Search Documents

By Lee H. G, Li H, Hayes P

Slag from the smelting of lead can contain up to 20 per cent zinc as an oxide. An understanding of the lead smelting process and of the subsequent fuming process for the recovery of zinc is enhanced by a knowledge of the activity coefficient behaviour of zinc oxide in smelting slags. The literature presents a wide range of contradictory values. This paper critically reviews the published data and outlines new measurements being made by the authors. A consistent set of zinc oxide activity coefficient data is presented for liquid slags within the ZnO-'FeO'-CaO-A1203-SiO2 system, through a combination of present and previous measurements.

Jan 1, 1993

By K Dagdelen

A vehicle proximity warning system is being developed using GPS and wireless local area networks to improve safety of off-highway trucks in open pit mines. After two an a half years of research, software development, and laboratory testing, field tests were carried out at operating limestone quarries and open pit mining operations to evaluate GPS accuracy and overall system effectiveness under rugged operating conditions. This article describes the progress made on this NIOSH funded project and discusses the GPS accuracy tests and overall system tests that were carried out during 2001 at the Morenci open pit copper mine in Arizona.

Jan 1, 2003

Western Mining Corporation began shaft sinking operations at it's Foster orebody, south of Kambalda, on the 20th June, 1984. The top levels of the orebody are currently being mined via a decline some 1.5km away.Long term plans require the shaft and decline to combine and produce 400,000 tonnes of nickel ore per annum. Eventually all of the ore produced will be hauled up the shaft.The shaft is 4.5m in diameter and the target depth is 760m. Ground conditions to date suggest there will be no further need for concrete lining beyond the oxidised zone. As such, the sink is an open-shaft development in competent basalt rock. Shaft furniture will be installed on completion of the excavation to the target depth.This paper summarises the experience in the project to date, along with comparisons to conventional shaft sinking methods employed in previous years at Kambalda Nickel Operations.

Jan 1, 1985

Coal slurry pumping was introduced into the U.K. in 1973. Gateside packs were prepared in areas of containment using R.O.M. coal and a special fast setting cement. The packs restricted roadway convergence and moderated spontaneous combustion risks, but costs were high and alternptives were sought. A similar system using OPC and an accelerator had limited success. Much more successful was the Aquapack process which used dilute slurries of a special OPC based cement and an accelerator based on sodium carbonate and bentonite pumped simultaneously into la fabric packbag. The Tekpak system using HAC and a much modified calcium sulphate mixture superceded Aquapack on the grounds of improved cement pumping life lower alkalinity and lower costs. A further modification of this system gave a cement with a 24 hour pumping life thus obviating flushing out pipe ranges except at the week-ends, improved packbags also increased the efficiency of the process. The hazard of spontaneous combustion can be inhibited if air supply channels across the waste can be located and plugged. Using gas samples from pack pipes to locate the heating and injecting a special grout, formulated from bentonite, sodium silicate and thixotroping agents. into the waste on the intake road has proved a successful method of controlling heatings. Mine' roadway and face cavities are being safely and successfully filled with cementitious foams produced in a novel placer machine. The foams are based on fast setting cements with specialised foaming agents. Up to 13 cu. metres per hour of fast setting thixotropic foams can be produced and their use is now widespread throughout U.K. coal mines.

Jan 1, 1986

By A N. Terblanche, D S. Smit

The paper discusses the improvements achieved after an external sparger flotation column, 1.42 m diameter by 9.5 m high, was installed as a re-recleaner unit at the Northam Platinum LtdÆs UG 2 plant in South Africa. The paper also evaluates the pilot plant data prior to the industrial size column installation as well as the accuracy of scale up from pilot to full-scale operation. Since the installation of the PrepQuip flotation column, the final concentrate upgrade ratio improved from 83 to 105, the 3PGM+Auå recovery improved from 79.7 per cent to 81 per cent and the Cr2O3 content in the final concentrate decreased from five per cent to 2.8 per cent. The upgrade ratio can be improved to 125 with an overall 3PGM+Au recovery of 80 per cent. Conventional mechanically agitated flotation cells achieved only 74 per cent recovery at an upgrade ratio of 125.

Jan 1, 2005

Tertiary laterite is extensively developed in the Darling Range area, but there is doubt that. the high relief areas along the Darling Scarp have been peneplaned. Three distinct laterite types are distinguished which are termed transported, introduced and residual laterites to avoid ambiguity. Transported laterites are recemented (primarily) lateritic materials and introduced laterites are chemical deposits of bog iron type. Residual laterites are formed in situ from the host material which can be either decomposed bedrock or detrital' clay, and the two varieties formed from these sources are termed residual A and residual B laterites. The genetic requirements for residual laterite formation are (1) host material, (2) porosity and permeability, (3) rainfall, (4) temperature, (5) relief and drainage, (6) vege- tation and (7) time. Previous theories on the origin of laterite appear to be inadequate and incompatible with field observations. Field investigations and drilling in the Darling Range area disclosed lenticular section and thickest laterite development on slopes and thin or oc- casionally no laterite development on crests. Lateritisation is considered a surface feature and the end product of the chemical weathering cycle. The relief and rain-water acting on a kaolinitic host material are con- sidered the major contributing factors in the

Jan 1, 1973

By P Worsey, B Lane

The recommended maximum explosive weight for boulder blasting using internal charges is 0.15 kg/m 3 (Olofsson, 1988). Normally this charge results in excessive scattering and flyrock, creating increased liability for the operator, especially in congested areas. An alternative technique using smaller explosive charges is being developed at the University of Missouri-Rolla (UMR). It is designed to reduce boulder scatter, flyrock and fumes and allows shooting in close proximity, using common blasting products. The method comprises drilling a hole into the top of the boulder, inserting a small primer, filling the hole with water and shooting it. The hole is drilled approximately two thirds into the boulder and the charge (10 g/m 3 ) is placed half way into the hole filled with water. Upon initiation the primer produces a small volume of gas at extremely high pressure which acts upon the surrounding (relatively incompressible) water. The water transmits this pressure to the surrounding blasthole, hydraulically fracturing the rock. As the fractures propagate and the boulder expands a rapid increase in the blasthole volume occurs. Because of the small charge the gas pressure quickly dissipates reducing rock movement, resulting in a fractured boulder with minimal material leaving the immediate vicinity. The current work includes both laboratory and field testing programs. The laboratory program is focussed on determining optimum parameters at reduced scale using concrete cubes. The field program focuses on determining a minimum powder factor and includes shooting smaller boulders up to 1 m 3 underground and 1.5 to 5 m 3 boulders in a surface quarry. In both cases the boulders were obtained as oversize from regular production blasts.

Jan 1, 1999

By A van As

This paper serves to outline the circumstances and causes of the air-blast that occurred at Northparkes Mines in November 1999. It describes the design of the mine, the geotechnical issues surrounding cave propagation and the cave monitoring systems that were in place prior to the event. A short description of the air-blast that followed a sudden collapse is given. Details of the risk assessment process that evolved during the rectification process are provided with their subsequent modification to form the core of a major hazard monitoring process. The system is in line with the recommendations given by the Coroner resulting from the inquest into the deaths of the four people who lost their lives during the air-blast.

Jan 1, 2005

This paper describes operational experience with seam gas and spontaneous combustion management, gained during ten years of production history (1993 to 2003) in the Wynn seam at Dartbrook Coal mine. In addition, comparisons are made with more recent operational experience in the overlying Kayuga seam. Development and retreat longwall operations were undertaken in a 4.0 m thick working section of the Wynn seam, contained within the lower quarter of a circa 24 m thick mega seam, from 1993 until mining operations were relocated to the overlying Kayuga seam in 2004. Production from the first block of the Kayuga seam is currently underway with seam gas and spontaneous combustion management requirements being refined as further operational experience is gained. Seam gas management techniques, including pre-drainage with pressurised fracturing, surface to underground goaf drainage of a carbon dioxide rich seam gas and novel, high capacity ventilation circuits, were employed in the Wynn seam. Ventilation strategies included operating up to carbon dioxide STEL concentrations of 3.0 per cent in segregated return airways rather than being limited to the TWA-TLV concentration of 1.25 per cent. The spontaneous combustion experience at Dartbrook Coal has, to some degree, resulted in a change in the way the risk is managed in Australian coal mines. Values of carbon monoxide make and hydrogen concentrations are profoundly different from previously recommended management plan trigger levels and those used elsewhere in the industry. However, the detection of higher hydrocarbons together with rising oxygen depletion ratios and absolute hydrogen concentrations remain as indicators of advancing spontaneous combustion events. In this respect, experience gained in the Wynn seam was important in the initial management of the shallower Kayuga seam, an essentially greenfield site with no prior operational experience being available.

Jan 1, 2005

By D Trembath

"One of the key risks to the success of a mining operation is the accuracy of the estimates of both the economic mineral and any accompanying contaminants contained within the ore reserve. Misrepresenting the mineralogical characteristics of the ore reserve can result in considerable financial investment in an operation that is in fact uneconomic and/or carries a significant environmental risk. This in turn can result in an unplanned closure of the operation with associated financial, environmental and social legacy. One way to minimise this risk is to undertake high density resource sampling to gain a better understanding of the resource characteristics. However, such an approach is expensive, time-consuming and often impractical. The risk of not having an accurate model is typically assessed during a feasibility study utilising a Monte Carlo simulation method or some form of sensitivity analysis. Importantly, the error margins used in these types of analyses are often based on subjective or very general criteria such as ‘professional judgement’ or an ‘industry standard’. This presentation introduces a conditional simulation method for developing a range of mineralogical distribution models. Based broadly on the method outlined in Journel and Kyriakidis (2004) the proposed approach develops this work further. It combines a geostatistical analysis of the available data with automated mine design software to provide a rigorous method for assessing the confidence in the mineralogical characterisation of the ore reserve. The process is based on simulating possible mine plans based on the statistical characteristics of the available resource sample data. These plans are then assessed against high resolution resource models generated using a Sequential Gaussian Simulation method. The outcome is confidence intervals for important characteristics of the ore reserve estimate relative to the actual resource. These confidence intervals are an objective and transparent measure important for assessing closure risks and represent an improvement over common practice.CITATION:Trembath, D, 2016. A simulation approach for improving the assessment of closure risks, in Proceedings Life-of-Mine 2016 Conference , pp 36–38 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By J Lainé, M Badawi, A C. de Araujo, Y Foucaud, C Veloso

Flotation is the one of the most used techniques for the mineral separation of non-ferrous ores worldwide. However, the increase of the complexness along with the decrease of ores liberation sizes ought to become important challenges for mineral processing, including flotation. It now appears necessary to better understand the fundamentals of the flotation process, particularly the adsorption of flotation reagents at the liquid/mineral interfaces, to propose further improvements. Flotation relies on different phenomena: surfactants adsorption, on one hand, and collision, adhesion, and transport of particles with bubbles, on the other hand. For acknowledging the reagents adsorption mechanisms, molecular modelling tools borrowed from chemical and material sciences, are increasingly used. Atomistic simulations were successfully applied to study the flotation reagents interaction with various mineral surfaces, eg of two common minerals from iron ores, kaolinite, and magnetite surfaces, or with fluorite surface, a tungsten ores common gangue mineral.

Aug 24, 2022

By Restarick C, Jowett A

A cylinder-cyclone system, fitted with a flow control valve between the cylinder and cyclone plus in some tests a variable cyclone spigot, has been used to achieve classifier separations at unusually coarse sizes relative to the diameter of the units used. The method has proved to be useful for low tonnage flows at low pulp density and variable feed rate. The system relies on use of a cylinder unit to reject excess water and fine particles, the amount rejected being adjusted by the flow control valve. The valve also adjusts flow rate and pulp density of feed to the cyclone unit, and can be adjusted to give a separation at a coarse particle size. The system has been used in connection with experiments on the pilot plant at Mount Isa, where a 76 mm system was used to classify feed to the lead secondary rougher circuit at sizes as coarse as 52 micrametres galena equivalent for split conditioning tests. Further tests have been carried out with quartz to assess the range of size separations Possible.

Jan 1, 1978

By M D. Melville, B C. T Macdonald, T D. W

The surface waters in regions with acid sulfate soils (ASS) can contain high concentrations of acidity and dissolved metals. These soils cause problems for agriculture, construction and development. The water can be neutralised through many techniques, however a technique that is low in maintenance and low in cost is most desirable. Due to the vast spread of ASS along AustraliaÆs coastline an expensive and high maintenance solution would not be cost-effective. In this study, a passive treatment system that has been used to neutralise acid rock drainage has been applied to treat ASS water. This system is commonly referred to as an oxic limestone drain (OLD) or an anoxic limestone drain (ALD) depending on the waters dissolved oxygen concentration. The system that has been developed for ASS has a similar closed system to the OLD or ALD, that traps the carbon dioxide which forms when limestone reacts with acidic water. It has been called a closed tank reactor (CTR) and is constructed by placing limestone into an airtight tank. A common problem that will occur when acidic water with a high concentration of dissolved metals reacts with limestone is the formation of metal oxy-hydroxide precipitates. These precipitates can coat or armour the limestone and reduce its reactivity. To minimise the accumulation of precipitates in the CTR, perforated subdrains have been installed. It is anticipated that high water pressure and flow through the subdrains will remove some precipitates. A sump has also been installed at the base of the tank to collect precipitates that settle under gravity. The CTR has been tested for 70 days at a sugar cane farm located at McLeods Creek, NSW. Within this time the sump and subdrains have been used to flush the system. An orange solution was produced during flushing and it is believed to contain iron and aluminium precipitates. The initial performance of the CTR raised pH by at least one unit. Almost all dissolved aluminium was removed and more than half the dissolved iron. The total titratable acidity ranged from 17 - 92 mg/L CaCO3 in the initial month of monitoring. After passing through the CTR the acidity was reduced to zero. The performance of the CTR during the last few days of monitoring decreased. This is believed to be due to a pulse of water with higher acidity and dissolved metal content that lasted a week. In this pulse, the acidity reached 307 mg/L CaCO3 and the total dissolved aluminium reached a maximum of 24 mg/L. Higher concentrations of dissolved metals may have been the cause for lower performance due to increased precipitation and coating on the limestone.

Jan 1, 2003

By G J. Keyter, P J. Terbrugge, Yu Xianb

There has been disappointingly little development in the understanding of the behaviour of rock slopes in open pit mines over the past 30 years. The lack of development in general, and of robust, standardised approaches in particular, are surprising in view of the æultraÆ deep open pit mines that are being developed to depths in excess of 1000 m. Research has recently been carried out into the occurrence of zones of extension strain in open pit slopes. This showed that very large zones of extension strain can occur, and this finding represents a significant new aspect in slope stability that has not been considered before. The greatest magnitudes of extension strain occur near the toe of the slope, either in the slope itself, or in the floor of the pit. Results of the research will be presented for different slope heights, slope angles and horizontal to vertical in situ stress ratios. The magnitudes of the strains are considered to be large enough to result in fracturing of intact rock, and the fracture orientations predicted are adverse for slope stability. Fracturing that is extension in nature is common in competent, brittle rocks and often develops with some violence and little or no warning, producing easily measurable seismicity. In the slope situation, the expected physical manifestation of this behaviour would be popping off of rock slabs and plates of rock from slope surfaces and popping up of the pit floor, as well as the formation of new fractures within the rock mass. Such behaviour may cause overall slope failure, or may initiate failure, which may then be driven to overall slope failure by other influencing factors or combinations of factors. In addition to instability resulting from the fracture surfaces themselves, all induced fracture surfaces could interact with natural geological structures to facilitate formation of a significant failure surface. Case studies of slope failure in two open pits will be described. In both cases failure occurred æsuddenlyÆ after very limited amounts of deformation. In the first, the slope crest moved suddenly upwards and backwards over a length of more than 200 m, with associated instability. In the second, the horizontal displacement of the slope face was almost an order of magnitude greater than the vertical displacement and occurred æsuddenlyÆ. A recently installed seismic system is detecting events in a significant zone behind the slope face. Both pits were in the 200 m to 300 m depth range at the time of the occurrences.

Jan 1, 2003

The Melanesian Outer Arc, extending from. Papua New Guinea to Fiji, developed as a result of interaction between the Australian and Pacific plates throughout the Tertiary, and the following stages are recognized. ,a, Formation of island arc tholeites above a west facing subduction zone in the Lower Tertiary. fit Emplacement of mainly calcalkaline volcanics above an east facing subduction zone in the Upper Miocene and Pliocene. ontinued east facing subduction coupled with fragmentation of the arc from the Pliocene onward. Alkaline and Mg-rich volcanism occurred in addition to continued calcalkaline activity. Tre Upper Miocene and younger volcanism is into five arc segments on the basis of geographic position and nature of the magmatism. The calcalkaline Bismarck arc extending along northern New Britain and including small islands to the west. The alkaline Tabar to Feni arc, north of New Ireland. The Solomons arc, including Bougainville and the western part of the Solomon slands. Volcanism is largely _.alcalkaline, but Mg-rich varieties occur the Solomon Islands. roe New Hebrides arc, extending from the -astern Outer Islands of the Solomons through Vanuatu. Both calcalkaline and :alkaline volcanics are representeo. alkaline and calcalkaline Fiji arc.

Jan 1, 1987

The Mt Muro gold and silver deposit in Central Kalimantan has been in production since December 1994. The geology is characterised by narrow high-grade lodes containing gold and significant amounts of silver. From a largely untrained workforce in the grade control department, production per crew and per geologist has tripled during the three years of production. Grade control drilling evolved from blast hole sampling to reverse circulation sampling. National geologists are trained in basic modeling procedures. A fully integrated reporting and reconciliation system was programed and implemented.

Jan 1, 1997

By Mostyn G. R

An important problem in rock engineering is to control the properties of artificial rock. A compaction technique for casting artificial rock specimens with controlled properties is described, i.e. using a compression-testing machine to compress the mixture. Uniform density is necessary to achieve uniformity of properties of the specimens, and uniform density can be obtained by using the specific pressing method presented. Rebound and borax content are important to the technique and have been studied as well.

Jan 1, 1992

New Zealand contract mining has been well established for close to 50 years. The opencast industry has grown from mining quantities of less than 1 million bcm per year in the 1950s to around 20 million bcm in the late 1990s. Trends here are following those in other countries with mining companies looking to contract out more of the so called traditional mining work. The key driver behind this trend is not unique to the mining industry, but is simply a matter of concentrating on doing a few things well. In the case of the mining company this has come to mean owning and developing orebodies and where appropriate, marketing mining products, and leaving owning and operating of mining fleets to the contractor. This has the effect of reducing risk to the mining company as well as lowering costs. Both can be achieved without losing control of the key elements of the operation. Optimising performance is simply a matter of identifying the key drivers behind performance, having the right plant and the right people at the right place and providing these people with the information they need to manage the operation.

Jan 1, 1997

By Alexander RB, Hollis AJ

The magnitude of the payloads carried by mine haul trucks can have a strong influence on the mine production rates and costs. Consequently control of truck payloads is highly desirable, but in many mines the unavailability of means for measuring payloads reliably, accurately and easily has resulted in a low level of control over truck payloads. Consideration is given to two techniques which are applicable to the measurement of payloads carried by mine haul trucks, namely truck weighing and direct measurement of payloads with truck based systems. Accuracy assessments for two types of truck weighing platforms and two prototype truck based direct payload measurement systems are provided. Results show that weighing platforms based on hydraulic components have proved inadequate, while strain gauge type weighing platforms can estimate payloads to within 2% of true payload when installed, maintained and used correctly. The assessment of the two prototype truck based direct payload measurement systems shows that a high proportion of payloads were estimated to within 5% of the payloads derived from accurate weighing platforms and that these systems appear to have the potential to provide convenient and accurate measurement of payloads. This should enable payloads to be much better controlled than has been possible to date. Predictions of the effect of payloads on production rates and some components of truck haulage costs are possible and some typical results are presented. Accurate prediction of the effect of payloads are not yet possible for some major components of truck haulage costs.

Jan 1, 1986

By M Tayebi-Khorami

There is an increasing trend in the extraction and development of copper resources from complex deposits. The complex deposits pose mineral processing challenges, as they often contain low grade copper ore, relatively large quantity of clay minerals, complex texture, very fine disseminated ore, high amount of pyrite, and high level of impurity elements such as arsenic. With the amount of arsenic in concentrates increasing and with environment, occupational health and safety regulations becoming more restrict, there is a need for a processing method that results in no arsenic emissions and captures all arsenic while immobilizing it in a compound that is stable under a wide range of conditions, so it is suitable for long-term disposal. Some development work has been undertaken to examine the most effective arsenic treatment option for complex orebodies that contain arsenic, but a technically robust and economically viable option has not yet been developed. Previous research has demonstrated the possibility of separating arsenic-copper sulphides from other copper minerals by controlling the potential of the flotation pulp in the single mineral systems. The selective flotation of enargite from copper sulphides in a real complex ore system was studied by Tayebi-Khorami (2016), which is summarised in this paper. CITATION: Tayebi-Khorami, M, 2018. Arsenic in complex orebodies, in Proceedings Complex Orebodies Conference 2018, pp 132–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018