Search Documents

By B S. S Rao, S Chandra

IndiaÆs iron ore mining industry is growing rapidly in order to augment the capacity to meet the unprecedented demand for the iron ore. Traditionally, much of Indian iron ore production came from exploitation of high-grade haematite ores, with the exception of Kudremukh which beneficiates lean grade Banded Magnetite Quartz ore. Now with the changed scenario of demand and supply, keeping long term sustainability in mind, it is imperative to develop suitable processing technology for exploitation of banded haematite quartz (BHQ) ore available abundantly and not utilised so far. In this direction detailed characterisation and beneficiation studies were conducted with BHQ iron ore from the Bellary-Hospet region of India, assaying 36.5 per cent Fe. The mineralogical studies with the image analyser system revealed the presence of maghemite and haematite as iron-bearing minerals. The gangue mineral associations were siliceous, ferro-magnesian and carbonate minerals. Higher degrees of liberation were observed in the size range of 75 - 212 microns. Liberation grind tests were performed by grinding the ore to different top sizes in a closed circuit laboratory ball mill with the ground samples subjected to Davis tube tests. The yield, grade and recovery were used as parameters to plan a two-stage wet drum magnetic separation based on grinding the primary magnetic concentrate. After subjecting the final magnetic concentrate to flotation to remove residual silica a concentrate assaying more than 68 per cent was obtained. The non-magnetic product from the primary magnetic separation was deslimed, ground, blended with secondary magnetic tails and was subjected to a two pass wet high intensity magnetic separation (WHIMS). The WHIMS concentrate was further subjected to two-stage flotation to remove residual silica to obtain concentrates assaying 64 - 66 per cent Fe. The final combined concentrate from wet drum magnet and WHIMS after flotation could yield a blast furnace (BF) grade pellet feed concentrate assaying more than 65 per cent Fe with a yield about 39 per cent and iron recovery about 70 per cent. A direct reduction (DR) grade pellet feed concentrate assaying 67 per cent Fe with a yield of about 28 - 31 per cent and iron recovery about 53 - 57 per cent could also be produced. Based on the test work, a process flow sheet was developed to beneficiate the BHQ ore for production of BF/DR grade pellet feed concentrate. In this paper methodology adopted for selection of individual process, various diagnostic tests performed to rule out other beneficiation processes and the final process flow sheet development is presented and discussed in detail.

Jan 1, 2007

By Jaques A. L, Heinrich C. A

Mt Todd lies towards the south end of the Pine Creek Geosyncline, sandwiched between the Cullen Batholith and the Edith Falls Basin, in an area of regionally metamorphosed sandstones, siltstones and shales. The Batman deposit, some 3 km west of Mt Todd is a sheeted quartz vein system hosted within greywackes of the Palaeoproterozoic Burrell Creek Formation (Finniss River Group). The gold-bearing quartz veins, trending 010¦-020¦ and dipping 60¦-70¦E, are commonly 0.5 to 5 cm wide and occur at intervals which are from 10 cm to 1 m apart. Gold tends to be restricted to the quartz veinlets and immediately adjacent country rock. Grade Control utilises two 4 m 'collar' samples which are collected from each 8 m production blasthole. The irregular distribution of the quartz veins and erratic gold mineralisation has resulted in a disseminated 'salt and pepper' type of gold occurrence, with only a poorly defined footwall. Delineation of ore and waste blocks for mining uses an approach which combines the smoothing effect of kriging with a pragmatic view of the raw data. Large ore blocks with simple geometry help to minimise mining dilution, reduce block variance and give good reconciliations to interpreted ore tonnes and grade. Daily mine face advance is reported against truck counts and provides continual comparison with budgeted production. All data processing uses Gemcom software, together with Lotus spreadsheets.

Jan 1, 1994

By E ¦iftti, A Koenig

Natural sphalerite associated with copper, silver, lead-zinc, tin and tungsten deposits from various world-famous mineral deposits have been studied by cathodoluminescence (CL), laser ablasion inductively coupled plasma mass spectrometry (LA-ICP-MS), electron probe microanalysis (EPMA) and electron paramagnetic resonance (EPR) to determine the relationship between trace element type and content and the CL properties of sphalerite. In general, sphalerite produces a spectrum of CL colour under electron bombardment that includes deep blue, turquoise, lime green, yellow-orange, orange-red and dull dark red depending on the type and concentration of trace quantities of activator ions. Sphalerite from most deposits shows a bright yellow-orange CL colour with lmax centred at 585 nm due to Mn2+ ion, and the intensity of CL is strongly dependent primarily on Fe2+ concentration. The blue emission band with lmax centred at 470 - 490 nm correlates with Ga and Ag at the Tsumeb, Horn Silver, Balmat and Kankoy mines. Colloform sphalerite from older well-known European lead-zinc deposits and late Cretaceous Kuroko-type VMS deposits of Turkey shows intense yellowish CL colour and their CL spectra are characterised by extremely broad emission bands ranging from 450 to 750 nm. These samples are characterised by low Mn (<10 ppm) and Ag (<1 ppm), and they are enriched in Tl (1 - 30 ppm) and Pb (80 - 1500 ppm). Strong green CL is produced by sphalerite from the Balmat-Edwards district. Amber, lime-green and red-orange sphalerite produced weak orange-red CL at room temperatures, with several emission bands centred at 490, 580, 630, 680, 745, with lmax at 630 nm being the strongest. These emission bands are well correlated with trace quantities of Sn, In, Cu and Mn activators. Sphalerite from the famous Ogdensburg and Franklin mines exhibited brilliant deep blue and orange CL colours and the blue CL may be related to Se. Cathodoluminescence behaviour of sphalerite serves to characterise ore types and help detect technologically important trace elements.

Jan 1, 2008

Callide Coalfields produces a sub-bituminous, very subhydrous, low rank, steaming coal with good combustion properties, primarily for domestic power generation. Geological input into planning of coal extraction requires expedient production of detailed structural, lithological, analytical, geophysical and geotechnical data. The CSIRO-developed SIROLOG borehole logging software and hardware system allows for detailed spectrometric analysis of coal/interburden. The gamma-gamma and neutron-gamma SIROLOG techniques both provide improved prediction of ash content over other borehole techniques. The neutron-gamma technique also predicts density and some important ash constituents (especially iron, alumina and silica). The software/hardware configuration allows for quick, easy interpretation of coal seam depth and lithology, parting thickness and ash/ash constituent contents immediately after a borehole has been logged. Within certain mine areas in the Callide Basin, the iron content of mined coal is widely variable in both vertical and lateral extent within and between seams. This variability creates problems in predicting the slagging behaviour of æas-receivedÆ coal during combustion, especially where the iron content of the ash exceeds 19 per cent. Using the SIROLOG tool in co-operation with traditional borehole sample laboratory analysis results, patterns in this variability can be determined and related to geological properties and process of formation of the coal seams. Subsequently, areas of high iron can be predicted in advance of mining. Since 1992, on-going collection and interpretation of SIROLOG downhole geophysical log data has significantly contributed to a number of research projects related to gaining a preliminary understanding of the iron distribution and formation during the Coal MeasuresÆ deposition. Because the probe was able to record variations in coal mineral matter content, it was found to complement more conventional techniques such as reflected light petrography, X-Ray Diffraction and SEM techniques that examine the mineralogy of iron species. Additionally, software has been developed to allow integration of SIROLOG data into existing geology databases, enhancing coal quality modelling and daily prediction of parameters such as raw ash, silica and iron contents that are indicators of ash fusion propensity. The correlation of SIROLOG-derived iron geophysical traces between drillholes and other sample points highlighted lithological and structural controls in the iron distribution in the sequence previously not detected. This work has allowed the development of a methodology for predicting iron in advance of mining and reconciling as-sold coal quality to that predicted. Predictions are currently being assessed at the coal face as mining progresses through high-iron zones.

Jan 1, 2000

A new gold cyanidation assay technique has been proven for a range of ores, where it has demonstrated benefits of being: ò Accurate (reduces the typical range of assay scatter almost three-fold, and avoids common fire assay interferences). ò Fast (under one hour, providing a quantum shift in space requirement and equipment utilisation each bottle roll can provide over 15 determinations per day). ò Simple (suitable for field application, no high skill or experience requirements). ò Profitable (reduced drilling, drilling time, ore misclassification and/or double handling after mining). ò Cheap (far lower cost than Fire or Aqua Regia Assays, ie LeachWELLTM costs around 10ó for a 20 g sample at 50 per cent solids, proportionately greater for larger samples eg $1 for 200 g samples which address most nugget effect problems). ò Relevant (distinguishes economic. ie cyanide-extractable gold, the only unequivocal value to use for true resource definition, mine planning and grade control). ò Robust (rough bucket chemistry of samplers does not seriously affect results). A new development is the provision of LeachWELLTM CAS, a solution, which also contains optimum cyanide and stabiliser concentrations; and offers greater: ò Safety (the dilute cyanide solutions are stabilised to avoid generating toxic HCN vapours; and present no cyanide dust or flying chips to deal with). ò Ease (a single squirt dispenses precise quantities of the entire reagent suite, avoiding multiple weighings). ò Reduction in total reagent costs. An inter-laboratory comparison on nine ore types, using two assay techniques (Fire Assay and Aqua Regia) involving 45 laboratories, has demonstrated that LeachWELLTM 60X assays for the samples tested, were equally or more reliable than typical Fire or Aqua Regia Assays. There is particularly great benefit in applying LeachWELLTM 60X assays to richer ores in comparison to Aqua Regia assays, which appear to be prone to very significant underassaying depending on individual analyst skills, and which often suffer greater nugget effects. The major impacts for heap leaching are that: ò Using the LeachWELLTM assay technique for grade control, ore of marginal grade is not accidentally discarded to waste or visa versa due to the scatter of assay data inherent in typical small charge (25 g) fire assays. ò LeachWELLTM assays very importantly report only that gold which will be recoverable in the heap, viz that which is liberated - an important factor where the coarse crush often leaves ten per cent of gold unliberated. These impacts are of particular importance for many ores (ie most of those recovered from open pit operations and at the margins of rich ore subject to slurry processing) subjected to heap leaching as the oxide zones often present major problems of nugget effects as well as mineralisation that cannot be accurately assigned through interpretation of clear structural controls.

Jan 1, 1994

Iron and steelmaking slags have been utilised for a century. All dumps are now exhausted. Because of constraints in establishing new stock yards, all slags have to be utilised immediately. At present, this is being achieved. Only in a situation where there is an increase in pig iron and crude steel production, together with the impact of new residual materials competing from other industries can marketing problems be anticipated.

Jan 1, 1979

At Renison Limited, on the West Coast of Tasmania, modern trackless decline mining is practised to exploit the various tin bearing sulphide deposits. With footwall accesses, one of three adaptations of horizontal mechanised cut and fill, 1. unsupported, 2. pillar supported,and 3. unsupported - resuing is used to stope each defined ore block. The stoping method is basically determined by the dip and true thickness of the ore with emphasis on high ore recovery. Extreme flexibility is possible by the selective mining of stope lifts, the consumption of development waste as fill and the utilisation of the same mobile equipment in all phases of production. This has resulted in high productivity and low cost per tonne of ore.

Jan 1, 1977

By M Ljunggren, M Lundh

Dissolved air flotation (DAF) in wastewater treatment as a separation process of submillimetre biological flocs is based on the generation of bubble/floc aggregates. DAF is a complex process but has got advantages, such as allowing a high hydraulic load, compared to sedimentation. A thorough knowledge of the physics of the DAF process is, however, still lacking. This paper will present results of experimental studies on three aspects of significance to the separation process û the flow structure in the flotation tank, rise velocities of aggregates, influence of floc size on the separation efficiency. Flow structure. Measurements were performed in a pilot plant mapping and visualising the velocity field. The dispersion water (bubbles) had a decisive influence on the flow structure due to the effect of the bubbles on the bulk water density. Stratified conditions with a less dense, bubble-containing upper layer and a clear water, denser bottom layer were important for a good separation. A simple model of the stratified flow structure was elaborated making it possible to interpret the function of the aggregate rise velocities. Bubble/floc aggregates. The dynamics of single flocs, bubbles, aggregates were visualised using a borescope + CCD video camera + digital recorder + image analysis. Sequences of video frames made it possible to determine the rise velocities of the single aggregates. These velocities were found to be in the range 1 - 9 mm/s with a tendency for large flocs to have higher rise velocities. Separation versus floc size. The floc size distribution was measured in the DAF process. Data from three different DAF cases showed, that large flocs (> about 100 ¦m) were entirely separated, whereas small flocs experienced a less good separation. It was, moreover, found, that a very significant separation of flocs took place in the very upstream end of the separation zone in a pilot plant case.

Jan 1, 2005

Interest in the sampling of refined copper cathodes has heightened over the last ten years. This has followed the increasing importance of cathodes as the principle trading form for metallic copper. It has also been given impetus by recent trends for quality certification of manufacturing inputs, specifically the AS3900 and IS09000 series of standards.

Jan 1, 1976

By Jifan X, Yongyu W, Liangjing L

Shallow interception of groundwater is a special dewa- tering form in the specific geological and hydrogeological conditions. It has an economic and technical effect. The roof of the Fankou Lead-zinc deposit is the Hutianqun aquifer made up of the limestone of the upper Carboniferous system. - A "water-bearing basin" is surrounded by the aquifuge and the aquitard below ¦0 m level at the Shiling Hill section in the Hutianqun aquifer. Based on the natural conditions, an interception gallery is excavated at -40 m level out of "the water- bearing basin", the other gallery excavated at ¦0 m level in the poor water-bearing zone of the Jinxing Hill. During 20 years of experience, the better interception effects have been gained.

Jan 1, 1988

A test model is presented for the simulation of dewatering by gas injection of a porous aquifer above longwall workings. A finite difference model used in the oil industry was modified to match the underground mining conditions. The model is suitable to cope with the problem of dewatering reservoirs of low transmissivity. After comparing more versions, it has been concluded, that the investigated dewatering method can be proposed under special hydrogeological conditions only.

Jan 1, 1988

By Balks AI

Systematic roof bolting in Australian coal mines began at Elrington Colliery in 19)49. Since that time the proportion of the roof supported by roof bolts has increased until, in 1970, 1.5 million were installed in Australian coal mines. This rapid growth of roof bolting has meant that the range and variety of roof bolting machines has altered also. The-number of machines now available both to bore holes and place roof bolts has increased. to the point where both rotary and per- cussive machines are used extensively. Generally, until the last four years, roof bolting machinery in Australia followed the practices in vogue in the United States. However, in -recent time the particular problems of Australian coal mining have necessitated the development of equipment primarily suitable to Australian conditions.

Jan 1, 1971

The factors affecting performance of base and precious metal smelting and converting processes are considered in relation to reactor characteristics. The chemical differences between processes are related to these factors for different reactor systems. The complete smelting and converting flowsheet involves a number of operations. The process selected for a particular feed and product requirement should be one which optimises the efficiency of the process, the cost of building and operating the technology and the long-term maintenance and productivity of the units.Ausmelt's approach to achieving an efficient process using its technology is described in relation to the smelting of copper concentrates for production-of blister copper.

Jan 1, 1992

By George G

The Circum-Pacific Map Project is a cooperative international effort to prepare and publish geological, geophysical and mineral resource maps of the Pacific Basin and adjacent land areas. Earth scientists representing 180 organizations from more than 40 Pacific Rim countries are participating in the work. The project is directed by a committee established 14 years ago as an activity of the non-profit Circuin-Pacific Council for Energy and Mineral Resources. Technical and cartographic support is provided by the U.S. Geological Survey. The Circum-Pacific Map Project is organized under five regional panels of experts on the geology and resources of the four quadrants of the Pacific and Antarctica. A series of five 1:10,000,000-scale regional maps and a 1:17,000,000-scale map of the entire Project area, the Pacific Basin Sheet, provide the cartographic base. Forty-eight individual sheets are planned and thirty have been published in eight different series, including base maps, geography, plate tectonics, geology, energy resources, mineral resources, tectonics and geodynamics. Additional special single-sheet thematic maps on the Pacific Basin base have been published and are planned for a total of more than 50 individual sheets.

Jan 1, 1987

By T Baumgartl, T Huynh, K Tungpalan, E Wightman, M Edraki, M Tayebi-Khorami, L Huang, S Palaniandy, E Manlapig

With the increasing rate of tailing production worldwide there is a growing concern about the hazards of tailings storage facilities (TSF). Past and current mining, processing and waste disposal strategies that focus on the extraction of the valuable minerals, and an economic assessment only, are no longer suitable. Social implications and environmental legacies must be included for effective evaluation. This is possible by using an integrated assessment framework to evaluate more alternatives, including the production of additional saleable and benign streams, alternative tailings treatment and disposal as well as options for reuse, recycling and preprocessing of existing tailings. Tailings are not viewed as a final waste product but as part of the resource. From the sustainability perspective the models developed in integrated research programs will contribute to more effective methods for assessing different scenarios and potential processes and lead to better environmental management, increased production of benign tailings and improved efficiency of water and energy use and thus more responsible resource stewardship of the ore resource.This paper presents preliminary results from a multiyear research program on integrated tailings management at the Sustainable Minerals Institute (SMI), The University of Queensland, called ‘Designer Tailings’. The project involves the gathering of experimental and observational information on tailings biogeochemical processes to design and modify the range of activities within mineral processing plants, upstream characterisation ore and gangue, and downstream tailings management for desired tailings properties and outcomes. This information will assist the development of new total integrated value chain CITATION:Edraki, M, Huynh, T, Baumgartl, T, Huang, L, Andrusiewicz, M, Tungpalan, K, Tayebi-Khorami, M, Wightman, E, Palaniandy, S, Manlapig, E, Evans, C, Farrokhpay, S, Bradshaw, D and Vink, S, 2014. Designer tailings – an integrated model for tailings management, in Proceedings Life-of-Mine 2014 , pp 599–608 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Reid T. W

This paper describes the results of investigations into the relationship between specific gravity and chemical composition in the Cockatoo Island orebody, In the early investigations the samples were classified into groups according to porosity. This resulted in high, medium and low porosity groups, the latter being further subdivided into ore and waste. Whole number tonnage factors were assigned to each group. In the later investigations the reciprocals of bulk specific gravity and true specific gravity were ex- pressed as linear combinations of iron, silica and alumina using stepwise regression. The efficiency of the models as predictors was tested by dividing the data into two sets; one of which was used to calculate the regression equation and the other to test the efficiency of the equation as

Jan 1, 1976

Two significant TBM boreability predic- tion models are outlined. Predicted advance rates are compared with actual advance rates taken from twenty case histories. The results show that a simple low cost method that uses one machine parameter and one rock parameter compares very favourably with a high cost sophisticated method which also includes information regarding discontinuities in the rock mass. The effect of rock texture on drillability is also examined. A method of quantifying rock texture has been developed and is outlined. Experimental results show that the developed TEXTURE COEFFICIENT returns highly statisti- cally significant correlations with drilla- bility data in a wide range of rock types.

Jan 1, 1987

The Mine Safety and Inspection Act, 1994 of Western Australia recognises the importance of ground control in underground mining. The recent safety performance of underground mining is summarised in terms of the most common causes of injury and fatal accidents. A review of current ground control practices is presented and the concepts of local and large-scale ground control are introduced. The need for a more systematic approach to ground control is considered to be directly related to requirement to improve safety performance. The new regulations will require that certain geotechnical issues be addressed during the life of a mine. To comply with the regulations it is suggested that a ground control management plan be developed for each mine. The geotechnical issues associated with the ground control management plan are reviewed and hazard recognition aspects discussed.

Jan 1, 1995

By Swann CA

In order to meet export sales requirements from 1983 onwards, Amcoal developed a new underground mine in the Witbank area of the Transvaal. The mine was required to produce 5 million tons of run of mine coal per annum giving rise to 4 million tons of saleable products. A description of the coal processing plant is given with comments on design philosophy and design parameters. Main features of the coal processing plant are the raw coal handling facilities, centralised control and data capture and the loadout station. The management systems applied during the commissioning period are described. The difficulties experienced and their solutions are discussed. Commissioning was concluded with an independent plant performance test.

Jan 1, 1986

The last decade has seen a dramatic change in the. size and complexity of mining and mineral processing projects in Austral- asia. Major projects of today are vastly different from major projects of the 19.50's. This change has in turn resulted in a change in the role-of consultants whose contributions have been increasingly in the provision of specialist services and less in the form of overall project design and construction supervision. It is anticipated that, the specialist function will continue to represent the principle mode for consultant participation in major, projects. However, by means' of international affiliation, the development of comprehensive engineering and project management capabilities and possibly as a result of Government intervention, it is expected ,that local consultants will assume an increasing degree of participation in.the overall project design and supervision Function.

Jan 1, 1975