Search Documents

The metals titanium and zirconium and their alloys occupy individually unique positions in the catalogue of metallic materials available for engineering applications. Because of the uniqueness of their usage in the aerospace industry, in the case of titanium, and in the nuclear industry, in the case of zirconium, the except- ional resistance of both the metals to the majority of corrosive media is often overlooked. The cost factor in the application of these more exotic metals has, in the past, been a major considerat- ion in the rejection of titanium and zirconium as constructional materials in areas of usage where their superior corrosion resistance strongly favoured them over more conventional metals and alloys. The cost differential, vis-a-vis austenitic stainless steels, for example, is not a trifling matter, being of the order of 6 : 1, when compared on a weight basis. However, if one considers the cost, for, say, sheet product on an area basis, the ratio is redgced to approximately 3.4:1. If one also takes into account the enhanced performance of the more expensive material and the sub- sequent increase in service life and decrease in plant down-time, the economics of the usage of materials such as titanium becomes much more attractive and, indeed, highly competitive,

Jan 1, 1969

By Aziz N. I

Examination of the geology and support performance at two site leads to development of an under tanding of the influence of caving on powered support rating. The two site represent the current extremes in support rating, i.e. 6/260 tonne supports operating in the Hirst seam at Solsgirth Colliery, Scotland, and 4/900 tonne supports operating in the Bulli seam, West Cliff Colliery, Australia.A conceptual model considers the coal ahead of the face, the powered support, and the caved waste to be three yielding foundations which interact to control the subsidence of the roof strata.The caving mechanisms identified for the strata of the Hirst and Bulli seams, are different. These mechanisms being related to rock properties - the palaegeography and depositional conditions at each site-produce caved wastes with different yield characteristics.An analysis of the results obtained for convergence and support reaction during production cycles at both sites shows the manner in which support reaction is developed, indicating the importance of higher setting load densities in the Bulli seam.Evaluation of the work done on the subsiding roof strata during typical production cycles by two of the yielding foundations the powered support and the caved waste immediately behind the powered support - further demonstrates the influence of caving mechanisms on support rating.

Jan 1, 1989

In late 1987 it was recognised that column flotation might have potential for improving the grade of the zinc concentrate produced at Pasminco's South Mine in Broken Hill. Intermittent test work was carried out during 1988 using a 90 mm diameter by 6 m high perspex column, built and initially operated by staff from CRA Advanced Technical Development. This column was found to have insufficient retention time so, during the first half of 1989, Pasminco constructed and installed a 200 mm diameter unit of the same height. Extensive testwork was carried out using this column during the latter half of 1989 and early 1990. It was clear from the results that a grade improvement of between 1 and 2 per cent (absolute) would be achievable. The effect of column cleaning on overall recovery was not established with the same degree of confidence, so the proposed new circuit is to include one of the existing banks of OK8 cleaner cells as a scavenger on column tailings. The test work provided sufficient data for preliminary design work to begin in May 1990 and commissioning of full scale zinc cleaner columns is planned for mid 1991. This paper summarizes the results and describes some of the experiences with column flotation at the Pasminco South Mine.

Jan 1, 1991

By Hinrichsen H. D, Rathburn D. R, Stieger W

The present situation in the field of iron ore pelletizing is briefly described with particular view of the Lurgi/Dravo travelling grate process. To meet todays pellet quality requirements with regard to physical and metal- lurgical properties it is often necessary to add basic fluxing materials. It has been de- monstrated that for certain ores, basic addi- tives provide a considerable improvement in fired pellet quality. The production of self- fluxing pellets is becoming increasingly attractive. One Lurgi/Dravo plant is now in operation and another is under construction which were designed for the production of self- fluxing pellets. Self-fluxing pellets may be considered as the primary or exclusive blast furnace burden and the installation of a sinter plant is not necessary if the pellet plant-can handle all in-plant fines. Reference is made to the first pellet plant utilizing iron ore concentrate, in-plant fines and basic flux. The use of solid fuel for pellet indura- tion is discussed because of the increasing prices and possible shortages of heavy oil and natural gas. Since there is a strong tendency to increasing plant capacities, the design fea- tures of travelling grate pelletizing plants for productions up to 6 million tonnes are Discussed.

Jan 1, 1974

THE object of this paper is to offer some suggestions to assist metallurgists to supervise the operations of flotation plants. We do not yet thoroughly understand what "flotation" is or "why minerals float" and all attempts that have been made to explain the phenomena have been based on theory or imagination, and have not been capable of substantiation by practical demonstration, or even by laboratory tests; but it is wellknown that particular minerals will float in a liquid under certain specified conditions, and that some other minerals will not float under those conditions, and that, if a mixture of the two classes of minerals be subjected to those conditions, there will be separation of the minerals, of which one class will float and the other will remain unfloated as a residue. The duty of the flotation expert is to so control the operations and the conditions of the liquor as to obtain the best commercial result from the ore he is treating. The chief controlling factors in a flotation plant appear to fall under the following eight headings, all of which are important:1. Crushing.2. Rate and regularity of feed.3. Density of pulp.4. Temperature.5. Addition agents.6. Condition of circuit liquor.7. Agitation.8. Aeration.

Jan 1, 1920

By K Kinnunen

A strong correlation between the reduction degradation index (RDI) of production sinter and the titanium content of the sinter mix was identified at the Ruukki sintering plant between 2000 and 2004. The titanium distribution in different mineral phases was studied using samples from pot sintering tests. Titanium additions were made using two different materials: rutile and crushed titanium-bearing haematite pellets. While both titanium additions clearly increased the RDI, titanium seemed to favour secondary haematite. The study focused on the effect of titanium in haematite, because haematite is reduced to magnetite in the RDI test. During the haematite-magnetite reduction, reduction degradation was observed. To increase accuracy, the phenomenon was investigated first by sintering and then reducing synthetic minerals under controlled laboratory conditions at the University of Oulu. The effect of titanium oxide in solid solution in magnetite on the magnetite to haematite transformation rate was studied first in order to simulate the final stage of the sintering process. In other experiments, haematite samples doped with 0.5, 2.0 and 5.0 wt per cent titanium oxide were studied using thermogravimetry under a controlled gas atmosphere (CO/CO2/H2/N2). Sintered samples were reduced using the same gas composition as in the RDI test. Polished sections for optical microscopy and SEM-EDS analysis were prepared from both reduced and oxidised samples and unreduced sintered samples. The titanium oxide content of haematite had a clear effect on reduction degradation of the samples. Furthermore, increasing titanium oxide content in solid solution in magnetite radically accelerated the oxidation rate. Similar observations regarding the effects of titanium have been reported earlier, but this was the first time the effect of very small additions of titanium were shown to deteriorate blast furnace burden quality and a reason suggested behind the process.

Jan 1, 2007

By Ritter K-C, Sturgul J. R, Filess T

The proposed Lihir open pit gold mine is located on Lihir Island in New Ireland Province, Papua New Guinea. The mine will be located within a volcanic caldera, part of which forms the adjacent Luise Harbour. Kennecott Corporation started engineering design work in 1988 and ended in 1993 when a Feasibility Report was submitted to the Papua New Guinea government by RTZ/Kennecott. The project will be managed by the Lihir Management Company. The mining operation will produce approximately 350 Mt of waste and 62 Mt of low-grade ore over the life of open pit mining. Landforms and traditional land use by Lihirians preclude storing mine waste and some of the low-grade ore on land close to the mine site. The mine waste will be composed of hard rock and soft soild like material which cannot be safely used to construct large land waste repositories by truck dumping. Submarine disposal by bottom discharging barges is the only safe disposal method. The barges will also be required to construct a waste platform along the shore for stockpiling low-grade ore. A simulation model of the waste handling system was written in GPSS/H¦ to assist engineers in selecting the optimum size and quantity of barges and loading docks by analysing the interaction between excavators, trucks and barges. The simulation model was written in enough details to model the various functions that will be encountered during mining. Input parameters allowed for variations in the size and number of trucks, shovels, barges and loading docks. Variations in loading, hauling, and dumping times were from user specified distributions. In order to visualise the interaction between the components of the waste mining operation, the simulation was animated using Proof AnimationT""'. It is believed that this is the first application of an animated simulation study for a mine still in the planning stages.

Jan 1, 1995

By F J. Rios

In the eastern high-strain domain of the Quadrilßtero Ferrffero, Brazil, hard and soft high-grade hematite ore may occur as schistose bodies in shear zones mainly related to the Cambotas-Fundpo thrust system. These orebodies are almost entirely constituted of oriented specularite platelets that develop both as a product of crystal-plastic deformation of hematite and solution-precipitation processes. Both mechanisms interact in the partitioning of the strain, while solution-precipitation is responsible for the precipitation of hematite and localised leaching of silica resulting in the formation of syntectonic ores. The analyses of fluid inclusions from specularite crystals of the Conceitpo and Timbopeba deposits, located in the northern and southernmost areas of the eastern high-strain domain of the Quadrilßtero Ferrffero, were studied using infrared microthermometry and Synchrotron x-ray fluorescence. The results indicate the participation of highly saline aqueous H2O-NaCl fluids containing other additional cations (Ca, Fe, K and probably Ti) in solution and homogenisation Temperature (Th) averaging between 130¦ - 190¦C. However, the partial fusion of metastable saturation phases indicates crystallisation temperatures of approximately 400¦C. The mineralisation process produces high-grade orebodies as well as Fe-rich specularitic itabirites that are explored in that area. The shear zones are related to thrust faults mapped and interpreted as related to the PanAfrican/Brasiliano Orogeny that affected the Quadrilßtero Ferrffero, thrusting the Paleoproterozoic platform sequence of the Minas Supergroup over Mesoproterozoic quartzites of the Espinhato Supergroup. They intersect and even overprint an early metamorphic and tectonic fabric of Paleoproterozoic age (Transamazonian Orogeny). The geological and fabric relationships lead to the conclusion that the fluids involved in the mineralisation were most probably of external origin, of still unknown source (possibly igneous), during the closure of the Spo Francisco Craton.

Jan 1, 2005

By Y Mita, T Iwama, R Inoue, S Ueda

In the iron and steel manufacturing industries, efforts are being made to achieve carbon neutrality by 2050, and the transition from a coal-based steelmaking process to that utilising renewable energy is being pursued. An alternative process in which directly hydrogen-reduced iron is melted in an electric furnace is being investigated. It is known that foaming slag reduces heat loss from the steel bath in electric arc furnace, but iron loss due to the suspension of steel particles in the slag is indispensable. To improve the separation of steel particles from the slag, the control of the slag viscosity is important. Although the slag viscosity has been extensively studied, in those studies the slag was considered to be a simple liquid. However, in actual operations, slag is a multiphase fluid consisting of solid, gas and liquid phases. Therefore, in this study, by measuring the sedimentation velocity of titanium, stainless steel and glass spheres in an aqueous glycerin solution containing bubbles generated by the reaction between NaHCO3 and C2H2O4, the apparent viscosity of the gas-liquid fluid was evaluated based on Stoke’s law. It was found that the apparent viscosity of the gas-liquid fluid is larger than the viscosity of liquid phase and depends on both the bubble volume ratio in solution and the density of the falling solid sphere, and the apparent viscosity was different from that previously obtained by the rotation method. The apparent viscosity derived from the sedimentation velocity of solid spheres changed depending on the specific gravity of the ball. This is because the apparent viscosity is derived from the velocity of a ball falling in a static bubble in this method, whereas that is derived from the force applied by a stationary flow in the rotational method.

Aug 21, 2024

The constructionhunnelling industry in Hong Kong has taken an upturn during the last few years due to the commencement of works to relocate the International Airport to Chek Lap Kok Island. The Airport Core Program consists of ten individual projects including roads, landfill, bridges and tunnels to build the airport and link it to the mainland of Hong Kong. Part of one of these projects is Cheung Ching Tunnel located on Tsing Yi Island. The proposed tunnel consists of a 1.6 km twin tube road tunnel through the island's central ridge, taking three lanes of traffic each way. Each tunnel is 16 m wide - (the widest road tunnel in Hong Kong) and are 10 m high. ICI Explosives (China) saw an opportunity to supply bulk explosives to the Cheung Ching tunnel and contacted ICI Australia to determine availability of a bulk system for tunnel blasting, and assist in its introduction. This paper discusses the methodology behind developing that bulk system to suit a large tunnel drill and blast operation. It also looks at the problems encountered along the way, from the development of the product to the application of the system in the tunnel and the eventual success of introducing a bulk system into a large tunnelling project.

Jan 1, 1994

By A Bennett, A Peck

BHP has recently constructed a Hot Briquetted Iron Plant at Port Hedland in the Pilbara region of Western Australia. Supply of iron ore fines to the plant is by conveyor from the companyÆs existing Nelson Point stockyards. The conveyor passes under Port Hedland harbour in a concrete segmentally lined tunnel, approximately 1030 m long and with a 5.1 m external diameter. The tunnel was constructed by a Tunnel Boring Machine (TBM) which both excavated the ground and erected the tunnel lining. The tunnel was bored between cut and cover in situ concrete portal structures, the TBM being launched from the Finucane Island side towards Port Hedland town. The alignment required lengthy gradients of 1:6 on either side of the harbourÆs dredged channel, under which the tunnel is bored with a minimum clearance of 8 m.The tunnel is fitted-out with:1800 mm belt conveyor capable of 10 000 tph;walkway along which a specially designed inspection/ maintenance vehicle can run; andtunnel services including power, light, fire detection and suppression communications, water mains for wash down and sumps and pumps for drainage.This paper gives a general overview of the design and construct contract, important aspects of the design and the construction process itself.

Jan 1, 1999

By M Darby, B Burdett, F Lovell

The results of the process control improvement project aimed at improving the quality of Australian Bulk MineralsÆ (ABM) iron ore pellets produced by four vertical shaft furnaces are very positive. These results are achieved through process stabilisation and optimisation, improvement in process monitoring and taking early corrective actions when operating variables were outside the target ranges. A number of benefits are obtained from this project. These benefits include: More consistent and improved pellet quality. The average cold compression strength (CCS) value of pellets produced during the eight-month trial is 260 kg/pellet, which is 16 kg/pellet higher than that produced during the 12 months prior to the trial (244 kg/pellet). Reduction in the heat input by eight per cent, from 727 MJ/tonne to 668 MJ/tonne. Reduction in bentonite rate by six per cent, from 7.1 kg/tonne to 6.7 kg/tonne. Increase in the furnace throughput rate by four per cent and additional production of 10 000 tonnes per annum through process stabilisation. Better understanding of the process behaviour. This knowledge is valuable not only for setting the target operating conditions but also for developing the ABM expert system to control the process.

Jan 1, 2005

Tomago sandbeds is an unconfined coastal aquifer located 20km. north of Newcastle in New South Wales, Australia. These sandbeds extend over an area of about 130km. The average aquifer depth is about 20m. with a mean transmissivity of about 400sq.m/day and a specific yield of about 0.2. The city of Newcastle and surrounding areas derive water from Tomago for potable purposes. The average extraction being about 50 ML/day. The iron value of the ground water varies between 5 and 15mg/1. This iron is removed by a conventional water treatment plant using Alum. The aquifer whilst principally quartzose also contains deposits of heavy minerals like rutile, zircon, ilmenite, etc., The mineral sand mining has been in progress at Tomago since 1972. Mining is carried out in a con- structed pond with a water depth of about 5m. on which is floated a suction cutter dredge that moves across the front of the pond using a water jet to entrain the soil from the ground surface to the bottom of the mineralised zone. Effect of mineral sand mining on ground water quality, particularly iron, was the subject of intensive investigations undertaken at Tomago since 1970. The effect on water quality was studied by collecting and analysing water samples from network of observation wells established during the period of mining. Water samples were collected about 4-5 years prior to mining and analysed for iron, sulphate, chloride, pH, etc., After mining the observation wells were re-established at the same locations and water samples were collected and analysed for at least 5 years after mining. Water samples collected from majority of the observation wells indicate an increase in iron levels. The level of increase is very site specific. The increase in iron is also

Jan 1, 1987

The mill area of PT Freeport Indonesia is located in a valley surrounded by steep natural slope, characterised by extreme topography with mountains rising to above 4500 m within 100 km from the seashore. The valleys are deeply embedded into the mountainous terrain and bordered by steep natural slopes. Vertical or overhanging lime walls are interrupted by steep vegetated screen sections containing accumulated loose material from weathering processes and ancient rock falls and/or debris flows/avalanches. The climate can be best described as alpine subtropical with an accumulated rainfall of more than 5000 mm per year. Occasional snowfalls and superficial freezing above 4000 m elevation leads to heavy weathering of the superficial rock layers and along open joints and fractures. The mill area is a crucial and strategic infrastructure for the entire mining operation which is best characterised as a high density industrial area with facilities including water tanks, power generators, crusher, and concentrating facilities including office buildings and workshops as well as access tracks to the underground mining blocks. Considering the local topography, the restricted space conditions and the number of technical installations, the facilities are likely to be affected and highly vulnerable to rock fall from the surrounding slopes. In order to minimise the rock fall hazard three rock fence barriers area were constructed at the mill area. The 7.5 rock fence barriers were designed with the maximum capacity of 5000 kJ. These are the largest capacity of rock fall barriers ever constructed in Indonesia. The total length of the barriers for the three locations was 126 m. The biggest challenge of this project was the construction of the barrier at West Gulley, which was constructed at 300 m above ground level. For this site, construction access was undertaken using helicopter. This presentation discusses the design of the mitigation structures as well as the construction approach and stages of the barriers. Please note: This paper is abstract only.

Nov 25, 2010

The detailed work done by Stillwell and Edwards on the occurrence of cobaltite and safilorite-Iollingite at the South Mine, followed by its presentation as a paper to the Institute, calls for, a few notes on its occurrence elsewhere in the Broken Hill field. No massive cobaltite similar to that in the South Mine veinlet is known except from the Consols Mine (as mentioned in the paper). Fine grained cobaltite has, however, been found in low-grade ore from the North Mine. Microscopic grains occur in a mineralized green feldspar pegmatite. The feldspar has been replaced in part by graphite, and the cobaltite occurs in association with the graphite. In its hardness, pinkish-white colour, and resistance to the standard etchingqeagents it is similar to the South Mine cobaltite; it is etched by acid permanganate solution. An interesting feature of this occurrence is the way in- which some of the minerals (notably galena) have forced apart the graphite lamellae in crystallizing, forming lenses enclosed by the curved cleavage surlaces 0;[ the graphite.StillwelI and Edwards cite a note by G. Smitht for the statement that "cobaltite has been recorded from the Australian Broken Hill Consols Lode in the vicinity of the rich silver deposits, though not in contact with them."Smith, however, is here referring to the oxidized zone. Elsewhere in the same article he states "... a deposit of cobaltite in a very much altered condition was found. This was impregnated with silver, and assayed as high as 3,000 ounces," Of the cobaltite in the unoxidized zone, Smith simply states that it became rarer with depth.Cobaltite has also been recognized by Mr. H. F. Whitworth, M.SC., Curator of the Mining Museum, Sydney, in specimens from Burt's Copper Mine eight miles south of Broken Hill.

Jan 1, 1944

By M I. Pownceby, N Karimian, A Frierdich

These may be found with goethite through mechanisms including direct substitution or coprecipitation of nanocrystalline phases. Understanding P incorporation in goethite has significant implications for Australia’s iron ore industry as it lowers their commodity value. The current study tests a novel low-temperature technique to extract P impurities from synthetic goethite phases under O2-free ambient conditions by utilising Fe(II)-catalysed recrystallisation. The objective of this study was to examine the effect of the Fe(II)-catalysed recrystallisation of goethite on the geochemical behaviour (mobility and speciation) of co-associated P. To achieve this, we tracked changes in labile P (aqueous and 1M NaOH extractable) concentrations over time in goethite suspensions which were reacted with Fe(II)aq for 14 days under circumneutral pH conditions and room temperature conditions. Temporal changes in Fe mineralogy were investigated via synchrotron-based X-ray absorption spectroscopy. Iron K-edge extended X-ray absorption fine structure (EXAFS) spectroscopy confirmed goethite as the only mineral phase in P-free treatments while goethite (~86 per cent) and feroxyhyte (~14 per cent) were the main phases in 1.0 per cent P-containing treatments after a 14- day reaction with Fe(II)aq. According to our findings, the treatment of P-goethite with Fe(II) for a duration of 7–14 days, followed by a 24-hour extraction of the reacted solids using 1M NaOH, results in the removal of approximately 79.5 per cent of the initial P content. This removal encompasses both the aqueous fraction (~4.5 per cent) and the surface adsorbed fraction (~75 per cent) from the 1 per cent P-bearing mineral phase. Notably, this approach demonstrates an improvement in P extractability, with approximately a 10 per cent increase compared to the 1 per cent P-goethite sample that was not reacted with Fe(II).

Sep 18, 2023

By Denholm WT

The main objective of the experimental study was to investigate the dissolution kinetics of various forms of carbon under iron bath converting or smelting-reduction conditions, i.e., particulate, free moving carbon in contact with a turbulent iron melt. Iron/carbon melts were contained in cast magnesia-lined silicon carbide crucibles heated by a medium frequency induction furnace. The melts were stirred by injecting nitrogen through 2 mm I.D. alumina lances submerged to a depth of 50 mm in the 100 mm deep baths. Particulate carbon in the form of graphite, brown coal char and petroleum coke, were dropped directly onto the turbulent bath. The dissolution rates of the various carbon types were monitored by taking periodic bath samples for subsequent carbon analyses. The effect of carbon particle size (1-6.25 mm), the degree of bath turbulence (nitrogen stirring rates of 0-20 litres/min), and bath temperature (1300-1500¦C) were assessed. The analysis of the results was complicated by particle buoyancy effects, but it was established that the dissolution rates of the three carbon types investigated were similar, and increased linearly with increases in the gas stirring power inputs. Particle size had relatively little effect on the dissolution rates.

Jan 1, 1984

Gold mineralisation at the Kerimenge-Lemenge prospects is a classical example of myltiple, overprinting events, associated with intrusive-related hydrothermal systems. Repeated emplacement of high level dacitic porphyry bodies (Edie Porphyry; 2.4 - 3.8 Ma) was accompanied by a phreatomagmatic eruption which formed a diatreme-maar complex. Later hydrothermal fluids utilised permeable fault zones and diatreme contacts. Mineralisation took place during two main events. Stage I consists of early quartz - illite/sericite - carbonate phase with associated pyrite-arsenopyrite mineralisation. This phase is zoned from quartz - sericite-pyrite/arsenopyrite in the south at depth, to dominantly manganocarbonate - illitic clay - arsenopyrite- pyrite_s significant base metals in the north and at shallow levels. The majority of known gold (18.1 Mt @ 2.0 g/t Au) at Kerimenge is associated with Stage I activity. The gold occurs primary within the lattice of the sulphides and is metallurgically refractory. Fluid inclusion studies indicate early boiling and progressive cooling and dilution of hydrothermal fluids during the evolution of the Stage I event. Near paleosurface condensation of gases, which evolved off the boiling system at depth, produced abundant low pH bicarbonate fluids. During the waning phases of Stage I activity, these bicarbonate condensate fluids descended down permeable structures and formed banded manganocarbonate veins. High grade non-refractory gold mineralisation during Stage II event is restricted to favourable structures at relatively shallow levels and in the northern regions of the prospect area. Gold in this event exhibits a distinctive Au - Ag - Te -Cu geochemical signature, and is associated with hessite - tennantite - chalcopyrite mineralisation within quartz veining. Alteration and fluid inclusion studies indicate that this style of mineralisation is a result of the quenching of pulses of hot, late magmatic mineralised fluids by the cold condensate waters.

Jan 1, 1997

By J Zhou, D M. Hunter, S M. Iveson, K P. Galvin

The recovery and concentration of ultra-fine iron ore can provide significant economic benefits. Presently, there are limited options available given the low settling rates achieved by conventional gravity separation and the relatively poor performance of reverse flotation. The Reflux Classifier is a new water-based gravity separation technology that consists of a set of parallel inclined channels positioned above a vertical fluidised section. This arrangement promotes a powerful throughput advantage compared to conventional fluidisation and a highly selective hydrodynamic basis for achieving sharp separations. A high shear rate develops within the inclined channels, which generates sufficient hydrodynamic lift to convey the lower-density particles (even if they are relatively coarse) to overflow while retaining the high-density particles (even those that are ultra-fine) for discharge to the underflow. The technology has previously been used around the world on particle sizes in excess of 0.1 mm. The present work, however, is concerned with density-based separations down to much finer particle sizes approaching 0.01 mm.A major advantage of the Reflux Classifier technology is the achievement of simultaneous gravity separation and desliming via a single-stage separation. A series of continuous experiments was conducted using an iron ore feed with head grade of 35 wt per cent FeT and nominal top size of 0.106 mm, with 59 wt per cent being below 0.038 mm in size. At a low throughput of 1.5 t/(m2 h), the Reflux Classifier produced high-grade products at a high recovery. For the entire feed, grades of 66.1 wt per cent FeT with Fe recoveries of 80 per cent were achieved in a single-stage separation. Within the 0.020–0.038 mm size fraction, grades of 68.8 per cent were achieved with iron recoveries of 94.7 per cent. Excellent recoveries of up to 57.0 per cent were achieved for the -0.020 mm size fraction. The ability of the inclined channels to retain the fine dense material further enhances the effectiveness of the Reflux Classifier by creating an autogenous dense medium effect within the vertical section. This helps to elevate large gangue particles up into the overflow.CITATION:Hunter, D M, Zhou, J, Iveson, S M and Galvin, K P, 2015. Gravity separation of ultra-fine iron ore in the reflux classifier, in Proceedings Iron Ore 2015, pp 143–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

In attempting to vegetate pnob!em sites some basic pn.i,ne%ptes, namely the phys.ica.e and chemi.ca2 pnope/ti;es og the problem mateni.al and the selection oU hu.itab.2e p!antts {cor pnopagati.on, have to be considered. Pnobtem sites such as tai ing dams, mined-out atteas, and areas which have been genehaUy advehse2y a46eeted by mining activities, are not only o~ten located in a divehs.ity o4 climatic regions, but they also usuaUy dL64en substantially in theAjt .int' Lns c phys.ica2 and chem.i cat pnopen t i.es . To estabP.ish vegetation on such sites 6requent2y requites: .%) The ame Lonaton oU adverse {yaetors in onde t to exeate a hoot env.utonment suitable Uon "satis1actony" plant growth. .%i) These.2eationo4 plant species suited to the improved Hoot env.utonment, and eompat%b&e with the e2imate o{y the site, and the ultimate Land use o4 the site. iii) The estabL shment o{y a Laboratory and p-LLot scale testing programme to aeeomptizh the above.

Jan 1, 1976