Search Documents

By James D

Fletcher Challenge Limited through its subsidiary Grampian Mining Co Ltd has carried out an ore evaluation of one of New Zealand's largest known deposits of ilmenite located at Barrytown on the west coast of the -South Island, New Zealand.The ilmenite is located in a beach sand environment which has previously been mined for gold. Two analytical techniques were developed to quantify the resource. Considerable difficulty was experienced in this phase of the evaluation due to the presence of major inclusions within the ilmenite grains. Wet and dry concentration circuits, utilizing spiral, wet magnet, high tension and plate electrostatic separators have been G47designed to produce ilmenite from the ore. Studies to utilize the titanium content of the Barrytown ilmenite have been made. Recent work has been directed towards a titanium dioxide pigment process.

Jan 1, 1986

A considerable debate has arisen regarding the best route for the beneficiation of iron ore. Supporters of jigging technology claim that although the technology is old, due to recent advances in jig control and a better understanding of the separation processes within jigs, it offers significant advantages over dense medium separation, especially in terms of reduced capital and operating costs and simplicity of design. Supporters of dense medium separation claim that this technology is proven to provide the best possible separation and that the gain in efficiency over the life of the plant, compared to that of a jig, will more than offset any differences in capital or operating costs. The truth is that both viewpoints are valid and that the choice is ultimately determined by specific characteristics of the ore being treated. Factors that need to be taken into account in deciding upon the correct option include the size/density distribution of the ore to be treated, the different size fractions which must be treated (lumpy or fines), differences in yield at grade, plant layout and capital and operating costs. Each of these factors will be discussed in detail and a case study for both lumpy and fines will be presented.

Jan 1, 2007

The products required by customers today have become far more complex and consequently more demanding to handle. And thereÆs the dilemma. Nowadays, people tend to stick to a trade for just a few years instead of for a lifetime, and this means that the customerÆs employees cannot be expected to get more than general knowledge of how to handle modern mining and construction equipment. To meet this challenge, major steps are being taken by suppliers to make their æmusclesÆ more user-friendly. Also the supplier is assuming a larger share of responsibility for the product including operators training, supply maintenance services and, in many cases, performance guarantees. In other words, the supplier is today supplying a function or an activity rather than just muscles. Some of the new generation drill rigs have been on the market for a few years and reliable experience has been collected and is addressed in this paper. Some of the information is well supported by figures while others are just statements from users of the rigs.

Jan 1, 2005

Development of the Greenvale orebody, containing 40,000,000 tonnes of nickel ore, began in 1971 and production commenced in 1974. Annual capacity is 2,800,000 wet tonnes. The variations in ore grade and physical characteristics which occur throughout the ore- body had a major influence on the selection of mining methods, grade control procedures, and equipment. After removal of overburden by scrapers, ore is excavated by draglines sidecasting into windrows. Feed to the crushing plant is .reclaimed by front end loaders into rear dump trucks according to a grade selection pro- gramme. After crushing, ore is stockpiled into blended units of ore of required quality. Ore is stacked and reclaimed for train loading using techniques designed to give maximum mixing of ore characteristics through Bach unit. These procedures are repeated on discharge at the plant site at Yabulu. The railway, constructed by Queensland Nickel Pty. Ltd. to Q.G.R. standard, and operated by the Q.G.R., is 216 km long and includes eight major bridges and three tunnels. Two trains per day, one of four locomotives and 92 waggons, and one of three locomotives and 69 waggons, haul crushed ore to Yabulu. Train loading is semi-automatic. A small township and associated services have been constructed for employees at Green- Vale.

Jan 1, 1974

By R P. Langford, T A. Moore

Over the last 15 years Indonesia has experienced a surge in coalexploration, which has led to the development of a major export industry. This coal exploration has improved the understanding of the geology of the Indonesian coal deposits. The main economic coal deposits are of Eocene and Miocene to Pliocene age, which mainly occur in Kalimantan and Sumatra and were formed from peat deposits in an equatorial paleoclimate similar to that prevailing today. Some of these peats were domed peats, which grew above the normal water tables, under a climate of year-round rainfall; these peats grew above the level at which waterborne mineral matter can enter the system, resulting in low ash and sulphur, and locally very thick coal. It is believed that such peats have formed the unusually thick, low ash, and low sulphur Miocene coals of Indonesia. Coal deposits of Eocene age are typically characterised by thinner seams, with relatively higher contents of ash and sulphur. The Miocene coals and Eocene coals both appear to have formed in lacustrine, coastal plain or deltaic depositional environments, similar to the modern peat-forming environments of eastern Sumatra and parts of Kalimantan. The Eocene coals formed mainly in extensional tectonic settings. Miocene - Pliocene coal deposits formed in a range of tectonic settings.

Jan 1, 1999

By D F. Akhmetov, M Yasuike, M Komazaki, Y Kawa

Remote monitoring of geological situation at distant regions with complicated relief, including reliable detection of the rock falls and estimation of the scale of accidents, is of great importance for practical needs. In the paper, vibration data, caused by fall of sample objects and registered by cable sensors, are processed and analysed in order to construct some measure for the indirect evaluation of weight of fallen objects. Nonlinear models, which based on artificial neural networks (ANN), are proposed for the signal presentation. To improve and simplify the learning and classification abilities of the whole system, the aggregative learning method (ALM) is implemented. ALM features relatively low memory and computational resources needed for the procedure realisation, especially for data classification (recall) stage, in compare to conventional methods. The validity and efficiency of the proposed approach are tested through its application for rock fall detection and weight evaluation system using cable sensors and mobile communication network. Classification abilities of the proposed approach are shown useful for estimation of the fallen object weight. Characterised with high computational efficiency and simple decisionmaking procedure, the derived method can be useful for simple and reliable real-time monitoring system design.

Jan 1, 2003

By S C. Dominy

A high nugget effect and the presence of coarse gold characterises many vein-gold deposits. The effective sampling of these deposits is often difficult because of the relatively low concentrations involved and erratic nature of the gold. Geological complexity often compounds this effect. Underground development, in-fill drilling and bulk sampling/trial mining are often required to delineate Ore Reserves. Winzing is an historical technique that was used to gather geological and sampling data during underground exploration. It permits access to the mineralised structure below the current datum to help determine viability. Winzing has always been considered an arduous and dangerous task. Modern technology has led to the development of the Mobile Supersucker, essentially a giant vacuum cleaner. This system permits safe and efficient winzing activities, and allows the collection of bulk samples for grade estimation. Bulk samples from horizontal development have long been collected to help define mineable grade. However, when defining blocks below current development, there has been over-reliance on ineffective æsmall sampleÆ drill data. The Mobile Supersucker permits safe and cost-effective development of winzes and off-winze sublevels.

Jan 1, 2003

By Pandey A. K, Srivastava A, Das A

Drilling and blasting constitute important activity in mining operations and account for around 20% of the total excavation cost. The utilization coefficient of energy for explosions of the fragmentation type is hardly 15 to 2035 and an enhancement in this is possible only through optimization of blast design. Designing a 'blast is a complex planning task, which for optimum results calls for matching the energy level of the explosive, rock properties and bench geometry. Optimum blast design needs a comprehensive study and an objective analysis of the intersecting elements. A cost optimised approach is often adopted with due consideration for all the cost sectors viz., drilling, blasting, loading, hauling dumping, and primary crushing, contributing to the overall miring cost. The present study deals with a performance prediction model which predicts the optimum burden for an explosive system in a given rock type to produce a certain desired fragment size. The model is framed on the inputs : shovel size, drill size, unit cost of drilling, bench dimensions, rock density, bond index, unit cost of explosive, maximum work potential. The model has been extended to compute the drilling and blasting costs for an assumed size of the bench to be blasted per round, so as to arrive at the overall cost optimization from a number of explosive systems. A comparative cost calculation with different explosive systems has been presented for a typical iron ore mine in India.

Jan 1, 1990

THE following description of the surface plant of the Great Fitzroy Mines is to be understood as having been compiled by a mechanical engineer, who concerns himself more with the various appliances used, their correct construction to enable them to accomplish their prescribed work, and the production and transmission of the power required to operate them, than with the reasons for the physical and chemical processes which those appliances are called upon to assist in carrying out. Hence the metallurgist will not find herein more than the skeleton of the organism, which perhaps he would wish to be clothed with the detailed description of the substances undergoing treatment, in their various combinations, at all stages, and the results attained in separating the valuable constituents from the worthless. So, also, no details will be found of the methods employed by the management for. the purpose of determining by sampling and assaying the nature of the various products obtained.GENERALThe ore being worked at the Great Fitzroy Mine is divided into two classes :-1. Ore that requires concentration before smelting.2. Ore that can be smelted direct.Flow-sheet (Fig. 1) shows in outline the process of treatment to which ore of the first class is subjected, and the writer will endeavour to fill in that outline with some details of the appliances used.

Jan 1, 1911

Project Hobson involves the replacement of an existing 90-year-old above-ground sewer that crosses Hobson Bay in Auckland, New Zealand, and which is nearing the end of its economic life, with a 3 km long, 3.7 m internal diameter segmentally-lined bored tunnel. The $118 M project will offer several benefits to the owner, Watercare Services Ltd, and the local community:provide capacity to meet projected growth in the region,virtually eliminate wastewater overflows into Hobson Bay and the Waitemata Harbour, andremove an obtrusive visual feature and open up the bay for recreational purposes. The geology in the region is a sedimentary formation, which has been significantly influenced by volcanic activity; 49 volcanoes are present within 20 km of the nearby city centre. The geology along the alignment is dominated by two palaeovalleys which have been infilled with a combination of marine alluvium and volcanic deposits. Watercare Services Limited has elected to manage and share tunnelling risk through, among other key measures, the implementation of a geotechnical baseline report (GBR); one of the first uses of this type of document in Australasia. This paper describes the general principles behind the use of a GBR, the development of the GBR used in Project Hobson and some lessons learnt.

Jan 1, 2008

The P49 Shaft, Hilton Mine, was sunk and equipped for Mount Ise Mines Limited by con- tractors Cementation - Thiess Joint Venture. The leached siltstones to a depth of 150m were known to contain large volumes of water. These siltstones were cored and tested in the laboratory. Field results confirmed that cement grouting was relatively ineffective but that chemical grouting was effective. The Sm diameter shaft was sunk to a depth of 1040m. Weak strata to the full depth re- quired continuous temporary support by rock bolts and mesh before the concrete lining was poured, and made sinking conditions difficult. After completion of the shaft sinking the headframe was redesigned and modified to allow shaft equipping as a combined service and hoisting shaft with seven compartments. The shaft steelwork was designed and fab- ricated for service with high speed conveyances operating under corrosive conditions. The steelwork, weighing approximately 1500 tonnes, was installed to a high degree of accuracy which required guides not to depart from true verticality by more than 2mm over any 5m, or 15mm over the full shaft depth.

Jan 1, 1976

Full aerodynamic design development of the proposed fans for the enlarged primary ventilation system at Mount Isa Mines Limited was initiated before tender specifications were prepared. Theoretical and analytical design studies were made of many possibilities to determine the optimum proposal. Major considerations were efficiency, simplicity, standardization, and mechanical feasibility. Model testing and experimental work covered blading design, inlet shape, diffuser and tail fairing dimensions, instrumentation requirements, ancl noise studies.Theoretical and predicted performance estimates were prepared for the three 20 ft diameter vertically mounted axial flow fans.

Jan 1, 1967

There are a number of different mechanisms by which wetlands can immobilise the metals in mine drainage. Here, the biogeochemistry behind four of these mechanisms (adsorption, biological uptake, precipitation as oxyhydroxides, and precipitation as sulfides) is discussed from the perspective of sustainability. Moreover, treatment wetlands are considered as part of a larger system, also taking into account the source of the drainage and various aspects of the receiving waters. The biogeochemistry of different metal immobilisation mechanisms in wetlands determines what kind of drainage can be treated with success, and it also places an upper limit on the amount of metal that can be removed from the water phase per unit of time. This has important implications for the design of treatment wetlands, perhaps particularly in colder climates. A thorough understanding of the prevailing biogeochemical processes is essential when attempting to establish treatment wetlands after the closing of a mine. If a wetland is to be used as a sustainable æwalk-awayÆ solution, the anticipated change in treatment efficiency over time (as pollutants accumulate in the system) must be considered in relation to the expected changes in drainage quality. It is also important that the total metal immobilisation capacity of the wetland is not exceeded and that the integrity of the system is maintained, in order to minimise liberation of previously immobilised metals.

Jan 1, 2003

By W Pytel

A special model of vertically loaded pillar behaviour is introduced to the general, multi-plate based, floor-pillar-roof system interaction analogue. This permitted analysing room-and-pillar mine systems in any geological conditions, including the effect of pillar elastic-plastic behaviour with strain softening. In the model, pillar instability is one of the important phenomenon, which may be expected to occur, and which the operator has to be prepared for. Thus the entire systemÆs safety is determined mainly by strong roof strata behaviour and therefore they have to be examined in actual stress-strain conditions utilising the appropriate strength theories. It was assumed that the so-called safety margin, representing the relation between load intensity and material strength, might serve as the basic indicator of possible roof instability development. Therefore, the safety margin may be estimated by comparing the actually computed components of stress-strain tensor with ultimate values characteristic for a given material determined in laboratory. In order to illustrate the effect of technological pillar size on roof strata stability, two different mining systems (methods of mining) in one of the æPolkowice-SieroszowiceÆ Mine districts was modelled using the finite element method formulated in three dimensions, assuming different materials within different rock mass strata, as well as a number of horizontal planes of discontinuity within the model.

Jan 1, 2003

The development of reliable and accurate solution sampling systems plus on-line atomic absorption spectrophotometers and voltammetric analysers at Pasminco Metals - EZ's (PMEZ) zinc refinery at Hobart, Tasmania, has led to extensive implementation of On-Stream Analysis (OSA) throughout the hydrometallurgical circuit. These systems complement industrial autotitrator and colorimetric analysers and with the comprehensive use of a powerful integrated Distributed Control System (DCS), provide extensive monitoring and control of all the important in solution' parameters for the plant. Samples can be left unaltered, or filtered or settled, to remove solids. They are then precision diluted and pneumatically transported to analyser shelters, where they are analysed for zinc, acid, copper, cadmium, lead, antimony, cobalt, nickel, mercury and ferrous, ferric and/or total iron. The range of analyses depends on the sample itself. The results are used for feed forward and/or feedback control of reagents where possible, or simple trend monitoring and out-of-specification alarming when closed loop control is not practical. The overall system reliability and accuracy is such that many daily composite plant samples are no longer analysed off-line. Operator sampling has also been reduced, and in two places, autotitrators with automatic sample pre-treatment have been installed for preparing and analysing samples collected by operators.

Jan 1, 1993

Early in 1930 William S. Robinson, Managing Director of Zinc Corporation Ltd., anticipated a rise in the price of gold and a devaluation of the Australian currency. 'WS', as Robinson was known, formed a.syndicate in London, which later became incor- porated as Gold Mines of Australia Limited (GMA) to invest in gold mining properties in Australia. GMA examined many prospects and subsequently undertook the development of several mines in eastern Australia. The syndicate also held a number of options and several large reservations for gold exploration in Western Australia over which it was proposed to carry out an aerial survey and thorough scien- tific assessment. To do this Western Mining Corporation Limited (WMC) was incorporated in Melbourne on the 2nd March 1933. The founding chairman of WMC and GMA was the highly respected `Collins House' figure, Sir Colin Fraser. The aerial survey was carried out, and a group of eminent geol- ogists from Harvard University examined many prospects and identified several which warranted development. To finance these activities `WS' formed Gold Exploration and Finance Co. of Aus- tralia Ltd. (GEFCA), in London in July 1934. GEFCA ultimately held 95% of WMC and 62% of GMA. The finance came mostly from London based South African mining companies which had been subscribers to his earlier syndicate plus some American inves- tors. (The Group Structure in 1936 is shown in Appendix `B").

Jan 1, 1988

This paper reviews the developments in understanding of the entrainment mechanism and its modelling in industrial flotation processes over the last 30 years. Both valuable and gangue minerals in the pulp zone of an industrial flotation machine can be transported through the froth zone to the concentrate launder in the water which must also be transferred from the pulp zone to maintain a stable froth zone in conventional flotation. A size dependent portion of each entrained mineral continues in normal circumstances to the concentrate launder. The size dependency arises because the larger particles are able to drain more successfully from the froth region. Gangue minerals are recovered by a number of mechanisms, entrainment being an important one in many cases. The entrainment mechanism is discussed on the basis of the pattern observed in recovery û size data for minerals. Its industrial implications are discussed and means of minimisation of the importance of the mechanism are also discussed. Various means proposed for mathematical modelling of the entrainment mechanism are also described. The effect of process variables on key parameters in these models is reviewed. Properties of both the pulp and froth zones are discussed where needed and means of taking additional measurements with devices developed over the last ten years are discussed as part of the collection of more detailed data on the flotation process in general and the entrainment mechanism in particular.

Jan 1, 2005

Western Australian tin deposits are similar to those of other Precam- brian terrains in that they are mainly associated with rare-metal pegmatites, in which cassiterite is found with minerals containing any or all of the elements Ta, Nb, Be, Li, Cs, Rb and the rare earths.. They differ from Phanerozoic deposits where cassiterite occurs in quartz veins, greisens, dis- seminations in granite or sulphide lodes, and is associated with minerals containing W, Mo, Bi, Sb, As, Ag, or Cu. The main tin production in Western Australia has come from the Pilbara Block where the more important tin- bearing pegmatites are related to a younger granite phase, and from Green- bushes where large albite pegmatites intrude ?Proterozoic metamorphic rocks. The more important tin deposits in the Pilbara Block, and those in the Halls Creek and Murchison Provinces, are related to granites which are richer in Si and K and poorer in Ca, Mg, Fe and Ti than 'average granite'. The tin granites tend to have higher than average contents of Sn, Rb and Li.

Jan 1, 1973

I start with some lines from "Pleasures of Hope" by the poet Campbell, published in 1798, which sets the flavour of what I am going to say. They blissful omens bid my spirit see The boundless fields of rapture yet to be; I watch the wheels of Nature's mazy plan, And learn the future by the past of man. I hope to echo the poet's optimistic view of what is yet to come. I am not sure I can find all the omens blissful but we all have some experience of what the wheels of Nature's mazy plan get up to. His advice to learn the future by the past of man seemed sensible to follow, so on the principle that the past of several men would be better than one alone I invited Alan Attwood, Maurice Cahalan, Gavin Moncrieff, Derek Temple, and Peter Wright to help me prepare this address; I am most grateful to them for their contributions. Of the technologies covered in this sequence of keynote addresses, metallurgy is the one which is closest to our consumers. On the age-old principle, which I do not expect to see changed in the 21st Century, that production is about providing the customer with what he wants, when he wants it, where he wants it, and at a price he can afford, I think we should start by trying to see how the market place is likely to develop, and to work back from there to review what technology we need to meet these demands.

Jan 1, 1986

The resource sector is conservative industry and people are resistant to change. The methods and procedures used to implement changes in process plants ultimately determine the success of such changes. The financial managers have a large say in where money is spent and the technical personnel must justify the cost and benefits for any expenditure. There are also others who believe it canÆt be done û æwe tried thatÆ. Implementing change needs a æChampionÆ who can assess the risks, plan, define the objectives and scope, set the goals, determine the key performance indicators (KPIs) and stay focused. This also requires preparing a budget and schedule and measuring against this. Contract management, reports and reviews are part of the implementation. Several case studies are given as examples of the implementation of process design changes to highlight the critical aspects involved.

Jan 1, 2009