Search Documents

A survey has been undertaken of the petrography of North Island greywackes with a particular focus on the occurrence in them of smectite (swelling clay) and chlorite, two minerals that are closely associated, chemically similar, and commonly interlayered with each other. Smectite is the mineral which is a major cause of greywacke aggregatesÆ poor performance. Smectite occurs in post-metamorphic shear zones and in surface weathering profiles over greywackes. This study focuses on the petrography of fresh greywacke rocks.   The occurrence and abundance of smectite and chlorite and their relationship in greywackes is largely a function of the chemistry of the sediment and the maximum temperature that the sediment has been subjected to during diagenesis and/or very low grade (anchizone) metamorphism. Rock chemistry, particularly total iron and MgO, determines the smectite and/or chlorite content in fine-grained greywackes (argillites and siltstones) but chemistry is less influential in sandstones, where at low grades of metamorphism much of the Fe and Mg of the rock is held in unreacted detrital minerals and the mineral constituents of lithic grains.   Four zones which represent different levels of diagenesis and very low grade metamorphism, based on the crystallinity of illite and chlorite in the greywackes, and the proportion of smectite interlayered with chlorite, have been mapped in the North Island. In the anchizone smectite does not appear as a discrete mineral, it is always interlayered with chlorite. In the upper anchizone chlorite contains approximately ten per cent of smectite interlayered with chlorite. In the lower anchizone about 30 per cent smectite can occur in chlorite.   In addition to the smectite and chlorite inherent in the greywackes as the result of the thermal overprint, smectite as a discrete mineral and smectite-chlorite interlayered minerals with high levels of smectite, occur in abundance on shear zone surfaces and in alteration zones adjacent to shear zones; these are the main contributers to the high levels of smectite recorded in many greywacke aggregates.

Jan 1, 2006

As requested by my fellow members I shall endeavour to read a paper on the Treatment of the Auriferous Sulphide Ores of Kalgoorlie from a metallurgical standpoint. Before going into the subject it will be necessary for me to make some slight explanations. As most of you are aware many of our London friends holding interests in some of these mines think it necessary that their doings should be shrouded in mystery. The result of this is that in some cases it is impossible to get any official figures from the mines for this paper. I must ask you not to lose sight of the fact that in treating the sulphide ores of the Kalgoorlie mines we had absolutely no data to start on, and that to-day. we are just beginning to get a fair grip of tbe subject; and though very high extractions were announced when the first plants were started on sulphide ore, it was well known that this was only to maintain the public confidence in the mines to allow time to make necessary adjustments; and, as showing the advance made in the treatment of the ore, I notice several of the mines have published the results of the final or re-treatment of the residues of their first sulphide treatment. I have also had the opportunity afforded me of thoroughly sampling the residues of several of the principal mines, and find the results as now published absolutely correct.

Jan 1, 1901

By Wesley, Worner H

During the meeting of the Institute last year at Port Pirie, the opportunity was taken to sample the lead bullion coming from the blast furnace and various stages during the refining process. Also, in the desilverising section, the upper zinc rich phase was sampled as the silver content built up and in the cupellation operation a series of samples was taken as the silver content of the bullion increased. In these two cases, the samples were taken under the supervision of a member of the staff of the Broken Hill AssociatedSmelters.In the following account of the microstructure of the samples taken, only the main phases present have received attention. In this connection deduction from phase diagrams of binary alloys has been used in conjunction with the assays carried out on duplicate samples taken at the same time as those for micro examination.

Jan 1, 1938

By B McCreath

Industrial process water for the Commodore Coal Mine and the adjoining Millmerran Power Station is provided by pumping secondary treated sewage effluent 100 km from the Wetalla Sewage Treatment Plant near Toowoomba. (A separate source is used for potable water.) The effluent is not of sufficient quality for discharge to a watercourse, but it is suitable, with further treatment, for the mine and power station. In designing and constructing the pipeline, special emphasis was placed on preventing accidental spills or planned releases to the environment. The pipeline and associated works can transfer 1000 ML/annum for reuse in the coal mine and power station.

Jan 1, 2003

Advanced Jig Separation of Shredded Plastics The authors have reported that the RETAC jig is very useful in separating relatively low density particles such as plastics, and demonstrated that highly efficient jig separation of plastic components in discarded office machines is possible in pilot-scale tests. To further improve the separation efficiency, a hybrid jig (RETAC jig with air bubbler under the particle bed) which can separate plastics having similar specific gravities using differences in wettability produced by a pretreatment, and a reverse jig (modified RETAC jig for plastics lighter than water) were developed. This paper reviews the separation of shredded plastics using advanced jig separation technology (RETAC, hybrid and reverse jigs). Wettability control of the plastics for the advanced jig separation is also reported.

Sep 13, 2010

By Pupazzoni P. D, Meissner D. C

Incorporating an iron ore pelletising plant, a MIDREX'"' Direct Reduction Plant, and a mini mill, the conversion of iron ore fines to high- quality steel slabs in Western Australia is among the lowest cost routes in the world. The cost and availability of iron ore and natural gas, government support, and proximity to the growing Southeast Asian market all contribute to the competitive position of the area. Owing to the lead-time required, this is an ideal time to develop a new project to supply semi-finished steel to Asia for rolling to a finished product. A project contracted now will start up in about three years, when the market should have recovered.

Jan 1, 1999

By E Heath, F McDermott, S Turner, P van Calsteren

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath midocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and om, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100 000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50 000 years prior to eruption.

Jan 1, 1995

The development of a noise attenuated compressed air driven fan is described. The fan, which employs the jet reaction principle, possesses blade extension pieces which penetrate into an acoustically treated annular chamber. The dominant noise source, namely the air jets, is thereby partially suppressed. In addition, the increased moment arm of the jets leads to an improved propulsion effect which contributes to the improved aerodynamic performance of the unit.A typical measure of the improvement of this type of auxiliary mine ventilation unit is a 4 per cent increase in efficiency and a 10 dB (A) drop in sound level for a fan duty of 0·5 kPa and 1600 litre/s. This degree ofattenuation corresponds to at least halving the loudness level, a subjective noise measure.

Jan 1, 1973

By D Craw, K A. Hunter

Deposits of the metalloids arsenic and antimony occur in quartz veins of mesothermal hydrothermalsystems in the South Island as arsenopyrite (AsFeS) and stibnite (Sb2S3). Arsenopyrite and stibnite occur in natural exposures in gold-mining areas, and additional arsenopyrite and stibnite have been exposed to the atmosphere by mining activity. At present the drinking water limits for dissolved As and Sb are 10 ppb and 3 ppb respectively. Sampling and analysis techniques are critical to determination of metalloid concentrations at these low levels. Endeavour Inlet in the Marlborough Sounds is an historic mining area (late 19th Century) with elevated As and Sb in waters emanating from mineralised rocks. Waters running out of abandoned adits have concentrations of As and/or Sb up to ppm levels. Natural waters have high Sb and low As, and the As levels increase markedly where anthropogenic activity has exposed rock. Changes in Sb/As ratio could potentially be used to quantify the anthropogenic component of metalloid mobility on mine sites on the 100-year time scale.

Jan 1, 2002

Rhyolitic rocks are volumetrically significant in the eastern part of the Coromandel gold province, yet deposits hosted by rhyolite (Kapowai, Broken Hills, Neavesville, Wharekirauponga and Waihi Beach) are generally low grade and subeconomic, especially compared with andesite-hosted deposits. In contrast, rhyolitic volcanic centres in Nevada host a number of economically significant epithermal gold deposits such as Round Mountain, Sleeper and Bullfrog. The Nevada deposits are associated with 27-20 Ma continental arc volcanics dominated by ignimbrites (eg Round Mountain), or younger 17-9 Ma bimodal rhyolite-basalt volcanism related to extensional basin-and-range tectonics (eg Sleeper). The Round Mountain deposit is localised on a caldera boundary fault and the mineralisation was deposited soon after eruption of the host rhyodacitic ignimbrite. In other Nevada deposits, hydrothermal systems are linked to the closing stages of flow-dome complexes and mineralisation is localised along normal faults associated with extensional basin-and-range tectonism. The style and composition of the mineralisation is similar in both the Coromandel and Nevada deposits and consists of sheeted and stockwork quartz veins, containing electrum as the main ore mineral and only minor sulphides (mainly pyrite) Likewise, the vein minerals were deposited from low salinity hydrothermal fluids in the temperature range of 200-270¦C. Both the Neavesville and Round Mountain deposits are geochemically anomalous in molybdenum. The deep oxidation of the Nevada gold deposits, dry climate and low level of competing land uses combine to make it economic to mine and process very low grade ore (0.2 - 2.0 g/t Au) by heap-leaching with cyanide solutions in most areas of Nevada. Although extensive low grade gold mineralisation is known at deposits such as Wharekirauponga and Neavesville, it is sub-economic because of shallow oxidation and land use conditions that are unfavourable for open pit mining and heap leaching.

Jan 1, 1996

Approximation of Surface Area of Fines in Blast Induced Fragmentation The surface area of fragmentation, especially in the finer size fractions, is a useful property to characterise the mechanisms of rock breakage. In the past, researchers have made assumptions with regard to the shape of fragments in order to estimate surface area, such as that all fragments are the same shape or all fragments are spheres. Often these assumptions were developed with inappropriate measures and returned considerable variability and error for the calculation of surface area. This paper reports a model to estimate fragmentation surface area from sieve sized raw data and a density measurement, with experimental validation down to a size fraction of -45 + 38 ?m in a range of rock types. After characterisation of particle shape, a range of fragment shapes was found to be in each size fraction. Nevertheless, in the ?2 sieve series the average fragment mass, volume and the size fraction standard deviations could be predicted reasonably accurately. Ellipsoid geometry was used to describe particle shape. Using these parameters and the number of fragments (also predicted) in each sieve size the individual surface area of each fragment was simulated.

Sep 13, 2010

Tried, Tested and Proven - 300 m3 Flotation Cells in Operation

Sep 13, 2010

As a minerals company, obtaining the appropriate consents under the Resource Management Act 1991 and getting permits granted for exploring, prospecting and mining under the Crown Minerals Act 1991, is necessary for actively exploring and mining in New Zealand. But the essential mix of ingredients for a viable and healthy Industry go way beyond this.   In the short term, an individual company seeking to operate on or within the Crown minerals estate of New Zealand must chart a course through the requirements raised by new cornerstone legislation, the Resource Management Act, the Crown Minerals Act and, the Conservation Act 1978 (where the minerals sought coincide with this estate).   However, this paper suggests that in the longer term for individual operators within the Industry and for the Industry at large to remain viable and sustainable and for New Zealanders to continue to enjoy its benefits, much more is required. Not least of which is a better balancing of competing uses and attitudes, which will require an opening of minds, a change in mindset, topped off with those two most essential of ingredients advocacy and leadership.   New Zealand has undergone massive restructuring in the last 15 years. Is it complete? Have each of its fronts evolved to the end point which was envisaged by the designers of the regime? What are the advantages? What is left to be done? What are the impediments from an incomplete transition which are left to either dog the Industry or remain as a challenge to be removed to ensure the Industry's smooth sailing into a prosperous and environmentally clean and friendly future? A future wherein an educated and understanding public welcome and are proud of the Minerals Industry to whom they owe the standard of living which they enjoy.   This presentation will examine the role of the New Zealand Minerals Industry Association (NZMIA) in paving the way for an optimum operating environment in which to couch a healthy industry into the future.

Jan 1, 1997

The last one decade in India had witnessed phenomenal growth in the coal, lignite, iron ore, limestone and many other minerals. To meet the production of minerals, the energy requirement is also very high both in terms of petroleum products and electrical energy. Because of spiralling prices of crude oil and also of the electrical energy, attempts have been made by various mining companies to select energy efficient mining machineries (in underground and surface) mines, together with energy efficient mining and mineral processing operations. Mineral sector of India is working seriously in tune with the Planning Commission stipulations to conserve energy.Apart from energy use (both electrical and fossil fuels) in mining, it is also significantly contributing to the cost of mineral processing depending on the quality of ore/rock being processed. Over the years a number of studies have been initiated and implemented to reduce cost of energy bill. An attempt has been made to present the various aspects of energy conservation, Impact of Energy Conservation Act 2001, Relevance of energy audit, areas of energy consumption and conservation efforts, etc in this paper. The paper also deals with some of the case studies to show how energy conservation programs has been implemented in the Indian mineral sector.

Dec 6, 2010

TowerMill - Advantages in Wet Grinding Applications The TowerMill, which has now been in existence for no less than 50 years, is one alternative to the horizontal ball mill and offers several advantages. The TowerMill is widely used in (coal-fired) electric power plants for the grinding of raw material for the FGD (Flue Gas Desulphurisation) process involving very high throughputs, very fine product sizes and high availability. Some companies in the mining industry also looked at the use of such optimised grinding machines several years ago and found that many of the advantages offered in other industries are transferable to new applications. Much development work has been undertaken to improve the TowerMill for new applications and, as part of that work, tests have also been conducted to make direct comparisons of their performance with that of ball mills. Grinding tests were performed using the same raw materials and comparable machine sizes. Some of the results are discussed in this paper, along with a comparison of the advantages and disadvantages. The conclusion provides an outlook for some worthwhile future applications. The test results, which are described and analysed, show that the TowerMill offers significant advantages in relation to operating costs and operational safety. An example based on the wet grinding of limestone is presented.

Sep 13, 2010

By P Taskinen, D Lindberg

The increase in metals demand in the electrifying globe means significant growth in the smelting of copper, nickel, zinc, and lead, produced from primary sulfide sources or using sulfide mattes as the intermediates of the process chains. This means that leaner and complex mineral deposits will be evaluated as ores and are in the future traded in the commodity market for smelting and refining to pure metals. An important issue in the trend is the technology metals, like antimony, tellurium, and gallium, which exist as trace elements in sulfide ores and form no ores of their own. Their recovery becomes important in the coming decades as will be the case with growing slag amounts without use in other industries. The key is to produce environmentally acceptable slags in the smelting operations. It sets new boundary conditions to the treatment of flue dusts. This means that all material streams of smelting and refining must be re-evaluated for the deportments of the main and minority metals. In copper smelting, the recoveries of precious metals are today important for the feasibility of the custom smelters but due to low prices of many minority metals they are discarded in slag landfills. It is one of the emerging issues also in the secondary copper smelting today and once the demand grows, the same question will be faced also in the mining-beneficiation-smelting-refining chain of the primary production of nickel, zinc, and lead. The distributions of many technology metals in the copper and nickel smelting have been recently studied using methods where the chemically bound trace elements in the slag and its phases at the smelting conditions have been studied. Thus, the key data about options for process modifications and additional processing steps are piling up. Short processing routes in the metals smelting and refining are attractive due to their simplicity. At the same time, complexity of many raw materials challenges the fluxing at high oxygen partial pressures in low silica slags with high metal concentrations. The compromise between high primary recovery and safe operation is a demanding task in conditions where slag foaming outside the processing window is evident. The increase in the demand of pure nickel is challenging the raw material basis where low-grade sulfide ores are soon smelted along with nickel laterites to matte. It is a demanding task at high MgO concentrations. The low solubility of MgO in iron silicate slags requires new fluxing strategies and new smelting end points for the operation at reasonable temperatures; the direct nickel matte smelting in one-matte mode may be an option.

Aug 21, 2024

By D Hill

In the Ngakuru area zeolite deposits occur in late Quaternary lacustrine vitric tuffs of the Ngakuru Formation and two of the deposits are being mined. The Ngakuru Formation overlies the Ohakuri Ignimbrite dated at c. 240 ka, and is overlain by younger alluvial sands and gravels. Individual zeolite deposits contain 50 - 80 per cent zeolite over a thickness of up to 45 m in thinly stratified vitric tuffs and are localised along NE-trending normal faults. Glass shards in the tuffs are replaced by the silica-rich zeolites mordenite and clinoptilolite. Amorphous silica (opal A), opal-CT, Kfeldspar and smectite are also present. The zeolites and other minerals are very fine grained (<10 8m), with open meshes of crystals that result in high porosities (52 - 70 per cent) in mordenite-rich tuffs. Zeolitic tuff samples typically have cation exchange capacities of 80 to 110 meq/100 g and internal surface areas of 25 - 58 m2/g, which combine to give high liquid and odour absorption capacities. The first zeolite deposit (Mangatete) was found in 1992, and this and the Twist Road deposit are worked by quarry benching into the side of hills. The zeolitic tuffs are dried and crushed to produce a variety of products including adsorbents for soaking up oil/chemical spills and animal wastes, animal feed supplements, water treatment, and sports turf and slow release fertiliser. The Ngakuru zeolite deposits formed at shallow depth (<100 m) along fault zones from reaction of glass-rich tuff beds with groundwater-diluted geothermal water during the late Quaternary, and are as young as 8500 yr BP from 14C dating of plant material in sinter associated with the Mangatete deposit.

Jan 1, 2005

By Wilson G. L, Lord J. H

A detailed analysis of faulting indicatcs that blocks of "greenstone" have been thrust beneath the southern end of the Mt. Isa orebodies.This "greenstone" basement is considered to be a major structural control in the localization of these orebodies.INTRODUCTIONThis paper is based on exploration carried out by Mining Corporation (Aust.) N.L. from 1956 to 1960 in the area immediately south of Mt. Isa, Queensland. During this period over 20,000 ft of diamond drilling was completed together with costeaning and geochemical exploration.Early in 1959, it became apparent that diamond drill information could not be correlated with the current geological concepts of this area and a detailed geological appraisal became necessary. In all, sixty square miles were mapped at a scale of 1 in. to 500 ft, using enlarged aerial photographs. All drill core was logged and sections re-interpreted.Professor K. C. Dunham of the University of Durham consulted on this project and contributed through valuable discussion. Dr. A. Day of the University of Sydney carried out a gravity survey in February 1960 and Dr. H. Wilshire of the same University undertook microscopic examination of rocks from the area. Certain sections of the area were investigated geochemically by Mr. K. K. Hughes of New Consolidated Gold Fields (Asia) Pty. Limited in 1960.In outlining a theory of ore genesis in the area the writers have drawn heavily on the invaluable data published by many previous workers on the Mt. Isa field, in particular...

Jan 1, 1963

Geostatistical methods have become well established in the last two decades for the evaluation of ore reserves in base metal, industrial minerals, coal and gold deposits of the Witwatersrand type. However, there has been considerable debate about the applicability of geostatistical techniques when applied to vein-type gold deposits with hydro or epithermal mineralisation. The main problems stem from a lack of spatial continuity and the highly erratic sample values that characterise these deposits. This paper reviews some of the current geostatistical techniques that are applied to the evaluation of gold prospects.

Jan 1, 1992

Commercially interesting deposits of zeolite rich tuffs and amorphous silica have been discovered recently in the Taupo Volcanic Zone (TVZ), North Island, New Zealand. This paper reviews them and comments on the potential for further discoveries. Potential markets for these unusual industrial minerals are discussed.

Jan 1, 1997