Search Documents

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

By P J. Colbert, P D. Munro

OZ Minerals' Prominent Hill copper-gold concentrator in South Australia was built in 2008 with commercial production commencing in early 2009. In addition to recovery of valuable minerals, the flow sheet for this iron oxide-hosted copper-gold deposit has to address the issue of producing a good quality saleable copper concentrate by high selectivity against non-sulfide gangue. Detailed mineralogical studies integrated with the metallurgical test work highlighted that liberation of fluorine-bearing minerals and subsequent very efficient rejection in cleaner flotation was necessary to produce a commercial quality copper-gold concentrate. Bench scale laboratory metallurgical tests and mineralogical studies identified the need to regrind rougher concentrate to a P80 of 20 -25 microns or finer for adequate liberation of the fluorine-bearing minerals. Satisfactory separation of the fluorine-rich gangue material from the valuable copper sulfides requires highly efficient cleaner flotation. This is done by a combination of washed froth cleaning and conventional dilution cleaning. Proven equipment developed to meet similar taxing liberation and separation duties for the treatment of the refractory zinc-lead-silver ores of the Carpentaria-Mount Isa Mineral Province have been selected. The combination of Xstrata Technology's IsaMillÖ and Jameson Cell technologies addressed both the liberation and separation issues in the Prominent Hill concentrator. The energy efficient IsaMillÖ technology both regrinds the rougher concentrate while its inert grinding environment prevents contamination of mineral surfaces with 'debris' ensuring subsequent optimum flotation performance. Heading up the cleaner circuit with a 'scalping' Jameson Cell followed by conventional flotation equipment allows this section to take advantage of the Jameson Cell's high intensity flotation environment and froth washing capability to achieve maximum concentrate grade (at minimum fluorine levels) while maximising recovery through the use of conventional flotation machines. This paper looks at the development of the Prominent Hill flow sheet from the initial mineralogical and laboratory test work to the design, scale-up and early operation of the Prominent Hill regrind and cleaner flotation circuits. The mineralogically-based approach of domaining metallurgical ore types combined with the axiom of size-by-size mineral particle behaviour by liberation class gave a clear understanding of the liberation and separation issues involved in the processing of Prominent Hill ore. Technologies developed to meet much more onerous liberation and separation duties for the treatment of the refractory zinc-lead-silver ores of the Carpentaria-Mount Isa Mineral Province were successfully used to improve concentrate quality by rejecting non-sulfide gangue containing impurities. An IsaMillÖ and a Jameson Cell are included in the circuit for fine grinding and for additional concentrate cleaning. Plant performance since commissioning has justified the approach for metallurgical test work and equipment choices for the flotation circuit.

Jan 1, 2009

By A Tomsett, R Kidd, Z Casley

Bivariate recoverable resource estimation aims at predicting the recovered metal for a secondary variable when a cut-off is applied to a primary variable. The choice of a consistent geostatistical model is advisable to allow a robust estimation from exploration data of the primary and secondary metal recovery functions on a generic selection block (selective mining unit û SMU) within large panels. Ore processing decisions at Lihir Gold LimitedÆs Lihir Gold Mine are based on the gold and sulfur estimates of SMUs from production (grade control) data. The predictive model from exploration data at Lihir is based on the estimation of a recoverable resource for gold by Uniform Conditioning (UC), with an estimate of the sulfur grade being provided by Ordinary Kriging of panels. While univariate UC is adapted to the diffusive nature of the gold mineralisation (Ladolam orebody) at Lihir, the independent estimation of sulfur, through ordinary kriging, fails to capture the potential spatial correlation that exists between gold and sulfur mineralisation. This paper presents a practical implementation of bivariate UC, which better represents in the resource model the spatial correlation between gold and sulfur. Incremental economic gains through improved definition of material categories and scheduling are investigated, and the particular impact on the process of geological interpretation and domaining is emphasised.

Jan 1, 2009

By B Hall

In feasibility studies the choice of optimum cut-off grade is typically based on an evaluation of tonnage grade curves and manual design of stopes at one or two cut-off grades. In the industry these stope designs are usually based on break-even cut-off grades, but there is little consensus on what cost and price assumptions ought to be included. A new tool for automated stope design has been developed that generates sets of stope shapes for a nominated range of cut-off grades, or depending on the nature of the mineralisation, cut-off values based on net smelter return calculations in the block model. The stope design procedure includes constraints in stope and pillar geometry for the selected mining method and can be used to evaluate sublevel interval and sensitivities to other design parameters in the specific geological and geotechnical environment. These ænested stopesÆ are analogous to ænested pitsÆ in open cut design, and can be used as a key input in the æhill of valueÆ methodology for the evaluation of the optimum cut-off grade in underground design. The results of many consulting studies indicate that a break-even cut-off grade will not be the optimum cut-off grade. A particular benefit of the new stope design tool is that the design rules used to establish stope shapes in the feasibility study can then be used in mine production, in an optimal and repeatable method. This methodology is being advanced in the AMIRA P884 PRIMO project, which is a new research collaboration coordinated by AMIRA International. The project has brought together active research groups in Australia and Canada, with the goal of developing a flexible framework and set of software tools for optimisation in underground mine design.

Jan 1, 2009

By D Guibal, J Vann, M Harley

Many sample value distributions are highly skewed and present variograms with high relative nugget effects and/or short-range structures. In consequence, significant deskewing of the histogram and variance reduction occurs when transforming between sample and block support, where blocks are of significantly larger volume than samples. When making estimates in the mining industry we usually wish to estimate on the basis of block support rather than sample support. The selective mining unit (SMU) refers to the minimum support upon which ore/waste allocation decisions can realistically and practically be made. The SMU is usually significantly smaller than the sampling grid dimensions, in particular at exploration/feasibility stages. In a non-linear estimate, for each large block (by convention called a æpanelÆ) we estimate the proportion of SMU-sized parcels above a cut-off grade threshold. A series of proportions above cut-off defines the SMU distribution. Use of such non-linear estimates reduces distortion of grade-tonnage curves and provides a better basis for mine planning and economic decision-making. At present, Multiple Indicator Kriging (MIK) is the most widely used technique for performing estimation of recoverable resources. MIK is not the only approach available and it has some potentially serious limitations. The MIK technique is described and a number of theoretical and practical implementation issues are examined. In particular: MIKÆs assumptions about spatial distribution of grade; the behaviour of indicator variograms; application of change of support models; order relationship problems; and modelling the tail of the distribution. Some simple tests are described which allow us to determine the suitability of different estimators for a given deposit and criteria to identify a preferred estimator are also examined. Uniform Conditioning (UC), an alternative estimator which may be used instead of MIK, is described.

Jan 1, 2000

By J R. Robinson

Prior to mine development, exploration drilling within the Luise Caldera on Niolam Island encountered gold mineralisation to the northwest of the main Minifie and Lienetz orebodies. This mineralisation was referred to as the Kapit orebody, and ten diamond drill holes were subsequently completed over the area to investigate its economic potential. Several significant mineralised intercepts were returned. These were interpreted using the orebody model developed for Lihir at that time which invoked a strong horizontal control to mineralisation. Additional consideration was given to the elevated geothermal temperatures encountered, the proximity of the mineralisation to the ocean, and its perceived depth below sea level, resulting in the Kapit area being given a low priority for follow up investigation. As a result, no further work was completed over Kapit until recently. The Kapit orebody was the target of an intense diamond drilling programme during 2002/2003. Data from this latest round of drilling has significantly improved understanding of the mineralisation and associated geology. The significant orebody now delineated at Kapit substantially differs from past interpretations, and the latest data has upgraded its economic potential. A resource estimate and other critical studies completed in 2003 enabled an updated reserve statement to be issued in February 2004 including the Kapit mineralisation for the first time. Total Probable Reserves at Kapit stand at 25.2 million tonnes (Mt) at 5.28 grams of gold per tonne (g Au/t), for a total of 4.3 million ounces (Moz) of contained gold.

Jan 1, 2004

By G King, Q Shu, W Cao, F Gyakwaa, H Singh, S Wang, M Huttula, T Fabritius

Metallurgical slag, such as refining slag, is essential to enhance or promote steel cleanliness. The CaO–MgO–Al2O3–SiO2 system is the primary source of oxides-based inclusions. It plays a vital role in applications in various pyrometallurgical processes. Numerous thermodynamic databases and physicochemical properties of slag studies mainly focus on quenched samples and measurements at room temperature. Consequently, the present study explored the physicochemical, structural properties and crystallisation evolution for CaO–MgO–Al2O3–SiO2 glassy slags via in situ hightemperature Raman spectroscopy and synchrotron X-ray diffraction. The study was carried out by synthesising CaO–MgO–Al2O3–SiO2 slag with varying Al2O3/SiO2 ratios. The results from the in situ high-temperature measurement demonstrated a pattern showing a transformation of a broad peak from the glassy matrix to crystalline peaks. The study showed crystallisation of dominant phases such as Ca2SiO4, Ca2Al2SiO7 and CaAl2O4 that correspond and are attributable to changes of structural units during in situ high-temperature measurements. The results further showed a correlation between an increase and transformation in crystalline phases observed from the spectra obtained from non-isothermal heating of the samples.

Jun 19, 2024

By K Knorr

Desktop X-ray powder diffraction using a D2 PHASER equipped with fast linear detector was performed on several iron ore and mill scale samples. Data were analysed using cluster analysis and Rietveld quantitative phase analysis. The quantitative mineralogy of both materials could be established. Thus the input is provided for understanding the energy consumption and the CO2 emission during iron production. Furthermore, tabletop XRD allows to distinguish iron ore from mill scales and to quantify their mixtures.

Jul 11, 2011

By P Hanna

Following the Busang fiasco, more detailed guidelines were appended to the latest revision of the JORC Code released in September 1999 (JORC, 1999). Although the definitions and terminology essentially remained unchanged, the additional information in the guidelines has highlighted a number of issues for consideration by geologists undertaking computer-based resource estimations. The three main issues are:Data Integrity û details such as drilling and logging techniques, sampling procedures, assay tests, site visits, data recording and aggregation methods need to be considered. Geological Interpretation û is the Competent Person applying the appropriate software interpretation to the deposit in accordance with the regional setting. Are the correct computer-based tools being applied and are they producing the desired result (without compromise) to the satisfaction of the Competent Person? Modelling Technique û the importance of the relevant experience of the Competent Person not only in regard to the geology, but also with respect to the modelling algorithms and resource calculation methods of the computer software system involved. At the end of the day, it is essential that the Competent Person undertake a reality check on the resource estimation itself. They should also check that the borehole spacing is in accordance with the level of continuity for each critical parameter (such as structure, grade, impurities, etc) for which the resources are categorised.

Jan 1, 2000

Claiming the Green Revolution - Protecting Investment in Green Mineral Processing

Sep 13, 2010

A new bench blast design method and its realization with the assistance of the computer is introduced. The basic design principle is to define a rhomb cell, called fully- fractured zone, through a series of full scale bench crater tests and apply this geometric pattern in multi-hole, multi- row blast design. To illustrate the design method, the optimization process and assessment of blast performance are presented in the context of a case study.

Jan 1, 1992

Over a four year period from 1984 to 1987, a broad range of ground conditions were experienced in recovering old workings at the Walhalla mine in central-eastern Victoria. Access to the ore zone was gained via old workings and new development. The work included: Recovery of vertical and inclined shafts. Recovery of collapsed winzes. Recovery of level drives and crosscuts. Spiling through broken ground and old mullock. Pre-grouting of caved zones. New development using small-scale rail equipment and "bobcat" Loaders.

Jan 1, 1988

A mineral exploration manager's prime function is to provide a frame- work within which new mine production can be achieved. As part of this framework, the manager should know his employerb future requirements, and should direct exploration towards those particular mineral commodities which indicate satisfactory growth in consumption and price. Selection of these commodities can be assisted by studies of world reserves, and long term trends in price and consumption. Exploration planning is most efficient with an assured and reasonably uniform supply of funds.

Jan 1, 1980

By Green S, McKernan, Skrypniuk

In November 1996, Boddington Gold Mine (BGM) began the implementation of an expert system. The objective of the expert system was to improve plant efficiency by developing an `operator best practice' control philosophy for the grinding circuit

Jan 1, 1997

By Rautio V

The mining sector has been automated and robotised very rapidly during the last few decades. The organisation of work, schedules and housing has been modernised from the traditional modes of industrial society toward the more flexible modes of

Jan 1, 1998

By Wills BA, Barley RW

A brief description of viscosity measuring devices used in Dense Media Separation (DMS) plants is given, including a new On-line viscometer system. The various factors which affect suspension viscosity are identified. The effect of temperature variation on viscosity and viscosity measurement is examined in detail. Practical problems in using a modified Stormer viscometer for laboratory testwork are noted. Likely problems of continuous viscosity measurements are also discussed.

Jan 1, 1987

Coal has been mined in New South Wales for nearly 200 years and prior to 1970 the vast majority of this coal was mined from underground mines using bord and pillar or similar systems.Since 1970 there have been two notable changes in coal production trends in New South Wales as can be seen from Figure 1.1. The steady growth in coal mined by open cut methods. Open cut output grew from about seven per cent of the State's output in 1970/71 to 43 per cent in 1990/91.2. The steady growth in coal mined by the longwall method. longwall output grew from negligible amounts in 1970/71 to 48 per cent of underground production in 1990/91. mines operating longwall units produced 61 per cent of underground production in 1990/91.

Jan 1, 1992

By Peng SS

This paper presents a number of mathematical models for predicting the different phases of the complete surface subsidence process associated with underground longwall mining. A computer program developed based on the mathematical models is briefly introduced.

Jan 1, 1992

By J Safarian, M K. Kar

Bauxite residue is one of the most important by-products from the alumina industry with no commercial use till now. The utilisation of bauxite residue through pelletising with different lime additions, hydrogen reduction, and smelting has been studied in this work. Three different types of green pellets were made with varying calcite-to-bauxite residue ratio and subsequently sintered at elevated temperatures. The sintered pellets were isothermally reduced at 1000°C under hydrogen gas followed by smelting of the reduced pellets in argon at 1500°C. Smelting of the reduced pellets leads to the recovery of metallic iron and the formation of a leachable calcium aluminate slag. X-ray diffraction (XRD) and scanning electron microscope (SEM) were used to characterise the phases and microstructural analysis. The iron produced in the smelting process has a high purity, above 99.5 wt per cent. While the iron content of the slags is quite low, and the slags shows variations of krotite (CaAl2O4), gehlenite (Ca2Al2SiO7), and perovskite (CaTiO3) phases based on the variation of calcite addition. It was found that the more calcite addition in pelletising yields higher percentage of krotite phase as compared to lower calcite-containing pellets. Employing quantitative XRD analysis, the krotite phase fraction was found approximately 85 wt per cent for higher calcite-added pellet, and around 74 wt per cent for lower calcite-added pellet. FactSage™, ver 8.1 (Thermfact and GGTTechnologies) thermodynamic software was used to evaluate the obtained experimental data, they both revealed that the

Jun 19, 2024

A methodology is described to integrate heap leaching into a CIP operation. The paper firstly describes what is meant by a 'systems approach'. A broad view of the objectives of integration of heap leaching into CIP is given, followed by the components of the system, and then a description of the methodology for integration. The seven stages of integration are given as determination of distribution of gold, sampling, metallurgical testwork, conceptual study, pilot heap operation, pit modelling and pit optimisation. The final result is a series of optimised curves which determine the maximum value of the orebody, and the optimum cut-over grade from CIP to heap leaching.

Jan 1, 1992