Search Documents

By R. W. Shoenberger, J. D. Clendenin, W. L. McMorris, N. Schapiro, B. R. Kuchta, A. A. Terchick, R. J. Gray, J. G. Price

INTRODUCTION * The United States is fortunate in having enormous reserves of metallurgical-grade coals. Although these coals are better in quality and more accessible than most coals found throughout the rest of the world, the best grades of these coals are being depleted. Consequently, more efficient exploration tools and techniques, such as advanced methods of core drilling and logging, correlation by palynology,** stratigraphy, paleontology and petrography are being used to help assess the extent and quality of the remaining coal reserves. Exploration and assessment of new and existing coal properties become of utmost importance in determining (1) the economic justification for mining the coal, (2) the optimum design of the preparation plant and (3) the most effective use of the coal. Fortunately, the cost of mining coal has remained stable because of better mine planning, more efficient operations and increased mechanization of mining operations. However, increased mechanization raises the amount of impurities in the coal mined, and this requires more and better coal beneficiation to meet the more stringent quality requirements set by the market. Besides, mechanical miners also produce relatively fine coal and, to ensure maximum liberation of impurities, much of the coal presently being used must be crushed to a finer size prior to preparation. The bulk of all coals presently used in this country is mechanically cleaned, much of it at a lower specific gravity than in the past. This necessitates the use of new and improved processes and equipment for coal washing and recovery, such as heavy-medium cyclones and vessels, and froth flotation cells. However, because wet-cleaning processes are pre- dominant in the United States and fine coal retains large amounts of moisture, the increased production of cleaned fine coal accentuates the need for new or improved methods and equipment for dewatering and drying this coal. The larger amounts of coal being beneficiated and the use of new and improved beneficiation processes will aid in controlling and ultimately eliminating sources of pollution. Modem coal markets demand coals that meet rigid specifications. Most coals are purchased under contracts that specify moisture, ash, and sulfur contents, or heating value, depending upon the end use. There has also been a growing trend toward specifying other properties, including particle size and coking capability. These specifications may include not only the * Editor's note: Because of the numerous and varied contributions of the associate authors of this chapter, the text does not differentiate between sections prepared by each individual as has been done in other chapters. ** Palynology is the study of plant microfossils, especially spores, pollen, and other types of fossils not usually studied by paleontologists.

Jan 1, 1968

Jan 1, 1923

Jan 1, 1923

By R. K. Hopkins

For a great many years fusion welding has been used in and around petroleum refineries, but it is only within six or seven years that the more important pressure vessels have been constructed by this process, because before that time the properties of fusion welds would not with-stand such rigorous service. Since the adoption of fusion welding for the construction of this equipment, the refiner has required pressure vessels suitable for operation over a very wide range of conditions. On the one hand, vessels must operate at extremely high temperatures, in the range of 950° to 1000° F., and on the other vessels must be suitable for operation at sub-zero temperatures down as low as -75° F. Also, vessels are required suitable for operation at pressures upwards of 1000 lb. per sq. in., and as low as a 29-in. vacuum. In addition, vessels are required to withstand the attack of very corrosive mediums. It has been a rather difficult task for the fabricator to meet all of these require-ments, but as a result of the extensive research carried on by steel manu-facturers and several fabricators of class I vessels, practically all of these demands have been met. In order to meet the refiners' requirements for this wide range of conditions, the fabricator has worked closely with the metallurgist. This has enabled him to choose the proper base metal for each service condition, but it has been the fabricator's problem to develop a welding rod and welding technique, as well as a heat-treatment, that would produce in the welded vessel characteristics in and around the weld comparable to those in the base metal. Where corrosion is not a serious problem, and where the operating temperatures are not too high, ordinary carbon steel has served very well. But when corrosion is serious, and/or when the temperatures are either very high or very low, it is necessary to use some form of alloy steel to give satisfactory service.

Jan 1, 1935

By M. Shelef, A. W. Fletcher

The effect of alkali sulfates in promoting the sul-fation of nickel and copper in a bulk sulfide flota -tion concentrate by fluidized bed roasting has been studied in the laboratory, and it was shown that the various alkali sulfates promote sulfation to approximately the same extent. The sulfation of a mixture of synthetically prepared iron and nickel oxide and of nickel ferrite has also been studied. Nickel sulfation was promoted by high ratios of Fe:Ni and by the presence of sodium sulfate. THE work described in this paper was a continuation of earlier studies into the role of alkali sulfates in promoting the sulfation roasting of nickel sulfides1,2 in an endeavor to determine how the system was affected by the presence of compounds of iron and copper. The earlier work1 showed that, in the sulfation of NiO at 680°C, the reaction was limited by the formation of an impermeable film of nickel sulfate on the oxide surface. The relative effect of the various alkali sulfates in promoting nickel sulfation varied in the order: Li > Na >Cs > Rb > K A study of alkali sulfate/ nickel sulfate interactions at high temperatures showed that the promoting action was due to the fact that the nickel sulfate product layer sintered and agglomerated only when the more active additives were present. This resulted in the formation of discontinuities in the nickel sulfate layer so that diffusion of the sulfating gases to the NiO surface was no longer impeded and the reaction could proceed to completion. A similar explanation was used for the observation that sodium and lithium sulfates promote the oxidation of NiS to NiO at temperatures below 750°C since small amounts of nickel sulfate were formed during oxidation.2 It was of interest to study the effect of alkali sulfates on the sulfate roasting of a sulfide flotation concentrate which is typical of material treated commercially. In order to control temperature it is essential to roast sulfides in a fluidized bed and this technique was therefore used, although the batchwise operation of a small-scale laboratory reactor does not reproduce all conditions which prevail in full-scale continuous plant. The results obtained are therefore only comparative, and cannot be used for predicting the optimum conditions for metal extraction. The sulfation of synthetically prepared mixed oxides of nickel + copper and nickel + iron and of nickel ferrite was also studied to evaluate the relative effects of alkali sulfates with more complex systems. SULFATION ROASTING OF A SULFIDE FLOTATION CONCENTRATE The bulk sulfide flotation concentrate used in this work contained 7.92 pct Ni, 1.74 pct Cu, 35.66 pct Fe, and 31.28 pct S. The sulfide minerals present in order of abundance were pyrrhotite FeS, pyrite FeS2, pentlandite (FeNi)S, and chalcopyrite CuFeS2. Two samples described as coarse and fine were used. The coarse sample, which was a flotation concentrate (58 pct plus 300 mesh), was ground to 100 pct minus 350 mesh to produce the fine sample. Before roasting, the sample of sulfide concentrate was agglomerated by wetting witli a solution of the alkali sulfate (or water), thoroughly mixing, and drying at 110°C. This gave a cake which was gently crushed and screened, the -18 +100 mesh fraction being used for fluidized bed roasting. A similar-size fraction had been used by the authors in pilot plant work with a 4-in.-diam fluidized bed reactor.' In this work it was found that the molar ratio of additive to the total iron + nickel + copper content of the sulfide sample should be adjusted to a value of approximately 0.06, as this was the optimum amount necessary for nickel sulfation. Experimental. The fluidized bed reactor consisted of a quartz tube approximately 60 cm long and 30 mm in diameter resting in a vertical tube furnace. The sulfide bed (30 g) was supported on a bed of -4 +12 mesh quartz particles 3 cm high, which rested on a sintered quartz disc welded to the tube. The temperature of the furnace was controlled with a variable transformer to give a final bed temperature of 680°C. The bed was fluidized with air or mixtures of air + 10 pct v/v SO2, at a total apparent gas velocity of 60 to 65 cm per sec at 680°C. The SO2 was introduced into the fluidizing air stream only when the oxidation of the sulfides was completed. At the end of the roasting period the calcine was leached with boiling water and the

Jan 1, 1964

By C. E. Taylor, L. V. Fegan

With on-stream electrical-resistance measurement as a basis, Bethlehem Steel developed a system for the completely automatic control of moisture in the feed to pelletizing. This system was later successfully adapted to the sintering process, with automatic control of moisture serving to maintain the air permeability required for effective burnthrough. Control of moisture content is an important factor in the agglomeration processes by which iron ores are converted into either pellets or sinter for use in blast furnace burdens. In both pelletizing and sintering the iron ore feed must be mixed with the proper amount of water so that capillary attraction and surface tension forces can be utilized to cause the ore particles to coalesce and form larger agglomerates. The success or failure of the entire pelletizing or sintering process depends on maintaining the proper moisture. Therefore, continuous automatic control of moisture is one of the conditions for the automation and optimum use of both pelletizing and sintering processes. In pelletizing, variation in moisture can cause ball size to change and is a common cause of cycling which results in a fluctuating feed to induration. Excessive moisture can cause lumps to form at the cutter bar and contributes to the formation of buildup on the green pellet screens. Green pellets with excess moisture deform and reduce bed permeability. In sintering, accurate control of moisture is also important because moisture must be within the limits that give the bed the required permeability for good burnthrough. In response to these problems, a moisture meter, based on the principle of electrical resistance measurement, was developed. This moisture meter has been a key factor in the development of systems for providing uniform feed of concentrates in most of Bethlehem's pelletizing and sintering plants. The automatic moisture control system for pelletizing was successfully plant-tested and resulted in the following: (1) Control of moisture in the green pellets to +0.2%. (2) Up to 50% reduction of bentonite consumption. (3) Control of unscreened green pellets so that 85% of the furnace product at Cornwall was within the size range of -5/8 +3/8 in. (4) Improved quality of product with a tumble test of 94 and a "Q" index of 90 as the result of feeding a consistently uniform feed to a shaft furnace. In sintering, where sinter-mix temperature change and variable feed could cause errors in moisture measurement, the system was designed to maintain the correct moisture under virtually all plant operating conditions. It was successfully plant-tested and is now in use in most of Bethlehem's sintering plants. The system achieves: (1) Control of moisture within the desired limits for optimum production. (2) Continuous measurement and control of moisture even with intermittent feeding of mix, so that attention by the operator is seldom required. The two automatic control systems provide smoother startup, minimize upsets and contribute to the consistent control of process variables in pelletizing and sintering. MOISTURE-CONTROL SYSTEM FOR PELLETIZING Fig. 1 shows the general arrangement of the system for automatic control of moisture in pelletizing.1 In this system a bin level controller, using a single probe which regulates filter speed, maintains a uniform low concentrate level in the bin.' The moisture meter, comprised of an analyzer and control components, continuously measures the moisture in the bed and adds water to adjust to the desired level. The meter is placed in an open-loop (feed-forward) control, i.e., water addition occurs downstream from the probes. Filter vacuum must be set so as to produce a filtercake moisture which is below the optimum for pelletizing. Bentonite is added after the

Jan 1, 1969

By Charles H. Fulton

Experimental work on the process was begun on a laboratory scale at Cleveland, Ohio, in 1914, and transferred to East St. Louis, Ill. in 1916, where a commercial sized furnace was in technical operation until January, 1918. The essential steps of the process are as follows: Oxidized zinc ore or roasted zinc concentrate is mixed with crushed coke and coal-tar pitch and formed into briquets 9.25 in. (23.5 cm.) in diameter and 21 in. (53 cm.) long in a manner similar to that used in the manufacture of graphite or carbon electrodes, except that much less care and time are required. The composition varies with the nature of the ore; in one case, the composition was 100 parts ore, 70 parts coke, and 18 to 20 parts pitch. These briquets maintain their form and volume during and after the distillation of the zinc. This object is gained by using coke as the matrix and coal-tar pitch as the binder; this pitch becomes coke on heating and unites the ore particle and the original coke particle into a continuous mass. The briquet is an electrical conductor but only to such a degree that it can be used as a resistor. The size of the ore, as in the present practice of zinc metallurgy, ranges from fine material, such as flotation concentrate, to coarse table and fine jig concentrate. The process is not restricted to any particular kind of ore, but is applicable to pure high-grade ores, ores high in iron, and complex zinc-lead ores, since the residue from the distillation IS held immovably in place within the briquet. In the case of complex zinc-lead ores, the distillation is conducted with a carefully regulated temperature so that a high percentage of lead is retained in the distilled briquet, which may then be smelted for its lead content. In present zinc smelting practice, the reduction fuel is from 40 to 50 per cent. of the weight of the ore. In the briquet, it is from 60 to 85 per cent. of the ore; but unless the ore is exceptionally high in residue, the distilled briquet may be used over again as coke, or as a high ash coke for fuel purposes in power production. Baked briquets are hard and tough and may be handled roughly

Jan 1, 1921

By W. C. Lacy

THE Cuajone porphyry copper deposit is the northernmost of a group of three deposits in southern Peru controlled by the Southern Peru Copper Corp.-Toquepala, Quelleveco, and Cuajone— all within a 20-mile belt. Although small pockets of high-grade copper oxide ores were worked in the Cuajone area in the 19th century, it was not until 1939 that its potentialities as a disseminated deposit were recognized by 0. C. Schmedeman. An exploratory drilling pro- gram was begun in December 1942 and continued until early 1945. The program was revived in November 1952 and completed early in 1954. Early exploration was by diamond drilling. Later exploration was predominantly churn drilling, with diamond drilling used only for wildcat holes. Along this northwest-trending belt of deposits. which follows the western slopes of the Andean Range, quartz-monzonite has invaded earlier dio-rite intrusives and a series of warped and tilted Cretaceous volcanic flows. Little faulting of consequence has been recognized within the mineralized areas. Sulfide minerals were introduced into all these diverse rocks, and mineralization was followed by erosion, oxidation, and enrichment. In Late Tertiary and/or Quaternary time the entire

Jan 1, 1959

By N. B. Davis

I . INTRODUCTION WHILE working with a number of very sticky cracking clays from western Canada the writer became interested in a study of the cause of the excessive plasticity, This led to a review of the rather bulky literature on the subject and the finding that plasticity still remains to be satisfactorily explained. Most of these investigations seem to have been carried on solely from the chemical viewpoint, the geologic aspects having been ignored. In nearly every case, the investigators have worked with the higher-grade clays of low to medium plasticity, such as the kaolins, the excessively plastic ones having generally been neglected, partly because of their limited application, yet the author believes that these are

Jan 2, 1915

By Robert D. Pike

In November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: Stone Completely Calcined CaO(Sro)a............. 30.35 57.806 Mgo................... 21.55 41.050 SiO2. ................... 0.30 0.572 R2O3................... 0.30 0.572 Ignition loss............. 47.50 a SrO about 0.06 pct. Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2'3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depending upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1948

By C. J. Bonnecarrere, P. A. Jr. Bloomer, J. Hunter

Since 1941 not more than 15 per cent of aii wildcat wells drilled in Louisiana have been successful. This figure is not too discouraging, especially in view of the fact that during the same period approximately 80 per cent of all wells (average 701 wells per year) drilled in or adjoining producing areas were successfully completed. However, a somewhat discouraging aspect concerning Louisiana's wildcat completions is that in 1942 only 12 out of 20 fields found were oil fields; in 1943, only 13 out of 24; and in 1944, only 8 out of 21. This means that an operator has less than a 50:50 chance of finding an oil field. In other words, it is more likely that he will find a gas-condensate field. This fact has become increasingly evident as the data for each year are compiled and compared. Yet, strangely enough, operators are reluctant to accept this fact and plan accordingly. Certainly they cannot continue to search for oil fields and, for the most part, end with shut-in gas-condensate wells. The reason for shutting in is that there is no immediate and satisfactory market for all the gas being discovered. The solution, and it is a very satisfactory one, as experience in Louisiana has already demonstrated, is cycling. The advantages of this type of operation of gas-condensate fields, especially where the entire field is pooled and unitized, should be self-evident. These advantages will become increasingly more important, especially now that legislatures, regulatory bodies, royalty owners, and others are beginning to realize that "reasonable development" in a field is not indicated by the number of wells completed, but rather by the method of development. To complete a great many wells that can produce at only, partial capacity is waste. Producing hydrocarbons from these wells and not subjecting them to processing by surface operations, in order to recover all liquefiable hydrocarbons, is waste. Permitting bottom-hole pressures to drop or gas-oil ratios to increase because of excessive production is waste. Loss of leases and of wells because of inability to produce or to meet lease obligations is waste. Therefore, it is becoming increasingly apparent that a reservoir entirely pooled and unitized with a minimum number of completions, but over which there is exerted careful control so as to provide maximum recovery and the processing of all hydrocarbons brought to the surface, is the only logical and reasonable method of developing a gas-condensate field. Oil Production Twenty-one new fields, including three rediscoveries, were found during 1944. Three of these new discoveries—Delhi in northeast Louisiana, Good Hope in southeast Louisiana, and West Tepetate in southwest Louisiana—should add considerably to Louisiana's oil reserves. The other discoveries were either gas condensate or of apparently little consequence. State-wide productioll for 1944 was 1366 million barrels of crude oil and condensate; amounting to about 8.1 per cent of the

Jan 1, 1945

By H. H. Uhlig

Soon after general use of stainless steels began, it was observed in practice that certain combinations of factors tended to induce corrosion by pitting. For most applications this was a serious drawback, not so much because the structural properties of the metal were impaired but because of the rapidity with which heavy sections of the alloys were penetrated by small elongated pits. These pits seemed to initiate readily in oxidizing metal salt solutions like ferric chloride and in chloride solu-tions like sea water. It was observed that in sea water pitting was more frequent in stagnant or polluted waters than in highly aerated, moving waters. The steels in these chloride solutions were observed to be sensi-tive to long contact with material such as sand grains or attached bar-nacles. At points of attachment or contact it was not uncommon to discover initiation of corrosion. Pits once begun at contact faces were observed to grow rapidly, usually elongating phenomenally in the direc-tion of gravity until the metal was perforated. Hydrochloric acid and other nonoxidizing acids, on the other hand, were observed to corrode stainless steels generally; the weight losses often were higher, but the penetration less than for the pitting type of corrosion. The causes of pitting, a type of corrosion recognized as character-istic not only of stainless steels but of many additional metals and alloys, are important in corrosion studies. A possible explanation bears prac-tical significance, for once it is known why pits begin where they do and continue to grow after initiation, intelligent direction can be given to diminishing corrosion. This can be done either by some alteration in the composition and treatment of the alloy or by some alteration in the environment. It appears foremost in importance to discover the nature of pit foci, for if initiation of pits can be discouraged their growth will be no longer a factor to be considered. In a multi-component alloy containing many impurities normal to production of such an alloy, each of which may play a part in pitting, and whose corrosion resistance is sensitive to heat-

Jan 1, 1940

By Robert D. Pike

In November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: Stone Completely Calcined CaO(Sro)a............. 30.35 57.806 Mgo................... 21.55 41.050 SiO2. ................... 0.30 0.572 R2O3................... 0.30 0.572 Ignition loss............. 47.50 a SrO about 0.06 pct. Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2'3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depending upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1948

By C. Zener, J. H. Hollomon

IT Is commonly recognized that a given material may be described as ductile or brittle only with reference to the conditions of test. Thus under the usual test conditions quartz is brittle, but under high pressures it is ductile. Salts that are brittle at room temperature become ductile at elevated temperatures. Pitch, brittle with respect o rapid loads, flows at low rates of loading. Pearlitic steel, ductile under the usual conditions of test, may be embrittled under the proper conditions of combined stresses, temperature, and rate of loading. EARLIER INVESTIGATIONS A clear analysis of the conditions necessary for plastic flow and for fracture was first given by Ludwik,1 who introduced two types of stress, the "flow stress" and the "stress at fracture." These stresses may refer to tensile or to shear stresses, or, in fact, to any type of stress. Ludwik considered these two stresses to be independent of one another, functions of the conditions of test and of the prior history of the material. For the purpose of analysis, both a flow stress and a stress at fracture can be envisaged as functions of strain over the entire range from zero to infinite strain. Thus, the material is brittle if the stress at fracture is less than the flow stress and ductile if the reverse is true. According to Ludwik's analysis, the problem of determining the effects of combined stresses, of temperature and of strain rate upon the behavior of metals reduces to a problem of determining the effect of these variables upon the flow stress and upon the stress at fracture. In the present paper, methods are described for determining the effects of two of these variables, temperature and strain rate, and examples are given of the dependence or now stress and stress at fracture, upon these two variables. The effect of combined stresses will be discussed in a succeeding paper. The flow stress may be determined from a load-diameter curve. Load-diameter curves were obtained over a wide range of temperature and over the limited range of strain rates obtainable with the lever-type Riehle machine used. The. curves were then converted to an extremely wide range of strain rate by making use of the equivalence of the effects of changes in strain rate and changes in temperature, previously proposed2 and demonstrated' by the authors. According to this principle of equivalence, strain rate E and temperature T affect the flow stress only through a single parameter p of the form: p = EeQ/RT [I] In this equation, R is the gas constant (2 cal. per gram mol per deg. C.), and Q is a heat of activation, which varies from material to material, and may depend upon the strain, but not upon the strain rate or the temperature. There is associated with every value of p a flow-stress curve. Combinations of strain rate and of temperature that give the same p have the same flow-stress curve. Therefore, merely by changing the temperature of test, the effect of changing the strain rate may be obtained. Thus, under isothermal conditions, the material will behave the same at

Jan 1, 1944

Jan 1, 1898

By Albert A. Smith

The creep properties of metals have assumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Institute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investigate creep phenomena because of the simplicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals. Material The creep tests of this investigation were all made on high-purity lead (99.9998+ Pb) in which the only impurity that could be detected by spectrographic and chemical means was approximately 0.0001 per cent Fe. Flat strips, 0.750 in. wide by 0. 100 in. thick, were prepared by extruding 2-in. dia. cast billets at a temperature of 250°C. This gave a material of 2 to 3 mm. average grain size with a tensile strength of j.400 lb. per sq. in. when tested at a straining rate of 5 per cent per minute. With this extremely soft material, great care was necessary in handling the specimens, to avoid distortion and subsequent recrystallization. The creep tests at 30°C. were conducted in a constant-temperature room, specially built for the purpose in the basement of an office building in which there was no moving machinery, and no vibration was detectable under the most severe conditions of shock in the adjacent surroundings. The room was well insulated and heated electrically, control being by means of a de Khotinsky regulator operating a relay. Maximum temperature variation over a period of several years has been ± 1/2°C. Specimens of the extruded strip, 16 in. long, were used for test purposes with no reduced gauge section, thus eliminating any distortion due to machining. The method of clamping and supporting the specimens is shown diagrammatically in Fig. 1. The gauge marker for the measurement of extension consisted of an aluminum strip, 0.050 in. thick by 0.75 in. wide, one end of which was ground and sanded to a precise knife-edge and fastened to the specimen by suitable pins. After the strip was fastened in place a fine scratch was inscribed just below the knife-edge by means of a sharp teasing needle. Just below this gauge scratch a short vertical mark was made so that the same point could be located and read each time. Several hundred specimens have been prepared by this method, and it was found that with experi-

Jan 1, 1941

By H. C. H. Darley

The influence of particle size and concentration on the development of chip hold-down pressure (CHDP) was studied in an apparatus designed to measure the change of filtration rate during the first second of the filtration process. CHDP is controlled by the "bridging" particles (i.e., particles in the 50 to 0.2 micron range), whereas filter loss is controlled by the colloid fraction. The results indicated that a fast drilling fluid with a low filter loss could be obtained if the concentration of bridging solids and the viscosity were kept very low. A novel group of drilling fluids, which we have named colloid emulsions, was developed to meet the above requirements. These colloid emulsions are made by dispersing art oleophilic colloid in oil and emulsifying about 5 per cent of this dispersion in water or a dense brine. Good results have been obtained in field trials with emulsions which use asphalt as the oleophilic colloid. INTRODUCTION In recent years it has been found that fast rates of penetration can be maintained in hard formations by using "clear" water as a drilling fluid. In some cases, however, water cannot be used because the very high down-hole filter loss creates various difficulties in drilling, in logging, or in producing the well. It then becomes necessary to "mud up", which results in a decrease in drilling rate. The reason that mud decreases drilling rates is a complex subject which has been well covered by such authors as Garnier and van Lingen, Cunningham and Eenink,' and van Lingen.3 One of the principal factors involved is the tendency of the drilling fluid to develop a filter cake on the bottom of the hole. The pressure differential which develops across this filter cake opposes the action of the bit in dislodging chips from the rock. This pressure differential is referred to by Garnier and van Lingen' as the chip hold-down pressure, which is denoted by the initials CHDP in this paper. The work described in this paper was undertaken to develop a drilling fluid which would minimize CHDP but which would still have a low filter loss—in other words, a fluid which would deposit a filter cake on the sides but would lay little or no filter cake on the bottom of the hole. EVALUATION OF CHDP EXPERIMENTAL Conditions governing the growth of filter cake on the sides of the hole are obviously different from those on the bottom of the hole. On the sides of the hole, cake will form continuously but at a decreasing rate, until eventually the rate of growth will equal the rate of cake erosion by the mud stream.' On the bottom of the hole, each time a bit tooth dislodges a chip the cake is removed, a fresh rock surface is exposed, and the filtration process must start over again. Thus the CHDP is determined by the amount of cake which can form in the interval between successive tooth strikes at a particular spot, normally a fraction of a second. Our first step therefore was to study filtration rates over the first second or so of the filtration process. These tests were conducted in the simple type of dynamic filter cell shown in Figs. 1 and 2. In this cell the mud was filtered through a train of rock cores while rotating blades kept the mud flowing over the surface of the core. The procedure was to evacuate the cores to 0.05 mm of mercury, saturate with brine, and assemble in the holder under brine. The permeability of the core train was then determined. A plastic seal was placed on the face of the core train, and a rip cord was attached from the seal to one of the blades. At the start of the test, 500 psi was applied to the mud, and the meniscus in the capillary measuring tube was adjusted to zero. When the blades were started, t,he seal was ripped from the face of the core, and filtration began. The filtration rate was at first measured by photographing the advance of the meniscus in the capillary tube. Using

Jan 1, 1966

By Albert A. Smith

The creep properties of metals have assumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Institute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investigate creep phenomena because of the simplicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals. Material The creep tests of this investigation were all made on high-purity lead (99.9998+ Pb) in which the only impurity that could be detected by spectrographic and chemical means was approximately 0.0001 per cent Fe. Flat strips, 0.750 in. wide by 0. 100 in. thick, were prepared by extruding 2-in. dia. cast billets at a temperature of 250°C. This gave a material of 2 to 3 mm. average grain size with a tensile strength of j.400 lb. per sq. in. when tested at a straining rate of 5 per cent per minute. With this extremely soft material, great care was necessary in handling the specimens, to avoid distortion and subsequent recrystallization. The creep tests at 30°C. were conducted in a constant-temperature room, specially built for the purpose in the basement of an office building in which there was no moving machinery, and no vibration was detectable under the most severe conditions of shock in the adjacent surroundings. The room was well insulated and heated electrically, control being by means of a de Khotinsky regulator operating a relay. Maximum temperature variation over a period of several years has been ± 1/2°C. Specimens of the extruded strip, 16 in. long, were used for test purposes with no reduced gauge section, thus eliminating any distortion due to machining. The method of clamping and supporting the specimens is shown diagrammatically in Fig. 1. The gauge marker for the measurement of extension consisted of an aluminum strip, 0.050 in. thick by 0.75 in. wide, one end of which was ground and sanded to a precise knife-edge and fastened to the specimen by suitable pins. After the strip was fastened in place a fine scratch was inscribed just below the knife-edge by means of a sharp teasing needle. Just below this gauge scratch a short vertical mark was made so that the same point could be located and read each time. Several hundred specimens have been prepared by this method, and it was found that with experi-

Jan 1, 1941

By J. W. Eckerd, P. S. Lewis, N. H. Coates

USBM designed, constructed, and operated an 18-in.-diam fluidized-bed combustor for highly caking coals to evaluate the method for possible application to power generation. In initial tests, combustion was carried on successfully, with carbon losses as low as 0.8%+ Coal ash was not satisfactory as a bed material, but mullite proved to be acceptable. Overall heat-transfer coeffients from the bed (-20 t 50 mesh mullite) to a water-cooled tube were about 75 Btuper hr-sq ft. Fluidized-bed combustion is being investigated by the U. S. Bureau of Mines (USBM) as a potentially cheaper method of firing power plant boilers. Lower combustion temperatures in fluidized beds—only 1400" to 1800°F-—should reduce fireside deposition and corrosion and nitrogen oxides production. Fluidized-bed combustion also offers possible advantages in the use of additives to control SO, emissions and amenability to processing of high-ash, high-moisture coals without special preparation. This paper describes development of a fluidized-bed combustor and the results of preliminary tests. Equipment and Procedure Fig. 1 shows the 8-ft-high combustor. A cone-shaped plate perforated by I/8-in.-diam holes supports the fuel bed and admits the fluidizing air; water passing through the 3/4-in. pipe extracts heat from the combustion bed. Fig. 2 is a flow diagram of the system. Coal is fed pneumatically to the base of the fuel bed. Combustion products are passed through two centrifugal separators to remove most of the entrained solids, then to a water

Jan 1, 1971

By E. W. Mehal, R. W. Haisty, D. W. Show

The next generation of integrated circuits will probably include circuits constructed in and of GaAs. The existence of both semi-insulating and semiconducting forms of GaAs is the fact which will bring this about. In this paper we discuss the uses and limitations of semi-insulating GaAs for integrated-circuit applications. The two main areas considered are the electrical isolation that can be achieved between components on a semi-insulating substrate and the characteristics of p-n junctions in contact with semi-insulating GclAs. A process basic to attaining integrated circuits in GaAs to fully utilize the insulating properties of the substrate is selective epitaxial deposition. This process involves the deposition of a SiO2 layer onto a The trend in integrated circuits is towards the use of high-resistivity substrates or regions to achieve component isolation. The use of SiO, layers in the oxide isolation methods and the use of sapphire substrates are examples of this idea. GaAs is also a polished surface of a GaAs substrate, etching out selected area of the SiO, film to expose a GaAs surface, and deposition only onto the exposed GaAs surface. By using this process , islands of semiconducting GaAs are deposited onto a semi-insulating GnAs substrate, the islands being electrically isolated from one another by the substrate. The deposition of both p- and n-type semiconducting GaAs can be carried out in this nzanner to form p-n junctions in the island areas. This process can also be used to produce a planav structure by deposition of GctAs through a SiO, mask into holes etched into the GaAs substrate. This Putterned Epitaxial Technology (PET) is described. very promising material for use in future integrated circuits because of the existence of both semi-in-sulating and semiconducting forms. Active devices can be fabricated in the semiconducting material, and these individual components can then be electrically isolated from one another by using semi-insulating GaAs as the substrate. Epitaxial semi-insulating GaAs can also be produced thus making three-dimensional monolithic integrated circuits feasible.' This paper describes the research aimed at developing the methods for producing both two- and three-dimensional integrated circuits in GaAs, and examines some of the properties of semi-insulating GaAs as they relate to these integrated circuits.

Jan 1, 1967