 1, 2023

By B. Lewis

Paper did not make deadline for printing

Jan 1, 1982

By H. T. Michels

Recent laboratory studies show that several bacteria, known to be human pathogens, die when they come in contact with copper and copper alloy surfaces. The amount of live bacteria drops by several orders of magnitude, to zero, on copper alloys in a few hours. In contrast, no reduction is seen in the concentration of live organisms on stainless steel during the six-hour test period. Aluminum painted and coated surfaces and plastics would show behavior similar to stainless steel and show no effect. Coatings and other surfaces claiming to be antimicrobial showed little to no effect. These results suggest the selection of copper alloys for surfaces exposed to human touch can materially assist in reducing the transmission of infectious organisms. In order to make antimicrobial claims in the United States, the approval of the US Environmental Protection Agency (EPA) is required. The EPA-required efficacy testing is described and the test results are summarized. It is anticipated, that once regulatory approval is obtained, that this will facilitate the introduction of antimicrobial copper alloys in hospitals, nursing homes and other healthcare facilities, as well as schools, and public buildings. Some of the application and barriers, to entry into the healthcare markets are mentioned.

Jan 1, 2007

By P. Shibley, P. R. Clarke

Since this was an interim report of the initial operation of a long term project it is not available for publication. It is expected when the project is completed a full report of the work will be published.

Jan 1, 1968

By B. W. Clyburn

"Coals from the Corporation's Lingan and No. 26 mines are classified as high-volatile A bituminous, with a very low inherent ash and containing a/l essential properties to provide metallurgical coal, with the exception of a high sulphur content. Only through proper cleaning at low specific gravity can the pyritic sulphur fraction of the coal be liberated to an extent where final sulphur meets coking standards. This first section of the paper deals with the operation of a Dutch State Mines heavy-media cyclone circuit to achieve an actual separation in the region of 1.30 specific gravity. A discussion of the parameter of control which must be applied along with an appraisal of the results obtained is included in the paper.IntroductionVery high fluidity and unusually low ash are the outstanding characteristics of coal from Devco's mines in the Harbour seam of the Sydney coal field.However, sulphur content, mainly pyritic, ranges from 1 to 2.5070. To obtain the low and consistent sulphur level required in metallurgical coking coals, preparation at low specific gravity is required .Metallurgical coke is used as the fuel in an iron blast furnace. Its sulphur content largely determines the quantity of slag required to remove it and therefore influences furnace productivity and unit costs.Typical data on the various coal properties of importance in the production of coke are included in Table I. Necessity of Low-Gravity SeparationThe design of any coal preparation plant requires the study of washability properties of the coal to be treated to determine the quantity and quality of coal produced at a given specific gravity along with the difficulty in accomplishing that separation.Their low ash content allows the important washability aspects of Harbour seam coals to be represented by sulphur! specific gravity curves (Fig. I). This particular example indicates that a yield of 54.5% is attained, at a sulphur content of 1.20%, for a perfect separating device operating with a 1.29 S.G. cut point.Material rejected from this separation still contains usable coal, which is recovered as middlings by separating at a higher gravity."

Jan 1, 1980

By Penny C. Stewart

Narrow vein underground stope design engineers in Australia have expressed significant interest in the requirements and methodology for developing site-specific stability charts. This is largely due to a concern that existing stope stability charts inadequately take into account factors influencing narrow vein stope stability, such as the effect of backfill abutments and the effect of in stope pillars. This paper presents conclusions from a comprehensive statistical examination of case history requirements for a site specific stability chart and critiques literature arguments for site-specific charts. A new statistical analysis technique and a large comprehensive stability database enabled the authors to quantify case history requirements and any site-specific effects the model exhibits. The analyses indicated that a reliable stable-failure boundary requires at least 150 case histories, of which a minimum of 10 percent should be unstable stope surfaces. Marginal site-specific effects were observed for the operating conditions captured within the database. The authors conclude that the apparent site-specific effects noted in previous literature are attributable to operating conditions inadequately represented in the database. Such operating conditions could induce erroneous stability predictions at any site, and are therefore not truly site-specific. Following from these conclusions, a strategy for taking into account operating conditions particularly relevant to narrow vein mining has been proposed. In particular, the development of a chart that accounts for the effect of backfill abutments on stope stability. Backfill abutment effects are particularly relevant to mechanised narrow vein mining methods such as modified Avoca. Collaboration from at least five sites is required to obtain access to relevant data and underground drives for geotechnical mapping. Preliminary estimations indicate that approximately three months fieldwork is required to meet case history requirements. CMS data in conjunction with 3-dimensional design software will be used to calculate equivalent linear overbreak/slough (ELOS). In contrast to stable, failure, major failure and caving categorical variables, ELOS is an objective and continuous stability variable and is therefore, more conducive to mathematical modelling.

Oct 1, 2001

By F. Rashchi, A. Ghahreman, J. Moghaddam, S. Karimi

"In this work, the kinetics of ferric-ferrous redox reaction on a passivated sphalerite electrode is studied by the application of chronoamperometry method in 0.5 mol L-1 H2SO4 solution. The electrochemical behaviour of ferric and ferrous couple was investigated on two sphalerite minerals acquired from two different geological regions (Iran and Canada). The carbon paste electrode (CPE) of sphalerite was initially prepared and passivated in 0.5 mol L-1 H2SO4 solution and after reaching the steady-state condition, ferric and ferrous sulfate solution was added. The registered current density differences between the current density of the passivated electrode and that of the electrode in the iron salts added solution were interpreted for kinetics of ferric-ferrous reduction-oxidation reaction. The equilibrium potential for ferric-ferrous couple on sphalerites surface was about 500 mV vs. Ag/AgCl. The exchange current density (i0) for ferric-ferrous redox reactions on the sphalerite samples had the same magnitude of 10–6 A cm–2. The electrochemical impedance spectroscopy (EIS) measurements at 550 mV vs. Ag/AgCl illustrated that sphalerite oxidation was controlled by two charge transfer process in both of Fe-free and Fe-containing solutions. The charge transfer resistance remarkably decreased when Fe salts added to the 0.5 mol L-1 H2SO4 solution, owing to the ferric-ferrous redox reactions being the predominant reactions on sphalerite surface.INTRODUCTION Direct atmospheric leaching processes for sphalerite concentrates are performed by reduction of an oxidant (e.g. ferric ion and oxygen) and oxidation of sphalerite to zinc ions. Oxygen could be an oxidizing agent as well, but the concentration of oxygen is very low in the solution. The role of ferric ions is predominate in this oxidation (Babu, Sahu, & Pandey, 2002). The oxidation reaction for sphalerite in the presence of ferric in can be presented as follows (Lampinen, Laari, & Turunen, 2015):"

Jan 1, 2017

By J. Dubinski

Poland is the ninth largest coal producer in the world and Coal Company is the largest Polish producer of this deposit yielding 51% of national production. Coal Company mines are located in the Upper Silesian Coal Basin. These are underground mines which operate in difficult geological conditions at great depths of up to 1200 m. One of the most common natural hazards in Polish mines are rockburst and seismic hazard impacting on surface infrastructure and habitants. In the assessment of the rockburst and seismic hazard methods of mining seismology play a leading role. This paper presents progress that was achieved in the last few years in the implementation of new seismic monitoring systems and seismic interpretation methods for the prevention of hazard deriving from seismicity induced by mining. This progress in assessment of rockburst hazard and impact of seismic activity on the surface infrastructure was achieved through close cooperation between the Coal Company and Central Mining Institute ? the country?s leading scientific institute in the field of mining seismology. New theoretical solutions are in the process of testing in mines of Coal Company where seismic monitoring systems are installed and controlled by well-qualified personnel. Some directions of further joint actions to increase the effectiveness of rockburst and seismic hazard assessment are presented as well.

Aug 1, 2013

By A. E. Gran

"QIT -Fer et Titane Inc. currently produces and markets four main products: a titania slag named SORELSLAG for the white pigment production, a high purity pig iron known as SOREL-METAL mainly used in the ductile iron casting industry, an ilmenite ore for blast furnace applications called SORELFLUX and high quality steel billets SORELSTEEL employed in the wire rod fabrication. Moreover , QIT also manufactures high quality iron and steel powders labeled ATOMET for the powder metallurgy industry through its wholly owned affiliate. Quebec Metal Powders Limited. The company operates. rock ilmenite mine near Havre St. Pierre and produces its slag and ferrous products from its metallurgical installations located in the Sorel/Tracy region. QIT. born in 1948 from a joint-venture between Kennecott Copper Corporation and New Jersey Zinc Company, was acquired from BP Minerals by RTZ Corporation PLC in 1989 and remains its wholly owned subsidiary ever since.lImenite is a mineral rich in both titanium and iron oxides. QIT's proprietary mineral enrichment and electric smelting processes permit the concentration of the ilmenite ore and the separation of its main constituents to produce a 80% TiO2, slag and a high purity molten iron which is further transformed into iron ingots (pigs), steel billets, iron and steel powders.QIT's ilmenite deposit is located in the Lake TIo-A1Iard area, 43 km inIand from Havre St. Pierre, a community on the north shore of the St. Lawrence River some 960 km from Montreal. The orebody, covering some 542 000 m2, consists primarily of coarse-grained ilmenite (FeO.TiO2) with disseminated fine lenses of hematite (Fe2O3). The worthless mineral (gangue) associated with ilmenite is mainly anorthosite, a complex silicate. QITs mining operations are carried out using conventional open pit methods in a 500 m by 600 m horse-shoe shaped mine with nine benches developed. Primary blasting is performed on a weekly basis during the mining season. Blasted ore is trucked to the crushing station to be broken down to 15 cm and 7.5 cm sizes, respectively, by means of a primary jaw crusher and a secondary cone crusher. Minus 7.S cm ilmenite is then loaded into hopper cars for the 43 km trip to the Havre St. Pierre terminal where it is stockpiled and reclaimed by under-ground conveyor chutes to a ship loading tower at the dock. The crushed ore is shipped to QIT's smelter located in Sorel in 40 000 tonne carriers from April to December."

Jan 1, 1995

By J. E. Dutrizac, Alba Sunyer

The factors affecting the precipitation of arsenic-free alunite (KAl3(SO4)2(OH)6) were investigated in a series of laboratory experiments. Although the amount of alunite precipitated increased with increasing retention time, temperature, solution pH and the concentrations of Al(SO4)1.5 or K2SO4, the composition of the products remained nearly constant. The preferred conditions identified for the precipitation of arsenic-free alunite were then used to assess the behaviour As(III) and As(V) during alunite precipitation at 98°C. Increasing additions of As(III), as NaAsO2 or As2O3, resulted in a slight increase in the amount of precipitate formed at pH 2.80. However, X-ray diffraction analysis showed all the precipitates to be alunite, and <0.2% As(III) was detected in the products. In contrast, increasing additions of As(V), as KH2AsO4 or As2O5, resulted in significant increases in the amount of precipitate formed at pH 2.80 or 3.00. Furthermore, the arsenate (AsO43-) contents of the precipitates increased up to 15%, and the sulphate contents decreased, as the As(V) concentration of the synthesis solution increased from 0 to 9 g/L. X-ray diffraction analysis of the products detected only alunite, but there was a progressive expansion of the alunite cell with increasing arsenate content. The implication is that arsenate substitutes for sulphate in the alunite structure. Preliminary observations on the environmental stability of the arsenate-bearing alunite using the TCLP protocol gave solubilities <0.4 mg/L from a precipitate containing 8.5% AsO4 and 7.8 mg/L from a product containing 19.5% AsO4. Thus, it appears that alunites containing less than -10% AsO4 would be an acceptable vehicle for the disposal of arsenic from hydrometallurgical processing solutions.

Jan 1, 2011

By R. V. Kumar, C. Schwandt, S. Subramanian, S. Sampath, S. Vimalnath

Waste waters and industrial effluents containing toxic heavy metals such as Pb, Hg, As and Cr, beyond permissible limits (0.1 ppm, 0.01 ppm, 0.02 ppm and 0.05 ppm, respectively) (WHO, 2011), pose serious threats to the ecosystem, when discharged into the environment. It thus becomes imperative to monitor the concentration of the toxic heavy metals and treat them before discharging. In this study with the above objective in mind, a microbial sensor has been developed using P. aeruginosa cells drop coated onto a carbon paste electrode (CPE) for the detection of Pb(II) ions in aqueous solutions. Detailed biosorption experiments confirmed that complete bioremoval of lead could be achieved using P. aeruginosa cells under optimum conditions of pH and biomass loading. For the electro-analytical determination, the Pb(II) ions were initially preconcentrated on the P. aeruginosa modified CPE, reduced and then anodically detected with oxidation of Pb0 using differential pulse anodic stripping voltammetry (DPASV) technique. All the experiments were carried out in the presence of 0.1 M sodium acetate buffer and KNO3 as background electrolyte. The parameters namely pH, scan rate, biomass loading, deposition potential, deposition time and concentration of Pb(II) ions were optimized for the biomass modified CPE, to obtain maximum voltammetric response. Under the optimized conditions of pH 5.6, scan rate of 0.008 V/s, biomass content of 1.7–1.8×109 cells/mL, deposition potential of –1.2 V, and deposition time of 500 s, the developed microbial sensor showed a linear response for the peak current between 0.5×10-5 M and 1×10-8 M of Pb(II) ions with the R2 value of 0.9979. The lowest limit of detection (LLOD) was determined as 2.4×10-7M of Pb(II) ions (0.05 ppm). The redox mechanisms of Pb(II) ions on the P. aeruginosa modified CPE surface are discussed.

Jan 1, 2016

By Robert B. Parsons

"A t last the legal red tape which has tied up flow-through share financing has been cut. New rules effective for deals signed after 1986 simplify flow-through financing by removing the necessity f or cumbersome agency relationships. But there is no free lunch-the new rules require increased government reporting. And beware federal tax reform promises to have a good look at the new flow-through share rules. IntroductionFlow-through shares have always worked better in theory then reality as an effective financing tool. The concept is straightforward: a transfer of risks, tax deductions, and potential returns. But the mechanics of the old flow-through rules made the transfer of risk impractical to impossible by placing the responsibility for incurring Canadian exploration expense (CEE) on investors. The new rules are significantly more realistic, shifting that responsibility to the issuing corporation. However, every silver lining must have a few clouds around it. In the case of the new flow-through rules, the more obvious negatives are increased reporting requirements and reductions in CEE eligible for flow-through by amounts of assistance received. The new rules are effective for deals signed after 1986, however, so a few old-style deals are still around. Practical Difficulties with Old RulesThe old rules which applied to investments in flow-through shares were structured so as to make it the responsibility of the investor, rather than the issuing corporation, to perform the Canadian exploration expense for flow-through. Since most investors had neither the expertise nor the inclination to incur the CEE, this requirement necessitated the use of cumbersome arrangements whereby the investors would appoint an agent (usually the issuing corporation) to incur CEE on their behalf. Although the issuing corporation might consequently be the party which actually spends the flow-through share funds on CEE, the awkward legal structure of such an arrangement made the investor the ""principal"" incurring the CEE. As such, the requirements of the old rules were met and the investors could receive their flow-through share s."

Jan 1, 1987

By W. T. Martson

ABSTRACT Sooner or later, every producing mine faces the question of fill. This paper invites consideration of mill tailings as an economical, efficient, and quantitatively adequate source of such fill. Some of the advantages, disadvantages, methods of utilization, and methods of treating mill tailings for sand recovery are covered. ADVANTAGES AND DISADVANTAGES OF SAND FILL DISREGARDING economic com-promise, that material which supports the greatest applied load with the least compression is the best choice for fill. Table I, reproduced from U. S. Bureau of Mines Bulletin 60, is offered as evidence of the adequacy of hydraulically placed sand. Table II gives the results of tests made in an effort to determine the reason for the difference between load hearing qualities of dry-placed and hydraulically-placed sand. From these, it would appear that hydraulic placing gives a denser initial packing, with corresponding higher, and faster development of, load bearing qualities. Assuming this to be true, then if sand from mill tailings can be placed underground economically, it is the superior fill material. Table III summarizes cost data available. The most cursory glance through the available references (2, 5, 6, 7, 8, 9) will show .that the major benefit from the adoption of sand fill is a decrease in the non-productive fill ?cycle of a working place. This, it is estimated, increases the output of an individual stope by from 25 to 50 per cent. The advantage of reducing the number of required working places for a constant daily production is obvious.

Jan 1, 1951