Search Documents

INAP was formed in 1998 by a number of major mining companies, with a view to sharing acid rock drainage knowledge and experience, and to coordinate global research on the management of sulfidic mine wastes. INAP is now moving to further strengthen its global role by networking with regional organisations that are active in the area of ARD, including MEND 3/NEDEM 3 in Canada, the ADTI in the USA and ACMER in Australia. The INAP-Regional Organisation partnership will be formally launched at the 6th ICARD.

Jan 1, 2003

By R Jones

OneSteel Whyalla’s grate-kiln-cooler pelletising plant was commissioned in 1968 processing haematite feed from the local South Middleback Ranges mining area. The existence of a magnetite resource beneath the haematite ore at Iron Duke had been known for some time. In 2004, a decision was made to covert the primary iron source for the Whyalla steelworks from haematite to magnetite – known as project magnet. The intent of the project was to convert the feed to the steelworks from haematite to magnetite and to free up the remaining haematite resource for export. The pelletising plant was cut over to a magnetite feed in 2007.The thermochemical differences of magnetite compared to haematite are threefold:1. the introduction of an exothermic reaction during conversion of magnetite to haematite,2. the absence of bound water which existed within the haematite, and3. lower gangue content requiring lower fluxing levels and therefore lower calcination energy demand.The combination of these differences results in a significantly different induration requirement for magnetite as compared to haematite. The change therefore required extensive research and test work to design modifications to the furnace and to ensure appropriate risk mitigation for the Whyalla steelworks.Preliminary pot-grate test work was performed to define the pellet chemistry and confirm the suitability of the magnetite to produce pellets suitable for the OneSteel blast furnace. A heating curve was developed by use of computer-based heat and mass balance modelling. Extensive pilot scale grate-kiln-cooler test work was then performed to confirm the heating curve and to verify and fine-tune the pellet properties. Computation fluid dynamics was used to design the physical changes to the furnace required to achieve the proposed heating curve.Following installation of an additional preheat zone, including a wall and dilution air fans, into the preheating furnace, and installation of an additional wall into the cooler, the modified furnace was commissioning in December 2007. The plant performed as expected during commissioning with the actual heating curve matching the proposed curve and the produced pellets within blast furnace specifications.

Jul 11, 2011

By G Harbort, D Zoetbrood

"The Phu Kham copper-gold operation in the Laos People’s Democratic Republic (PDR) is owned and operated by Phu Bia Mining Limited. PanAust Limited holds a 90 per cent interest in Phu Bia Mining Limited, with the remaining ten per cent held by the Laos PDR Government.The original 12 Mt/a copper-gold concentrator at Phu Kham commenced production in April 2008. An incremental improvement program resulted in a number of circuit changes being incorporated by 2011, including conversion of conditioning tanks to flotation cells and the installation of a Jameson Cell cleaner scalper. In 2012 the Phu Kham Upgrade Project was commissioned to increase throughput to 18 Mt/a. In April, 2013 the Phu Kham Increased Recovery Project was commissioned to maximise performance by debottlenecking the plant IsaMill™ regrind and cleaning capacity.With the variable mineralogy of Phu Kham ore, control of the c concentrate regrind circuit is essential in terms of achieving effective liberation to maintain concentrator performance. On a routine basis laboratory regrind signature plot data is compared with daily surveys of the operational IsaMills™. More extensive surveys are also conducted to determine size distribution on a mineralogical basis and the effect of fine regrinding on pulp electrochemistry and flotation performance. This paper provides a review of the operating performance of the Phu Kham IsaMills™ with regard to power draw, feed and product size distribution, feed per cent solids, mineralogy and pulp electrochemistry. Operating performance is compared with the IsaMill™ signature plot test for predicting performance.Citation:Harbort, G, Zoetbrood, D and McNab, B, 2016. Operating Performance of the Phu Kham IsaMill™, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 39–50 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By S Grobler, T Fares

Understanding the real utilisation of the available volumetric capacity of a conveyor is key to unlocking latent capacity or ‘debottlenecking’ existing plant. Conveyors are typically designed on the basis of conservative density and ore surcharge angle specifications, and consequently there is often latent volumetric capacity available.Laser scanning measurements of conveyor ore profiles has been undertaken on iron ore conveyors to gain an understanding of the actual surcharge angle and the available edge clearances. Iron ore producers seeking to extract maximum production from their assets have used these measurements to debottleneck existing plant and to revise the design criteria for future plant. The benefit is that latent capacity of existing plant can be unlocked and smaller and cheaper conveyors can be designed for future plant, maximising the return on capital. This paper describes the measurements and results.CITATION:Fares, T and Grobler, S, 2015. Laser scanning of conveyor ore profiles, in Proceedings Iron Ore 2015, pp 549–554 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A McCallum, J Abols, G Patrick, G Johansen

The authors challenge the traditional thinking that whole ore cyanidation followed by Carbon in Pulp (CIP) or Carbon in Leach (CIL) should be applied as a standard process in the majority of gold processing flow sheets. The concept of whole ore leaching by using cyanide can result in unnecessary environmental and capital risk. Alternative, currently available technologies can be used to provide the desired level of gold recovery at a much lower installed cost and less impact on the environment. Gravity concentration, alone or in conjunction with flotation, can produce a gold bearing concentrate that can then be fed directly to a batch or continuous intensive cyanidation unit. The In-line Leach Reactor (ILR) is an intensive cyanidation unit developed by Gekko Systems of Australia. Advantages of this technology include significantly reduced capital outlays for greenfield plants or plant upgrades and increased investor returns. Reduction of onsite cyanide and carbon inventories improves plant safety, materials handling and site security. By using direct electrowinning to treat the gold bearing solutions produced by the ILR, the need for a conventional carbon stripping circuit is removed. Potential also exists to increase grind size û saving energy, further reducing capital and operating costs and decreasing the environmental impact of a mill. Detoxification of cyanide before the release of solution to the tailings dam can minimise tailings disposal and containment requirements. When used in the right application the proposed process will have little or no impact on gold recovery and may actually increase recovery for complex ores. Areas applicable to this type of treatment include: plants in environmentally sensitive regions, lower tonnage higher grade deposits, coarse gold deposits, and preg robbing ores û some of which may not currently be economically feasible using standard processes and flow sheets. We have provided two examples of such projects, where an alternative to whole ore leach and CIP or CIL has the potential to deliver these benefits.

Jan 1, 2004

By M Fritz, B Ziegelaar

"For moisture samples, the International Standard for iron ore sampling states the following: Moisture samples shall be processed as soon as possible and test portions weighed immediately. If this is not possible, samples shall be stored in non-absorbent airtight containers with a minimum of free air space to minimise any change in moisture content, but should be prepared without delay. ISO 3082 (2009)Prescribing what to do is of course easy. Putting it in practice is, however, a little more problematic.The iron ore industry has seen quite some changes in the last ten to 15 years, such as: a large increase in the volume of seaborne trade new ore types and blends coming onto the market new mines, processing plants and port facilities producing more and loading faster an increase in wet processed ore products a dramatic rise and then equally dramatic fall in the iron ore price followed by a recent recovery.All of the above have had an effect on sampling facilities. The large increase in volume coupled with ambitions such as labour efficiency, safer operations and higher precision has driven the installation and retrofitting of automated sampling and robotic sampling preparation plants in order to keep up with increased quality control.Designers of sampling facilities are invariably instructed to build plants that comply with ISO 3082. In general this means that the plants are compliant in respect of the number of primary increments, gross sample masses and sample division rules. The clause at the beginning of this abstract is mostly overlooked as it only appears in a section (4.1) describing the basic requirements of a sampling system.An error of 0.1 per cent in moisture changes the value of 1 Mt of iron ore at US$50/t by US$50 000. At 700 Mt/a of Australian iron ore exports, this is US$35 M. Frequently, errors from 0.5 to 1 per cent in moisture measurements are encountered.In comparison an error of 0.1 per cent Fe is US$0.081 (US$50/t and 62 per cent Fe base) per tonne, that is US$81 000 per Mt or about US$51 M for the same Australian annual iron ore exports.It is somewhat mystifying that we in the ISO Technical committees spend extraordinary energy (= money and time) on improving measurement techniques, whilst the big costs are in sampling errors. This is particularly true for moisture measurement. Our paper quantifies some of the sources of moisture measurements errors and suggests mitigating actions.CITATION:Ziegelaar, B and Fritz, M, 2017. Sampling for the percentage moisture in the iron ore industry, in Proceedings Eighth World Conference on Sampling and Blending, pp 271–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

By T Walsh, S R. Mudnuru

The development of lithium-ion batteries, coupled with the global trend towards electrification of transportation, has led to a dramatic increase in the demand for lithium. The production of lithium from hard rock ores is increasing, and flotation has proved to be an effective means for the beneficiation of many pegmatitic lithium ores. Clariant Mining Solutions has developed a range of novel collectors for the flotation of spodumene and other lithium ores, and this paper presents examples of some of the most recent developments. Fatty acids are the typical collectors for lithium flotation, however the grade and recovery achieved with these collectors is often below the desired level. There are also some significant drawbacks associated with the use of fatty acid collectors, such as the formation of calcium soaps which give rise to filtration problems and the need for acid washing. Several FLOTINOR products have been developed as alternatives to fatty acids. These products offer equivalent or better metallurgical performance at significantly lower dosages than fatty acids. This offers benefits to the flotation circuit as well as potentially reducing the issues associated with downstream processing of the concentrate.

Aug 24, 2022

By N J. Potter, N W. Brand, J M. F Clout

The increasing demand for iron ore with low concentrations of trace elements, puts increasing pressure on iron ore producers for high-quality material. Understanding the mineralogy, petrography, chemistry, and mineral association of iron ore deposits is becoming increasingly important to provide iron ore products that meet the ever-increasing standards of steel mills. Limited attention has been paid to documenting new orebodies beyond bulk RC drill chip assays and product specification data. Therefore, limited information is known about the spatial distribution of minor and trace elements at the hand specimen scale, and elemental deportment within different ore and gangue minerals. In this study, samples from high-grade microplaty hematite, supergene-enriched martite-goethite and hematite iron ores are examined for their elemental and mineral associations. These samples contain distinctive minor and trace element distributions, with the mapping of deleterious elements (eg Zn, As, Cu) enabling the deportment and abundance within the ore and gangue minerals to be assessed. Results from this study show a diverse range of minor and trace mineralogy that are present in typical iron ore samples, in abundances below the detection limit of routine XRD scans, that host the deleterious elements, including but not limited to, sphalerite (Zn and S), chalcopyrite (Cu and S), xenotime (P and Y), apatite (P and Ca), cryptomelane (K and Mn), barite (Ba and S), alkaline feldspar (K, Al and Si) zircon (Zr and Si) and chromite (Cr and Al). The presence of these minerals and associated deleterious elements, even at low concentrations, has implications for producers, with the ongoing restrictions and tightening of environmental constraints in shipped iron ore products. By understanding the distribution and location of these elements within the iron ore, steps can be considered to maintain increasingly higher quality iron ore supply around the world.

Nov 8, 2021

By O van Baalen

The Ernest Henry Mine is a copper-gold open pit operation situated in northwest Queensland, Australia. It is owned and operated by Xstrata Copper, with a current throughput of 11 Mtpa, however, open pit operations are scheduled to cease in mid 2011. The deposit dips approximately 45º and extends for at least another 400 m vertically below the final 530 m deep pit design.Construction and development of a sublevel caving (SLC) operation beneath the open pit was approved in December 2009. The feasibility design requires 39 km of development to be completed prior to production, which will commence in the fourth quarter of 2011. Initial ore production will be trucked and will increase to 3 Mtpa by the end of 2012, after which a hoisting shaft will be used. Ore production will then increase to 5 Mtpa in 2013 and ultimately to 6 Mtpa in 2016.Two 3000 kilo watt of refrigeration (kW(R)) modular refrigeration plants will be installed, as well as two 1600 kW mixed-flow fans capable of a combined flow rate of 780 m3/s at a total pressure loss across the mine of 2000 Pa. The main fans will be installed underground and will exhaust into the base of the pit.The following challenges were faced in the development of the ventilation and refrigeration network:•a relatively steep geothermal gradient,•tropical ambient conditions,•working under a wide pit shell, and•a large underground trucking fleet prior to shaft commissioning.A considerable number of ventilation studies were conducted with later studies extensively using Ventsim Visual™ mine ventilation software to complete the design process of the ventilation and refrigeration networks, including the comparison of several alternative designs. The paper focuses on design challenges prior to the commissioning of the hoisting shaft, and discusses resistance optimisation and occupational hygiene-related design parameters, such as heat and diesel emissions, production level ventilation, main fan selection and location, and refrigeration requirements.

Mar 21, 2011

By J Pan, B-J Shi, X-B Li

The granulation behavior of specularite fines which possess poor ballability was studied with limonite fines as a function of nuclei particles and adhering fines. The results show that the permeability of granules deteriorated as the ratio of specularite fines increased in the mixture, and the optimal granulation moisture content also decreased. The granulation kinetics results demonstrate that the adhering load of specularite fines increases rapidly within three minutes and then levels off. With increasing specularite fines ratio, the adhering speed is accelerated but the granulation duration needs to be longer to reach adhering balance. The microstructure of granule quasi-particles indicates that the fine limonite particles act as binders to bond together the specularite particles which are dispersed in the adhering layers. This can improve the adhering strength of the granules. Hence, the granulation behaviour of specularite fines can be improved by blending them with fine limonite ores which have high adhering capabilities.CITATION:Zhu, D-Q, Li, X-B, Pan, J and Shi, B-J, 2015. Granulation behaviour of specularite fines in ferrous sinter mixtures, in Proceedings Iron Ore 2015, pp 91–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D R. Anstey

The mining of magnetite iron ore in Western Australia will generate large volumes of waste rock and tailings over many decades. The need to dispose of these materials will result in massive waste landforms that will require significant planning and management. The formation of comparable man-made landforms is relatively common, as exemplified through past practice in gold and iron ore (haematite) mining. Unfortunately, the performance of these landforms, with respect to long-term stability (erosion resistance), the release of low pH seepage water and aesthetic impact, has commonly been disappointing and environmental legacies have been created as a result. Lessons that have been learnt from past, large mining operations indicate that there is a need to rethink the methods of waste disposal and landform development applied to magnetite mining. The environmental compliance criteria applied to magnetite mines for the storage of tailings and waste typically include minimising dust generation (particularly as the tailings and mine waste may contain asbestiform minerals), control of silt, minimising visual intrusion and management of potentially acid forming materials. In addition, the climate of Western Australia and the paucity of both surface and groundwater in the vicinity of the magnetite mines frequently necessitate water consumption to be minimised. This paper discusses the potential to co-mingle magnetite mining waste streams in a variety of ways to concomitantly satisfy the environmental compliance criteria and the operational requirements of the mine. These methods include co-mingling of coarse tailings and waste through dry-stacking, deposition of tailings as a paste, co-disposing of all wastes to form an integrated landform and the co-mingling of all waste streams to produce PasteRockTM (a blend of tailings paste and crushed waste rock). The paper demonstrates how these techniques can be applied to the magnetite mining industry to provide better outcomes than might be achieved using more conventional techniques, currently employed in large-scale mining operations.

Jan 1, 2009

By N Gupta, R Trivedi, S Bhandari

Managing blasting operations in four mines surrounded by villages is a challenging task. This study aims to compare the blast-induced flyrock as observed in opencast mines by predicting flyrock distance using a soft computing approach known as an adaptive neuro-fuzzy inference system (ANFIS) and Flyrock Predictor software based on empirical studies. Blast design and geotechnical variables such as linear charge concentration, burden, stemming length, specific charge, unconfined compressive strength and rock quality designation were selected as independent variables, while flyrock distance was used as a dependent variable. Out of 120 blasts, data from 100 blasts was used to train and test the ANFIS model. Flyrock distance for the remaining 20 blasts was used to evaluate the model. Flyrock distance has also been predicted using Flyrock Predictor software based on an empirical approach using the same data sets as those used for ANFIS. Performance indices like root mean square error (RMSE), mean absolute error and coefficient of determination (R2) were evaluated to compare the reliability of ANFIS and Flyrock Predictor quantitatively. ANFIS was found to be a better predictive tool, with 1.75 m RMSE and 0.966 R2 compared to Flyrock Predictor, which returned RMSE and R2 values of 2.48 m and 0.932 respectively.CITATION:Trivedi, R, Singh, T N, Gupta, N and Bhandari, S, 2015. Soft computing approach to predict blast-induced flyrock, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 455–462 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The relative contents of Au in a series of groundwaters from water bores and exploration drillholes, located near Au mineralisation at Stawell, Ararat, Clunes and Ballarat in central Victoria, were found to be clear indicators of relative proximity to mineralisation in each region. In the same series, waters with anomalous concentrations of As distinguished Au mineralisation in bedrock from secondary palaeochannel or deep lead Au. In some groundwaters, acid pH values, high sulphate relative to other anions and detectable concentrations of reduced Fe reflected sulphide minerals associated with bedrock Au deposits. Close to some ore zones, locally anomalous groundwater concentrations of Mn reflected the Fe carbonates that accompany Au in these zones. In addition, elevated concentrations of other elements provided geochemical signatures for the aquifer lithologies associated with Au mineralisation. Of the lithological indicators Co and Ni, U and F, Rb and Cs, Mo and Li respectively reflected the mafic, felsic, potassic rich and quartz zones, principally in the Stawell mine area and to a lesser extent those at Clunes and Ballarat. Mineral stability diagrams, based on groundwater activities of K', Mgt and H`, demonstrated that a series of ore-zone groundwaters follow a trend that conforms with a biotite to sericite to kaolinite alteration sequence in aquifer mineralogy. This is a good illustration of how present day groundwaters under surface conditions can reflect the underlying mineral sequences that accompany these Au deposits. These observations around mine areas suggested that groundwater chemistry could provide a rapid and cost effective method of assessing prospectivity for An of extensive areas in central Victoria. To test this, regional sampling and analysis of 355 bore waters was carried out in a region where potential An bearing rocks are covered by Mesozoic and Cainozoic sediments and volcanics. Contoured elemental abundances and distribution from this program indicated five zones in which groundwaters had elevated Au and despite the cover, appeared to reflect variations in the underlying Palaeozoic rocks. Three of the Au zones could be in terrain affected by extensions or intersections of faults, a feature in common with the established Au deposits in central Victoria. Reflections of concealed Palaeozoic rocks included a possible zone of concealed Cambrian greenstones that coincides with three of the Au zones. It was concluded that each of the An zones represents a groundwater Au focus that warrants follow-up exploration.

Jan 1, 1997

By D Teyhan, J Kirsch

Traditionally, most Australian iron ore mining operations have been surface-based. Processing plants were designed to handle dry ores. In recent years mining operations in the Pilbara have progressively moved below the water table exposing wet, sticky ores which have caused lost efficiency in screening operations as particles tend to agglomerate and adhere, blinding screening media. Miners and vibrating screen manufacturers have experimented with a shift from linear motion to elliptical motion screens. Elliptical motion conveys and lifts particles. Effective on flat deck (horizontal and inclined) or sloping decks it can be configured to provide a controlled transport rate, applying pressure in all directions to maximise screening efficiency. In practice, elliptical motion screens have proven to be effective in dislodging sticky particles from screening media, reducing blinding rates and improving screen efficiency. Moisture and clay content change during the life of a mine. These changes are sometimes the effect of seasonal rainfall, in other cases due to increased groundwater and clay content as mining operations go deeper. To compensate for such changes and optimise screen efficiency, changing the ‘shape’ of elliptical screen motion is required. This has traditionally required shutting down processing plants and making mechanical screen adjustments. Plant downtime is costly and machine adjustment has been a ‘trial and error’ practice. This paper will explore the results of a field trial that is currently underway in Brazil of a next generation elliptical motion screen design that allows operators to make changes to exciter rotational direction, speed and screen stroke angle, through electronic drive phase control. The machine’s electronic drive system synchronisation is enhanced for stability with a unique mechanical timing system. Operating at up to 6 g, screen adjustments can be made on the fly without stopping production. Early trial results are showing up to 50 per cent improvement in screen efficiency compared with traditional elliptical motion machines under certain feed conditions.

Aug 24, 2022

By M I. Pownceby, A Torpy, C Johnson, N C. Wilson

To extract uranium from low-grade, calcrete-hosted uranium (CHU) ore is challenging owing to the presence of carbonate and swelling clay gangue minerals that require an alkaline lixiviant to be used. Western Australia possesses ~75 000 U3O8 t in CHU resources. Improvements to alkaline leach extraction practices would improve the economic potential of these deposits.A column leach study of CHU ore was run for 105 days using an alkaline carbonate-bicarbonate lixiviant. The uranium content of the liquor plateaued after 75 days at ~275 mg U/L; the calculated maximum solution capacity was 800 mg U/L. Spiked peaks and troughs were seen in the data set beyond the 60th day, where concentrations ranged from 220 - 290 mg U/L, indicating possible cyclic uptake and loss of uranium from the solution.Pristine and leached ore samples were geochemically analysed and mineralogically characterised at high resolution using a field emission gun-electron probe micro-analyser (FEG-EPMA). Results showed that leached ore samples from the top of the column contained less carnotite than pristine ore. In contrast, leached ore samples from the column base contained regions with more carnotite than pristine ore, indicating precipitation. Three carnotite grain micro-structures were identified in the leached ore; fan-spherulite, granular and core-shell cubes, with evidence for multiple growth phases.Evidence of carnotite precipitation was seen at the edge of and in pore spaces within montmorillonite and dolomite grains. The point of zero charge of both minerals is lower than the pH of the lixiviant (pH 10.8), thus the mineral surfaces are negatively charged and would not attract UO2(CO3)34- ions out of solution. Similarly, the decrease in the uranium content of the lixiviant is not attributed to super-saturation, as this was unlikely to have been achieved. Work is ongoing to understand the reason for carnotite precipitation and the fluctuations in the lixiviant uranium concentration that are seen.CITATION:Johnson, C, Pownceby, M I, Wilson, N C and Torpy, A, 2013. Microscale characterisation of pristine and processed ore - implications for leaching calcrete-hosted uranium ore, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 303-316 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By S Long, D Carnovale, L Louwrens

The Mt Wright underground mine (MTW) is located near the town of Ravenswood in north Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited.The Mt Wright mine has gone through many stages, from the conception and implementation of the world first ‘sub-level shrinkage’ stoping (SLS) with continuous fill mining method in 2010, through to steady state production. These have been outlined in detail in papers presented by Mackay (2011) and Mackay, Long and Koen (2014) at previous Underground Operators Conferences.Since the last paper was presented, MTW has experienced significant change in two key areas.The first significant change was the discovery of a previously unknown hazard in the form of flat rilling events (FREs) from closed drawpoints (DPs). These events are believed to be unique to MTW and pose a significant risk to both the safety of personnel and the business as a whole. The paper will discuss this hazard and the evolution of the controls and practices that have been introduced to mitigate the risk posed by the identified hazards. The material involved in these events is extremely dry, fine and hot.The second significant change is an altered stress regime bought on in part by a change in the production front orientation and a general deterioration in ground conditions in some areas of the mine. This has caused some production interruptions at MTW. The second half of the paper will describe the challenges encountered, the mechanisms behind these challenges and the strategies implemented to safely return MTW production to planned levels.It is believed that other operations can learn from the issues mentioned above, and the paper has been written with this in mind.`CITATION:Long, S, Carnovale, D and Louwrens, L, 2017. Mt Wright – managing unique risks, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 295–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By J Elder

Magnetic separation equipment has long been used to upgrade and beneficiate a wide variety of minerals and materials. Over the years, significant advances in both wet and dry magnetic separators have improved their operability and separation performances, broadening their use.But no one answer exists to the question: what is the right type of magnetic separator? For many minerals, including ilmenite, both process routes may be viable. There are technical, production, as well as economic reasons for choosing wet versus dry. However, recent developments illustrate that a new generation of wet magnetic separators is approaching performance once seen only in dry magnetic separation. With quality and production performance becoming similar, the choice between wet and dry magnetic separation is not as cut and dry as it once was.

Oct 5, 2011

By K P. Tully

In August 1996 a Microseismic Monitoring System developed by ISS International Limited was installed at the Pasminco Broken Hill Mine -Southern Cross area. The project aims were to:Assist in daily safety management in a mine environment which exhibits one of the highest occurrences of microseismic activity recorded in the Australian mining industry. Be used as a proactive tool in design of future development and stoping. The project to-date has been an unqualified success in achieving both goals. Consequently the system is being expanded from 6 to 14 monitoring sites.

Jan 1, 1998

By J H. Zietsman

The transition to more sustainable metal production is receiving much attention at present, and the iron and steel industry is at the centre of the conversation. New, more environmentally friendly production technologies, such as direct reduced iron (DRI) smelting furnaces, need to be developed in a short period of time. This necessitates increased use of computational modelling that incorporates more accurate material descriptions. The combination of large-scale multiphysics models of high-temperature processes with CALPHAD material descriptions leads to infeasible computation times. This can be resolved with the previously reported RapidThermo framework, which has been demonstrated to make equilibrium calculations orders of magnitude faster, within controllable limits of accuracy. In this paper, we explain how further material properties, which are important to modelling hightemperature reactors, can be added to the RapidThermo framework. This can improve the accuracy and usefulness of process and multiphysics models in the development of new technologies, which can significantly accelerate development cycles.

Aug 21, 2024

The optimisation and validation of shearer cutting methods is a time consuming engineering task. Many different parameters, of which not all can be controlled, can vary. The easiest solution, to increase the installed power and the longwall length, is not always the best. A different cutting method can increase the capacity without the need of new machines. The Department for Mining and Metallurgy Machinery at RWTH Aachen University therefore developed ProSL, the simulation tool for shearer and longwall operations. ProSL enables the engineer to create his own cutting methods and compare it with other methods. Machine-data can easily be varied to see the impact on the method. The research shows that sophisticated longwall methods increase the productivity of the system. The paper presents the results of the calculation with ProSL and shows how higher efficiency and lower costs can be achieved.

Dec 6, 2010