Search Documents

By E J. Coyle, L A. Millington

Tailings storage facilities are geotechnically complicated structures that develop heterogeneous strength profiles and varied porewater conditions. The monitoring of porewater pressures is one of the only direct measurements that can be performed to monitor the performance of a facility throughout its life and is of particular importance in upstream facilities. Foundation underdrainage, continuous and staged tailings deposition, climate inputs (rain, snow, humidity, evaporation, etc), and stratified tailings permeabilities can complicate this critical measurement that introduces uncertainty to stability analyses. These difficult conditions manifest in vibrating wire piezometer measurements as very low or negative pressure readings, both of which are within the instrument’s range of accuracy. However, the data can be difficult to interpret, and a range of interpretations are adopted from optimistic low phreatic surfaces to conservative fully saturated tailings. Where tailings are potentially liquefiable, these very low readings introduce further uncertainty regarding the pore space saturation ratio and liquefaction potential above the estimated phreatic surface. This area of uncertainty is the vadose zone, and its affect on tailings behaviour is not well understood. The two facilities analysed in this paper are upstream, raised embankments with tailings classified as clayey, sandy silt that have been found to be potentially liquefiable. The vibrating wire piezometers (VWP) at both sites show very low or negative readings when they are initially installed near the surface and then go through cycles of re-saturation and de-saturation. Eventually the readings settle as the VWPs are buried deeper within the tailings. The instrumented sections within the tailings column do not show consistent readings that would be indicative of a hydrostatic phreatic surface at either site. Rather, they are highly variable and can be interpreted as either representing a high phreatic surface within the tailings or as a ‘perched’ phreatic zone within the tailings layers. How the VWP data is interpreted has a significant impact on how the facilities are raised and operated. The design outcome for Site 1, which adopts a lower phreatic surface, results in an embankment that meets factor of safety (FoS) requirements under residual strength conditions without any buttressing. Conversely, a conservative (high) phreatic surface has been adopted for Site 2 and has resulted in the facility requiring a significant buttress to meet FoS under residual strength conditions.

Jul 1, 2021

By N Clarke, J Hunt, A Barros, N Guerrero, L Keeney

Grade Engineering® (GE) involves a range of integrated technologies and operating protocols for improving effective feed grade through early rejection of low value material prior to costly processing activities and has the potential to transform the economics of large, low grade, mining operations. Extensive GE test work by AngloGold Ashanti (AGA) and the Cooperative Resource Centre for Optimising Resource Extraction (CRCORE) determined that the Gramalote gold deposit in Colombia is highly amenable to implementation of grade-by-size screening to upgrade the ore at a production scale. To understand the relationships between geology and the upgrade response drill core and bulk samples were analysed at the Centre for Ore Deposit and Earth Sciences (CODES) as part of a larger CRCORE project to understand geological controls on grade-by-size deportment, i.e., the tendency for specific mineral phases to preferentially fractionate during breakage into different size fractions. This work is focussed on understanding the role of mineralogy and texture in influencing rock breakage and natural fractionation at a range of scales. Detailed logging of Gramalote drill core and mineralogical analyses including hyperspectral logging, portable and bench-scale X-ray fluorescence (XRF), plus low resolution Laser Ablation of intact drill core pieces, combined with data from site (drill logs, geochemistry, petrophysics) were used to evaluate the ore and alteration mineralogy, vein paragenesis and textural variability. This provided information on gold deportment and allowed the identification of favourable host veins. Bulk sample material from different ore grade zones was also analysed. A comparison with the results of GE testing shows that positive upgrade results are produced by rocks with abundant veins, particularly those associated with potassic and/or white mica alteration. This work indicates upgrade response can be predicted from drill core using data collected by a combination of automated systems including hyperspectral data, XRF, and detailed drill core logging.

Nov 10, 2020

By R Dimitrakopoulos, K Kawahata, L Montiel

A method that optimises mining complexes that are comprised of multiple processing destinations, open pits and underground operations is presented. Mining, blending, processing and transportation decision variables are simultaneously optimised while accounting for geological uncertainty. The method uses a simulated annealing algorithm at different decision levels to generate a stochastic-based extraction sequence and processing policies. A case study shows its ability to generate a higher net present value while facing a reduced amount of risk when compared to traditional optimisation methods.CITATION:Montiel, L, Dimitrakopoulos, R and Kawahata, K, 2014. Globally optimising open pit and underground mining operations under geological uncertainty, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 201–212 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

BHP Billiton Olympic Dam produces copper cathode, uranium oxide concentrate and refined gold and silver. The operation is comprised of an underground Mine and Processing Plant and is located 560 km north of Adelaide. Water for the operation is sourced from two wellfields located 120 and 200 km from the operation in the Great Artesian Basin (GAB) at a rate of approximately 36 ML/d. Regulatory drawdown limits were established to protect regional GAB springs and are monitored at compliance bores. Drawdown was predicted in the æOlympic Dam Environmental Impact StudyÆ (Kinhill, 1997); however, pumping at higher volumes may have the potential for increased drawdown resulting in a trend towards the compliance limits. In recent years increased usage of water in the Concentrator and Hydromet sections of the Processing Plant has caused excess process water reporting to the Tailings Retention System (TRS). This has resulted in excessive amounts of liquor ponding on the tailings cells with a potential impact being contamination due to seepage of liquor to groundwater. Effective management of water by the operation is necessary to both reduce GAB drawdown and reduce the amount of liquor on the tailings cells. A site working-group has been established to investigate and pursue opportunities to improve the water use efficiency of the operation. This paper will highlight the issue of water management at Olympic Dam and discuss the various options currently being investigated to improve management of this important resource.

Jan 1, 2006

By V A. Chanturia, T N. Matveeva, V V. Getman, A Yu Karkeshkina

The development and application of new effective environmentally friendly reagents for the flotation of thin and ultrathin mineral components is an urgent task. The analysis of the nomenclature of chemicals, including flotation reagents and flocculants, showed that water-soluble polymers (WSP) might be used in flotation separation of fine grinding products containing non-ferrous and precious metals. Water-soluble polymers that are responsive to temperature changes are the most attractive as reagents during flotation. These are the thermo-responsive polymers or thermomorphic polymers. The presence of nitrogen and oxygen atoms in the polymer molecule contributes to the formation of a coordination bond with non-ferrous and precious metals. A research conducted at the ICEMR RAS within the framework of the scientific school of Academician of the Russian Academy of Sciences Chanturia helped to develop a method of flotation of finely ground mineral particles containing valuable components using modified thermomorphic polymers. The paper focuses on the experimental study of poly (vinyl caprolactam) (PVC) as a flotation reagent for gold recovery from finely ground mineral products. PVC is a ready-made water-soluble thermosensitive polymer that does not require complex synthesis. PVC has a high ability to form complexes in an aqueous environment when heated. According to experimental data, the polymer interacts with gold nanoparticles, contributing to the extraction of gold from fine mineral products and the tailings that makes it perspective as an additional flotation agent for the processing of gold-containing ores.

Aug 24, 2022

By L Dubron

This study details a mineralogical and textural characterisation of West African iron ores with an emphasis on their behaviour during mineral processing. By means of both qualitative and quantitative characterisation, a simulation of the beneficiation process applied to these iron ores is performed. A series of different analytical tools are used, including:X-Ray Diffraction (XRD) for qualitative mineralogical analysis;• qualitative optical microscopy (phase identifi cation, description of micro-textures) and (semi)• quantitative optical microscopy (counting of particles, phases and textural types); and• chemical analysis.All the information provided by these analytical methods are combined into a quantitative mineralogical and textural analysis, here called ‘modal analysis’, which enables us to simulate the capability of West African iron ores to be benefi ciated by magnetic and gravimetric separation techniques.On one hand, both qualitative XRD and optical microscopy have revealed the presence of the following mineralogical phases: magnetite, haematite, goethite and quartz. On the other hand, the chemical analyses provide us with quantitative inputs expressed as oxides. We have converted the oxides into mineralogical contents expressed as magnetite, haematite, goethite and quartz. In this way, we build a simple quantitative mineralogical analysis.Beside this, the semi-quantitative approach of the characterisation by optical microscopy also provides us with a liberation study, enabling us to split the gangue-bearing content between two types of particles:1. liberated gangue-bearing particles, and2. composite particles composed by both iron (oxhydr) oxides and gangue-bearing minerals.We have assumed that we could anticipate the behaviour of these two kinds of particles through a mineral process, by simulating the removal of at least the liberated particles of gangue. Optical microscopy also revealed a trend in the weathering profi le of the Tokadeh ore horizon with a decrease from bottom to top of magnetite and an increase of both goethite and martite showing a higher level of oxidation and hydration in the upper ore horizon.We have applied this removal extent upon the quartz content of the mineralogical quantitative analysis and we have re-calculated the quantitative mineralogical analysis considering the expected decrease in the quartz content. Finally, by converting the re-calculated (oxhydr) oxides contents into iron grades and summing them, we do obtain a fi nal simulated iron grade for the upgraded products.

Jul 11, 2011

By M Revell, B Sainsbury, D Sainsbury

This paper extends the existing knowledge associated with the design and placement of prefabricated pastefill barricades through a consideration of asymmetric drive geometry and conditions. The load capacity of prefabricated barricades and their failure modes are considered in relation to abutment geology and barricade geometry that includes curvature and span and drive geometry that includes abutment angles, haunch angles and misalignment. Design charts are provided for typical barricade sizes to provide general guidance for design capacities and optimising location placement based on asymmetric drive geometry. A recent barricade failure is considered in relation to the drive geometry and the potential impact it had on the installed capacity.

Nov 29, 2022

By H A. Linn, K Winn, C W. Lee

The Q-slope method for rock slope engineering was developed to enable engineering geologists and rock engineers to rapidly assess the stability of excavated rock slopes in the field and make optimal adjustments to slope angles as rock mass conditions become apparent during construction of road cuts or benches. An empirical relationship between Q-slope and long-term stable slope angle is now supported through over 500 cases studies from Asia, Australia, the Americas and Europe. This paper presents about the stability analysis by first-ever applying Q-slope method on abandoned quarry wall in Singapore. The 30 m high rock slope which is composed of monzogranite rock was severely damaged by blasting operation. As the rock slope is intended for public view the objective was to retain the natural outlook and without any artificial support application thus manual scaling was carried out to clear the loosed rock blocks. In the end stable slope angle of clean rock face is determined once again by Q-slope method.

Nov 29, 2022

By D C. Ford

The Argyle AK1 orebody was discovered in 1979 and subsequently found to be a large, economically viable reserve with high grade diamondiferous ore. Production began via an open pit operation at the end of 1985 and has continued for some 25 years to present day. This, however, will come to an end in the next few years with production moving to an underground operation via block-cave mining methods.A series of studies from 2001 - 2005 was carried out; diamond drilling commenced after approval in 2006, from an exploration drive to determine the likelihood of the current proposed block cave operation.In 2006, development of the block cave project began, in order to realise the part of the orebody below the extent of the open pit mining operation.Development of the block cave technique, comprising an undercut level beneath the target zone of the orebody with subsequent extraction level 15 - 20 m beneath, relies largely on a number of block-caving parameters (hydraulic radius, rock type, structure and orientation of stress and grade of the orebody). These all have an influence on cave ability and eventual profit of the operation. Evaluation of further potential for taking this orebody beyond the block cave phase with options such as sublevel-caving are being considered for the UG-2 portion of the resource/reserve. Diamond drilling for this work is currently under revise.The challenges faced in transitioning form the surface operations to the underground, comprising a changing workforce, converging development drives, underground aquifers, major excavations and transportation of ore via automation are intriguing.

Aug 22, 2011

By Hartley JS, Wills KJA

The Thalanga massive sulphide deposit is hosted by Upper Cambrian rhyolites and volcaniclastics of the Mt. Windsor Volcanics near their contact with overlying dacites, rhyolites and sediments of the Trooper Creek Formation. The ores and host rocks have been subjected to a single strong deformation and to lower to middle greenschist facies metamorphism. A main lens with surface gossan dimensions of 55U m x 6 m dips steeply, plunges shallowly to the west and is offset by a series of normal faults. It is flanked by smaller lenses to the east where the mineralized horizon is stopea out by granite. The area to the east and south of the gossan is masked by Tertiary cover. A complex exhalite package is represented by banded sphalerite-pyrite- galena-chalcopyrite, massive pyrite and chalcopyrite and assemblages dominated by dolomite, chlorite-actinolite, tremolite, talc, barite and rare gypsum. Accessory tetrahedrite, arsenopyrite, bismuthinite, magnetite and native gold are associated locally. Pods of quartz-magnetite formed distally. The ores are underlain by strongly to moderately pyrite-silica-sericite altered rhyolites with the strongest alteration closest to an interred synvolcanic fault. This alteration is characterised by an enrichment in MgO, Na2O, FeS2 and base metals with a depletion in CaO and Na2O. There is a general enrichment in Pb and Zn towards the hanging wall with some enrichment of Cu near the base of the main lens due to replacement by ore tiuias near vent discharge sites. Zonation of Cu to 2n-Pb in also evident over narrow intervals

Jan 1, 1987

By M Watkinson

Tube bundle monitoring systems have come a long way from their first introduction to coal mining in the late 1960s/1970s. Early developments in the United Kingdom (UK) commenced with single gas analysers (carbon monoxide) and quickly moved towards introducing oxygen analysers and methane analysers for improved analysis, in particular the calculation of air-free results. Recommendations were made in the early days as to how and where to run tubes and on the matching of sample pump and purge pump pressures. Current Australian installations are commonly based on a four-gas multianalyser, infrared for carbon monoxide, carbon dioxide and methane, and paramagnetic for oxygen. These systems are controlled with programmable logic controllers (PLC), with component monitoring as an integral part of the software. This paper discusses the development of tube bundle systems from the 1960s to the current date and looks at the advantages and disadvantages of the installations, along with making operational recommendations to be considered with the siting of the analyser building, running of tubes and maintenance of the system.CITATION:Watkinson, M, 2015. Developments in tube bundle gas monitoring, in Proceedings The Australian Mine Ventilation Conference, pp 259–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By M Tsai

Tube bundle gas monitoring systems have been used in the mining industry for over 50 years. The initial design was based on four individual gas analysers along with a series of solenoid valves, gas sample conditioning and flow control mechanisms to ensure the correct gas flow stream volume to the analyser. Simtars staff have identified flow control issues when providing operational support to coalmines on numerous occasions. The accuracy of the oxygen analysis is dependent on control of the gas flow to the analyser. Oxygen is one of the parameters used in calculating Graham’s ratio which is used for the detection of spontaneous combustion activity in coalmines. This paper will provide data which identifies the flow control issues by comparing mine site records for the two surface sample lines in the analyser room and the gas cage. Mine sites will be deidentified within the paper. The paper will discuss some of the changes that have been made in modern tube bundle systems and compare the change to the initial design specification developed by the UK National Coal Board, investigate possible operational impacts and provide a technical fix to solve the current flow issues being experienced at some mines.

Oct 12, 2022

By J T. Smit

The theory of froth flotation developed slowly, in almost all cases lagging behind practical developments in the operation of flotation processes. This was largely the result of a lack of understanding of the required basic principles of chemistry and physics, many of which were being developed at the same time. A review of some of the early theories propounded is worthwhile, and should encourage those who are presently studying or practicing flotation to exercise some care in claiming a complete understanding of the underlying phenomena in the art. This paper considers theories presented up to and including those in Principles of Mineral Dressing by Antoine M Gaudin (1939). Of course, developments since that time are important, but they are beyond the scope of this discussion.

Jan 1, 2005

By C A. Foss, D A. Clark, D Hillan

While magnetic surveys are the most common geophysical method used in mineral exploration, magnetics and geology remain to be fully integrated quantitatively in iron ore provinces. Although high-resolution aeromagnetic data has been collected over prospective areas of the Hamersley Province, much of the information in the data sets has hitherto not been fully exploited due to a lack of suitable interpretation methods. Recent advances in the processing and modelling of magnetics in highly magnetic terrains, constrained inversion and 3D visualisation and understanding the magnetic properties of banded iron formations and iron ores potentially create the capability to generate realistic 3D mapping of magnetite and hematite concentrations over large areas. Initial processing of conventional total magnetic intensity data produces true potential field maps that are unaffected by local perturbations of the regional geomagnetic field direction by intense local anomalies. The true potential field can be converted into vector and tensor components, each of which emphasises different structural features of the geology. Scalar quantities derived from these components simplify interpretation, using new methods, developed by CSIRO and elsewhere, that are less sensitive to magnetisation direction. Preliminary interpretations allow interpolation between mapped units and structures and evaluation of remanence and anisotropy effects. Accurate modelling requires rigourous treatment of self-demagnetisation and magnetic interaction effects. Semi-automated constrained inversion, combining magnetics with available geological information and other geophysical data, can be utilised to generate models of disposition of major magnetic units and the 3D magnetisation distribution within them. The final stage of interpretation is to exploit the understanding of magnetic properties (susceptibility, anisotropy and remanence) developed over many studies by CSIRO, the University of Western Australia and others to convert the interpreted magnetisation distributions into 3D maps of magnetite and hematite contents, which are the quantities of direct exploration interest.CITATION:Clark, D A, Foss, C A, Austin, J and Hillan, D, 2015. Three-dimensional mapping of magnetite and hematite concentrations from reprocessing of detailed aeromagnetic data, in Proceedings Iron Ore 2015, pp 229–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J Greberg

This paper discusses the use of simulation in the mine planning process. A case study on the Newcrest Cadia East project is presented, and the challenges and possibilities for using simulation as a tool for mine planning and scheduling is discussed.The simulation study presented in this paper was performed during the project’s prefeasibility stage, and focused on the planning and scheduling of the development of panels in the future mine. The Cadia East project will be the largest underground operation in Australia and the first using panel caving. Simulation was used in order to optimise the development of panels; it was mainly used in order to verify the plans for the development process and allocate resources in an optimal way. The work was performed as an iterative process and adjustments to the plans were made according to simulation results. Bottlenecks were identified and different scenarios were tested.The results from the simulation study shows how different operational constraints affect the planned development process and how changes in priorities can be necessary in order to maintain a high development speed. Furthermore the study shows how changes in planned mine layout requires changed strategies, and how this was solved using the simulation tool.In this paper the authors critically discusses the use of simulation in mining operations: what are the limitations and challenges of using simulation as a tool for mine planning and scheduling, what are the benefits, and what do we aim for in the future?

Nov 22, 2011

By Daoust G, Dubois JF

The optimal sequence of decisions on rates of production and cutoff grades is obtained by a dynamic programming model. The main parameters are : 1. the size of the deposit, average grades and grade distributions, 2. the operating costs of mining and concentration, 3. the investments in mine and mill, 4. the smelter charge, 5. the price(s) of the metal, 6. the recovery and the grade of the concentrate, 7. the rate of interest, 8. the taxation formulae, 9. the upper limit to rate and the rate interval and 10. the upper and lower limits to cutoff and the cutoff interval. An amount of ore can be mined at various rates while applying various cutoff grades. It is assumed that a decision to mine at a certain rate during a period conducts to a certain state regardless of the cutoff grade. This assumption which is valid for several

Jan 1, 1977

Exploration by Cyprus Minerals Australia Company (formerly Amoco Minerals) has successfully outlined significant Au-(Cu) mineralisation at Starra, 150 kilometres south-east of Mt. Isa. Mineralisation is stratabound and localized in deformed and metamorphosed ironstones (B.I.F?) and iron-oxide bearing schists of the mid-Proterozoic Staveley Formation. Over 90% of the presently outlined potential ore occurs in 4 discrete zones within a strike length of 3.5 kilometres. The inferred geological resource in these zones is approximately 6 million tonnes grading 5 grams per tonne gold and 2% copper. Roughly half of this is open-pittable, but more rigidly applied mining criteria will probably reduce the exploitable tonnage. Detailed infill drilling is in progress and a pre-feasibility study has commenced. The joint venture partners, Cyprus Minerals (75%) and Elders Resources (25%) expect to make a development decision by the end of this year.

Jan 1, 1986

By Heape JM

Production from the Cattle Grid orebody commenced in August, 1974. This followed a recent discovery arising from an extensive exploration programme involving stratigraphic drilling, geochemistry and geophysics. Located some 4 km west of the original copper occurrences at Pernatty Lagoon the discovery was found to contain 4.6 million tonnes of ore averaging 2.4% copper. The ore is a "sandstone copper" type localised near the disconformity between two Precambrian (Adelaidean) stratigraphic units, the Pandurra Formation and the Whyalla Sandstone. The mineralisation roughly follows the interface between these units and occurs in fractures, vugs and along bedding planes. The mineralogical character of the ore is somewhat complex consisting of chalcocite and bornite, with associated chalcopyrite, sphalerite, pyrite and other less common sulphides. 1. Senior Geologist, Pacminex Pty. Limited, Sydney, N.S.W. 2. Mine Geologist, for Mt. Gunson Mines, Pacminex Pty. Limited, Mt. Gunson, S.A.

Jan 1, 1975

Robe River Iron Associates (RRIA or Robe) is widely regarded as the worldÆs most cost-effective, consistent and reliable supplier of iron ore. It has been in operation since 1972 and globally is the fourth largest seaborne trader in iron ore exporting 25.5 million tonnes of -9.5 mm sinter fines and 4.5 million tonnes of pisolite lump (-31.5 +6.3 mm) during 1999. Robe is a joint venture that controls major iron ore resources in the Pilbara region of Western Australia. ItÆs participants are North Limited with an interest of 53 per cent (65 per cent including minority interests) and Japanese companies Mitsui (33 per cent), Nippon Steel Australia (10.5 per cent) and Sumitomo Metal Australia (3.5 per cent). Robe River Mining Co Pty Ltd manages the project which is a subsidiary of North Limited and Mitsui.

Jan 1, 2000

On the 17th November, 1964, a new No., 2 lead blast furnace was blown in at Port Pirie. The furnace departed from previous designs by incorporating a centrally located continuous tapper for both lead bullion and slag. The use of a central tapper permitted a simple and effective layout for the handling of both products. Considerable development was necessary to bring the furnace to its present level of efficiency. Units vital to the continu- ous operation were developed to allow quick replacement, thus ensuring high time efficiency under varied operating and maintenance conditions. The furnace was designed with the following objectives in mind, 1. increased crucible life, 2. elimination of oxygen for slag tapping, 3. higher temperature slag for fuming operations-, 4. less operator skill needed, 5. reduced tapping tool consumption, 6. elimination of settler skull and scrap lead, 7. better control of blast air distributi.nn. And

Jan 1, 1975