Search Documents

By R LEATHAM

Long hole drilling underground has come a long way since 'down the hole' surface drills were first taken underground. The underground miners have progressively developed the use of long hole stope drilling from the 'quarry blast' to a precise and selective removal of ore while leaving the remaining structure as undamaged as possible. To reach this position has involved the development of equipment and explosives to give the desired results. This paper reviews some aspects of long hole stope production drilling.

Jan 1, 1992

By Jensen W. S

The Mount Morgan ore-body is intersected by dykes to such an extent that it presents peculiarly difficult problems in extracting ore. These are shown on Plates Nos. LXVII. and LXVIII. Besides ,these dykes there are innumerable "heads," which alsoare a source of danger. Falls of ore occurred in the end of the year 1908, resulting in serious loss of life to miners employed. It was decided, after an exhaustive inquiry, to change the entire system of mining from the" flat backed stope system" to the" square set sectional system ," the latter being more flexible and allowing bad ground to be cut out from a safe position; but it became evident that, whatever system was adopted, there would be more or less danger unless all the dykesand heads known were picked up, and their continuation plotted on a special set of plans on which the general scheme of stoping could be plotted from time to time as work progressed. It is worth while pointing out that, in every other branch of engineering, it is usual to design the work, and that only in mining engineering has it been common to do the work first and plot it down afterwards.The term "sectional analysis" is familiar in most branches of engineering design, and as applied in this paper to mining, may not bear the same meaning, but the general purpose is analagous, and there is no other term used.

Jan 1, 1911

By MattelmSki M

Outokumpu Harjavalta Metals Oy has been producing nickel since 1962, based on conventional flash smelting technology followed by electrowinning of nickel. In the 1980s, a research project was initiated to develop a converterless direct smelting process to produce matte for further refining in the then existing refinery. The process was tested on a pilot plant scale at Outokumpu's research centre in Pori and was found to be viable. The process was named the Direct Outokumpu Nickel Smelting Process or the DON Process. At the turn of the 1990s, Outokumpu studied various options to develop its nickel business and the Harjavalta operations. As a result of this work, the DON Process was further developed to produce two mattes: low iron matte in the flash furnace to be leached in the existing leaching circuit and high iron matte in the electric furnace to be leached in the new leaching circuit. In Harjavalta's case, it was essential and important that the process could use the existing flash furnace and electric furnace without converters.

Jan 1, 1996

By F Minz, P Lamberg, A Mwanga, C Lund, C Wanhainen, M Amiri Parian, J Rosenkranz

A geometallurgical model is currently built in two different ways. The first and the most common way relies on geometallurgical testing, where a large number of samples are analysed for metallurgical response using small-scale laboratory tests, eg Davis tube testing. The second, mineralogical approach focuses on collecting mineralogical information over the orebody and building the metallurgical model based on mineralogy. At Lules University of Technology, Sweden, the latter method has been adopted and taken further in four ongoing PhD studies. The geological model gives modal composition by the help of element-to-mineral conversion and Rietveld X-ray diffraction. Texturally, the orebody is divided into different archetypes, and liberation measurements for each of them are carried out in processing fineness using IncaMineral, a SEM-based technique. The grindability and liberation spectrum of any given geological unit (sample, ore block, domain) are extrapolated from the archetypes. The process model is taken into a liberation level by mass balancing selected metallurgical tests using the particle tracking technique. The approach is general and can be applied to any type of ores. Examples of ongoing studies on iron and massive sulfide ores are given.CITATION:Lamberg, P, Rosenkranz, J, Wanhainen, C, Lund, C, Minz, F, Mwanga, A and Amiri Parian, M, 2013. Building a geometallurgical model in iron ores using a mineralogical approach with liberation data, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 317-324 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By A J. MacDonald, M P. Raffield

The South Deep massive orebody consists of 20 to 30 m of payable conglomerates ranging in dip from 11¦ to 20¦ and at depths of between 2400 m and 3400 m. The mine design process selected a mining method with a proven record of application that could be adapted to overcome the inherent difficulties associated with the depth, thickness and structural influences of the South Deep orebody. A modified cut and fill mining method provides a concentrated and highly flexible method of extraction. An integrated destressing cut will enable the modification of the stress environment such that it is suitable for massive mining operations. The choice of backfill type and stoping width in the destressing cut ultimately determines the characteristics of the stress modification and, as such, is critical to the success of the cut and fill operation. This paper discusses the decision process undertaken to determine the optimum backfill type and stoping width combination in terms of, conditions in the destressing cut faces and in the massive mining environment. Numerical modelling has been extensively used to analyse various scenarios to aid in the decision process.

Jan 1, 1998

By Donchak P. J, Champion D. C, Fordham B. G, Domagala J

The Hodgkinson Province forms the northern part of the Tasman Orogen and contains the most extensive outcrops of Silurian - Devonian rocks in Queensland. Deep-water, marine siliciclastic sequences (mainly turbidites) dominate most of the province except near the western margin where mafic volcanics and fossiliferous limestones characterise much of the succession. It is difficult to apply normal stratigraphic mapping techniques to the Hodgkinson Province because of extensive stratal disruption by numerous thrust faults, the general lack of stratigraphic and structural markers, and the unfossiliferous nature of much of the succession. Nevertheless, several distinct units have been delineated although their internal stratigraphy or boundary or superpositional relationships are uncertain. Ordovician strata, as well as two major unconformities have been recognised in the western part of the province. Several models have been proposed to explain the evolution of the Hodgkinson Province. Although there is no general agreement most recent researchers favour an extensional tectonic regime.

Jan 1, 1990

Western Deep Levels, a seismically active deep level gold mine, started placing backfill in their narrow tabular workings as part of the regional support strategy in 1986. Over the years the percentage of working places being backfilled has been gradually increasing. At the end of 1995 the support efficiency and the labour productiveness relating to support installation were scrutinised to determine if resources were being optimised. Owing to financial, safety and productivity constraints it was decided to redesign stope support to be less labour intensive, safer and provide an integrated stope support system. This new integrated system will thus combine the previously used temporary, permanent and back area support consisting of mechanical props, hydraulic props and backfill respectively. Backfill previously formed an integral part of the regional support in conjunction with strike stabilising pillars. To design the integrated support system the backfill placement quality has to be exceptionally good and placement must be done as close as possible to the working face. The backfill to face distance was reduced by 30 per cent and in some areas by more than 50 per cent with an increase of square metres filled to increase the effect of the backfill even more. This paper addresses the design and successful implementation of an integrated stope support system based on the optimisation of backfill to the extent where installation of mechanical and hydraulic jacks could be eliminated.

Jan 1, 1998

Study on the Recovery of Zinc Minerals from the Tailing of a Lead and Zinc Mineral Processing Plant

Sep 13, 2010

By Robertson GE, McLaughlin JD

An extensive laboratory campaign was conducted to find a suitable water soluble collector to replace diphenylguanidine (DPG) in the matte separation process. The examination of the collectors was done by measuring the rate of flotation and the best candidate collectors were selected on the basis of the rate parameters. As a result of this search mercaptobenzothiazole (MBT) was selected for a plant trial. A plant trial of two weeks duration confirmed that MBT will produce separations at least as good as those obtained with DPG.

Jan 1, 1993

This paper suggests the models for determination the optimum life of machines on the basis of sum and difference of investment and maintenance costs. The economic-mathematical models are based on complex percentage method taking into account the time factor of referring cost. The following strategies of maintenance policy have been considered in machines repair: a strategy without investment, a strategy with continuous investment and a strategy with step-like investment. The effect of value of investment in repairing and time interval of investment on optimum machine exploitation life has also been considered. An illustrative example is presented.

Jan 1, 2003

The paper describes a simulating method.for ground water contamination originating from industrial and mining activrty. The finite difference model simulates heat, mass and solute transport. The applied stochastical method for dispersion provides more accurate solution of mass transport modelling. This method gives a more realistic approach of chemical processes in an aquifer depending on temperature.

Jan 1, 1988

With the exeption of the United States, Canada and Russia, oil has not been around in quantity near world centres of population. Production: in Western Europe is insignificant. Japan is without production as are Australia, Southern Africa, India; Brazil, Chile, New Zealand and China. The United States is, however, a large importer of crude oil. The very fact that oil is produced generally away from centres of population means that it has to be carried by sea to the area in which it is required. There is, therefore, a constant flow of oil around the world in very definite channels.

Jan 1, 1962

By Ritchie I, Fleay J

The key issues in the conceptualisation and testing of treatment options for gold and base metals mineral processing projects are discussed. A prerequisite of this process is the need for close interaction between geologists, mining engineers and metallurgists to facilitate an understanding of the orebody based on the parameters impacting on each discipline. Typical testwork programs for unit operations, including comminution, flotation and gold processing are Described.

Jan 1, 1997

The Granites Gold Mine has far exceeded the design capacity of 300,000 tonne per annum during its first sixteen months of operation. The presence of considerable free coarse gold has made it imperative that the gravity section operate at maximum efficiency. The inadequacy of acid digest- ing facilities and trying climatic conditions prompted management to initi- ate investigations into the use of Intensive Cyanidation as an alternative method for upgrading gravity concentrates prior to smelting.

Jan 1, 1988

THE Taranaki oil-field is situated on the western side of the North Island of New Zealand, at about its widest part, and may be said to be the most compact and fertile part of the Dominion, for, with the exception of the. upper half of Mount Egmont and of the ranges adjoining, which absorb 36,000 acres, the whole of the area, miuus what is taken up by the rivers land streams-is suitable for settlement, and certainly two-thirds is good land. The gross area oE the district is 2,417,299 acres.The principle rivers are the Wanganui, Mokau, Waitara, Patea, and Waiwakaiho. Mount Egmont, which is 8260 ft. high, used to be called Taranaki, and from it the district takes its name (the Maori meaning of which is "sloping peak ").

Jan 1, 1911

Portland cement is a finely ground mineral powder obtained by intergrinding a mixture of 95 parts of clinker and five parts of gypsum. It is the generic name for hydraulic cement a man made product which hardens in the presence of water. Today's cement started formally with a patent granted in 1824 to Joseph Aspdin, a Leeds bricklayer. He called his patented cement 'Portland' because it resembled a gray brown stone quarried on the Isle of Portland off the coast of England. The first cement to be made in the southern hemisphere is accredited to Nathaniel Wilson, a pioneer farmer who with his brother John began experimenting in 1874 with the limestone on their property near Warkworth. In 1884 they produced the first Portland Cement to be made in this part of the world.

Jan 1, 1978

By Chisholm J. M

Why go to the CIS? The vast mineral potential of the Commonwealth of Independent States (CIS) has long been recognised, but it has taken the lowering of the iron curtain to open up the region to serious mineral development consideration by the Western World. The advent of a free market economy and the emergence of the Independent States with pressing needs for foreign investment has led to a greatly improved investment climate. Coupled with the desire for some of the more entrepreneurial resources companies to head the wave of investment to the region, this sequence of events has promised a great deal, but delivered only modest progress to-date. Potential gold project development has provided the major focus, for three reasons: the region is highly prospective for gold, gold projects tend to have a relatively lower start-up capital cost compared to base metal and fossil fuel projects and finally bullion or refined gold is more readily transportable and easier to sell.

Jan 1, 1996

An assessment has been made of six reported methods for the determination of the swelling of iron ore pellets on reduction. The methods are discussed on the basis of apparatus requirements, reduction conditions, sample requirements, measurement of swelling and reproducibility. It is concluded that the CNRM, LKAB, and Lurgi methods are the most satisfactory which presently exist for determination of the swelling of industrially produced, iron ore pellets.

Jan 1, 1974

Pbo activities have been measured in conventional blast furnace and direct smelting type slags at 1200¦C. Much higher activity coefficients than previously measured have been obtained and attributed to interactions between iron and lead oxides. The behaviour of PbO in the two types of slag reflects their relative silica contents. Simple equations derived from mathematical modelling work are presented for the prediction of Pbo activities in complex industrial slags.

Jan 1, 1984

Automatic sampling and weighing of copper sulphide concentrate produced on Bougainville Island (PNG) is described. Contained metal weights gave satisfactory agreement with buyer's results after the introduction of polyethylene lined sealed aluminium foil bags for transport and storage of assay samples. Paper bags used previously for this purpose permitted oxidation of the sulphide concentrate and thus caused lower assay values.

Jan 1, 1976