Search Documents

By S Gossmann, J Barlow, S Denner

"Unconventional gas resources, including coal seam gas (CSG) reservoirs, can be located above and below aquifers that provide groundwater for agricultural, industrial, urban and other uses. Development of these resources may, therefore, lead to potential impacts on groundwater supply.Management of reservoir/aquifer interconnections necessitates a program of focused data acquisition. For example, groundwater transfer from shallow aquifers to underlying CSG reservoirs may occur where CSG-containing units subcrop beneath shallow aquifers, possibly at significant distances from operating wells.Arrow Energy is undertaking studies of connectivity between aquifers including an investigation in collaboration with the Queensland Office of Groundwater Impact Assessment to evaluate connectivity between the Condamine Alluvium (CA) and CSG-containing Walloon Coal Measures (WCM).The Condamine Valley hosts highly productive agricultural land with groundwater resources heavily utilised for irrigation. Water demand outstrips available supply and groundwater has been subject to restrictions on further development since the early 1970s. Developments that could have an additional impact on groundwater resources in the CA are of major concern to local landholders. This paper describes: planned field investigations at two sites: 1. Stratheden, where pumping from the WCM will be undertaken 2. Daleglade, where pumping from the CA will occur how the data to be collected from field investigations will be used to refine predictions of flux between the CA and the WCM.CITATION:Denner, S, Gossmann, S and Barlow, J, 2013. Planned field investigation of connectivity between the Condamine Alluvium and Walloon Coal Measures, in Proceedings Water in Mining 2013, pp 91-98 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By Baker G

The detailed mineral composition of the lead-zinc ores at Captain's Flat was first studied in 1942 (Edwards, 1943).At that time the workings did not extend far below the 750ft. level. Since then development has been extended to the 1,390ft. level, and -at the request of the management of Lake George Mines Ltd., an examination of the ore from the deeper levels has been made as part of the research programme of the Mineragraphic Section of the Commonwealth Scientific and Industrial Research Organization.This account is. based on that examination (Mineragraphic Rept. No. ,537, C.S.I.R.O.)GENERAL GEOLOGYThe geology of the Lake George Mines has been described briefly in The Geology of Australian Ore Deposits (1953), and in much greater detail in an unpublished report by K. Glasson (1952). The area consists of fossiliferous Upper Ordovician sediments overlain by volcanics (Kohinoor VoJcanics), and by fossiliferous Silurian sediments. The volcanies comprise a series of· flows ranging in' composition from dacite to rhyolite, with interbedded tuft's and shale lenses.The region has been strongly folded. The regional strike is from 340° to 355°, and dips are from 75°W. to 75°E, A major syncline, pitching 200 N., occupies the centre of the area. The Kohinoor Volcanic'l outcrop as two bands which represent the east and west limbs of this syncline.The Volcanks in the western limb, with whIch the orebodies are associated, are more strongly sheared than those in the eastern limb.

Jan 1, 1953

By V Mutton, L Potts, D Joyce

This paper describes the method of extracting sill pillars within the underground operation from under unconsolidated mullock fill at the Cracow Gold Mine. This pillar recovery method was initially successfully used to recover sill pillars at Crusader Mine, Western Australia in 2001. Globally significant resources have been sterilised due to the placement of loose rock fill above crown pillars and within adjacent stopes. The method described here offers significant opportunities to increase recovery of sill pillar recoveries.The royal orebody sill pillars at Cracow Gold Mine form a significant resource. Extraction of these pillars needed to be undertaken with minimal ore dilution and maximum ore recovery. The application that was selected to consolidate the loose mullock fill above each pillar used an injection grouting process (Minova FB200).Cracow Gold Mine mining method is bottom up bench mining. The pillars were left within the orebody to allow for stoping to commence whilst the decline was being developed. Due to the remainder of the orebody being extracted the only access to consolidate the backfill was from the sill pillar extraction level. Numerous problems were encountered and overcome from product selection and trial, system of injection to extraction.This pillar recovery process achieved a 95 per cent recovery of the sill pillar compared with an estimated 60 per cent typical for other mining options.CITATION:Potts, L, Mutton, V and Joyce, D, 2012. Pillar recovery at Cracow gold mine using grouted consolidated mullock, in Proceedings Narrow Vein Mining 2012 , pp 179-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By N DavT

Pyritic tailings from the Quirke mine waste management area in Elliot Lake, Ontario were subjected to long-term column leaching experiments in two PVC columns measuring 122 cm in height and 15.2 cm in diameter. At the end of the leaching experiments, the columns were taken apart and sampled at 5 cm intervals for quantitative mineralogical and geochemical characterisation. Each column is represented by a total of ten samples. Polished sections, prepared from the samples, were studied by optical microscopy, scanning electron microscopy, electron microprobe and X-ray diffraction techniques. Mineral quantities were determined based on linear mixing models of whole rock and mineral compositions. Pyrite particle sizes were measured by image analysis interfaced to an electron microprobe. The tailings are coarse-grained (ie 96 per cent passing 75 ¦m) and composed of quartz, K-feldspar, muscovite and pyrite. Pyrite is homogenous and occurs as liberated particles displaying angular to subangular boundaries with strong dissolution features at the end of the leaching experiments. Based on up to 3518 particles measured in a sample, pyrite particle sizes range from 1.7 to 78.6 ¦m. Pyrite concentrations vary from 0.1 to 7.8 wt per cent, depending upon their location from the top of the columns. These correspond to pyrite losses of up to 99 per cent from their original level of 7.2 wt per cent in the upper half of the columns. Pyrite oxidation rates in terms of moles of pyrite oxidised per mole of pyrite per square metre per second were calculated from the effluent data and the measured pyrite particle sizes. The rates vary from 1.71+10-12 to 5.78+10-10 mole+m-2+s-1 within the 1.5 to 3.5 pH range for 10 ¦m particles. These results are comparable with the published oxidation rates at pH 2 where the dissolved oxygen is the only oxidant.

Jan 1, 2003

By G Zhao, S Hapugoda, E R. Ramanaidou, P Hapugoda, Y Jin, G O’Brien

In 2021 the ports of Port Hedland and Dampier in the Pilbara Region of Western Australia handled 900 Mt of iron ore. This ore was produced in the Hamersley’s mines and transported by trains to the ports for subsequent export. Dust, which is generally considered to be particles less than 100 μm in diameter, is generated at all steps in the supply chain. Whilst all dust may have potential impacts on human health and mangroves and buildings a proportion of the dust is classed as respirable (PM10) dust, which consists of particles <10 μm in diameter. In 2021, in response to the community concern with iron ore dust, CSIRO commissioned an internal study to characterise and benchmark the dustiness of the different ores and to develop targeted strategies to minimise dust impacts, without affecting other iron properties, such as stickiness during transportation. A specific concern is that that the dust in the PM10 fraction may contain significant amounts of particulates, such as free silicates which may have health implications for the workers and residents. This study provided detailed mineral and chemical characterisation of the dust generated from the railed fine ore products for five generic Australian ore types: Australian Channel iron Deposit (ACID), Australian Brockman (AB), Australian Marra Mamba (AMM), Australian Pilbara (AP) and Australian magnetite (AM). The dust from these fine ore products were compared to that generated from a sample of Brazilian Hematite (BH) type ore fines. The ores were evaluated for their physical, chemical and mineralogy properties, dust generating potential and understandings of the relationship between the dustiness of iron ores and their physiochemical properties. The size distributions of the railed fine ore products were determined and a suite of analyses were conducted on subsamples of total (-106 μm) and fine (-38 μm) dust. For all the ores, the total dust fraction contains less Fe and more contaminants (SiO2 and Al2O3) than did the bulk ore. The fine dust fraction contained even less Fe and more contaminants (SiO2 and Al2O3) than the total dust fraction. This suggests that the iron ore dust contains more clay and potentially free silica than does the bulk ore. These findings were supported by optical and Scanning electron microscopy analyses of the samples. Dustiness measurements were made for each of the different ores (-106 μm) to investigate the relationship of dustiness of various iron ores with their physiochemical properties and assess their responses to dust suppression by the application of water sprays.

Sep 18, 2023

By M Camarda, A Pirson, F Vasconcelos, J Mesquita

ArcelorMittal Prijedor is a goethitic iron ore mine located in the north-west of Bosnia and Herzegovina, which mainly supplies ArcelorMittal’s European subsidiaries. Annual production of the asset stands at the level of 1.5–2.1 million tons of iron ore product which is sent to ArcelorMittal Zenica steelmaking plant. Two types of products with approximately 50 per cent Fe are generated in Prijedor through a process composed by crushing, screening, and magnetic separation stages. Within this process one of the tailings produced is called ‘ultrafines’. The ‘ultrafines’ product corresponds to the desliming hydrocyclones overflow in Prijedor plant, which is classified in a size fraction below 25 μm and corresponds to about 5 per cent of feed. This material is richer in iron than the coarser size fractions of the ore but do not present a good performance in concentration processes. In this way, several studies have been carried out during the last years to find solutions to use the ‘ultrafines’ material without success. In this context, the possibility of dehydroxylate the goethite contained in the material transforming the mineral into hematite and thus increasing the iron grade of the final product was investigated. During the research, several dehydroxylation tests with different temperatures and time of exposure were performed. Using dihydroxylation process at temperatures higher than 800°C it was possible to produce a material with 43 per cent Fe from the original 39 per cent Fe ‘ultrafines’ sample. In addition, the dehydroxylation tests confirmed that goethite becomes completely transformed into hematite at 400°C (with an exposure time of 60 mins) and material is completely sintered at 1200°C. A simulation study based on dehydroxylation tests results showed that it would be possible to use a ‘ultrafines’ product with Fe grade higher than 45 per cent to produce a material with 50 per cent Fe through a complete dehydroxylation process.

Sep 18, 2023

By U König

The use of high speed detectors made X-ray diffraction (XRD) an important tool for quality and process control in the mining industries. Besides knowledge about the mineralogy of a sample it provides useful information in terms of quantification of the crystalline phases and the amorphous content. Cluster analysis of XRD data can facilitate multi-dimensional mapping of ore deposits and drill cores, identifying regions of favourable mineral compositions. The studies of this paper demonstrate how XRD and data clustering can be used for grade control, process optimisation and quality control of iron ores and iron ore sinters. These new developments have an enormous potential as an inexpensive, reliable tool, useful in the characterisation of iron and sinter materials implemented in an industrial environment.

Jul 11, 2011

By N Cusworth, W R. Mackenzie

"In 2007, the authors presented a framework for the conduct of resource project feasibility studies and provided guidance on minimum standards and best practice (Mackenzie and Cusworth, 2007).This paper will present the authors’ observations in relation to feasibility studies undertaken to support investments made during the unprecedented period of resource project capital investment since 2007. It will also provide comments on general trends in the mining industry’s approach to project assessment and update recommendations on best practice.CITATION:Mackenzie, W R and Cusworth, N, 2016. The use and abuse of feasibility studies – has anything changed?, in Proceedings Project Evaluation 2016, pp 133–148 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By H Weitz

Bateman Engineering provided process technology and engineering design to China Yunnan Metallurgical Company (CYMCO) for a 30 MW DC furnace for the production of high-grade titanium dioxide slag.Following the successful commissioning of the furnace during the latter part of 2009 and the first quarter of 2010, a period of adverse circumstances resulted in having to operate the furnace without feed and at a low power input for a period of time. When normal feed resumed, a layer of solid material was detected on the slag-iron interface during sounding measurements. The condition of the iron was also significantly altered. The iron temperature was much higher than the design value, but the carbon content had decreased to such an extent that a large amount of iron solidified in the furnace, which made iron tapping very challenging. The slag temperature was increased in order to melt the solidified iron. However, severe sidewall damage resulted, which finally led to a burn-through. A number of samples were taken from the slag that remained in the furnace. These samples were analysed to determine the chemistry and phase profile throughout the slag bath. The mechanisms of formation of the high melting-temperature phase on the slag-iron interface are discussed, as well as procedures that can be applied to prevent a recurrence of this phenomenon. Some recommendations are made for instances when furnace feeding is interrupted for an indeterminate period.

Oct 5, 2011

By M Singh, R C. Steinhaus, J J. Rust

Metallurgical process control systems in mineral plants often employ state-of-the-art monitoring analysers in an attempt to optimise plant operations and enhance mineral recoveries. These systems are unfortunately invariably fed by simplistic ‘sampling’ designs consisting of various in-stream methods or pressurised probes. These are unfortunate compromises and provide a false picture of what a mineral flotation or other process can achieve. The situation is further aggravated by some manufacturers using misleading marketing to suggest discrete cross-stream methods for metallurgical accounting and unreliable continuous in-stream off-takes for control sampling and that they are of synonymous integrity.Reliable, absolute or representative samples are often absent in many modern day concentrator plants, due to compromises around sample taking, particularly in terms of delineation and extraction errors and thus leading to sample bias. For more reliable information from online analysers we need a continuous, but much more reliable sample taken, than is current practice.Online analysers require a fully proportional and continuous supply of sample for effective process control, otherwise maximised or benchmark recoveries will be nothing but a pipe dream. Large discrete cross-stream samples from mechanically less reliable equipment cannot be used as feed to online analysers, as it will negatively impact real-time feedback and efficient process control.It is possible to build correct sampling systems that could do both process controls online and metallurgical accounting at the same time. Multotec Process Equipment (Pty) Limited, in close association with experienced sampling consultant Francis Pitard, have jointly patented a concept to achieve this and which is embodied in the design of the unique Rotating Cone® Sampler (International Patent Application No. PCT/IB2016/057464). This versatile unit for dry and wet applications has high division ratios via two-step sampling and division.A prototype was built and tested to validate the design and levels of precision achievable when employing the unit to split dry mineral fines or even certain foodstuffs.CITATION:Steinhaus, R C, Rust, J J and Singh, M, 2017. Does process control sampling always have to be a compromise?, in Proceedings Eighth World Conference on Sampling and Blending , pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Gill L. F, Gleeson HB

This paper describes the development of a Computer Aided Design and Drafting based mine planning system in the State Electricity Com- mission of Victoria. The system combines a commercially available CADD system with a commercially available mining/geological package. The methodology used in the establishment of the combined system, the fea- tures of the system and the current status of development are discussed.

Jan 1, 1989

By J T. Sharp, M A. Styler, D McGowan, P W. Mayne

Static liquefaction is a geotechnical hazard in mine tailings facilities. Soils that are contractive in shear are susceptible to static liquefaction. Tailings facilities are dynamic structures, typically growing in height each year. Dilative tailings may become contractive under increased effective stress. In this paper we show that Cone Penetration Test (CPT) data can be used to estimate the future state of in-place tailings under changes in effective stress. Susceptibility to static liquefaction is typically evaluated with the CPT by using a clean-sand equivalent normalized cone tip resistance (Qtn,cs) or by estimating the state parameter (?). An alternative approach is to evaluate the soil-state using the yield-stress-ratio (YSR = ?’y/?’v0). If the YSR equals one it is on the normal consolidation line and the soil-state is contractive. YSR values greater than three are typically dense of the critical state line (CSL) and the soil-state is dilative. In this paper we review how to calculate Qtn,cs, ?, and ?’y; and how the YSR can be used to screen for contractive soil behaviour. Unlike Qtn,cs and ?, it is very simple to estimate how the YSR will change due to an increase in overburden stress. This YSR approach was evaluated at three locations that saw increases in overburden of 10 m, 20 m, and 25 m. We show that the ?’y calculations are consistent and the increase in effective stress moves the soil state towards looser soil states. CITATION:Styler, M A, Mayne, P W, McGowan, D and Sharp, J T, 2018. Predicting changes in static liquefaction susceptibility using cone penetration test results, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 317–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

To enable ammonium nitrate-fuel oil (AN-FO) to be used on an equal weight basis with nitroglycerine explosives, smaller diameter bore holes became necessary with consequent modifications to drill steel and burden on holes. Detonation of AN-FO in small diameter holes proved successful both with and without primer charges but some alterations were required to adapt anoloders to the smaller holes.Important factors in training all operators in the new charging method were the retention of improved fragmentation, avoidance of excessive overbreak and keeping wall rock dilution to an absolute minimum. The successful storage of ammonium nitrate in climatic conditions with daily temperature fluctuations above and below the critical 90&#176;F has been achieved.INTRODUCTIONTechnical aspects of ammonium nitrate-fuel oil (AN-Fa) blasting agent are well covered in recent literature. This paper deals primarily with the manner of its introduction as the principal explosive underground at Great Boulder Gold Mines Ltd. and with the many problems encountered in the process. Following reasonably successful experimental firings in June 1962&apos;, using granular ammonium nitrate and an anoloder, permission was granted by theWestern Australian Mines Department to carry out test work in selected areas of the mine. The permit allowed for fuse firing only, and for a mixture of AN-Fa containing between 5t and 6 per cent fuel oil, with an adequate primer.The use of AN-Fa on an equal weight basis with nitroglycerine explosives, involved smaller diameter holes with alteration to ground burden and modification to drill steel.Initial tests indicated that it was apparent that AN-Fa could not replace gelignite on an equal weight basis if the...

Jan 1, 1965

By S Hawker, M Gibbs, A Craven

Current climate change projections suggest both an increase in the intensity of significant rainfall events and an increase in the variability of rainfall in some regions of Australia. It is necessary for mine site owners and operators to understand the effects that this potential shift in climate may have on their operations. The ability to maintain compliance with discharge regulations and operational security for those sites that rely on surface water run-off harvesting may be negatively impacted if some current climate change projections are realised. Although current regulations require the preparation of water management plans, these are generally developed using historical climate records for the site in question and as such do not give any indication of a siteÆs resilience to the influences of climate change.This study compares design and operational considerations for a case study mine site using historical rainfall records and modified records representing climate change projections. The future climate models are invariably broad scale and are limited in their capacity to be downscaled to a reasonable resolution for developing a site water balance. Instead the local historical data set has been modified to concentrate precipitation to peak periods and propagated through the model. The study looks at the siteÆs response to the potential changes in climate.It is shown that if current climate change projections are realised, this will have a significant effect on both the necessary size of designed surface water infrastructure and operational considerations on-site. A discussion is presented on the potential risks that climate change presents to mine sites and the range of options that could be considered to mitigate these risks. Depending on a number of factors, including location and risk profile of the owner/operator, resilience to climate change can be addressed as either a capital or operational expenditure (CAPEX/OPEX).CITATION:Craven, A, Hawker, S and Gibbs, M, 2013. Site water balance response to variable climatic conditions, in Proceedings Water in Mining 2013 , pp 211-216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By K L. C Gontalves

In 1999, the Mineral Development Centre of CVRD (CDM) acquired a flotation device referred to as Mini Pilot Plant (MPP), which is able to run continuous flotation tests with drill core samples. Since then this equipment has been used to define the flotation circuit and process conditions during the pre-feasibility phase of CVRDÆs copper sulfide projects. Until now, the MPP results had not been validated for an industrial flotation operation. The present work consists of a comparison and correlation of the results from a flotation MPP and an industrial plant. In order to make this comparison, an industrial plant was completely sampled and the feed ore was tested on bench scale and on a MPP. The metallurgical and mass balances of each test were used for the comparison.

Jan 1, 2005

By I Özen, G Chitumbura

A paper identifying anticipated challenges in the extraction of the N3500 Orebody at Glencore Xstrata Copper’s Mount Isa Copper Operations was written in 2007. The paper identified the depth of the deposit, the anticipated high stresses, talc alteration and issues with ground support as factors that may affect production. A number of strategies were planned to cope with these issues. After six years of extraction those strategies are evaluated and additional measures taken are outlined. Strategies to cope with the limited mine life are presented, and methods to overcome additional challenges encountered during production are described.CITATION:Chitumbura, G, Matthews, D, Özen, I and Jackson, S, 2014. One mile underground – mining the N3500 orebody at Mount Isa Mines, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 265–282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By M Ind, B Usher

Environmental regulators are increasingly adopting risk-based approaches to protect aquatic ecosystems. The Australian and New Zealand Environment and Conservation Council (ANZECC) and the Agriculture and Resource Management Council of Australia and New Zealand (ARMCANZ) (2000) introduced a risk-based approach to water quality guidelines that use decision frameworks to adapt water quality guidelines to local environmental conditions. Environmental quality objectives are no longer a simple ‘pass or fail’ number such as restricting total suspended solids (TSS) concentration to a specified limit for a particular rainfall event. This approach ignores spatial and temporal variability and the complexity of aquatic ecosystems. The risk-based approach establishes levels where adverse effects may occur. If these objectives are not met, further risk-based investigation is undertaken to assess the potential impact to the ecosystem. Klohn Crippen Berger (KCB) developed a dynamic simulation to predict the variability of sediment discharges, which is applicable for risk-based impact assessment of aquatic ecosystems. The application of the methodology over the life of a mine site is illustrated using a proposed South Pacific mine.The site location is in extremely rugged terrain with a high annual rainfall of approximately 4.7 m. There were two major sediment ponds proposed to reduce sediment discharges. A sediment and hydrology model was developed in Goldsim to provide daily estimates of run-off flows and sediment concentrations. A modified algorithm based on the Australian water balance model was created and incorporated into the Goldsim model and calibrated using recorded field data.The sediment module was developed based on a Revised Universal Soil Loss Equation (RUSLE) assessment, an annual prediction of soil loss over a catchment. A land-use type erosion vector was developed for different land-use types and for each of the subcatchments, a subcatchment erodibility vector was calculated. This vector and the daily rainfall erosivity factor were used to estimate the daily soil loss. The estimated soil loss and the modelled run-off yielded predictions of daily sediment concentrations. Finally, a sediment settling module was used to predict the daily efficiency of the sediment ponds and hence discharged sediment concentrations.The results of this modelling form the first part of a quantitative risk-based assessment into suspended solids impacts. The second part is the assessment of the effects of these predicted TSS concentrations on aquatic ecology. As part of the feedback-loop required in a risk management framework, if the environmental quality objectives are not met then further management decisions and actions may be required to reduce the risks presented by suspended solids. This may include modifications to: the mine-development plan; construction techniques and scheduling; processing techniques; rehabilitation strategies; or hard-engineering solutions such as sediment basins or flocculation.The Goldsim water-balance model provides a quick and efficient method of testing potential remedial actions on predicted sediment loads and concentrations. In combination with a cost-benefit assessment, options for reducing sediment releases from the mine site can be effectively and quantitatively compared thereby providing mine operators with a basis for decision-making. Regulators can also be satisfied that potential impacts to aquatic ecology have been comprehensively assessed and the necessary management decisions have been initiated to limit risk to the environment.CITATION:Ind, M and Usher, B, ?2014. A dynamic sediment simulation to predict the variability of suspended solids concentrations over life-of-mine for application to a risk-based environmental assessment, in Proceedings Life-of-Mine 2014 , pp 191–204 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By R Beaulieu, D Burlingame, C Hanks

The Ekati Diamond MineÖ is CanadaÆs first diamond mine and is located 300 kilometres northeast of Yellowknife in the Northwest Territories. The development of the mine supports sustainable development through the integration of environmental, economic and social considerations with the broad aim of minimising environmental impacts while maximising opportunities and benefits to northern residents and northern businesses. The environmental assessment and regulatory processes for the Ekati Diamond MineÖ were the most extensive seen in the NWT to that date; in Canada only uranium mines receive more attention. In addition to the regulatory requirements, an Environmental Agreement was negotiated with the Governments of Canada and the Northwest Territories to address environmental concerns not covered by existing legislation and regulation. Under the agreement an Independent Environmental Monitoring Agency was set up to oversee the regulatory process and implementation of the Environmental Agreement. Environmental stewardship is implemented through an Operational Environmental Management Plan, part of which includes effects monitoring programs for wildlife and aquatics where available traditional ecological and scientific knowledge are integrated to broaden our understanding of the tundra environment. A Socio-economic Agreement was concluded with the Government of the Northwest Territories to maximise employment and business benefits to the north. Voluntary and confidential Impact Benefits Agreements (IBAs) were also negotiated with four Aboriginal groups who use the area where the mine is located. The intention of the IBAs is to foster development initiatives and a partnership thereby helping to insure that benefits from the project flowed to the Aboriginal groups despite a lack of settled land claims in the region. All these were completed before commercial production in October 1998. Employment targets of 62 per cent residents of the Northwest Territories and 31 per cent Northern Aboriginal have consistently been met thereby ensuring benefits flow to residents of the Northwest Territories. In 2000, $316 million was spent to support operations at the Ekati Diamond MineÖ. Of this, 82.2 per cent of total spending and 26.6 per cent total northern spending was northern and northern Aboriginal businesses, respectively. The environmental and socio-economic monitoring results are reported annually to the responsible government agencies and potentially affected Aboriginal groups. To date, there have not been any significant adverse environmental effects documented and socio-economic targets have been met.

Jan 1, 2002

By S Barrow, D Kent

Controlling the access of equipment, and people, has become more critical over the last few years for improving productivity and to meet safety responsibilities imposed by legislated obligations to have safety management systems. Hence Mine Site Technologies (MST) has spent the last three years completing the development of the tagging system to meet the mining industryÆs requirements, particularly streamlining access control. The basic tagging system tracks active Tags carried by personnel, or attached to vehicles and equipment, within underground zones. These Tags are detected (read) by Beacons placed strategically throughout the mine. As a Tag, or Tags, go past a Beacon they are read and the information transmitted back to the main database PC. This allows the current whereabouts of personnel and equipment to be known, as well as the history of their movements. The objectives of implementing the TRACKER Tagging System at Oaky No 1 Coal Mine were to: maintain a count of personnel inbye a particular point, and can alarm when a pre-set number is reached (eg the limit imposed by availability of SCSRÆs, etc); maintain a count of vehicles (and vehicle type) inbye a point, and can alarm if when a pre-set number is reached (eg when rated diesel units exceeds the limit for the ventilation present in that zone); manage the vehicle fleet, by keeping track of various vehicles underground better control and dispatch management of the equipment is achieved; keep track of equipment, knowing the location of equipment (such as forks, baskets, pumps, fans, etc) where last used or stored will minimise the risk of losing gear and assist in keeping inventory to a minimum; and locate personnel in emergency situations, by placing read Beacons throughout the mine the location of all personnel can be known in real time so that in the event of an emergency, their withdrawal can be monitored.

Jan 1, 2005

By J D. Grobler

In the heavy minerals industry wet high intensity magnetic separators (WHIMS) are widely applied for primary magnetic separation of magnetic minerals and non-magnetic minerals. This piece of equipment is well known for its robustness to handle a wide range of feed conditions and still produce stable product qualities and yields. A heavy mineral production plant aimed to increase production through their WHIMS plant containing 11 duties and 26 units. Instead of adding new units an alternative approach was followed to firstly maximise the efficiency of the current circuit and secondly to consider possible reconfiguration of the circuit to produce additional product tons for minimal capital investment. In order to characterise the current circuit’s efficiency, identify pockets of excellence and determine the areas for improvement the whole circuit was surveyed several times and mineral mass balances were drawn up.This paper aims to: discuss the modelling process of the WHIMS circuit,explain the calibration and validation process followed to ensure the accuracy, anddemonstrate the sensitivity analysis performed on the different options. From this analysis an efficiency criteria was developed to compare different circuit configurations that enabled the production plant personnel to make an informed decision on the way forward.

Oct 5, 2011