Search Documents

For Australian mining projects, sustainable groundwater use is typically defined as a groundwater extraction regime, measured over a specified planning time frame, which allows acceptable levels of stress and protects dependent economic, social and environmental values (DEH, 2004). This principle is compatible with most stakeholdersÆ understanding of our national environmental objectives, yet the application of this policy on a project-specific scale is not always straightforward. Three examples of sustainability issues in the management of groundwater in mining are presented. These examples highlight each of the three dependent values: environmental, economic and social.

Jan 1, 2006

By G Baird, M Seto

A low-cost methodology that allows the determination of in situ stresses using oriented core specimens has been investigated. The technique can be used to determine the stresses during the early stages of a project, even in undeveloped areas of a mine. The research aim was to compare the experimental results estimated by the Acoustic Emission and Deformation Rate Analysis methods with those estimated by conventional Hollow Inclusion cell measurements. The studies have been focused on full stress tensor determination from a single oriented rock core. In all cases the rock core specimens recollected the in situ stresses reasonably well compared with the standard overcoring method.

Jan 1, 2000

By D Kent, J Bullock, M Wilkinson

Over the last few years at Glencore’s Mount Isa Copper Operations (MICO) mining conditions have become increasingly challenging through lower head grades and higher work indices. MICO has had great success improving operating efficiencies and increasing productivity through focusing on technology, innovation and operational discipline. The recent implementation of the Mine Site Technologies (MST) ImPact System has supported the continued transformation of the MICO operations through improved personnel safety and direct measurement of productivity. The ImPact System has implemented new safety systems such as the heavy vehicle proximity detection system, underground personnel tracking system and emergency evacuation dashboards improving the overall safety of the workforce. The ImPact System has facilitated productivity improvements via real-time equipment and personnel monitoring, and the implementation of exception reporting (personnel productivity), KPI reports and production dashboards, and transparent reports highlighting developing maintenance issues.This paper discusses the components of the ImPact System, the current installation at MICO, and critically analyses the implementation processes and right sizing of the system to meet the needs of the business today and into the future.CITATION:Bullock, J, Kent, D and Wilkinson, M, 2017. Productivity and safety improvements supported by MST’s ImPact System at Glencore’s Mount Isa Copper Operations, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 279–286 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By C K. McKenzie, P Popov, B E. Papillon, I Kharitonenko

Flyrock produced by blasts in surface mining and quarrying is a major hazard that can result in serious injuries or property damage. This paper presents a fully integrated and automated approach for reviewing blast outcomes from a wide variety of rock blasting environments from the perspective of flyrock safety associated with blasthole collar ejections. The process is applied at a corporate level for an explosives service provider handling up to 100 blasts per day from mines, quarries and construction sites throughout the US.Flyrock risk minimisation has inspired research and the associated development of a reliable flyrock model to estimate flyrock ejection velocities and the resulting maximum projection distances of fragments. In spite of significant achievements in this area, flyrock incidents continue to occur, mostly due to implementation mistakes. An efficient preventive measure is continuous blasting process improvement that relies on on-site video recording, storage, automatic analysis and classification of the recorded blasts followed by the automatic generation of reports.In this paper, a novel blasting video analysis system that is capable of processing a large quantity of video records is presented. Blast analysis and parameter measurement are fully automated and are carried out using videos recorded with a conventional consumer camera. The blast video recording process does not require the use of surface markers, range poles or objects of a predefined size for scaling purposes.Although automatic video analysis is commonly used in many application areas, such as video surveillance, traffic monitoring and robotics, the algorithms that have been developed to recognise and track solid objects with well-defined shapes, textures and colours are not efficient at dealing with blasts, which, by their nature, have dynamically changing parameters. Moreover, very strong camera vibration caused by blasts that cannot be totally compensated by camera image stabilisers may cause conventional computer vision algorithms to fail.This paper presents novel computer vision methods developed for automatic tracking of the trajectory from a blast ejection point to the highest point reached by blast particles and the ejection velocity. The system also uses colour and motion analysis to detect the emission of toxic fumes during a blast. The solution is vibration tolerant and can differentiate foreground and background data, even in the presence of camera vibration. Moreover, the blasting video analysis method can automatically categorise correctness of the measurements and therefore indicate cases when additional visual inspections may be required to verify reports generated automatically.CITATION:Kharitonenko, I, McKenzie, C K, Papillon, B E and Popov, P, 2015. An automated system for flyrock and fume monitoring of blasts, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 417–424 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A Gustafson, G Shekhar, P Boeg-Jensen

The amount of material extracted from each blasted ring in sublevel caving mines is vital when deciding the overall mine production target. The orientation of the production drifts is normally perpendicular to the strike of the orebody, and rings are blasted from the hanging wall side to the footwall side in a retreating manner. For an inclined orebody, a given ring will contain different amounts of material based on its relative position along the production drift. This layout creates a distinctive problem with respect to the extraction ratio optimisation along the axis of the production drift. This paper describes the current drawpoint control strategy practiced at LKAB and presents the variation of drawpoint performance parameters along the production drifts. It uses automatically generated data from a bucket weighing system that measures tonnage drawn per bucket, and it classifies the blasted rings into four zones based on their relative position along the production drift. It considers the loading procedure for blasted rings at Kiirunavaara mine and analyses the variations in drawpoint performance along the production drift. The paper finds that although the current draw control strategy is sensitive to ring position along the drift, it could be modified to optimise the final extraction ratio.CITATION:Shekhar, G, Gustafson, A, Boeg-Jensen, P and Schunnesson, H, 2016. Draw control optimisation along the production drift in sublevel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 241–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A Noack

Today underground infrastructures, like tunnels and especially wide spread underground mines, are often equipped with ethernet based communication systems. These networks are used for the unified communication of data, voice and video. As these networks stretch along the major tunnels and in increasing scale also into the production areas, a high degree of coverage can be reached. For wireless coverage, standard IEEE 802.11 WLAN access points are being used. In order to provide a maximum availability and reliability, the active components are equipped with battery backup power supplies and the network infrastructure is set up in a redundant way using ring or meshed topologies. This provides a much higher availability compared to traditional phone systems or dedicated data links using a conventional star topology.Distributed computing intelligence that is installed on active network nodes throughout the whole network, additionally supported by a central server system, creates the basis for new mine safety functions introduced in this paper for both coal and non-coal mining. These new safety functions cover the detection of potential emergencies, using the status of the network as a æsensorÆ, as well as dynamically guiding people to safe exits or rescue shelters in case of an emergency. Furthermore, these functions are of important benefit for improving the efficiency of search and rescue operations following a major incident or accident underground.

Sep 26, 2011

By M S. Fenzel

Increased environmental regulations and pressures have created changing and new demands for tailings management strategies in a variety of mining applications. Critical among these items is the disposal of tailings as the pursuit of increased yields and lower costs have driven the application of different process technologies. With a number of technologies having a niche application focus, the belt filter press has been utilised for decades as a cost-effective and versatile option for dewatering different types of mineral tailings and other waste process streams. One of the critical advantages of the belt filter press is the technology’s ability to adapt and work in numerous plant designs, operating conditions and applications. As permitting and disposal options have become more stringent, plant designers, operators and equipment suppliers must develop comprehensive and site-specific economic, design and process evaluation techniques to ensure proper equipment selection and system design for belt filter presses or any other dewatering technologies. This paper will explore these techniques in relation to belt filter presses (with reference to other technologies) in a variety of different applications, along with other considerations to ensure a successful tailings dewatering system and disposal design. Summaries of equipment performance characteristics, operating and maintenance strategies and optimisation techniques will also be addressed in conjunction with the belt filter press’s adaptability to different plant designs and the resulting tailings characteristics.CITATION:Fenzel, M S, 2015. Analysis and adaptability of belt filter presses and other technologies for tailings dewatering over a range of mineral processes, plant designs, conditions, regions and operating philosophies, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By N Akizawa, A Tamura, S Arai

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Reaction products between high-temperature hydrothermal solution/uppermost mantle peridotite or lowermost crustal gabbro have been reported along Wadi Fizh of the northern Oman ophiolite; they are named as ‘mantle diopsidite’ and ‘crustal diopsidite’ respectively (Figure 1).The mantle diopsidite contains Cr-rich minerals like chromite, Cr-rich diopside (<2.5 wt per cent Cr2O3) and Cr-bearing grossular (<7.0 wt per cent Cr2O3). The chromites are varied in shape in the mantle diopsidite, euhedral to anhedral chromite grains contain globular inclusions of grossular and chlorite, and film-like chromite veinlets branch off from partially dissolved coarse chromite grains. In the crustal diopsidite, fine chromite grains are included in oscillatory-zoned skeletal uvarovite, especially in its high-Cr zones. The uvarovites are rich in rare earth elements (REEs). Direct laser ablation – inductively coupled plasma – mass spectrometer (LA-ICP-MS) analysis of the primary fluid inclusions detected Na, but not K.Our detailed studies of Wadi Fizh diopsidites clarify that the high-temperature hydrothermal solution dissolves chromite grains at the uppermost mantle section and precipitates hydrothermal chromite at the lowermost crust section. In addition, REEs were mobilised in the hydrothermal solution together with Cr. The hydrothermal solution involved in the diopsidite formation is assumed to have been rich in NaCl, and could mobilise appreciable amounts of Cr and REE.CITATION:Akizawa, N, Arai, S and Tamura, A, 2015. Chromium and rare earth elements mobility by sodium-bearing high-temperature hydrothermal solution – an example from mantle diopsidite and crustal diopsidite, in Proceedings PACRIM 2015 Congress, pp 291–296 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

THE following paragraphs represent an endeavour to describe, briefly the equipment used for the manufacture of sulphuric acid and superphosphates by the Corporation.SULPHURIC ACID PLANTS.Two separate units are in operation, No. I Plant working on sulphur dioxide generated from pyritic ore, No. 2 Plant working on sulphurous gases obtained from the Huntingdon-Heberlein desulphurizing process. The latter plant is unique in being the first installation for the successful use of these gases.

Jan 1, 1918

By S Slouka

Airborne rock dust poses serious long-term health complications to workers in the underground mining and civil environment where rock excavation is utilised. During drilling, airborne rock particles are immediately released into the breathable environment where additionally, the settled dust can be reintroduced into the air further down in production. The purpose of this study is to build a characterisation suite of dust particles such that underground operations can implement more appropriate dust suppression and mitigation techniques in accordance to pick wear. Therefore, concrete is cut to create a preliminary dust characterisation baseline, where future cutting tests will be performed on limestone and sandstone rocks.In this study, three conical pick wears (new, moderately worn, and fully worn picks) are used to generate dust from a concrete block and characteristics are statistically compared between the dusts. Airborne respirable particles are collected during cutting and deposited fine material, orparticles left on the surface of the block, are collected after cutting. The dusts are then analysed through standardised methods, field emission scanning electron microscope image capture with image analyses, and laser diffraction methods. Findings reveal that the worn pick generated thehighest concentration of respirable dust, all picks generated dust containing quartz, the three picks generally generated respirable dusts with similar particle shapes (in terms of roundness, roughness, and aspect ratio), and the worn pick generated the largest deposited fine material particles.

Oct 12, 2022

By Z Li, D Chalmers, J M. Tenney

This paper presents the findings and analysis of the investigation of effectiveness of thin spray-on liners (TSLs) as a gas management tool in underground coalmines. The project involves spraying TSL on the area surrounding gas drainage holes whereby the TSL acts as a thin membrane decreasing the permeability of the coal. This restricts air migrating through the coal seam and diluting gas from the drainage holes. There are a number of potential benefits from this technique but key points are that gas drainage holes produce gas with higher concentrations of methane. The design and execution of a field trial to investigate the effectiveness of a TSL on purity of in situ methane from gas drainage holes is presented in this report. For eight drainage holes, the results show an average increase in methane purity by 9.14 per cent and a reduction in air contamination by an average 7.93 per cent. Overall methane flow rate decreased by 27.6 L/s; however, flow rates were unreliable due to poor measuring equipment. For most holes, methane purity was not changed significantly; however, certain boreholes were responsible for most of the variation in methane purity. The boreholes showing a dramatic improvement in methane purity were likely those with intersecting cleats covered by the TSL. If the TSL was sprayed over more area, specifically in areas where the cleats are intersecting with holes, it is likely that purity of methane in the drainage holes will increase.CITATION:Tenney, J M, Chalmers, D and Li, Z, 2015. Thin spray-on liners potential in reducing dilution of in situ gas in underground coalmines, in Proceedings The Australian Mine Ventilation Conference, pp 323–328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By M Jacobs

This abstract discusses a heap leach copper mine that was failing to perform and as a result was not meeting targeted production. The mine had numerous technical challenges including: high water inflows, low levels of geotechnical monitoring, performance issues with mining, resource model and grade control reconciliation issues, and unexplained low levels of performance from the heap leaching operations. A team from various organisations with specialist skill sets including: a forensic accountant, the owner’s representative and a mining engineer, was arranged to visit the site. The task was to investigate the situation and determine what could be done to turn the performance of the mine around. After an initial assessment in late 2018, efforts were directed to better understanding the operations and improving the performance of the site through preventative management. A key part included the creation of production forecasts that could be achieved that would help restore confidence in the operations. Uncertainty in the mine achieving production forecasts and the performance of the heap leaching operations were contributing to the decline of the operations. Investigations uncovered the fact that while the resource model could reliably predict total copper, a lack of sequential leach data meant the accurate prediction of soluble and insoluble copper species, both important for heap leaching, was difficult to do with any degree of certainty. The crushing and mining contractors also appeared to have suffered somewhat from a lack of management by the owner’s team and performance had affected the production of copper. Collaboration and management were used by the team to understand and stabilise the operations. Ongoing collaborative efforts by the management team, site personnel and contractors resulted in a positive outcome for the owners and their mine – and could at yours.

Jun 22, 2022

By S Ravn

Under platform exhaust (UPE) systems are often designed into metro stations as a means of removing heat generated by trains as they come to a halt in the platform. These systems are designed to extract heat from the brakes and brake resistors directly at the source in order to capture as much heat as possible before it can enter the public areas of the station, or contribute to the temperature build-up in the tunnels. Due to space requirements for the associated duct and air handling units, the UPE plays a significant role in the geometric design of the platform and station as a whole.In recent years questions have arisen as to the effectiveness of UPE systems. However, very little data is available for designers to use when making important decisions on the station designs for new metro systems. This is important as significant savings could be achieved by omitting or re-designing these systems for new build stations; not only due to the capital costs of space provision for the duct itself but also due to the associated operation and maintenance cost of the UPE system.This paper will present recent measurements of the UPE system of the Copenhagen metro together with one-dimensional (1D) simulations, looking at typical dispersion of heat into the station plenum box and air exchange through draught relief shafts as the train enters the station in order to evaluate the effectiveness of the UPE system. The aim of this paper is to disseminate the results of measurements and analysis to increase awareness of the issue and to provide discussion relevant to designers in their evaluation of heat removal systems in new build station designs.

Mar 8, 2011

By D P. Blair

The theme of this conference is blasting productivity. This article only considers the technology aspect of this theme, and in particular, the collection and analysis of experimental data. In many cases, field trials are set up to collect data on variables such as fragmentation and vibration with the aim of comparing different explosive products and/or blast designs. An important aspect of such trials is the collection of sufficient data to draw sound conclusions. In this regard, there is no doubt that the scatter in real data is the root cause of all problems of obtaining misleading results due to an insufficient number of trials. This article shows that the typical one-off trial has a high probability of producing misleading information, which could be considered to be worse than having no information at all. Assuming that sufficient data has been collected, this article also highlights the methods that can be used to make the most of that data. These methods include the application of appropriate statistics that are dependent on the nature of the scatter in the data, and the use of some of the more recent filtering and spectral approaches that can be used to reduce the noise in measured blast signals and increase the resolution of their spectral characteristics.

Nov 8, 2011

By M Dietrich

The paper describes an efficient method for analysing the different attachment kinematics of excavators and other linkages by taking into account digging forces, the workspace and the stability of the machines. The different attachment kinematic systems of hydraulic excavators and a æclassical analysing methodÆ will be presented. The method was integrated as a plug-in for the multibody simulation (MBS) software MSC.ADAMS to create an easy to use solution for design engineers. A comparison of the new MBS-solution with the classical static analysis is a part of this paper and shows the advantages of the new method. This takes into account the manifold and new dynamic analysing opportunities, as well as more detailed models leading to more accurate results.

Sep 26, 2011

By I Sucholutsky, D M. First, D Mogilny, F Yusufali

Machine learning is creating value in all facets of the mining industry, from exploration to production. The authors provide an accessible, high-level introduction to artificial intelligence (AI), machine learning (ML), and deep learning (DL); the latter being widely recognised as one of the most powerful forms of ML. In particular, the authors will introduce deep learning models known as convolutional neural networks (CNNs), how they are applied, and the economic considerations necessary for determining when DL may be the right solution to de-risking complex block modelling problems. The authors present preliminary results from the mineral resource modelling study of the Jundee orogenic gold deposit, Yandal belt/gold province, Western Australia. The primary goal was to identify the direction and location of the narrow gold veins more accurately and demonstrate how non-linearly correlated elements are used as direct inputs to the resource model to assist with the target element’s grade prediction. This demonstrates that: (1) existing techniques for finding correlations between assayed elements do not adequately reflect the complex geology of the asset, (2) nonlinear correlations that are difficult to model as simple mathematical functions are representative of geological patterns in a deposit, and (3) non-linearly correlated assayed data, fed as inputs, increase the performance of the resource model as reconciled through blind tests. To conclude, the authors hypothesise that the patterns represented by the DL block models may be revealing the results of overprinting geological processes that generated mineral deposits. For example, the primary hydrothermal processes that deposited metals created depositional patterns that become particularly complex as a result of being overprinted, in part or in whole, by secondary physicochemical processes. This may explain why non-linear geochemical relationships have the capacity to generate more accurate block models of mineral deposits.

May 24, 2023

By V Rodríguez, M Hormaza, R J. Romañach, C Pinzón-de la Rosa

The authors have presented their ideas for developing a powder sampling device in the I-Corps™ program sponsored by the National Science Foundation (NSF). This is an intensive customer discovery program developed to increase the economic impact of the research sponsored by NSF.The I-Corps™ program requires performing at least 100 interviews with potential customers in various industries. These interviews are essential to establish the need for a particular product or solution, and identify potential commercialisation partners and competition. The interviews have revealed the absence of Theory of Sampling (TOS) principles in many companies. The interviews are designed to identify the difficulties associated with current sampling practices that do not meet TOS principles.The I-Corps™ program is a significant challenge for scientists who often avoid discussing a concept in fear of losing their research idea. The program teaches how to obtain information without releasing the important intellectual property related to a product development idea. The I-Corps™ methods have been used to discover the prevailing ideas on sampling in various industries.I-Corps™ also teaches how to present ideas to investors; another significant challenge for a scientist. We are currently learning to present sampling and TOS to investors and business development experts, and will share some of these experiences.CITATION:Pinzón-de la Rosa, C, Rodríguez, V, Hormaza, M and Romañach, R J, 2017. Theory of Sampling meets the National Science Foundation I-Corps™ program, in Proceedings Eighth World Conference on Sampling and Blending , pp 351–354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By K G. Fleetwood

This paper proposes an approach to determine the influence of non-ideal detonation characteristics related to the charge diameter, explosive type and confinement conditions on the available shock energy of ANFO and a representative chemically-sensitised (gassed) emulsion. The proposed degrees of non-ideality of the two different blasting agents are indicated by the Gurney ratios, determined from existing cylinder expansion testing data. The influence of the non-ideal detonation properties on blast design and performance are also compared using a series of theoretical, equal powder factor open pit blasting patterns with hole diameters ranging from 102 mm to 270 mm. The non-ideal shock energy factor (NSEF), which is the available shock energy per tonne of blasted material (MJ/t), is used to compare the different blasting patterns as charged with either ANFO or the gassed emulsion of equal charge density (0.85 g/cm3). The intended purpose of this investigation is to provide explosive users with an approach to compare different explosive types or charge diameters in the absence of dedicated non-ideal detonation modelling, which is generally not available to explosives users.The results of the comparisons suggest that at low charge densities, the example gassed emulsion displays a higher velocity of detonation (VOD) than ANFO in smaller charge diameters but similar degrees of non-ideality (based on proposed Gurney ratios). The results also suggest that the confined, non-ideal gassed emulsion VOD at hole diameters greater than 270 mm can be less than ANFO due to the low density effects on the emulsion matrix. The differences in non-ideal detonation properties and Gurney ratios between the ANFO and gassed emulsion resulted in gassed emulsion NSEF values ranging from 15 per cent lower to 65 per cent higher than ANFO for equal powder-factor patterns in blasthole diameters from 102 mm to 270 mm.

Nov 8, 2011

By R J. Wood

Raise drilling (or raise boring) is not a new technology or methodology. The first raise drilling machine was developed by The Robbins Company (TRC) of the USA in 1962. TRC manufactured the first tunnel boring machine (TBM) in 1952 and Jim Robbins, the founder of the company wanted to ‘turn the TBM concept on its head’ so to speak.Many improvements have ensued in the 50 years since the first machine. Such improvements include advances in the drill rod and thread design, cutters and reaming heads. Raise boring would not have been possible without the development of the tungsten carbide insert cutters and there have been big advances in both the carbide technology and in the mechanical design of the cutters.Over time mines have developed deeper with a greater use of diesel equipment resulting in greater ventilation requirements. This in turn means larger and deeper ventilation shafts. There have also been improvements in directional drilling techniques. This all combines with the need and ability to construct larger shafts using the safe method of raise drilling. With suitable geotechnical conditions the RBR900VF is capable of drilling shafts to a diameter and depth of greater than 8 m and 2000 m respectively. Greater diameters are possible over shorter lengths with suitable ground conditions.The RBR900VF was designed and manufactured to specifications developed by Macmahon. This machine has the greatest thrust and torque capability of any machine in the world. It enables cutters to be more heavily loaded in the larger diameter heads and this is essential for efficient rock excavation. Additional features of the new machine include minimal manual handling to provide a safer working environment and higher strength steel for the drill rods providing additional safety margin.CITATION:Wood, R J, 2014. A revolution in raise boring – the development of the RBR900VF, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 171–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By R A. Anand, N N. Viswanathan, M M. Pande

Slags are the most voluminous solid by-products generated in pyrometallurgical operations, and, as such, finding an application for these oxidic materials is pertinent to maintaining resource efficiency. In particular, pyrometallurgical copper production is associated with high slag rates, typically ranging from 2.2 to 3.0 tons of slag per ton produced copper, which necessitates slag valourisation. A possible application for these iron silicate slags is as supplementary cementitious materials (SCMs), which effectively lowers the CO2 emissions per ton of cementitious material. Although utilising iron silicate slags as SCMs has been studied in previous work, the scientific literature has limited data on the effect of composition on the inherent reactivity in cementitious systems. More specifically, no reports on the impact of FeO/SiO2 ratio have been presented in previous publications. Therefore, the present study aimed to isolate this parameter in a synthetic FeO-SiO2-Al2O3-CaO-MgO-Cr2O3 system. Since the amorphous content is a pertinent parameter for SCMs, a high-temperature confocal laser scanning microscope (HT-CLSM) was utilised to assess the crystallisation behaviour at continuous cooling conditions. Furthermore, high-temperature rheological experiments were conducted to measure the viscosities of the slags in relation to the crystallisation behaviour. The experiments showed that depolymerising the slag by increasing the FeO/SiO2 ratio generated a less viscous slag, which showed higher tendencies for crystallisation. Furthermore, experiments assessing the inherent reactivity as an SCM showed that depolymerising the slag by increasing the FeO/SiO2 ratio as the sole independent parameter generated an initially more reactive slag. However, replacing SiO2 with FeO was found to negatively affect the reactivity as measured over seven days within the tested compositional range.

Jun 19, 2024