Search Documents

The object of this paper is not to describe any particular type of engine in close technical detail but rather to give a general picture of past and present practice in this important section of the industry. The subject involves the study of almost 600 years of coal mining history which has fluctuated from stagnation to extremely rapid progress.Up to the year 1300, coal was obtained from outcrops and exposed beds, but this easily worked source soon gave out, so by that time shafts had to be sunk to the coal seams, and coal mining proper commenced its career.These early shafts were very shallow, and winding equipment was not a matter for much concern. Raising coal was generally achieved by human labour, which was called "coal bearing." Coal was loaded into baskets. strapped to a man's back, and carried from the underground workings to the pit bottom. The unfortunate individual then climbed ladders to the top of the shaft, unloaded the basket, and descended the shaft for the next load. Men, women and even children, were employed as the mine expanded, and were generally bound to the colliery for life, performing daily work which would now be regarded as slavery. This primitive method of raising coal to the surface was slow, inefficient and highly dangerous, yet for want of a better method it continued until in 1602 it isrecorded as having been abolished in Wales, one of England's great coal districts. It was not until 100 years later, however, that it was abolished in the northern coalfields, and the colliers were freed forever from their dreadful life.WINDLASSThe first step towards winding coal was the introduction of the windlass. This was similar to the common windlass used over a well, and was operated by man power. The...

Jan 1, 1945

It is a commonplace of our industry that prices of most minerals have been historically weak during the 1980s. The International Monetary Fund's index of prices of metals fell 25 per cent between 1980 and 1982, rose slightly in 1983, and has since fallen further. In December last year it was 37 per cent below its 1980 average. The few temporary exceptions to the mineral industry's malaise highlight the excess capacity, which largely explains the weakness of prices. The industry has painfully come to recognise that more satisfactory prices will not be restored until supply capability and demand move back into better balance. Mine capacity was installed in the expectation of much faster growth of demand than has occurred. For a variety of reasons mine and plant closures have been insufficient to restore equilibrium to the market-place. The industry may, therefore, have to resign itself to continued weak prices for some years more, at least by the yardstick of the 1970s. Growth rates of demand have slackened off in line with economic activity, and in response to continuing substitution and technological improvements. To the extent that the recent weakness of oil prices stimulates the industrial countries' activity, demand for non-fuel minerals may grow faster than most forecasters now predict. It is, however, much too early to say how long the weaker oil prices will persist, and even more difficult to estimate their probable effects. In typical post-war business cycles the usual response to recession was to batten down the hatches, and ride out the storm. Sooner or later, and probably sooner, demand resumed its previous trend path, and prices recovered. The market, in effect, bailed mines out of trouble; the more efficient could make attractive pre-tax profits whilst even the poor to mediocre could earn a satisfactory living. Prices rose at least as fast as general inflation, and in the early 1970s much faster. In retrospect those price rises of the early 1970s were historically abnormal but they did not appear so in the prevailing inflationary climate of the time. When the market failed in the early 1980s many of the hardest hit companies looked for scapegoats.

Jan 1, 1986

Pyrrhotite is pyrophoric when in a finely divided form. The problems of disposing of large quantities of finely divided pyrrhotite separated out by metallurgical processing from ore are formidable. In the case of an underground mine, a solution to the problem of disposal is to place the pyrrhotite in the stoped out areas and seal from any air supply. Further, the pyrrhotite could be diluted with tailings which would reduce the possibility of combust- ion. Several enquiries to various centres and authorities have shown that the products of the slow oxidation of pyrrhotite with moisture present can cement an inert matrix into a stable fill similar in physical prop- erties to fill stabilised with Portland cement. Stabilised fill can be used to advan tage with a suitable mining method to provide high recovery. The investigation demonstrated that air and 15% w/w water must be present for the fill to harden and that the sizing of the particles is a critical factor in drainage of a hydraul- ically placed fill and subsequent even harden- ing of the fill in a stope. With the materials used in the experiments in which the - 51 micron component of the tailings had been dis- carded, an optimum mix was found to contain 4:1 tailings/slag ratio and an overall pyrr hotite concentration of 8% (all proportion by weight). Approximately 34 days after drain- age to 15% moisture in natural air flow condit- ions, an unconfined compressive strength of 1.862 MPa was attained. A subsequent experi- ment was conducted with a sample of optimum mix in a pipe one metre long in forced air flow conditions. At a superficial velocity of 3.Om per hour the mix required 155 hours to harden to 1.862 MPa after drainage to 15% w/w moisture content. The pressure drop bet- ween the top and bottom of the mix in the pipe remained constant at 9 KPa/metre length. This result suggests that forced air flow conditions will increase the rate of hardening. No dangerous effluents were detected in the course of the experiments which could affect mine equipment or personnel.

Jan 1, 1973

Structure is the most important control on the location of hematite deposits in the Hamersley Province in the Pilbara region of Western Australia. Unravelling the structural history of mineralised areas, however, is complex because the Province underwent three orogenic events, and three regional extension events followed the main episodes of compression. Steeply E to ENE dipping normal faults immediately predated deposition of the Beasley Quartzite of the lower Wyloo Group after the Ophthalmian Orogeny. Steeply NE and SW-S dipping normal faults predated deposition of the McGrath formation of the middle Wyloo Group, following the Panhandle Orogeny. The resulting interpreted rift was subsequently reactivated and tilted during the Capricorn Orogeny. Late NE trending normal faults are confined to the eastern half of the Province. High-grade hematite deposits occur in rocks that range from intensely folded (Mt Whaleback, Giles Mini) to rocks with less, or only little deformation (Paraburdoo, Channar), suggesting that folding had at best limited influence on ore genesis. In contrast, extensional normal faults are always associated with high-grade hematite deposits, and in particular faults that link the underlying dolomites of the Wittenoom Formation with the overlying iron formation, thus providing a pathway for mineralising alkaline fluids.

Jan 1, 2005

By Dickson B. L

Groundwater geochemistry is controlled by chemical interactions with aquifer rocks, and offers a powerful geochemical exploration technique for locating concealed mineral- isation. Techniques are applied for identifying constituents of aquifers using the compositions of their groundwaters, collected from the surface through drill holes, water bores or springs. Even slowly moving groundwaters have passed through large volumes of rocks which surround any sample site. Products from these rock-water contacts modify the groundwater. By relating water composition to the minerals from which the dissolved species may have been derived, geochemical exploration information is obtained for a significantly larger zone than is represented by drill hole rock samples. In this paper we describe some solution chemical tech- niques we are applying in mineral exploration, particularly in areas of Australia where ground- waters are highly saline and contain enhanced concentrations of trace metals. EQUILIBRIUM MODELS FOR SALINE GROUNDWATERS Central to our technique is the assumption that in low rainfall regions, aquifer rocks and contained groundwaters are in chemical equili- brium. Solubility calculations then allow us to predict upper limits to the soluble products of groundwater interaction with aquifer rocks and to identify minerals with which the groundwater is saturated. Whilst equilibrium calculations require input of concentrations of all dissolved species, they are actually based on "activity" of dissolved species rather than the analysed concentrations. Unless waters have very low ionic strengths (a measure of total dissolved solids), activity of a solute is not equal to its analytical concentration but equals concentration multiplied by an "activity coefficent". Several methods exist for calculating mineral solubilities. The ion-association model, commonly used in programs such as WATEQ (Truesdell and Jones, 1974) and later deriv- atives such as MINTEQ, assume the formation of complex ions such as MgSO4(0), CaCl+, which are described by formation constants. Activity coefficients are obtained by the extended Debye

Jan 1, 1988

By Kohra A, Shoji S

The amount of copper production by flash smelting process occupies about 17% (equivalent to 1.4 million t/year) of total free world production. In Japan, 650,000 tons of copper is produced annually by flash smelting. This is 65% of the gross copper production of Japan. To reinforce pollution control, promote energy saving, and enhance production efficiency by increasing the size of furnaces, conventional blast furnaces and reverberatory furnaces are being replaced with the flash smelters worldwide. The Ashio Smelter started copper production in 1884 and developed in association with the Ashio mine. In those days, the Ashio smelter produced copper by using the blast furnace process designed for the high-grade ore from the copper mine. At that time, this process was specialized in Japan. In 1956, for the first time in Japan, the Ashio Smelter introduced the flash smelting process developed by Outokumpu Oy of Finland (it is suitable for treating the copper concentrate, producing sulfuric acid and improving production efficiency). The flash furnace in Ashio, the first ever in Japan, had a capacity of 230 t/day for copper concentrate and was operated up to 1962. During this period, various operational troubles were solved, and further improvements were made; and, in 1962, a Furukawa-type flash smelting furnace was completed in Ashio. This improved version of a flash furnace had a capacity of 450 t/day. There was one flash furnace and one waste heat boiler, which were arranged in a unique pattern for that time. This furnace may be said to be the prototype of the present flash smelting process in the world.

Jan 1, 1987

An image analysis system has been built which automatically digitizes camera input of rock fragments, analyses the digitised data to determine the sizes and shapes of the rock fragments, and outputs the analysed data to a printer in the form of a histogram or a scatter chart. The high speed of such a system allows for direct collection of data from material thrown into the air by blasting, material travelling on a conveyor belt, and material free-falling on to a stock-pile or into or out of a rock-crusher. Data on the blasted, un-crushed material provides information on changes in the lithology and structure of the rock face as it is quarried or mined: flatter fragments may represent approach to a brittle, unstable shear zone, or a change from sandstone to shale; so that the informa- tion reflects the effect on the sizes and shapes of the fragments by the blasting process and/or by the rock structure. The size and shape distributions of rock fragments produced during blasting and during processing may now be continuously monitored. Such detailed analysis of the results of fragmentation is labour-intensive and expensive when the size and shape distributions are obtained manually, but is cheap and efficient when using this image analysis system. Such a system will enable the results of blasting, quarrying, mining and crushing to be cheaply analysed and correlated with current and changing indus- trial practice so leading the way to increased productivity.

Jan 1, 1988

By M P. Schwarz

In recent years, computational fluid dynamic (CFD) modelling of mechanically stirred flotation cells has been used to study the complexity of the flow within the cells. In CFD modelling, the flotation cell is discretised into individual finite volumes where local values of flow properties are calculated. The flotation effect is studied as three subprocesses including collision, attachment and detachment. In the present work, these subprocesses are modelled in a laboratory flotation cell. The flotation kinetics involving a population balance for particles in a semi-batch process has been developed. From turbulent collision models, the local rates of bubble-particle encounters have been estimated from the local turbulent velocities. The probabilities of collision, adhesion and stabilisation have been calculated at each location in the flotation cell. The net rate of attachment, after accounting for detachments, has been used in the kinetic model involving transient CFD simulations with removal of bubble-particle aggregates to the froth layer. Comparison of the predicted fraction of particles remaining in the cell and the fraction of free particles to the total number of particles remaining in the cell indicates that the particle recovery rate to the pulp-froth interface is much slower than the net attachment rates. For the case studied, the results indicate that the bubbles are loaded with particles quite quickly, and that the bubble surface area flux is the limiting factor in the recovery rate at the froth interface. This explains why the relationship between flotation rate and bubble surface area flux is generally used as a criterion for designing flotation cells. The predicted flotation rate constants also indicate that fine and large particles do not float as well as intermediate sized particles of 120 - 240 ¦m range. This is consistent with the flotation recovery generally observed in flotation practice. The magnitude of the flotation rate constants obtained by CFD modelling indicates that transport rates of the bubble-particle aggregates to the froth layer contribute quite significantly to the overall flotation rate and this is likely to be the case especially in plant-scale equipment.

Jan 1, 2005

By Roxborough F. F

The ability of the Australian minerals industry to successfully manage the changes and challenges that face it in the 21st century depends ultimately on the quality of its human resources. Mining engineers have a vital role in this regard. The education and training that universities are currently giving to mining engineers is under challenge and needs to be reassessed in the light of industry directions for the 21st century. At one extreme is a push for a `finished product' graduate, up and running in `the flavour of the month' issues. At the other extreme are moves to reduce face-to-face university teaching hours and return to the time honoured university concept of `reading' for a degree. The lessons of Mourn make it apparent that neither approach is appropriate to the industry's future needs (Windridge, 1996). Basic knowledge gets rusty with time and new skills need to be learned. In order to conduct mining operations safely, productively and competitively, mining engineers must now accept the need to be prepared for continuing professional development as a career imperative. The concept of being professionally or statutorily qualified for life is no longer valid. This calls into question the purpose, content, structure and mode of delivery of university courses, all of which need to engender the principle and facilitate the cause of continuing professional development. This paper presents a model which aims to deliver a quality assured university education for mining engineers for the 21st century at undergraduate, postgraduate and professional level. The model extends beyond traditional university boundaries to match industry requirements to international best practice. It is based on collaborative alliances and innovative presentation modes which will provide industry access to undergraduate and postgraduate course elements presented by a broad range of national and international academic and industry authorities. It offers the prospect for preserving the best of university ideals in higher education, for developing and maintaining programs of direct relevance to industry needs and for a structured involvement in the continuing professional development of mining engineers.

Jan 1, 1997

Petroleum exploration in the Australian arid zone has been proceeding at an ever-increasing pace, subject to financial fluctuations, since the 1960's. The impacts of petroleum exploration in the arid zone are less than they would be for corresponding operations in. e.g. a forest area: in this context, Australia is fortunate in that its major petroleum producing (and prospective) , basins are offshore or in the arid zone. In addition. the other major sources of impact in the Austrlian arid zone, namely pastoralism, tourism, and rabbits, tend to be concentrated around areas of particular conservation significance, whereas petroleum exploration is not. Despite this, the cumulative impacts of exploration are sufficient to have caused concern to government regulatory authorities and some sectors of the general public. Exploration is now subject to a range of environmental constraints with various degrees of legal enforceability. To enable exploration to continue without public opposition, the industry, and government agencies charged with regulating or supervising it, must demonstrate that the net benefits of exploration exceed net costs, including environmental costs. One particularly simple and cost-effective technique for increasing the net benefit/cost ratio of exploration is to reduce the net environmental costs by minimising and mitigating the impacts, both primary and secondary, of seismic acqisition. This is best achieved by a combination of preventive and restorative techniques: careful line positioning and low-impact (or zero) line clearance, coupled with simple rehabilitation of bladed lines. Line clearance without bulldozer blading - e.g. by rolling or simply pegging and trafficking, perhaps with tracked rather than rubber-tyred vibroseis - is one promising approach currently coming into use. Rehabilitation by grading soil banks ("windrows") back on to bladed tracks, though not yet in widespread use, has proved very successful in the limited areas where it has been applied to date.

Jan 1, 1987

By P J. Scales, D Boger

Technological advancements in mineral processing have increased the feasibility of refining low-grade ores. Because of this progression and continual depletion of high-grade ore deposits, much larger volumes of waste material are produced. At the same time, increasing environmental legislation and cost competitiveness dictate that these wastes be disposed of in a manner that is both environmentally acceptable and economically viable. To achieve these criteria, many mineral processing industries are dewatering waste streams in order to reduce the volume of tailings and increase water and reagent recovery. The subsequent dry disposal of these highly concentrated mineral tailings requires a thorough understanding of the effects of dewatering on the flow characteristics. Dry disposal represents a paradigm shift in engineering. The tailings are engineered to suit the disposal requirements, as opposed to engineering a facility to accommodate the tailings. It is therefore important to understand how the material properties and operational parameters can be modified to produce the desired tailings flow and deposition characteristics. As concentrated suspensions usually exhibit non-Newtonian behaviour, determination of the disposal plant operating conditions requires a thorough understanding of the rheological characteristics of the material. The implementation and optimisation of dry disposal methods involves three concurrent and interdependent rheological studies to determine:the concentration required to achieve the optimum spreading and drying characteristics of the tailings once deposited; the optimum conditions for pipeline transport; and the feasibility of dewatering the slurry to the required concentration. The paper presents an overview of the issues pertinent to management of the flow properties and processing of dewatered waste streams.

Jan 1, 2002

By Davey KJ

Complex sulphide ores are characterised by complex texture of the valuable minerals. Any assessment of the performance of differential flotation circuits treating such ore should include analysis of the effects of poor liberation of the valuable minerals. Selected samples were taken from balanced size by size surveys of the flotation section of a concentrator treating an ore body containing fine grained galena and sphalerite in a matrix of iron sulphides which is mostly pyrite. liberation measurements were made using the QEM*SEM system on four or seven size fractions. The measurements indicated that less than 40 per cent of the galena and less than 60 per cent of the sphalerite in the flotation feed was liberated. The final concentrates were largely composed of composites of valuable minerals and iron sulphide however there was a small but significant fraction of liberated iron sulphide. Using the sized mineral flows obtained from the original balances and the liberation measurements, a satisfactory liberation balance was obtained. This enabled the effect of liberation on the flotation performance to be examined; not only for the entire circuit but also in the rougher, scavenger and cleaning sections. In the zinc circuit the effect of a regrind mill could be assessed. Recovery of galena in the lead circuit was limited by the recovery of composite lead particles. Recovery of liberated galena exceeded 95 per cent in all size fractions while the recovery of composite galena exceeded 85 per cent below 38 ¦m but fell sharply above 38 ¦m. Examination of the behaviour of the liberated and composite galena in the various sections of the lead flotation circuit revealed high recoveries of both liberated and composite galena particles in the roughing and scavenging sections but very low recoveries in the final two cleaning stages. Similar trends to those observed in the lead circuit applied in the zinc circuit although the performance of the liberated sphalerite also fell off at sizes greater than 38 pm in this case. Thus the zinc recovery was limited by the flotation of both the liberated and the composite sphalerite. The effect of regrinding was to increase the recovery of sphalerite mainly by reducing the amounts of sphalerite in less liberated sizes rather than by increasing the liberation of the sphalerite within a given size Fraction.

Jan 1, 1993

By C J. Berry, P H. Briggs

Assessment of metal mobility, acid rock drainage production, and toxic effects from weathering of mineralised materials (ie mine-waste piles and outcropping alteration/ore zones) is key in evaluating and mitigating metal mining sites. Many metal- and acid-generating materials at these sites are sulfur minerals (sulfides to sulfates) with differing reactivities, weathering characteristics and metal contents. Our working hypothesis predicts that data on the types and quantities of sulfur minerals, coupled with comparison of their sulfur isotopic compositions to that of aqueous sulfate in the surrounding environment, can be used to evaluate primary pathways of weathering reactions at mining sites. We developed a sequential extraction scheme to separate the phases of sulfur in mineralised materials. Operationally defined phases, including monosulfides, disulfides, elemental sulfur, water-soluble sulfo-salts, acid-soluble sulfates, and resistant sulfate phases such as barite, are quantified gravimetrically and/or instrumentally. Several sets of experiments were designed to test the effectiveness of this extraction scheme. First, a variety of ore sulfides diluted in an inert matrix was analysed with the scheme. Results showed that molybdenite and arsenic-bearing sulfides do not behave as predicted from just their sulfur oxidation states, indicating that samples containing these minerals need special treatment for complete phase recovery. Second, a natural mine-waste composite standard was analysed by the scheme. The sum of the phases was equal to the total sulfur concentration analysed independently. Each phase had a similar, but distinct sulfur isotopic composition. The results were verified with a laboratory prepared æproxyÆ having the same mineralogical composition as the standard, but with each phase having a very different sulfur isotopic composition. The sulfur isotopic compositions of the recovered phases from the æproxyÆ showed that the scheme effectively separated the sulfur with only minor cross contamination of phases. The speciation and isotopic analyses were applied to both mine-waste piles and naturally occurring alteration zones at nine mine sites. A case study from one site comparing the sulfur isotopic composition of minerals in an alteration zone and dissolved sulfate in proximal streams is presented. This case study shows the application of our data to differentiating sources of sulfate in the surrounding environment.

Jan 1, 2003

By D Craw

Middle and Late Cenozoic fluvial conglomerates and gravel in northeastern Southland record the transport of alluvial gold from Central Otago into Southland, and subsequent reworking and concentration of this gold into economic placer deposits. A corridor of geochemically distinctive, Hg-free gold derived ultimately from veins in Torlesse Terrane schist in Otago extends through the Caples Terrane and into Southland. The initial repository in Southland was fluvial sediment of the East Southland Group, specifically weakly auriferous, quartzose delta plain strata of the Gore Lignite Measures (GLM), a downstream equivalent of Dunstan Formation in Central Otago. Miocene uplift along the northwest trending Old Man Range beheaded the parent river system, isolating GLM from its Central Otago source area and establishing the proto-Waikaia River system. Rising topography between Otago and Southland increased fluvial gradients, and initiated erosion of cover strata and a sequence of tectonically induced gold recycling events. Auriferous GLM were recycled from the hinterland into broad braided fluvial channel and floodplain deposits of the Waikaia Group (new), specifically the highly auriferous Waikaka Quartz Gravels and equivalent Waimumu Quartz Gravels downstream (WQG), superimposing more proximal depositional environments over parts of the former GLM delta plain. WQG were deformed, and locally cannibalised during the later stages of their deposition by reverse movement on north-northeast trending faults of the Dunsdale System (NW side up). Increased tempo of uplift in the hinterland (Old Man, Garvie, Umbrella, and Blue Mountain Ranges) in the Pliocene and early Quaternary resulted in further reworking of GLM and WkQG from the hinterland as well as basement erosion. Progressively more basement-rich detritus was deposited as a locally auriferous piedmont (Gore Piedmont Gravels - GPG) over earlier channel and delta plain (GLM, WQG) strata, extending from the Blue Mountains to Waikaia, and southward through the Gore Gap to beyond Mataura. Southward propagation of the north-northeast trending ranges, local warping, and uplift of the Murihiku Terrane in Pliocene and Quaternary progressively deflected GPG fluvial systems and ultimately constrained them to the present valleys. Pre-existing auriferous strata (GLM, WQG, GPG) were reworked and deposited with or without basement detritus as these fluvial systems migrated toward their present positions. Auriferous remnants of these transitional deposits are preserved in local structural depressions on the uplifted blocks that deflected the systems (eg King Solomon Mine), and on locally abandoned floodplain segments on the lowlands (Pebbly Hills-Gore Gap). The present drainage has continued to incise and cannibalise its own and earlier deposits during late Pleistocene-Recent uplift to form confined channel placers within the present valleys.

Jan 1, 2002

A static equilibrium mathematical model of the lead,flotation circuit at The Zinc Corporation Limited is developed to permit the feasibility of applying computer control techniques to be studied. The model is based on the relationship between the cumulative recovery of a mineral species R from n flotation cells or assemblies in a unit given asR = M(1-(1 - p)?)where M is the maximum possible: recovery and p is the probability of flotation for the particular mineral.The verification of this relationship by data from pilot plant cell-to-cell and plant open flow flotation units shows that these systems behave as if the probability p is constant for each cell or assembly of anyone unit. It is also concluded from this study that mineral recovery is independent of the head assay. Two consequences of this probability relationship, are demonstrated.1. The total recovery from an open flow unit is enhanced by increasing the number of flotation assemblies but maintaining a constant flotation time and total air addition.2. The rougher and scavenger capacity required to recover a bulk lead-zinc concentrate is approximately half that used for selective flotation.The static equilibrium model is derived by solving a series, of mass balance equations which incorporate the recovery-probability relationship for each type of flotation unit. It is used to calculate the complete metallurgy of the circuit for any arrangement of cells knowing only the plant feed assays and the probabilities of flotation for the three mineral types, galena, marmatite, and gangue for rougher, scavenger, and cleaner flotation. The high degree of prediction obtained is demonstrated by comparison with plant results.Pulp flowrate is the principal variable affecting the accuracy of the present model. Work is in progress to establish this effect and permit the derivation of a dynamic model. Even so, the static model is valuable in its present form for the analysis and design of circuits, and optimisation studies using computer services have been conducted.

Jan 1, 1964

Mineral exploration and development can have a significant impact on the environment and local communities, in some circumstances extending well beyond the mine site. Poor environmental performance and consequent social impacts by some companies have affected the reputation of the whole industry to the extent that the principal public concern about mining is its impact on the environment. This is consistent with public attitudes about other major natural resource sectors such as forestry and commercial fishing. Traditionally the community has relied on governments to set the benchmark for acceptable environmental and social performance through establishing and revising regulations governing the mining industry. This however assumes that regulations keep pace with community expectations. It also does not take into account those circumstances where governments can have conflicting roles as both watchdog and project partner. Government regulations and industry self-regulation are not in of themselves sufficient for the minerals sector to demonstrate that it has adequately addressed environmental and social issues associated with the sector. For the minerals sector to improve its reputation it must first improve its environmental and social performance. To do this requires the sector to operate to acceptable standards of environmental and social performance and for the sector to be able to credibly communicate this to its stakeholders such as investors, non-government organisations (NGOs), customers, staff, regulators and local communities. Independent third party certification of environmental and social performance (æcertificationÆ), already operational in forest and fisheries management, is proposed as a mechanism to enable the minerals sector to achieve this. World Wide Fund for Nature (WWF) and industry partners will be collaborating in a project to ascertain the applicability of æcertificationÆ to the minerals sector. A number of economic, social and environmental benefits are identified that could accrue should mining companies be able to differentiate themselves on the basis of environmental and social performance, an attribute evident in æcertificationÆ schemes. External audiences are seeking increasing levels of information and data on environmental and social performance of mining companies, be it local communities, investors, financial institutions or NGOs. Environmental and social reporting should be a key communications device that stakeholders can rely on as a reliable, credible source of information on environmental and social performance. WWFÆs contribution to the debate about environmental and social reporting has been to develop a process to assess the quality of environmental and social reports against reporting ingredients which WWF believe are important if a report is to be an accurate reflection of the reporting entitiesÆ environmental and social performance.

Jan 1, 2002

By A M. Myrvang, B Nøst, N Q. Trinh, I S. B Bergh

The iron ore producer Rana Gruber AS is situated in northern Norway just below the Arctic Circle, and has been producing hematite and magnetite concentrates for more than 60 years. Since the late 1990s, the major part of the production comes from a sublevel stoping underground operation after many years of open pit mining. Despite moderate mining depth, the operations have experienced considerable rock stress problems due to quite high tectonic, horizontal stresses. To manage the problems, comprehensive rock mechanics investigations have been carried out by SINTEF, a major contract research organisation. This has included in situ rock stress measurements, laboratory investigations and numerical modelling. Based on this and practical experience, satisfactory design of vertical and horizontal pillars was achieved. At depth, the ore width increases from 30–40?m to more than 100?m. This, together with a major planned increase in production, called for a change of the mining method. After thorough investigations and considerations, it was decided to change to sublevel caving, very much like the LKAB system. The development of the new system has been closely followed up by rock mechanics measures, including 3D numerical modelling and comprehensive monitoring of deformations and rock stress changes. To achieve a satisfactory caving of the hanging wall, all vertical and horizontal pillars in the sublevel stoping area had to be removed. This has been a challenging task, and the development of the caving has been slow until recently. However, now the caving develops satisfactorily.CITATION:Bergh, I S B, Trinh, N Q, Myrvang, A M and Nøst, B, 2014. From sublevel stoping to sublevel caving at Rana Gruber, Norway – rock mechanical aspects, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 323–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By S Harvey

An inrush of water or mud into an underground mine, or sudden subsidence above mining voids represent low probability but high impact risks in underground mining. About two such incidents involving multiple fatalities or loss of production are reported each year worldwide. On average, Australia experiences one such incident every three to four years. This paper reports the development of a Standard that is intended to eliminate fatalities due to inrushes and subsidence.

Jan 1, 1998

By Yu AB, Azahari HL

Indonesia has the largest coal reserves in the south-east Asian region. According to estimates from the World Energy Confer- ence, it has reserves of 18 billion mt lignite, 4.4 billion mt sub-bituminous coal and 774 million mt bituminous coal (Wyllie,1988). In recent years, substitution of coal for oil in power plants has been the goal of the Indonesian government since proven deposits of coal are about five times as large as national hydrocarbon reserves and most of Indonesia's power stations are still oil fired. Recently a coal fired power plant has been built in Java Barat, which will have a full capacity of about 3000 MW. It is intended to supply coal for this power plant from Bukit Asam mining area (South Sumatra). Coals from Bukit Asam - which are of the lignite or brown coal type - usually contain considerable moisture . It should be noted that reference to moisture in coal pertains to the total moisture content. This is comprised of what is commonly termed as equilibrium moisture and surface moisture. Surface moisture typically affects combustion process as well as pulveriser performance since it possibly influences the relative ease with which coal may be ground. In practice, the surface moisture produces agglomeration of the fines in the pulverising zone and reduces pulveriser drying capacity because of the inability to remove the fines as quickly as they are produced. This agglomeration has also the same effect as coarse coal during the combustion process because the surface area available for the chemical reaction is reduced, hence the combustion efficiency is also reduced. The influence of the moisture of some coals on their grindability (Hardgrove Grindability Index) has been previously correlated by several authors; some of them will be mentioned later. Those correlations, however, could not be immediately applied to any coal since it is still believed that there are other factors which influence the grindability of the coal, such as type and rank of the coal. The relationship between coal moisture content and its grindability has been investigated by Ellmann and Belter (1955). It was found that, for North Dakota lignites, the grindability varied as the moisture content changed. In Britain, Fitton, Hughes and Hurley (1957) stated that, for Bilsthorpe coal, over a wide range of free moisture content (from air-dried to about 30 per cent moisture), the Hardgrove Grindability Index (HGI) remains virtually unchanged. In addition to that, it was suggested that it would be slightly advantageous to dry the coal below its air-dried moisture content (at temperature ¦ 100¦C) to increase the ease with which coal could be ground, especially for low-volatile coal and high-volatile non-caking coal. Furthermore, it was also concluded that a broad relationship appeared between coal rank and Grindability.

Jan 1, 1993

By Miller D. R

The mineral exploration and extraction industries have gained major cost and efficiency benefits from the use of computers. However these industries are now at a cross-roads with two seemingly disparate developments - that of an increasing number of complex geoscience databases and, at the same time, the merging of all known data for the particular regions at minimal cost. These two developments can be managed by the development and of an industry accepted geoscience data model and dictionary. This will provide a common basis of understanding for geoscience data through a common language and a common structure for geoscience information. Integration of specialist systems and databases can then proceed efficiently. The development of a data model is going ahead with consensus from the mining industry. This is a joint government and industry funded project and managed through the Australian Mineral Industries Research Association, AMIRA. AMIRA is a well known research broker to the Australian mining industry obtaining sponsorship for projects both from private and government groups. The AMIRA project, P431, called the Geoscience Data Model, is to be the Australian standard data model for geoscience disciplines. The requirement for a standard geoscience data model has been recognised in Australia for some time. In October 1991, the Australian Government Geoscience Database Policy Advisory Committee (GGDPAC) established a Geoscience Data Standards Working Group which drafted a comprehensive list of data categories of the geoscience area. An AMIRA project called AMDEX was established to develop a transfer standard for the mining industry data at about the same time as this committee was in operation. The first AMDEX sponsors meeting was held in May 1991. It was proposed to use the US Spatial Data Transfer Standard (SDTS) as the basis to transfer mining data in AMDEX. A limited data model of mining data to be transferred was developed for the AMDEX standard under SDTS. The Australian Geological Survey Organisation (AGSO) saw the need to extend this and develop a complete data model for the geosciences and proposed this as a new project to AMIRA. This was strongly supported by GGDPAC which lead to sponsorship of the project from most state geological surveys. The Geoscience Data Model can be broken down into separate data models for a number of geoscience themes and sponsorship obtained so far will enable models to be developed for a comprehensive set of themes selected by the project sponsors. Further sponsorship is required to enable a more complete coverage of the geoscience area to be developed. Sponsorship for the Geoscience Data Model has been strong from the geological surveys and there was some effort by GGDPAC to promote the project in these organisations. An Australian geoscience data model is of immediate use to the geological surveys in assisting the standardising of huge quantities of geoscience data held by government agencies and it is preferable that this be an Australia-wide standard.

Jan 1, 1995