Search Documents

A new plant for grinding limestone was built at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited to meet increasing process demands expected to reach 150 tonne/day of ground limestone. Plant specifications included open- circuit wet grinding, a single ball mill, a feed sizing of minus 6 Tyler mesh, a product sizing of 100 per cent minus 200 and 95 per cent minus 325 Tyler mesh and for the plant to be unmanned during normal running. Main features of plant and equipment are described; grinding performances given, as well as operating experience since commission- ing of the plant in March, 1976.

Jan 1, 1977

By Gemuts I, Hudson D. R

Massive sulphide mineralisation at the Miriam prospect, near Coolgardie, Western Australia, is fracture-controlled and associated with disseminated sulphides near the basal contact of an ultramafic lens. The lens is peridotitic in composition with a pyroxenitic zone at its base, and lies within a sequence of altered high-Mg basalts and pillowed tholeiitic basalts. Recrystallisation of the ultramafic rock has resulted in the development of secondary olivine. The average composition of the sulphide fraction of massive ore is Cu = 4.4%, Co = 0.3%, Ni = 23.0%, Fe = 31.8%, S = 40.6%, consisting of the supergene assemblage violarite-pyrite to a depth of 210 m.

Jan 1, 1973

It is well known that the ability to influence project value reduces significantly as planning progresses and decisions regarding project parameters are made. However, at the prefeasibility stage in particular, where one of the main aims should be to evaluate a wide range of options in order to select the best for more detailed further study, there is often a reluctance to spend the time and money needed to do this rigorously. This paper demonstrates, by a number of case study examples, how significant increases in value may be obtained by fully evaluating the combinations of alternatives for various project design parameters, including (though not limited to) mining methods, haulage methods, mining rates, processing methods and rates, sequencing of mining, and cut-off grades, with changes and upgrades over time where applicable. The additional value unlocked is typically orders of magnitude greater than the additional cost of the more comprehensive study. The dangers of misuse of simplistic sensitivity analyses and failure to identify how strategies might change in response to changes in external factors are also illustrated, and the importance of selecting the best ægrade descriptorÆ is discussed.

Jan 1, 2007

By D van der Spuy, T Kewe, K Keet, N Moffatt, A P. Paine

The Blue Cube Mineral Quantifier Inline (MQi) instrument uses reflective light spectroscopy and advanced chemometrics to measure mineral or elemental grade in a slurry line. The instrument takes scans continuously and sends data to the DCS or PLC control system.Controlling the concentrate grades on a flotation circuit using low-frequency measurements can be difficult or impossible, especially on a circuit that has fast process dynamics. The ability to rapidly measure changes in grade makes it possible to continuously manipulate the flotation circuit operating parameters such as level, airflow and reagent addition set points to optimise plant performance throughout changing conditions.At Barrick’s Porgera mine in Papua New Guinea the flotation circuit feeds sulfide concentrate slurry to a pressure oxidation circuit. In order to maximise gold recovery in the flotation plant and increase performance in the pressure oxidation process, there is a stringent requirement to maintain a stable and optimum sulfur grade. The gold recovery is directly affected by the sulfur grade as most of the gold at Porgera is submicroscopic and associated with the sulfides (disseminated?pyrite).Porgera considered various points in the flotation circuit for installing Blue Cube analysers. This was part of a plant upgrade to improve process control. Due to budget constraints it was decided to initially only install one Blue Cube analyser on the final concentrate stream of the flotation circuit measuring sulfur, sulfides, gold and particle size. The accuracy of the calibration results were very good for all these properties. The sulfur measurement was used in an advanced control system to optimise and stabilise the grade. The paper presents comparisons between mineral grades determined using analytical laboratory analyses and the online Blue Cube data measurements, as well as benefits achieved by measuring grade online. An analysis of the plant data before and after installation of the Blue Cube and the advanced process control upgrade indicate that the flotation recovery increased by 1.98 per cent.CITATION:Kewe, T, Moffatt, N, Strobos, P, van der Spuy, D, Paine, A P and Keet, K, 2014. Evaluation of the Blue Cube MQi slurry analyser for application in an advanced control system for the optimisation of a gold sulfide flotation circuit, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 357–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Drinkwater DJ, Watsford RMS, Johnson NW, Munro PD

This paper describes the use of modelling and simulation techniques in the analysis and optimisation of grinding circuits at the Lead/Zinc Concentrator of Mount Isa Mines Limited.The objectives of the studies were to: -1. improve primary grinding circuit performance by reducing the production of -0.006 mm galena fines.2. maximise the fineness of grind in the second existing grinding power and pumping capacitie The study has shown that quantitative models can operations. The models described plant operation,,and simulated the effect of process changes on plant performanc The use of automated scanning electron microscope technology tcliberation characteristics of the major minerals in the Mount isa Lead/Li ore is also described.

Jan 1, 1985

By E Shilov, R Dixon, L Tovey

BHP Western Australian Iron Ore (WAIO) operations use a suite of slope monitoring systems which are deployed to operational areas based on the ground control risk. Slope Radars are one system used within WAIO, having recently deployed and integrated a network of 22 radar systems across the operations. The integration required the development of supporting network architecture, infrastructure, virtualised hosting, security protocols and a technology support model. This has enabled data transfer between the physical radar systems located in open pits, to on-site offices, a vendor supported remote control room in Indonesia and the WAIO Integrated Remote Operations Centre for data analysis and monitoring of system and displacement alarms 24/7. The typical technical skillset of a Geotechnical Engineer does not include the knowledge and capability to understand and develop the supporting IT infrastructure required for establishing an integrated radar monitoring network. This paper will provide a discussion of the technology considerations for integrating radar systems and highlight the importance of the developed partnerships between internal geotechnical and technology teams and the external vendor team to ensure a reliable, robust and scalable slope monitoring solution.

Nov 29, 2022

By S Hapugoda, J R. Manuel, M J. Peterson, A Poliakov, E Donskoi

The occurrence and deportment of manganese in a number of ferromanganese and Mn-bearing iron ore samples from supergene-upgraded deposits, as well as from magnetite banded iron formation (BIF) and magnetite skarn deposits, was characterised in order to provide a basis for improved understanding of the processing characteristics of different ore types and investigate the potential for development of a robust geometallurgical classification for Mn-oxide ores. An understanding of the Mn mineralogy in mixed Fe-Mn deposits is necessary to inform any attempt to separate the Fe and Mn during beneficiation and to understand and predict the behaviour of lump and fine ore products during processing.A suite of analytical techniques was utilised, including hand sorting of lump ore particles, optical microscopy, X-ray fluorescence (XRF)/inductively-coupled plasma mass spectrometry (ICP-MS) chemistry, X-ray diffraction (XRD), scanning electron microscopy (SEM)/electron probe microanalysis (EPMA) and gas and solid phase pycnometry, in order to elucidate manganese mineralogy, mineral chemistry and mineral textures. Manganomelane group minerals (eg cryptomelane, hollandite), pyrolusite and lithiophorite were the most common manganese oxides in the samples examined. From the microprobe work, there was evidence of probable substitution of Mn, as well as Al and Si, into the structures of goethite and hematite. Manganomelane minerals were often intimately associated with goethite, in particular, and a clarification of this association and the associated Si and Al impurities is fundamental for improved understanding of beneficiation and sintering behaviour of Mn-oxide ores. Due to the poor or very fine crystallinity of some supergene manganese deposits and of some Mn oxide minerals, in particular the extent of overlapping peaks and their variable mineral chemistry, XRD was a problematic technique to equivocally determine Mn mineralogy.For lower-grade, earthy, poorly microcrystalline ores the mineralogical and textural association between mixed Mn, Fe and Al (¦ Si) phases was also critical. The deportment and potential separation of these elements in these deposits, especially Al, was complex, as they were characterised by forms of æhydrousÆ cryptomelane with higher levels of Fe-Al-Si substitution, as well as intimate intergrowths of ochreous-earthy goethite (probably aluminous in part) with cryptomelane, lithiophorite and/or kaolinite.Trace amounts of alkali elements in ferromanganese deposits were considered likely to be preferentially structurally associated with Mn oxides, while lateritic deposits with significant amounts of lithiophorite could contain elevated levels of deleterious impurities; Co and Ni in particular.A combination of solid and gas phase pycnometry proved to be a useful technique for broadly discriminating hematitic, goethitic and mixed Mn oxide-goethite lump particles based upon differences in their envelope and apparent densities. Based upon these preliminary results and ongoing Raman spectroscopy work on manganese deposits sensu stricto, Raman spectroscopy is a technique considered to have promise during targeted research to better link the optical and compositional properties of ferromanganese ore particles. CT-scan (computed tomography scan) analysis could also be combined with Raman spectroscopy and pycnometry to link mineral composition, mineral texture, ore particle textures and particle porosity/permeability to the high-temperature processing behaviour of lump and fines products.CITATION:Peterson, M J, Hapugoda, S, Manuel, J R, Donskoi, E and Poliakov, A, 2013. Textural characterisation of manganese minerals to improve the geometallurgical characterisation of ferromanganese and iron ores, in Proceedings Iron Ore 2013 , pp 281-300 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By T Nassis, P Louw, M R. Fry, T du Toit

Business intelligence (BI) and business analytics (BA) are established IT technologies that are used extensively in the business environment. This paper discusses the use of these technologies in production environments and beneficiation plants.Assmang’s Khumani mine is an iron ore operation located in the Northern Cape, South Africa. Assmang Limited is jointly owned by African Rainbow Minerals Limited and Assore Limited. This paper presents a case study of a BI solution applied to this plant, which is used by metallurgists, supervisors and all levels of operations and management to extract and analyse data to control and optimise the operation of the plant.The main advantage of adopting an established BI solution is the ease with which production personnel can extract and analyse data. The data is easily presented in familiar spreadsheets and no IT staff or specific training is required to achieve this.The solution adopted at Khumani mine uses a data mart with a multidimensional model (called an online analytical processing (OLAP) cube) acting as the main repository and source of data. The OLAP cube simplifies the access and analysis of plant data.The OLAP cube stores data in a specifically-designed way, which allows extraction and analysis to be performed quickly. It is designed to hold large amounts of data on a long-term basis, which could be for the life of the plant. It also performs automatic aggregations over many dimensions on a background process.A major benefit in adopting such a BI solution is that it allows common BA methods to be applied. This is due to both the efficient long-term storage of data and the availability of standard BA tools. BA tools are now able to perform data mining, predictive analytics, forecasting and other machine-learning algorithms. This paper presents the possible use of such advanced data analysis methods in a beneficiation plant.CITATION:Fry, M R, Nassis, T, Louw, P and du Toit, T, 2015. The use of common business intelligence and analytics tools in the operation and optimisation of iron ore process plants, in Proceedings Iron Ore 2015, pp 129–138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A M. Lechner, V Glenn, M Edraki, D R. Mulligan, C Unger

With more than 50 000 recorded abandoned mines in Australia, effective management strategies are needed to prioritise and manage health, safety, environmental and socio-economic risks and opportunities. This paper reviews international leading practices for abandoned mine management and identifies key issues that need to be addressed in the Australian context. As well as the academic literature, this review draws on a 2008 global legacy site survey and forum in 2008, a Churchill Fellowship study of abandoned mines and the recently released æStrategic Framework for Management of Abandoned Mines in the Minerals IndustryÆ (MCMPR/MCA, 2010).A conceptual model was developed to identify the relationship between key issues affecting the management of abandoned mines in Australia. The conceptual model is then used in the development of a maturity chart which draws on risk management principles to provide leading practice guidance for abandoned mine managers, jurisdictions and stakeholders. The maturity chart approach for risk management has been successfully used elsewhere to evaluate safety, environmental and socio-economic maturity.CITATION:Unger, C, Lechner, A M, Glenn, V, Edraki, M and Mulligan, D R, 2012. Mapping and prioritising rehabilitation of abandoned mines in Australia, in Proceedings Life-of-Mine 2012 , pp 259-266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By R Goddard

An alternative stoping method has been adopted for narrow vein stoping at the Tasmania Mine in Northern Tasmania. Colloquially described as ‘Radial-in-Reef’ (RiR) stoping, the method employs the drilling of radial rings in the plane of the Reef from a drill stub located at the geographic centre of the proposed stope panel.Production from the Western Zone of the Tasmania Reef has been undertaken remotely from the Reef since 2007, after a detailed geotechnical engineering analysis indicated that the integrity of the sill drives could not guarantee an acceptable level of confidence should an anticipated seismic event occur within a radius of 10 m. The key tenet of the remote mining approach was the exclusion of personnel from sill drives once stoping had commenced. The remote mining method had to be ‘retrofitted’ to four existing stoping blocks totalling 11 sill drives which totalled 160 m vertically. The remote mining method proved to be complex, cumbersome and very expensive. However, the ore was extracted successfully.By early 2010, previously developed ore had largely been exhausted and the future development with an orebody open at depth presented the opportunity to review the current extraction method. However, the new extraction method needed to maintain the tenet of excluding personnel from sill drives of active stoping blocks, but seek opportunities to reduce the difficult and costly aspects of the previous method. The new ‘Radial-in-Reef’ stoping reduced the development requirement from six to two drives per ore block. Cost implications aside, the significant reduction in prestoping extraction ratio was expected to also reduce the likelihood of seismicity. Transverse production rings were designed to be drilled radially from a drill stub mined from a mid-stope footwall drive. Stopes totalling up to 7000 tonnes were planned be fired in a single electronic blast. Extraction was designed to take place from a basal sill drive under teleremote operation. At the time of writing, the method was under trial.

Mar 21, 2011

By A Fareth

Constructed between 1885 and 1891, the New Croton Aqueduct (NCA) in New York State is a 50 km long (31 mi) brick-lined tunnel conveying water from the Croton watershed north of New York City to distribution systems in the Bronx and Manhattan. Except at two siphons, the aqueduct operates as an open channel conduit from the New Croton Reservoir downstream 39 km (25 mi) to the Jerome Park Reservoir in the Bronx. The remaining 11 km (6 mi) is operated as a pressurised conduit and includes a major siphon, of circular cross-section, under the Harlem River. The aqueduct has a flow capacity of approximately 1100 million litres of water per day (13 m3/s or 290 million gallons per day) and supplies on average ten per cent of New York CityÆs drinking water. The CityÆs water supply system is operated and maintained by the New York City Department of Environmental Protection (NYCDEP). This paper covers the work done during the three main stages of the program to rehabilitate the entire NCA: inspections, design and rehabilitation. It also includes some of the more interesting structural findings of the original construction as well as documents and drawings from the NYCDEP archives. The rehabilitation program has been underway in phases since 1993, with inspections scheduled to minimise outages, allowing this strategic aqueduct to remain in service during critical seasonal periods. The open channel flow section of the aqueduct in the north is horseshoe shaped, with inside dimensions of 4.1 m (13.6 ft) in width and 4 m (13.5 ft) in height. The pressurised section is 3.7 m (12.3 ft) in diameter, and includes a 90 m (330 ft) deep siphon under the Harlem River. A total of 163 million bricks were used in the construction, enough to build a 48 km (30 mi) wall around Manhattan Island, 3 m (10 ft) thick and 15 m (50 ft) high.Between 1993 and 1997 a series of in-tunnel investigations were performed in the open channel portion of the NCA, consisting of field inspection, non-destructive geophysical testing, and coring of the brick liner. Between November 2004 and September 2005, a major inspection program was conducted to assess the condition of the 11 km (6 mi) long pressurised section and all shafts, headhouses and blow-off structures along the entire 50 km (31 mi) alignment. Inspection methods included using an underwater remote operated vehicle (ROV) equipped with sonar and cameras to inspect the deep siphon, fibre optics examinations of probe holes drilled through and beyond the brick lining, and core holes and geophysical inspections to assess properties of the liner and behind-the-liner materials. A water pressure and test grouting program was conducted to assess methods and expected grout takes for the rehabilitation work in the pressurised sections. The rehabilitation program is anticipated to be completed in 2010.

Jan 1, 2008

The hydrological cycle in nature, with particular reference to Australia . 2. The definition of water pollution drawing on the experience of several major countries. 3. A description of the pollutants in water, and why they are pollutants. 4. The classification of waters as defined by major overseas countries. 5. The criteria and standards developed by major overseas countries for the classification of waters. 6. A brief- summary of the legislation adopted by overseas countries for the control of water pollution, and of the organisation and administration of controls. 7. A study of Australian legislation and administration of controls of water pollution. 8. General observations and conclusions.

Jan 1, 1971

By M A. Vinokurova, V M. Mullov

Due to treatment of refractory carbonaceous low-grade gold ores a new technology providing improved precious metal recovery is required. For this reason, a technology including gravity, flotation, recleaning of the flotation concentrate, intensive cyanidation of the gravity concentrate and carbon in leach (CIL)-process for intensive cyanidation tailings and the recleaned concentrate was developed. The proposed technology allows to decrease preg-robbing activities of concentrates treated by subsequent cyanidation. Total gold recovery by the proposed technology from the ore with a head grade of 0.8 g/t was 83.9 per cent. The gold loading onto the activated carbon from CIL process was 6.500 g/t.

Jan 1, 2007

By Y Zhou, Y Liu, J-P Yang, P Wang, K Hu

"Large-scale mine reclamation has taken place recently in response to the implementation of mining regulations in China. Effective monitoring of the progress of reclaimed land is a critical procedure to assess the quality of reclamation program and to ensure that mining enterprises fulfill their reclamation responsibilities. The present paper reports a preliminary study that examines the situation of mine land reclamation monitoring. Based on the monitoring, some general requirements for mined land reclamation have been proposed, including: the monitoring should be systematic and comprehensive the monitoring should be adapted to specific local conditions the monitoring should be reasonably optimised via scientific methods and technology the monitoring should stick to a variety of national technical criteria.The aim of land reclamation monitoring is to evaluate changes of critical indicators closely reflecting the development trend of the reclaimed mined land, to develop or improve the criteria and technical parameters specific to the site, and to prevent secondary environmental degradation. Based on these requirements and aim, the monitoring should cover the progress of reclamation, establishment of vegetation and plant community development; and recovery of land and water quality in the reclamation area. Regulatory measures are proposed which would improve the work of mine reclamation monitoring in terms of regulation, organisation and financial support.CITATION :Wang, P, Yang, J-P, Zhou, Y, Hu, K and Liu, Y, 2012. The primary framework for the mechanism of the mine reclamation monitoring in China, in Proceedings Life-of-Mine 2012, pp 47-50 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By N Haque, S Northey

Water in mining, mineral processing and metal production on a life cycle basis has been at the top of agendas for various industries, government agencies, research organisations, academic institutions and communities. As a result, a number of water footprint assessment methodologies have been developed. However, their practical applications in mining and mineral processing industries with specific case studies are still rare.A key objective of the Minerals Down Under Flagship is to contribute to the long-term sustainability of the Australian mining and mineral industries. Researchers in the Mineral Futures theme have developed robust assessment methods to evaluate the impact of mining and minerals technology development on the environment. The future of mining and the mineral industry is strongly linked with its sustainability - better water management strategies will need to be implemented.Life cycle assessment (LCA) has been a recognised method for measuring the environmental impacts of products, processes and services. It provides a scientifically sound method of comparing products and processes using a common basis and identifies so called æhot spotsÆ and opportunities for reducing environmental impacts. The water footprint of mining, mineral processing and metal production using an LCA basis is still scarce in the literature. Research methodology is now being applied in detail for copper, gold and nickel. A primary focus has been the relationship between ore grade and water use for which mathematical models are being developed. These types of models provide inputs for LCA of mining and mineral processing plants and can identify water saving opportunities through scenarios and process route analysis.CITATION:Northey, S and Haque, N, 2013. Life cycle based water footprints of selected mineral and metal processing routes, in Proceedings Water in Mining 2013 , pp 35-50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By D Lucato, B Haase, R Saha, S Limberger-Forte, J Lishman

Cadia East Mining operations have employed geometallurgical techniques to advance the understanding of the in situ rock hardness variability across existing Panel Caves (PC). Geometallurgy advances the understanding of variability across an orebody through the integration of geology, mineralogy and processing response and therefore enhances spatial mapping of comminution or separation properties. Spatially extensive geometallurgical measurements are necessary so that continuous rock properties can be generated and used for the development of comminution and processing domains using geostatistical modelling. Standard testing protocol across geological and mineralogical domains is vital to understand the variability in deposit wide comminution and separation properties. The high cost and large sample requirements associated with metallurgical test work typically results in insufficient data density and distribution, making it difficult to model and map deposit scale variability. Quantitative hardness proxy tools are useful to measure in situ rock hardness, however this data is typically either sparse or missing within advanced mining operations. In recent years, mineralogy and multi-element assay data has often been collected as part of the standard geological data set and is generally coincident with metallurgical test work. In this paper relationships between mineralogy and comminution parameters have been applied to multi-element assay data with coincident measured Bond Work Index (BWi) data to generate a predicted BWi using linear regression. The predicted BWi is intended to supplement existing measured BWi data to enable better extrapolation across the deposit. Geostatistical Conditional Simulation methods have then used the predicted and measured BWi data to produce a BWi variable as a new input to the resource model. The simulated BWi can be used as an input for specific energy models to predict required grinding energy consumption across a deposit.

Mar 22, 2022

By J Ross

The foundation of effective leadership is communication. You can have all the leadership theories, models and training you want, but in the end it is all about leaders talking to, listening to and understanding the point of view of those below and above them.The foundation of effective safety is peoples’ behaviours. Every incident, every near miss and every safe act comes down to what one person does and how that affects themselves and others. We tend to focus these behavioural considerations on the people at the ‘coal face’, those most in harm’s way. But it is the individual behaviours of everyone in the organisation, particularly those at the top, which are just as (if not more) important. The foundation of effective safety leadership in the mining industry is that it starts at the top, with the individual behaviours of leaders. The behaviours of each and every leader will be reflected in their teams. And where their teams are made up of leaders, these leaders will pass these behaviours on to their teams and so on. It’s the sum total of what people see their leaders do and what they do as a result, that creates the ‘culture’ of the business – and it’s this culture that makes or breaks how safely people work.

Mar 21, 2011

By J Howard

Following discovery in October 2004, commencement of development in February 2007 and first ore production in mid 2007, the Trident gold deposit, located in the Eastern Goldfields of Western Australia, has now been successfully mined for over three years. Three years of operational history has enabled the performance of the Trident underground mine to be reconciled against the mine plan and strategy proposed for the original feasibility study.The Trident deposit, initially based on two lode systems known as the Eastern Zone and Western Zone, has been continuously drilled, interpreted and re-interpreted over the period and as a result the addition of the Athena, Apollo and Artemis lode systems as well as numerous smaller scale lodes has been realised. The first three years has seen the Trident underground mine quickly move up to its 1 Mtpa design production rate. The mine plan and strategy used in the initial feasibility study and subsequently implemented, required sufficient flexibility to enable modification and optimisation to mine plans as ore zones were further defined. The ability to modify the mining plans has enabled Avoca to achieve its mining targets at Trident. With over 250 000 ounces gold produced to January 2010, the company is well positioned to achieve its ten year vision associated with the Higginsville Gold Project.This paper offers an account of operational experiences whilst providing comparison to assumptions and methodologies used in the original feasibility study. The paper is a sequel to a paper presented at the Tenth Underground Operators’ Conference held in Launceston, Tasmania titled Development Strategy of the Trident Underground Gold Mine.

Mar 21, 2011

By P J. Fairfield

"This paper reflects on the author’s experiences in undertaking mining studies and reviewing mining projects and technical reports, particularly over the past five years, and the impact of recent changes in reporting standards and listing requirements pertaining to mining-related evaluation and valuation exercises. It also discusses contemporary changes in the expectations of the investment community and the implications for the role of the technical specialist in providing advice to such stakeholders.Not for the first time in history, the resources industry has experienced a significant downturn after a period of strong, sustained growth in line with the traditional view of the cyclical nature of commodity markets. The resource industry is currently faced with capital austerity in the wake of projects ‘failing’ (not delivering to expectations). In response, the industry has experienced changes in investment behaviour (slowing of investment) and an increasing regulatory burden as stakeholders seek a greater understanding of mining project risks.This paper discusses this response and uses case studies to highlight the key learnings (perhaps re-learnt) by the industry. It also discusses the challenges faced by technical specialists in communicating the results of technical and valuation studies to the investment community.As investors seek to take advantage of the current stage in the investment cycle, the key challenge of the technical specialist is to effectively communicate the uncertainty in technical assumptions, risks and opportunities that drive project value.CITATION:Fairfield, P J, 2016. Managing expectations – from buyer beware to buyer be aware, in Proceedings Project Evaluation 2016, pp 66–74 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By B W. Atkinson, J Docherty

An Australian Working Group has been compiling a guide for operators to use in order to improve the efficacy of their routine and non-routine sampling tasks within their coal preparation process. The guide focuses on unit operations within the process, and not conveyor belts or transfer stations that are adequately covered by the existing Standard ISO 13909.Representative sampling of unit operations is generally an after-thought following plant construction, whether that be a result of oversight, or more commonly, capital cost minimisation during initial construction. Minimising capital cost by avoiding adequate sampling systems is generally a poor decision, since the result is a process that cannot be adequately measured, meaning that it cannot be adequately managed and optimised.The use of the term ‘guide’ rather than ‘standard’ is intentional. Practical means of sampling unit operations within existing plants generally relies on a compromise between sample representativity (minimisation of bias) and sampling feasibility. The guide does not endorse poor sampling practice, but instead offers practical guidance to overcome, to the extent reasonably possible, real-life limitations.When it comes to sampling any particular process, it is almost always necessary to make a professional judgement as to whether or not the proposed samples are likely to be sufficiently representative such that the sampling will be worthwhile. Such judgement needs to be exercised by personnel who understand the principles of sampling, as they apply to the stream being sampled. There are many circumstances where available methods for sampling of a particular stream will be meaningless, and in such circumstances analytical data from that sampling will only serve to propagate poor decision-making.This paper outlines the approach for the guide, the areas it covers and the approaches adopted for different types of unit operations and associated equipment configurations.CITATION:Atkinson, B W and Docherty, J, 2017. A practical guide to sampling in coal preparation plants, in Proceedings Eighth World Conference on Sampling and Blending , pp 241–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017