Search Documents

By T Craske, J Sykes, T C. McCuaig, M Jessell, A Trench

The prevalent strategic approach in the mining industry is one of planning. However, it is widely recognised that planning does not work in complex and uncertain situations (Mintzberg, 1994), such as those associated with ‘above ground’ non-technical orebody complexity (Trench, Packey and Sykes, 2014). Mintzberg, Ahlstrand and Lampel (2009) suggest the focus instead should be on strategic ‘thinking and doing’ and using the many ways to think about strategy to make sense of complex, uncertain, and unique situations. They therefore place great value in cognitive flexibility. Scenarios development utilizes several different thinking styles and thus assists with this type of flexible strategic thinking (Figure 1). The ‘Centre for Exploration Targeting (CET) Scenarios’ were developed with the ‘Oxford Scenario Planning Approach’ (OSPA) (Ramírez and Wilkinson, 2016). The OSPA aims more to improve the thinking skills of decision makers, rather than forecasting per se (Wack, 1985a, 1985b). As such, this paper focuses less on the content of the scenarios and instead on the practical value of scenarios in strategizing. CITATION: Sykes, J, Trench, A, McCuaig, T C, Jessell, M and Craske, T, 2018. Strategic thinking about long-term ‘above ground’ orebody complexity using scenarios, in Proceedings Complex Orebodies Conference 2018, pp 60–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By M Zanin, E Chan, D Xu

An experimental design has been developed to investigate the relative influence of distinct pulp and environmental properties on froth stability in the flotation of a typical porphyry copper ore. In particular, factors such as frother and collector type, feed particle size (P80), solids per cent, composition (chalcopyrite and pyrite content), as well as grinding environment (mild steel versus stainless steel, high and low pH) have been varied in a controlled manner, and the resulting froth stability evaluated. A previously developed froth stability column, based on the Bikerman approach, was used to measure the froth height and half-life in each test. The relative effect of each factor is presented here on a comparative basis. It is shown that frother type is the most important factor, with marked difference in froth stability when switching from methyl isobutyl carbinol (MIBC) to glycol based frothers. Solids per cent and particle size also play a significant role. The grinding environment had lesser effect on the resulting froth stability, although mild steel grinding gave higher froth stability compared to stainless steel grinding. The experimental evidence supports the hypothesis that in porphyry copper flotation the grinding environment influences surfaces oxidation, pyrite activation and the extent of hydrophobic particles reporting to the froth phase. This has an indirect effect on the resulting froth stability, which is however small if compared to the other factors. This work is still in progress, and extension to other mineral systems is planned. However, some insights are offered to operators on the parameters which are more likely to have an impact on froth stability in copper flotation plants.CITATION:Zanin, M, Chan, E and Xu, D, 2014. Empirical evaluation of factors affecting froth stability in copper flotation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 193–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D Piason

Newstan Mine commenced mining operations in 1887 and has since undertaken extensive mining within the Young Wallsend, Great Northern, Fassifern, Borehole and West Borehole coal seams using a range of mining methods including board and pillar mining and longwall mining.Newstan Mine is planning to extend the existing mine workings using longwall and miniwall mining methods to produce up to 4.5 Mt/a of run-of-mine (ROM) coal for at least 25 years. The planned extension in the Main East and South West sections will involve developing new longwall panels and related mains headings. The new area contains higher specific gas emissions (SGE) than previously experienced at Newstan Mine. To achieve the optimum ventilation requirements for the longwall operation in this new area, a new ventilation shaft was designed to be constructed using the blind boring method in the South West Headings section.This paper presents the shaft design parameters and selection criteria for the construction of the new ventilation shaft, including the construction phase and the holing process to connect the shaft to the underground workings. The paper also discusses future ventilation requirements for Newstan Mine.CITATION:Piason, D, 2015. South-west ventilation shaft project at Newstan Mine, in Proceedings The Australian Mine Ventilation Conference, pp 229–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Chunbao Z, Zhenchuan Z

As known to the international mining sectors, Hunan province, called as ' Nonferrous Native Area ', is the main base of nonferrous metals Pro- duction in China. There are over 194 nonferrous mines in this province, most of them distribute over the basin of Xiangjiang River. The state of management of wastewater in Hunan's nonferrous mines is outlined.The experiences and economic benefit in the management and treatment of wa- stewater in Bofang and Mayang copper mines, and at Shizhuyuan polymeta- llic mine, are mainly introduced. It concludes with measures and recommendations for future management and treatment of wastewater in Hunan's nonferrous mines.

Jan 1, 1988

By Bodnaras G. E, Sceresini P. A

The Filblast Cyanidation Process incorporates the advantages of intense high shear mixing, high dissolved oxygen concentration and high pressure to achieve extremely rapid gold dissolution rates. This is made possible by the unique design of the Filblast gas shear reactor. The reactor is a rugged and compact in-line device. The outer casing is protected by a polyurethane coating and the internal parts are of wear resistant polymer. The largest unit built to-date has overall dimensions of 1200 mm length by 300 mm diameter and has a capacity of 150 dry tonnes per hour at 40 - 45 per cent solids. Service life at this throughput is at least three months. The process may further be applied to high temperature leaching of refractory gold ores or other metals. Wear resistant metal or ceramic materials would be employed for this duty. Four mines are currently employing the Filblast Process for treating a variety of ore types ranging from highly reactive, almost impossible to treat, pyrrhotite/arsenopyrite to deeply weathered clay ore which forms a highly viscous pulp. The effect of shear thinning has resulted in improved adsorption kinetics resulting in higher carbon loading and reduced soluble gold loss. Total tonnage treated is approximately four million. Operating costs which include leasing and maintenance charges for the Filblast and pump power costs are about 16 cents per tonne. This is equivalent to about ten per cent of savings. Laboratory scale units having capacities up to 30 litres/min are available for test work but laboratory testing techniques so far developed do not accurately reflect the oxygen and cyanide savings which have been achieved in the plant.

Jan 1, 1994

By J F. H Thompson

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Mineral exploration and mining are challenging businesses. Remote and at times harsh conditions have always made it difficult for exploration, but modern explorers also have to deal with cover, numerous technologies, an explosion of data and critical early community engagement. Mining deals with the reality of moving and breaking thousands of tonnes of rock each day to extract what can be a very minor component of economic value, and, furthermore, society expects that this will be done in a clean and sustainable manner. The exploration and mining challenges appear disparate, but they are intimately related.Although not widely appreciated, both exploration and mining have a long tradition of innovation. Over the last 50 years, major step changes in exploration have resulted from radical advances in our understanding of ore forming processes, new geophysical, geochemical and remote sensing technologies, and new ways to integrate and interrogate data. Over a more extended period, close to 100 years, mining has developed bulk surface and underground methods, selective extraction through flotation and leaching and global positioning system–geographic information system control systems that collectively facilitate mining at a massive scale. And yet, in spite of these successes and the boom that we have enjoyed in the last ten years, the industry is under pressure and the need for innovation and change is paramount.The major drivers for innovation are the need for increased quality in discoveries and mines and the need to interact effectively with communities and jurisdictions such that the benefits of quality mines are recognised and enjoyed widely.We are still making new discoveries around the Pacific Rim and elsewhere, but many argue that the quality – grade and accessibility – of these discoveries is decreasing. The net result is that explorers are delivering resources and reserves for development at lower grades and with higher capital and operating costs than current operations. For mining, the increasing age of many existing operations contributes to increasing costs, which, when combined with decreasing cut-offs and lower grades, also results in declining quality. The combined picture does not look good.Just as the pressure to improve performance and margins in the face of declining inputs increases, we are simultaneously faced with increasing societal demands for improved environmental performance and sustainable practices. This is most apparent at the local, community level, where opposition ultimately leads to delays or even cancellation of new projects. Quality is again the issue – quality of the initial and ongoing engagement and quality of the proposed mine in terms of environmental and economic performance.CITATION:Thompson, J F H, 2015. Exploration and mining – the need for innovation , in Proceedings PACRIM 2015 Congress, pp 45–48 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By L Eriksson, D Penn, J Appelgren

Atlas Copco, a leading supplier of equipment and services to the mining and construction industries, is consistently pursuing its strategy to offer the most productive and economical solutions by continuously offering new innovative products. These are, in most cases, developed and tested in close cooperation with demanding end users before being officially launched on the international market. The demands for higher productivity and improved overall economy have resulted in systems for automation of the drilling cycle and also tools for integrating the drilling equipment to the production control system used by the customer. In terms of improving the blasted material quality, the company has placed emphasis on accuracy in the drilling process and documenting what has been drilled. By applying state of the art technology to the common automation platform, developed for the surface drilling market, major steps in improving overall drilling productivity and blasting performance have been achieved. This paper will give some examples derived from the latest development of solutions for the companyÆs surface drilling products.CITATION:Appelgren, J, Eriksson, E and Penn, D, 2012. Rotary drilling automation increasing operator productivity and drilling quality, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 13-18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By F C. D Michelin

As mines get deeper, the critical underground temperature limits will be exceeded, and an increasing number of mines will need to implement, expand or modify cooling systems. Surface cooling plants have many advantages over underground cooling such as efficient heat rejection, and lower relative capital cost; however the delivery of cooling through long underground distances can result in lost refrigeration capacity before the chilled air reaches the areas it is needed most. Refrigeration plants are therefore often overdesigned in size and capacity to compensate for underground losses.More mines are now utilising real-time monitoring and automated control of ventilation airflow and fan systems to ensure the conditions underground are safe and productive, and power consumption is efficiently managed. There may be significant opportunities to extend ventilation monitoring and control into the refrigeration delivery and control system.Energy reduction is an effective way to reduce costs and CO2 emissions, which is an increasingly important part of corporate governance. More efficient refrigeration control is a further step toward reducing energy consumption. This paper looks at an added step in how real-time monitoring can assist in controlling the output and chilled air delivery of a cooling plant. The requirements, implementation, benefits and challenges will be discussed.

Oct 12, 2022

By D Connelly

Magnetite ores can be used to produce very high-grade concentrates that are suitable feed for the direct reduction process route but the high sulfur content of some concentrates can cause substantial environmental issues. Processing of high sulfur magnetite ore is therefore increasingly problematic for the industry. Generally, the industry demands a concentrate with <0.05 per cent sulfur and <2 per cent silica. This paper reports the outcomes of a study to produce a concentrate with the requisite low sulfur content from a sulfur-rich magnetite ore. The main findings may be summarised as follows: if the sulfur is present in magnetite as nonmagnetic pyrrhotite or pyrite, it can be beneficiated using magnetic separation and hence, monoclinic pyrrhotite is magnetic and is magnetically recovered with magnetite leading to a concentrate that is too high in sulfur. X-ray diffraction and QEMSCAN analyses revealed that the magnetite concentrate was liberated at P80 30 microns and was associated with maghemite, pyrrhotite (magnetic), carbonates and hematite with very low amounts of chalcopyrite, sphalerite and arsenopyrite. Sulfur removal using flotation was the first stage of investigation and this required flash flotation in the grinding stage followed by column flotation of the initial concentrate to generate the final concentrate. At the same time, it was observed that oxidation of the pyrrhotite had a negative effect on its flotation requiring copper sulfate to activate it. Bioleaching and concentrate leaching were also considered and achieved over 90 per cent sulfur removal but were deemed unsuitable owing to the production of highly reactive wastes and high CAPEX. Reference is made to a number of operating magnetite producers and how they manage the sulfur in feed.

Sep 18, 2023

By Mine F. J, Woods P. H

The Top End of the Northern Territory lies in the monsoonal zone and receives rain during the November-April period. Initially, at the start of the wet season, rain storms are localised, but, following the descent of the monsoonal trough from below the equator, widespread rain occurs. Overflow incidents at mine sites tend to arise midway through the annual wet season when excess water accumulated in ponds begins to discharge to the external environment. Remote-access monitoring may be undertaken at mine sites using equipment to continuously measure water quality parameters with storage of the information on a data logger. The data is then retrieved by visiting the site and transferring it to a portable computer or by remotely accessing the system using a telemetry system and transmission via telephone, VHF/UHF or satellite. Such systems are readily available and vary in cost depending on the sophistication of the data transfer system. Available sensors for continuous monitoring include those for conductivity, temperature, pH and other ion selective electrodes, eg nitrate, and water level. Of these variables, conductivity is most useful due to its inherent accuracy and stability of reading. Remote monitoring capability is able to provide: (i) more intensive monitoring of key issues; (ii) more timely information; (iii) correct perspective on the degree of environmental problem; and (iv) information from remote locations, which would be difficult to monitor by more conventional methods. Examples are given for applications of continuously logged measurement of conductivity of waters discharging to drains and in creeks at Pine Creek, Ranger, Nabarlek and Woodcutters mines in the Northern Territory. These applications demonstrate the timeliness of the continuous monitoring technique.

Jan 1, 1994

By A M. Mueller

St Helena tunnel is the centrepiece of the Pacific Highway upgrade from Tintenbar to Ewingsdale, abbreviated and commonly known as T2E. At the deepest point the twin tunnels run 45 m below the ridge line of St Helena Hill, located about 5 km west of Byron Bay. The tunnel breakthrough was achieved early in 2014 and the works for permanent lining will be completed in early 2015.Once the project will be handed over to the public in 2015, T2E will deliver a safer highway and uninterrupted traffic flow between New South Wales and Queensland. The design speed in the project area has been set to 110 km/h by the client Roads and Maritime Services (RMS), which will reduce the travel times between Brisbane and Ballina to just over two hours.The two tubes of the tunnel have been designed to accommodate three lanes in each direction with shoulders and walkways on either side of the carriageway. These requirements result in a huge cross-section of about 20 m width and an excavated area of about 210 m2.With the tunnel alignment being situated in basaltic rock, St Helena tunnel is conventionally driven. The selected excavation method was predominantly drill-and-blast with temporary support being installed immediately after the excavation. Despite the wide span of the tunnel, the geology allowed the tunnel perimeter to be supported by only rock bolts and a layer of shotcrete over the majority of its length.Due to environmental reasons one of the approval criteria of the project was that the tunnel must not have a detrimental long-term impact on the groundwater system within St Helena Hill. Consequently the tunnel has been designed as a fully tanked structure with a waterproofing sheet membrane installed on the temporary shotcrete.The permanent structure of the tunnel has to meet a 100-year design life and it is designed as a cast in situ concrete lining. Considering the water pressure on the lining the concrete is reinforced with a significant amount of bar reinforcement.The presented paper provides a more detailed explanation of the geology and the consequential temporary and permanent support measures together with the waterproofing system.CITATION:Mueller, A M, 2014. Pacific Highway upgrade from Tintenbar to Ewingsdale (T2E), St Helena Tunnel, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 419–424 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By E J. Hill, F Huang, A Otto

Geochemical data from drill core samples is used in mineral exploration to enable geologists to understand subsurface geology. However, it is challenging to analyse these data sets rigorously and consistently. Manual data interpretation relies on the knowledge and experience of logging geologists. When multiple geologists are involved, it is possible to introduce inconsistencies in logged lithology type and scale of logging (‘splitters’ versus ‘lumpers’). Machine learning (ML) is a powerful tool for analysing high dimensional data (ie data with many variables) and large data sets (ie data with many samples). However, ML methods applied to drill hole samples do not incorporate spatial information and this can result in high misclassification rates and small-scale ‘noisy’ results. We demonstrate the use of multiscale spatial analysis (wavelet tessellation) as a pre-ML step to analyse spatial information. This step helps reduce misclassification and filter out unwanted small-scale variation in the data. In an experiment, we used wavelet tessellation and supervised ML to predict litho-geochemical rock types from geochemistry data. The data set is from the Valhalla uranium deposit near Mount Isa, northern Queensland. First, geochemical knowledge and statistical analysis was used to select appropriate geochemical elements for litho-geochemical classification. Second, the elements were processed using multiscale spatial analysis. Third, we trained a Random Forest model with the data set and found that the model performs worse in predicting rare rock samples than common ones. We applied over-sampling and down-sampling methods in aim to overcome this issue. As a conclusion, the combination of multiscale spatial analysis (to define rock unit boundaries) and Random Forests (to classify rock units) is a good method for rapid and accurate analysis of drill hole geochemistry.

Mar 22, 2022

By P B. Schwann

The commonly accepted genetic theories of Pilbara iron ores and Woodie Woodie manganese ores have often presented them as quite unique. This apparent uniqueness is not confined to just iron and manganese, but is also seen in gold and copper deposits in Western Australia. The published material on iron and manganese ores would seem to have either a quite complicated genesis or none at all. An alternate theory for the origin of these deposits is presented which involves a protore with simple oxidation and pH controls with hydrothermal fluid sources from the diagenesis and dewatering of the underlying strata. This theory explains the distribution, thinning, cold dolerites and very high concentrations of deleterious minerals observed in these deposits. This genesis system is also related to the systems that deposit hydrothermal gold and copper in sediments in the region.This paper presents the author’s observations, sampling and mapping after several decades studying and exploring for the minerals in Australia and locations overseas. All of these theories were developed with (or in spite of!) the guidance of Mal Kneeshaw, but would never have seen the light of day without him and the others presenting here. It is not what I would call scientifically polished, and possibly deserves more detailed studies; it is, however, presented as a discussion paper.CITATION:Schwann, P B, 2015. Related genesis for iron, manganese and gold-copper ores in Western Australia, in Proceedings Iron Ore 2015, pp 327–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A McGann, P J. Coghill, D Miljak

"It is widely accepted that bulk ore sorting could provide a step change in processing of low-grade ores. For this to be achieved a rapid, accurate bulk sensor of grade is required as well as sufficient natural variation of grade in the ore stream. CSIRO trialled a magnetic resonance (MR) sensor capable of measuring chalcopyrite, and by inference total copper grade, on the 1300 t/h Ridgeway portal conveyor. The gauge produced an unprecedented set of data down to a 1 t scale for months at a time. This paper analyses the measured variation and compares it to a simple model derived from the bore core data and mixing within the block cave mine.The model of the small-scale (&lt;1000 t) variation is developed using fractal methods which have successfully been used in the past for copper porphyry deposits showing a power law or near power law distribution of copper grade and vein sizes. These fractal distributions have two features highly favourable for segregating ore, a large proportion of low-grade pods and the large-scale spatial clustering of grade. We show the presence of fractal ordering in bore core data at short range in the Cadia Ridgeway porphyry deposit and measure its persistence in the crushed rock produced by the Ridgeway block cave mine over one month. The model is then extended to demonstrate the effect of varying head grade, mixing and pod (or diversion) weight on bulk sorting efficiency.CITATION:Coghill, P J, Miljak, D, McGann, A, 2016. Modelling Grade Variation in Crushed Ore at Cadia Ridgeway and Its Potential Consequences for Bulk Ore Sorting, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 77–88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Falbo A, Quarestima S, Cozza C, Barbaro M

A new synthetic reagent of the mercaptobenzoxazole class, 5- methyl-2-mercaptobenzoxazole, has been studied. This reagent exhibits powerful selective collecting action towards copper sulphides present in several complex ores, as demonstrated both by laboratory and pilot plant tests. Industrial production is expected to start in the near future. The way this reagent reacts with pure chalcocite has been studied utilising in situ FTIR techniques, adsorption tests, electrokinetic potential measurements and Hallimond cell flotation tests. The FTIR studies have indicated the nature of the surface phase. Adsorption isotherms obtained by the rest method have revealed the quantitative evolution of surface products, permitting the determination of surface coverage at various reagent concentrations. The electrokinetic potential has been utilised to verify the stability of individual species in diverse concentration ranges. Correlation of the results obtained has provided indications on the chemical interaction of this reagent with the surface and on the surface Arrangement.

Jan 1, 1993

The paper continues an account, begun in a previous paper, of experimental work carried out by the author whilst a member of the metallurgical staff at the Cockle Creek Works. The general method of the description of the plant and works practice adopted previously has been followed.The paper is a short account of the methods used in and the results of an investigation of the fume losses from the various parts of the plant.MEASUREMENT OF VOLUMETwo independent methods were used. The first depended on a number of pitot-tube measurements of velocity. These readings were taken in the stacks leading from the various furnaces at a considerable height above the ground so as to obtain as regular conditions as possible at the points where the readings were taken.Three openings were made in each stack and the pitot tube inserted into each opening in turn and readings taken at the centres of imaginary areas of equal size. The average velocity in the stack was thus obtained.After four tests had been made at the smelter stack, which removed the gases from all blast furnaces in use, the centre of velocity of the gases for each test was calculated and was found to be practically constant in position. The previous procedure was varied in subsequent tests on this stack by taking a succession of readings at the centre of velocity instead of at various points...

Jan 1, 1925

Longwall mining operations have been in place in Australia since the early 1960s. This mining method is currently used to extract the bulk of coal obtained from underground mines in Australia (CSIRO, 2010). Despite the high tonnages extracted the expected utilisation of much equipment remains relatively low. To some extent this level of utilisation is influenced by the variability in conditions inherent in the mining process. This variability in production rates presents challenges to those attempting to design a coal clearance system. The difficulty is to design a system that has sufficient capacity to support production, without over capitalising or incurring high operating costs. The need to allow for a series of largely unplanned events in the design of a coal clearance system makes simulation modelling an ideal technology to employ. Simulation modelling is a methodology that allows a system with interacting components to be modelled over time, while explicitly taking into account unplanned events that may disrupt operations.This paper discusses how dynamic simulation models have been used to assist in the design of coal clearance systems. Typically this type of modelling has been used to look at the likely profile of production rates from the Longwall shearer and to determine how well various proposed combinations of belts, bins and stockpiles would support production.

Sep 26, 2011

By L A. Balzan, F Nieuwenhuys

GEOSCAN on belt analysers have been widely utilised in iron ore for nearly two decades. Since the first installations in 2003, the availability of accurate and reliable grade data has become standardised across iron ore mines in the Northern Cape in South Africa, where various streams are monitored continuously to ensure the optimal functioning of plants. Assmang Khumani has been at the forefront of technology adoption, and has implemented 19 GEOSCANs at various locations throughout the plant, monitoring run-of-mine, stockyard feed, beneficiation plant feeds, and products. Over the years, collaborative advances in the technology have allowed for numerous benefits and gains to be made. In recent times, there has been a concerted effort on the development of analysis for phosphorus in the material flows, and based on Scantech’s experience in the phosphate industry, this element has now been calibrated to achieve statistically acceptable and repeatable accuracies for real time analysis of this element on many of Khumani’s GEOSCAN analysers. This paper provides an overview of GEOSCAN use at Khumani, while focusing on the development of phosphorus analysis. A case study of analysis results is presented for a range of analysers that have been calibrated for this element, as well as a discussion on the benefits obtained as a result of this analysis.

Nov 8, 2021

By T M. Campos, H A. Petit, L M. Tavares, R Olympio

Much practical experience has been gathered in the last 30 years of application of high-pressure grinding rolls (HPGR) integrated with ball milling in size reduction of fine iron ore concentrates. The company Vale S.A, in Complexo de Tubarão (Brazil), was one of the pioneers applying the technology prior to pelletisation with an outstanding size reduction energy efficiency in the circuit and a significant increment in the specific surface area of the product. Recent studies by the authors demonstrated benefits of modelling and simulation to improve the performance of HPGRs in this particular application, with the model being able to describe HPGR performance under different operating conditions and under variations of feed size distribution. Despite these important advances, this modelling approach has only been used offline and under steady-state conditions. The present work applies the modified Torres and Casali model proposed by the authors in pseudodynamic simulations. The ability of the model to predict the characteristics of the product in real-time is evaluated using data available online for the pellet feed preparation circuit. Results demonstrated the model capabilities to map the physical operation and give a realistic representation of the process. Additionally, the model is demonstrated to be able to support the pellet feed production by providing extended real-time information of the process, making it a useful tool for improvement of the operational strategies and process stability.

Aug 24, 2022

The Shamrock Gold Mine has been brought from exploration to production within three years. Mining of the openpit is scheduled for June 1990 with commissioning in April of the 180 000 TPA carbon-in-pulp mill on old tailings and rock dumps. The development of a small openpit containing 344 000 tonnes at 3.6 g/t Au in a complex sulphide ore has required extensive metallurgical testwork to optimise recovery, and ensure profitability. The project has been undertaken in a changing economic climate, with increasing restrictive legislation. The decision to mine was further complicated by the escalating cost of installing a heap leach operation in South East Queensland. Decreasing costs of consumables, in particular sodium cyanide, and the opportunity to purchase a suitable transportable mill at a reasonable price made the project robustly viable as a CIP operation.

Jan 1, 1990