Search Documents

By D. J. Reed

Concord coal mine near Bessemer, Ala., built, owned, and operated by Tennessee Coal & Iron Div., U. S. Steel Corp., produces only a metallurgical grade for use as coke in blast furnaces of the division at the Fairfield and Ensley works. Capacity of the operation is approximately 800 tph, half of which is delivered to the coke and coal chemical plant at Fairfield after beneficiation to metallurgical grade coal. The remaining portion of the mine run is rock and refuse removed during preparation. Concord mine coal is hoisted to the surface coal preparation plant by an underground slope conveyor. The slope conveyor is 2449 ft long and has a lift of 729 ft. At time of installation the Concord mine slope conveyor was the largest single conveyor unit ever made with respect to belt horsepower and total lift. After several years it became necessary to determine the cause of slope conveyor cover wear.

Nov 1, 1956

By John C. Cook

Long-wave short-pulse radar has been shown capable of exploring to distances of several hundred feet through massive, dry rock salt. Exploration distances of 30 to 60 ft through bituminous coal and massive limestone, respectively, have also been demonstrated with low-power experimental radar equipment in underground mines. Working ranges up to 250 ft in limestone and coal are considered feasible. Radar reflections should be produced by all large electrically contrasting objects such as fault gouge masses, wet shattered ground, metallic mineralization, adjacent mine workings (dry or flooded), and abandoned drill holes. It is believed that radar can locate such obstacles in advance of underground mining through all massive rocks of low free-water content, including many igneous and metamorphic rocks. Three years of studies and experiments in radar exploration through rocks are reported.

Jan 1, 1974

By Lancaster Jones

The gravity magnitudes obtained by means of observations with the Eötvös balance in the field are necessarily resultant or total effects due to all abnormalities of mass distribution, including even the effects due to the ellipticity and rotational motion of the whole earth. Since the object of the survey is to isolate the effects which arise solely from some particular subterranean feature, and to deduce therefrom the configuration and extent of this feature, the first step is to eliminate from the observed effects all those due to "disturbing" (i. e., unwanted) features, whether above or below the surface of the ground. The disturbing features have different characteristics, according to their situation relative to the center of the balance and to the horizontal plane through the foot of the balance, or station point; this diversity was recognized by Eotvos, who divided the total effects into so-called Normal, Terrain, Topographical, Cartographical and Subterranean effects. This classification has been adhered to by most subsequent investigators, but the writer prefers to employ the term "three-dimensional," which really indicates the essential character of the class of effect known as "Subterranean," at any rate from the standpoint of the computer of effects. Before disturbing effects can be eliminated, the features must be measured up or surveyed, whether by topographical, mining, or boring methods, and then the effects of each feature calculated and subtracted from the total observed effects. After this the problem of interpreting the residual effects will itself necessitate the computation of the assumed feature, or even a series of trial features. The task of computing gravity effects is therefore of great importance. In the early work, by Eötvös himself, the computation practically ceased when the terrain and topographical effects had been calculated, but later surveys have demanded an ever-increasing extension in the technique of computation. Certainly in surveys designed to locate minerals, particularly ores, the calculations have to be extended far beyond those of Eötvös, while his methods of computing both terrain

Jan 1, 1929

By Paul D. Merica

Jan 1, 1937

By M. L. Bleiberg, L. J. Jones

THE changes induced in metals by subjecting them to heavy particle bombardment have received widespread attention in recent years and results of such investigations have been reviewed by Slater, Dienes, Seitz, Siegel, and Seitz and Koehler.1-5 Of particular significance are the property changes that occur in uranium-base alloys due to neutron bombardment. These changes are generally very severe since fission occurs within the sample, resulting in the formation of heavy, highly energetic fission fragments, as well as additional neutrons born in fission, which serve to intensify the damage generally associated with fast neutron bombardment of nonfissionable metals. The property changes in uranium and uranium alloys due to neutron bombardment have been summarized by Paine and Kitte16 and Billington.7 It has also been shown that neutron bombardment of

Jan 1, 1959

By I. A. Lesk

The various materials utilized in the construction of integrated circuits, and the resultant materials interfaces, are discussed with emphasis on a materials system that is compatible with all types of integrated circuits and minimizes the number of different interfaces. Problems with interfaces may originate in the silicon, on its surface, and between other materials within the integrated-circuit package independent of the silicon. ThE difference between integrated-circuit theory and practice may generally be spelled out in terms of the difficulties in fabricating a desired structure. There are, of course, problems in forming the requisite materials, of the necessary composition and geometry, where needed. A distinct class of problem, however, is associated with interfaces— generally between different materials, but occasionally between regions of the same material. We require that each interfacial system perform its proper electrical, mechanical, and thermal function, and do so in an unchanging manner with time under the most severe operating conditions. In a practical sense, we deal in nonideal systems, such that it is generally not possible to form an interface exactly the way it was intended, even if we allow for a knowledge of the practical limitations of the fabrication system. Another way of looking at this situation is to realize that, when we form a group of interfaces under apparently the same experimental conditions, there are often differences of important consequence between them. Very high-magnification pictures, such as are obtained by an electron microscope, reveal fine structure that often differs over the area of a given sample, as well as from sample to sample. Low-magnification pictures look better, but don't eliminate the problem. The trend towards integrated circuits, and away from circuits fabricated utilizing separate components, is very strong in many areas of electronics. A typical silicon monolithic integrated circuit, still in place in the wafer on which it was fabricated, is shown in Fig. 1. The increased reliability which is being experienced through the use of integrated circuits can, to a large extent, be credited to the reduced complexity of the interface system that is present in the electronic system. A glance at Fig. 1, however, with all of its epitaxial and diffused p-n junctions, and interconnect system, shows that interfaces have been far from eliminated. Fig. 2, depicting a schematic cross-sectional view of a (partial) typical integrated circuit, illustrates in detail the numerous interfaces that occur in this type of structure. Besides the individual circuit elements, there are interfaces for isolation, and, Fig. 3, even a crossover requires a series of interfaces. What has been accomplished, however, irrespective of whether or not the total number of interfaces in the circuit is increased or decreased, is that the variety of interfaces is very much reduced. This is because there are fewer materials involved. Since the expense incurred in an R & D program to improve reliability is pretty much directly proportional to the variety of interfaces involved, it is economically advisable to work with integrated circuits for highest reliability. That is not to say that circuits built using standard components could not be made as reliable as integrated circuits, but that the expense involved because of the more complex over-all interface system would be much greater. Although electronic performance utilizing integrated circuits with all silicon elements (i.e., transistors, diodes, resistors, capacitors) is adequate for many applications, there are numerous instances where thin-film passive elements must

Jan 1, 1965

By G. E. Keller, G. D. Coe

Several methods have been devised for rapid determination of sulfur in coal using a high-temperature combustion furnace. The fundamental principles of the various methods are similar but the techniques vary widely. The method described herein is no different in principle from some of its predecessors but varies considerably in technique. Originally devised to overcome the low-accuracy criticism leveled against the others, the tube-furnace method has proved successful for limited applications. Work is being done to widen the applicability of the technique. Subsequent to the work of A. Vita1 in 1920, a number of investigators have published data dealing with the rapid determination of sulfur in coal using a high-temperature combustion furnace.2-5 These, together with several unpublished methods, involve wide differences in technique although they are all similar in principle. Investigation of typical details of procedure showed that poor precision or accuracy could be attributed to one or more of the following: 1) inadequate quantity of sample to be representative, 2) a delivery tube temperature too low to confine condensation to a washable area of the tube, 3) no provision for back washing the delivery tube, 4) incomplete absorption of the sulfur compounds due to inadequate bubbler, and 5) the false assumption that all of the sulfur is evolved as sulfur dixoide. The method herein discussed is no different in principle from some of its predecessors; the differences are in technique. Although the method is rapid—a determination can be completed in 5 min— accuracy has riot been sacrificed in order to achieve speed. MATERIALS AND EXPERIMENTAL WORK Fig. 1 shows the arrangement of the equipment. A metered volume of oxygen is passed through calcium chloride for removal of moisture, then through Ascarite for removal of carbon dioxide, and thence through a glass tee to the feed end of the combustion tube. Connected to the side arm of the glass tee is a rubber tube that is closed with a pinch clamp during combustion of a sample. The products of combustion are expelled through a Vycor bubbler, the end of which is submerged 3 cm below the surface of a 1 pct hydrogen peroxide solution contained in a 300 ml high-form beaker. At the completion of the 4-min combustion period the contents of the beaker are titrated to a yellow end point, using a methyl red indicator, with 0.05 N sodium hydroxide (or sodium tetraborate). The pinch clamp on the tube leading from the tee in the oxygen line is then opened and mouth suction applied to draw the hydrogen peroxide up into the bubbler past the ell, almost to the rubber tube connecting the bubbler to the combustion tube. This washing of the bubbler is repeated until no further acid reaction with the indicator is obtained. The hydrogen peroxide-sul-furic acid solution is then titrated to the final yellow end point. Test work conducted at the Robena Laboratory disclosed the following critical conditions that had important bearing on the precision of the method: Weight of Sample: Several series of tests wherein the sample weight ranged from 0.1 to 0.5 g of -60 mesh coal showed that the lowest variance (standard deviation squared) resulted from the use of 0.5-g samples; the variance was slightly greater when 0.3-g samples were used, and with less than a 0.3-g sample weight the variance increased rapidly with decrease in weight. Although the use of a 0.5-g sample invariably resulted in a very slight explosion as soon as the sample entered the hot zone of the combustion tube, this did not detract from the precision of the method. Temperatures: Mott and Wilkinson5 found that a combination of low temperature (1250°C) and low oxygen flow rate (less than 700 ml per min) tended to give high results due to formation of oxides of nitrogen. Although the method herein employs a much higher oxygen rate than 700 ml per min, as an additional precaution to assure accurate results, 1315°C (2400° F) is recommended as the most desirable furnace temperature. The temperature of the elbow of the bubbler should be at least 75°C to minimize condensation

Jan 1, 1961

By Ancel St. John

Defects in the interior of metal objects are troublesome to both manufacturer and user. For the former, they frequently increase manufacturing cost through the rejection of material when defects appear after considerable work has been done. For the latter, they often cause damage to equipment, personal injury, or loss of life when a part, which has passed all inspections and has been put in service, gives way because of a hidden flaw. Methods of testing that locate such flaws without subjecting the specimen to possible, if not actual, destl-uction are few; x-ray examination, whether fluoroscopic or radiographic, is one. Hitherto, however, x-ray examination has been restricted to objects of nearly uniform thickness and regular outline; the inspection of such articles as those shown in Fig. 1 has been inconvenient and unsatisfactory. This figure represents a group of 5/16-in. hexagonal-head machine bolts,

Jan 1, 1923

By Ancel St. John

Defects in the interior of metal objects are troublesome to both manufacturer and user. For the former, they frequently increase manufacturing cost through the rejection of material when defects appear after considerable work has been done. For the latter, they often cause damage to equipment, personal injury, or loss of life when a part, which has passed all inspections and has been put in service, gives way because of a hidden flaw. Methods of testing that locate such flaws without subjecting the specimen to possible, if not actual, destl-uction are few; x-ray examination, whether fluoroscopic or radiographic, is one. Hitherto, however, x-ray examination has been restricted to objects of nearly uniform thickness and regular outline; the inspection of such articles as those shown in Fig. 1 has been inconvenient and unsatisfactory. This figure represents a group of 5/16-in. hexagonal-head machine bolts,

Jan 1, 1923

Jan 1, 1905

By Edwin Ludlow

For many years, coal has been known to exist in the valley of the Sabinas river, in the State of Coahuila, and for about 15 years it has been worked by the Mexican International Railway Co., which opened mines for its own fuel-supply when the railway was built, and has been mining continuously ever since. The coal-basin worked by this company lies along the Sabinas river, principally on the SW. side. It covers a wide area and has been carefully prospected, but only in a few parts have the beds been found sufficiently thick and regular for economical operation. This Sabinas basin was considered the only one in this field, until, in the Spring of 1899, the Las Esperanzas basin was found by Messrs. J. L. Elliot and E. D. Peters, who were in Mexico looking after some copper-properties. After a further examination by Mr. James T. Gardiner, of New York, the Mexican Coal & Coke Co. was organized in June, and active work was begun on Nov. 5, 1899. The coal-field of Las Esperanzas, situated in the State of Coahuila, about 85 miles SW. of Eagle Pass, Texas, adjoins and runs parallel with the Sabinas basin—an anticlinal separating the two outcrops by about 2 miles. Fig. 1 is a sketch-map of a part of the basin. The coal-formation is in the Upper Cretaceous, and corresponds with the Laramie measures of the United States. The following geological section, taken in Nogales canon, shows the measures between the massive limestones forming the Sierra de la Santa Rosa and the outcrop of the coal: Section. Feet. Limestone,...Unknown. Blue shale,.........110 Shale and sandstone,.. 60 Bed of fossiliferous shale,. 60

Jan 1, 1902

By E. Miller, J. M. Eldridge, K. L. Komarek

Activities of magnesium in liquid Mg-Sn alloys have been determined between 5 and 90 at. pct Sn and 990" and 1290°K by an improved isopiestic method wherein tin specimens, heated in a temperature gradient and contained in crucibles of special geometry, were equilibrated with magnesium vapor in a closed titanium system. The crucibles were designed so that the equilibrium compositions of the specimens were satisfactorily preserved on termination of the experimental runs by quenching. The activity values are in excellent agreement with those predicated on the phase diagram and allowed a delineation of the solidus curve of the compound Mg2Sn near its melting point. EQUATIONS have been recently derived relating the chemical potentials of the components to the liquidus and enthalpy data for binary systems exhibiting one congruently melting compound.' The liquidus curve of the Mg-Sn system between the eutectics was carefully redetermined and the thermodynamic properties thus calculated were in reasonably good agreement with values derived from electromotive-force measurements of an,' but differed greatly from the iso-piestically determined values of Ashtakala and Pid-geon.3 The present study was initiated: a) to resolve the discrepancies; b) to develop a method for measuring activities in systems having volatile (and possibly highly reactive) components; and c) to use the method in a general investigation of the thermodynamic properties of the homologous series of Mg-Group IVb systems, i.e., Mg-Pb, Mg-Sn, Mg-Ge, and Mg-Si. This paper describes the results for the Mg-Sn system. An isopiestic technique, originally developed by Herasymenko 4 and adapted for alloys having a component of high reactivity and low volatility,5-8 was modified in this study by using crucibles designed to preserve the equilibrium composition of highly volatile liquid specimens on quenching from high temperatures. Tin specimens, contained in tightly covered graphite crucibles and heated in a temperature gradient, were equilibrated with magnesium vapor of fixed pressure from a magnesium reservoir kept at constant temperature in a previously evacuated and sealed titanium tube. During equilibration magne-

Jan 1, 1967

By J. Stuart Warner

The reaction COSO4(c)?CoO(c) + So3(g)was investigated from 950° to 1170OK by two different methods. The sulfate was decomposed in a previously evacuated space and Pso3 calculated from the measured total pressure on the assumption that Pso2 = 2P02. The sulfate was also decomposed under conditions of controlled oxygen pressure. The difference in the results obtained by these experimental techniques is attributed to the effects of thermal diffusion. The standard free energy change for the reaction is given by ?F° = 66,292 + 17.273T log T — 102.57 T (±300 cal/mole). It was found by DTA and X-ray diffraction studies that CoS04 undergoes a transformation at 617°± 4°C. THE metal sulfates may decompose directly to the oxide or pass through one or more intermediate basic sulfates. Provided the oxidation state of the cation does not change in the course of the reaction, the decompositions may be described in general as follows: One of the major objectives of this work was to determine the validity of Eq. [3] as much of the existing sulfate data has been calculated from decomposition pressures by Eq. [5]. The type of apparatus generally used for these measurements consists of a reaction vessel at high temperature which communicates with a manometer at room temperature. A temperature gradient is thus imposed on the gas phase causing thermal diffusion which brings about a partial separation of the different gaseous species present in an initially uniform mixture. The basic theory and experimental facts associated with this phenomenon are summarized elsewhere1 and it will suffice to state here that the heavier gaseous species diffuses down the temperature gradient. Since thermal diffusion destroys the homogeneity of the gas phase, it is not necessarily true that Pso2 = 2Po2 in any particular volume element of the gas phase even though there are twice as many molecules of SO, as of 0, in the gas phase considered as a whole. Under these conditions, the decomposing sulfate gives off SO, which dissociates to SO, and 0, and all three species are distributed throughout the system by thermal diffusion. However, the sulfate will continue to dissociate until the equilibrium value of PSo3 is established on the hot zone. Thermal diffusion may distribute SO2 and O2 throughout the gas phase in any way so long as Eq. [2b] is satisfied in the hot zone; i.e. Pso2(Po2)1/2=K3pso3. When a steady state is reached, we can characterize Pso2 in that

Jan 1, 1962

By William H. Morris

At the Glen Summit meeting, the question of controlling the silicon in pig-iron WAS raised; and as this has been deemed by most furnace-men for years past a matter of special difficulty, an account of our experience in the matter may be of interest. When running on mill-iron, some years ago, we aimed to keep

Jan 1, 1893

By O. C. Holbrook, George G. Bernard

A new theoretical treatment has been obtained for the behavior of pattern waterflood injection wells when closed in. Two cases are treated: Case I where oil and water are assumed to have the same properties, and Case 2 where they arc different. In applying the method, one plots log (p — p,) vs closed-in time, where p is well-bore pressure at any tims and p, is static pressure. The value of p. is determined by trial and error as that value which makes the plot linear at large time. A value for the permeability-thickness product can be determined from the intercept of this linear part, and a value of the skin factor from the injection pressure at time of closing in. Application of the method to data from water floods at three fields seems to give reasonable results. For the case of unit mobility ratio, it is proved that this new method should give the same value for permeability-thickness product as the conventional pressure build-up method. In addition, the new method gives correct values for static pressure, whereas the conventional method does not, often indicating negative static pressures. The new method may be used in cases where the surface pressure persists after closing in as well as in cases where it does not. INTRODUCTION It is of considerable interest and importance to be able to determine the characteristics of the reservoir in an area surrounding a water injection well. Thus, if we can determine early in the life of an injection well that there is a considerable "skin effect", remedial measures can be started before a full-scale pattern flood begins. Similarly, if it can be shown that a gradual buildup of skin effect is occurring with time, measures to free the water of plugging material can be taken. Determination of static pressure in the water-injection well may show that the water is entering a thief zone and not the desired reservoir. Finally, determination of the permeability of the sand around the injection well will allow estimation of the future relation between injection pressure and rate. It should be possible to determine average reservoir permeability, skin effect and static pressure from pressure fall-off data. However, at the time we began work on this subject, it was thought that no adequate theory on which to base such determinations' was available. According to the conventional method which considers the reservoir to be filled with one fluid of small compressibility (see Van Everdingen, Joers2, and Nowak2), shut-in pressure is plotted vs log where is injection time, and At is closed-in time. The physical significance of injection time, may well be questioned in this case, since in a reservoir completely filled with a single fluid (as required by this theory) and with input and output rates equal, the pressure behavior after an initial transient is independent of t,. Attempts by our Tulsa area to use this theory led to negative values of static pressure in most cases. Because of these limitations of the method discussed above, it was decided to attempt to develop a new theory of pressure behavior in water injection wells, one which would apply when there is a gas saturation, as is so often the case in water floods. In the following treatment the assumptions and basic equations are given first, then the method of application of the equations. A complete example is given to clarify details of application. All difficult mathematics has been placed in the appendices so that the reader can follow the text without difficulty. However, if he wishes only to apply the results without knowing the basis for them, he can learn how to do this from reading only the sections entitled "Plotting of Experimental Results" and "Example." ASSUMPTIONS AND BASIC EQUATIONS Statement of Problem It will be assumed that a horizontal layer of constant thickness contains in its pore system a mixture of oil, gas and water. While water is being injected into this pore- system through a well at constant rate, an oil bank is built up, gas being expelled from the space taken by the oil as shown in Fig. 1. The saturations within each

By E. C. Barfield, D. G. McCarty

Two-dimensional analyses offer considerable promise in providing the basic information required to effect more precise control of petroleum reservoir performance. This paper describes a method for conducting some engineering analyses of this type using a high-qreed digital computer. The general approach is to (I) develop a representative numerical model of the reservoir and (2) employ a suitable numerical technique to solve the basic equation of flow and to develop the required engineering information for the particular case represented by the model. This technique has been used to calculate pattern performance in connection with several field projects involving water injection into oil reservoirs. This type of analysis involves sequentially (I) calculating the pres-' sure distribution in the reservoir and (2) tracking the progress of the interface between the displaced and displacing fluids in a step-wise manner to provide a depletion history of the operation. The particular analysis presented in this discussion is subject to the restriction that the mobility of the displaced and displacing fluids be equal and assumes that the fluids are incompressible and that gravity and capillary pressure do not affect the shape of the flood pattern. Complete two-dimensional .flexibility is maintained with regard to definition of reservoir rock and fluid characteristics, placement of physical restrains and boundary conditions, investigation of flow characteristics in the reservoir, and movement of the displaced and displacing fluid interface. The results of these studies indicate that the highspeed digital computer is well suited for conducting reservoir performance studies in two-space dimensions and that dependable numerical techniques are available for making such analyses. INTRODUCTION One of the problems facing petroleum engineers is that of providing more precise engineering control over reservoir operations at all stages during the depletion cycle. The most direct approach to this problem is to simulate the reservoir with some type of physical or mathematical model and use the information developed from the behavior of the prototype to predict the performance of the actual reservoir. This principle is, of course, not new, and a variety of simulation techniques have been developed to provide information on the behavior of oil and gas reservoirs. One straightforward refinement of present reservoir analysis techniques is the progress from one-dimensional reservoir models to those where the reservoir can be represented in two- and three-space dimensions. Multidimensional reservoir analyses are desired in order to show not only what is happening in the reservoir but in addition to show where in the reservoir the various phenomena of interest are occurring. Thus far, two-dimensional analyses have been confined predominantly to potentiometric and electrolytic model studies. However, when large numbers of wells are involved and where large-scale models are required, such problems become very tedious and instrumentation problems become acute." It is possible through use of numerical methods and general purpose digital computers to avoid many of the instrumentation difficulties and to relax some of the restrictions of previous techniques. The purpose of this paper is to discuss some recent experiences with the use of high-speed digital computers for predicting pattern performance in fluid injection operations and to describe the numerical procedures which have been used for making such analyses. THE NUMERICAL MODEL The problem of representing the reservoir with an appropriate numerical model is composed of at least two important considerations. The first requires that an adequate description of the reservoir mechanism be formulated in the form of the basic differential equation describing the process. The second consideration is definition of the physical characteristics of the reservoir. The latter requires that representative basic data be obtained, examined, and interpreted to provide sufficient detailed definition of the pertinent physical properties throughout the system. The Differential Equation One of the basic assumptions made for the purpose of performing the two-dimensional studies being dis-

By C. P. Miller

In order to determine the usefulness of geochemical and biogeochemical prospecting for nickel, ten localities representing several types of nickel occurrences were selected as sites from which to collect plant and soil samples. This report covers the investigations in two of the areas. After a brief geologic description of the areas, the author presents details of the experimental tests and resulting data. Conclusions drawn from the studies led to several general guides for further prospecting. In a study of the usefulness of geochemical and biogeochemical prospecting for nickel made about three years ago, approximately ten localities, representing several different types of nickel occurrences, were sampled and about 1500 samples of plant and soil were collected. This report will cover briefly the data and results for two areas, and a summary of guides for prospecting. DESCRIPTION OF AREAS SAMPLED One locality is the Red Flats nickel prospect in Curry County, Ore., about six miles southeast of Goldbeach, and the other is the Little Rocky Creek prospect in Stillwater County, southcentral Montana, just southeast of the Benbow chromite mine. The Oregon area is a lateritic-type nickel deposit formed on a nickel-rich serpentinite peridotite complex, similar to the Josephine intrusion in southwestern Oregon. The Montana area is a nickel prospect in norite, peridotite, and related rocks of the Stillwater igneous complex. The Stillwater complex is a series of layered basic and ultrabasic rocks, with a layer of norite-gabbro at the base and a series of peridotites and gabbros above. The nickel in the Oregon deposit occurs in both the peridotite and the overlying soil. A deep lateritic soil is developed locally on the peridotite and serpentinite and constitutes the ore. The average nickel content of the lateritic soil is less than 1 pct, whereas the nickel content of the weathered peridotite is about 1 to 1.5 pct. The nickel occurs as garnierite (Mg, Fe, Ni, Mn)3 (OH)4 (SiA1)2O5 in the soil and in the olivine and pyroxene in the peridotite where it probably substitutes for Fe2+ or Mg2+ in the silicate lattices. Nickel is found in three distinct ways in the Still-water rocks: 1) it is in the olivine and pyroxene minerals in norite, harzburgite, etc.; 2) it occurs as widely disseminated grains of pentlandite-pyr-rhotite, which tend to be concentrated in the lower norite band; and 3) it occurs as discrete bodies of pentlandite-pyrrhotite and chalcopyrite which are localized in the norite zone, close to the contact with the underlying rocks. The nickel content of the norite is probably less than 1 pct, and the nickel content of the pods and lenses within the norite is about 1 pct. PROSPECTING APPROACH Although the areas are different geologically, the approach in prospecting them is fundamentally the same. The procedure is twofold: 1) a rapid reconnaissance survey to outline an area of high nickel content, and 2) a more detailed survey to outline zones of possible ore grade within the area of high nickel. The possible ore at Red Flats is concentrated in the lateritic soil, whereas at Little Rocky Creek it is in the sulfide pods. Both types are surrounded by an area of relatively high nickel content. CHEMICAL ANALYSIS Chemical analyses of nickel were made by a di-methylglyoxime colorimetric test, similar to the standard test for nickel, utilizing concentrated sul-furic acid for extraction. The lower limit of detection for nickel in soil by the method used was about 10 ppm and for nickel in plants about 5 ppm. The relative deviation was about 25 pct. SOIL PROSPECTING General Statements: A summary of the approximate average parts per million of nickel in soil, as compiled from the literature and from my study, is given in Table I. Selected references are given at the end of the paper. Few of the investigators reported the type of extraction or analysis, so the data given may not be strictly comparable to mine, which were made with a sulfuric acid extraction. Any nickel concentration greater than these average values might be considered anomalous, although each area must be studied in relation to the surrounding rocks. Method of Soil Sampling: The soil samples were taken in a zone from 1 in. to 1 ft below the humus layer, and within a 15-ft radius around a station.

Jan 1, 1961

By H. H. Stoek, G. W. Harries

The term " Anthracite Coal-Field " is generally used to refer to a comparatively small territory lying in the eastern-central part of Pennsylvania. This territory includes about 3,300 sq. miles of area, located chiefly in five counties in which anthracite-mining is the dominant industry. Although an area of 3,300 sq. miles is embraced in the region, less than one-fifth of this area, or only 484 sq. miles, is underlain by workable coal-seams. Moreover, this prorluctive portion is not a continuous area, but consists of a number of detached basins. These are known as the Northern, containing 176 sq. miles; Eastern-Middle, containing 133 sq. miles; Southern, containing 181 sq. miles; and western-Middle,containing 194 sq. miles. From the standpoint of business and trade, the region is divided into three districts, known as (1) the Wyoming, which includes the Northern field and the small Bernice basin; (2) the Lehigh region, which includes all of the Eastern Middle field and that part of the Southern field east of Tamaqua; and (3) the Schuylkill region, which includes the WesL ern-Middle field and that part of the Southern field west of Tamaqua. The relative commercial importance of these districts at the present time is shown by the coal-shipments as given in the following table :

Jan 1, 1904

By John Wulff, David A. Stevenson

The rates of solution of copper, nickel, and three copper-nickel alloys in liquid lead were studied at 527° and 727°C under dynamic conditions. The relative velocity at the solid-liquid interface was varied from 8.65 to 125 cm per sec. Analysis of the data for the pure metals indicates that the solution rate is transport corztrolled at lower velocities, but a transition to mixed control occurs at higher velocities, higher temperatures, and higher percent saturation. 1 HE present work concerns the effect of relative velocity at a solid-liquid interface on the dissolution kinetics of pure solid materials in liquid metals. This general problem is of interest in electrode kinetics, in electrolytic processes, and more recently in the field of liquid metal corrosion. Considerable work has been done on dissolution kinetics in aqueous environments because of the obvious importance to electrolytic processes.1,2 In purely metallic systems investigation has been more limited. There are, of course, extensive data from loop tests which are used in an engineering evaluation of liq- uid metal corrosion. Here, however, the dissolution process is complicated by several interdependent processes. In general, one of two factors is considered to be rate limiting in the dissolution process: the transport of material from the solid-liquid interface into the bulk liquid, or an activation process directly at the interface. A number of studies of the dissolution rates of solid metals in liquid metals under static conditions have been published.3- Since the attendant hydrodynamic conditions imposed by thermal gradient convection and concentration gradient convection are difficult to analyze, it is doubtful if a clear interpretation of the experimental findings of these papers in terms of the mechanism involved in the dissolution process can be made. A clearer picture of the dissolution process is provided by

Jan 1, 1962

By Arthur Gibson

Synopsis.-A new feature in coal mining, where the coal is to be conveyed from a high to a lower elevation and the topography of the country is such as to preclude surface haulage. The distance from the mine to the tipple inn this instance is about 3,000 ft. and the difference in elevation between the terminals 321 ft., of which 225 ft. occurs in the first 1,300 ft. from the loading terminal. A mine car was designed especially for this plant consisting of two tramway buckets on one pair of trucks, the buckets being lifted from the truck, attached to the train line automatically, and conveyed to the tipple. THROUGHOUT eastern Utah, in the Book Cliff range and the Wasatch plateau, the coal-bearing measures are admirably exposed, in the bold and for the most part bare escarpments. The geology is simple, the rocks being almost flat, or at the most dipping not more than 10 per cent. The coal beds occur in a formation, or group of strata, consisting of sandstone and shale, 600 to 800 ft. thick, which has been correlated with the Mesaverde formation of the Cretaceous. Above this occurs about 2,000 ft. of alternate layers of buff-colored sandstone and shale. Below the coal lie the Colorado shales, which are estimated to be about 1,500 ft. thick, below which are the red rocks of the Jura-Trias. As a rule the coal beds all clip in a northerly direction and under the high mountain. The canyons opening out into what is known as Castle valley all cut the coal beds, and the beds rising in the direction of the valley are found frequently high up on the escarpment, often as much as 1,000 ft. above the valley. The surface features of the region have an economic bearing on the availability of the coal. The valleys and gulches in the Colorado shale extend out from the coal areas across the edge of the plain, so that it is impracticable to build transportation lines parallel with the boundaries of the field within several miles of the coal land. It will be necessary, therefore, to build branch lines up to the coal lands from points on the Denver & Rio Grande Railroad traversing Castle valley.

Jan 10, 1914