Search Documents

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers.1, 2, 3, 4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The cndursnce limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers.1, 2, 3, 4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The cndursnce limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

By E. A. Gulbransen, J. W. Hickman

ONE of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film A comprehensive program has been undertaken to study these phenomena This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C Before the introduction of the electron diffraction technique, it «as necessary to use either direct chemical analyses or X-ray diffraction analyses to determine the nature of the oxide film formed on the metal or alloy Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry In special cases the information obtained may be identical, but in general both view-points are necessary Much of, the early work was carried out on the oxidation of bulk samples where thick films were obtained The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses Although much useful information has been obtained in this manner, little could be learned about the character of the protective oxides during the period when the films were actually protective Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective LITERATURE The oxidation of iron has been extensively investigated by X-ray and electron diffraction Jackson and Quarrell1 found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe304, between 515° and 900°C the stable film was FeO Above the upper change point of iron the oxide was found to be Fe304 prom 400° to 515°C , FeO, Fe304 or a mixture of the two oxides was found Recrystallization of the air-formed film below 400° and above 900°C led to the formation of Fe304 In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described

Jan 1, 1946

By A.S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric Pressure and by heat transferred to it from rock at high temPerature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. Methods Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1943

By S. C. Oliphant, R. Floyd Farris

Presented in this paper is a summary of the results of experiments conducted in both the laboratory and the field during the past three years in connection with casing-perfora. tion problems. Included are studies of gun features that influence bullet performance and penetration, and studies of the effect of perforator bullets on casing and the neat cement in the annulus. Discussion and data are also presented relative to the accuracy of depth measurements in deep wells. Introduction It is a common practice in the oil industry to effect the completion of oil wells by setting and cementing casing through the producing horizons and perforating the section of casing opposite the desired interval by means of a gun lowered into the well on a cable or on the tubing. This practice has been followed for some time, and this method of completion has been given considerable study by the companies that render perforating service as well as by the oil companies that utilize their services. Through continued research on this subject, it has been possible to develop guns, bullets, and powder that will permit controlled firing at great depths, and penetration of as many as two strings of casing. It is the object of this paper to present the results of studies made of gun perforating in both the field and the laboratory. These studies were made to determine the factors that affect penetration of the bullet, burring of the casing, accuracy of depth measurements, and other items. It is hoped that by presenting the results of these investigations a better understanding may be obtained of certain of the factors involved in gun perforating and further investigation of the subject will be prompted. Subsurface Tests A well approximately 9000 ft deep, which was being prepared for abandonment, was selected for subsurface tests of gun-perforating experiments, In preparing the well for the experiment, 51/2-in. casing in the hole was pulled and racked in the derrick. A test section of pipe, which consisted of 65 ft of 5-in. 18-lb J-55 casing centered inside 7-in. 28-lb N-80 casing, was placed in the derrick corner and the annulus between the two pipes was cemented from the bottom up with 161/2 lb per gal neat cement, which was mixed and displaced with a cementing truck in the usual manner. After the cement had been allowed to harden for about a week, the test section was lowered into the hole on the 51/2-in. casing to a depth of 6600 ft by casing measurements. The hole was filled with drilling fluid weighing 10 lb per gallon. A perforating company was called to perforate the pipe, but was not advised that an experiment was being conducted. The company was asked to check the total depth (to cross pins in the bottom of the test section), then to raise the gun a given distance and fire a given number of shots with 1/2-in. bullets, pick up another distance and fire a given number of 3/8-in

Jan 1, 1947

By K. A. Jackson, G. A. Chadwick, A. Klugert

The diffusion field ahead of a lamellar interfnce is analyzed using an electrical analog. A self-consistent solution is obtained for the shape of the interfnce and the diffusion field by an iterative process. The solutions presented here are for a 50-50 eutectoid or eutectic, The shape of the interface is found to he independent of growth velocity and lamellar spacing, and to depend on the relative values of interfacial free energies at the phase houndaries . The mode of growth of lamellar eutectics and eutectoids has been a subject of much interest for many years.1-4 Mehl and Hagel 1 have shown photomicrographs taken by Tardif when he attempted to determine experimentally the shape of an advancing pearlite interface; the results are completely ambiguous. Brandt' and schei13 have made approximate calculations of the composition ahead of a lamellar growth front. The shape of the advancing front and the composition distribution ahead of the front are difficult to calculate because one depends on the other. It is the purpose of the present paper to describe a method by which this calculation has been done. Lamellar-eutectic growth usually occurs under conditions where the growth is fairly rapid, and the interface temperature is close to the eutectic temperature. The growth rate is usually determined by heat flow. Eutectoid growth, on the other hand, can best be studied by quenching to some temperature, and allowing growth to proceed isother-mally. In both cases the growth is believed to be controlled by diffusion* rather than by the atomic kinetics of the transformation. This being the case, a single treatment of the diffusion equation will apply to both cases, provided the region of the interface in a eutectic may be considered to be isothermal. If a part of the interface could appreciably change its thermodynamic driving force by advancing ahead of or lagging behind the mean interface, then the two cases would not be similar. Eutectics normally grow in temperature gradients of the or-der of a few degrees per centimeter. The normal eutectic spacing is the order of a few microns. Part of the interface would have to extend many lamellar spacings ahead of the mean interface before it experienced sensibly different conditions. The interface temperature is usually a few tenths of a degree below the eutectic temperature so that temperature differences of the order of one-thousandths of a degree (a displacement of one lamellar spacing) would be unimportant. Protrusions large compared to the mean spacing do occur when one phase only grows into a eutectic liquid. This is usually a dendritic type of growth, and easily distinguishable from the lamellar mode of growth. A single treatment of lamellar growth will apply equally well to both eutectic and eutectoid decomposition. At the interface, which as shown above is essentially isothermal, the difference between the equilibrium eutectic temperature Teu and the actual interface temperature Ti, can be divided into two parts: 1) the composition varies across the interface, so that the local equilibrium temperature is not Teu; and 2) the interface is curved, so that the local equilibrium temperature is depressed according to the Gibbs-Thompson relationship. This undercooling can be written as Teu-Ti =?T = mAC(x) + a/r(x) [1] where ?C(X) is the departure of the composition at a point x on the interface from the eutectic composition, see Fig. 1, r(x) is the local radius of curvature at a point x on the interface, m is the slope of the liquidus line on the phase diagram, and a is a constant given by where s is the interfacial free energy, TE is the equilibrium temperature, and L is the latent heat of fusion. The calculations in this paper will be made only for the case where the phase diagram is symmetric, that is, the eutectic occurs at 50 pct, the liquidi have the same magnitude slope m at the eutectic temperature, and C,, the amount of B rejected when unit volume of a freezes, see Fig. 2(a), is the same for both phases. As shown in Fig. 2(b), the composition ahead of the a phase will be rich in B, the composition ahead of the ß phase will be rich in A. The composition at the phase boundary is the eutectic composition. The difference between the local liquidus temperature and the actual tempera-

Jan 1, 1964

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric Pressure and by heat transferred to it from rock at high temPerature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. Methods Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1943

By S. C. Oliphant, R. Floyd Farris

Presented in this paper is a summary of the results of experiments conducted in both the laboratory and the field during the past three years in connection with casing-perfora. tion problems. Included are studies of gun features that influence bullet performance and penetration, and studies of the effect of perforator bullets on casing and the neat cement in the annulus. Discussion and data are also presented relative to the accuracy of depth measurements in deep wells. Introduction It is a common practice in the oil industry to effect the completion of oil wells by setting and cementing casing through the producing horizons and perforating the section of casing opposite the desired interval by means of a gun lowered into the well on a cable or on the tubing. This practice has been followed for some time, and this method of completion has been given considerable study by the companies that render perforating service as well as by the oil companies that utilize their services. Through continued research on this subject, it has been possible to develop guns, bullets, and powder that will permit controlled firing at great depths, and penetration of as many as two strings of casing. It is the object of this paper to present the results of studies made of gun perforating in both the field and the laboratory. These studies were made to determine the factors that affect penetration of the bullet, burring of the casing, accuracy of depth measurements, and other items. It is hoped that by presenting the results of these investigations a better understanding may be obtained of certain of the factors involved in gun perforating and further investigation of the subject will be prompted. Subsurface Tests A well approximately 9000 ft deep, which was being prepared for abandonment, was selected for subsurface tests of gun-perforating experiments, In preparing the well for the experiment, 51/2-in. casing in the hole was pulled and racked in the derrick. A test section of pipe, which consisted of 65 ft of 5-in. 18-lb J-55 casing centered inside 7-in. 28-lb N-80 casing, was placed in the derrick corner and the annulus between the two pipes was cemented from the bottom up with 161/2 lb per gal neat cement, which was mixed and displaced with a cementing truck in the usual manner. After the cement had been allowed to harden for about a week, the test section was lowered into the hole on the 51/2-in. casing to a depth of 6600 ft by casing measurements. The hole was filled with drilling fluid weighing 10 lb per gallon. A perforating company was called to perforate the pipe, but was not advised that an experiment was being conducted. The company was asked to check the total depth (to cross pins in the bottom of the test section), then to raise the gun a given distance and fire a given number of shots with 1/2-in. bullets, pick up another distance and fire a given number of 3/8-in

Jan 1, 1947

By Harrison Souder

In view of the proposed visit of the Institute to Cuba this winter, the following brief sketch of the principal mineral deposits near Santiago de Cuba has been prepared largely from notes taken in February, 1903, during a visit to the mines then in operation in the province of Santiago de Cuba. Westward from Cape Maysi, the most eastern point of the island, the coast is rocky and uninviting. The usual course of the steamers is well in toward the shore, and the lines of stratification of the rocks can be distinguished clearly, the presence of iron or other ores being indicated by frequent blotches of mineral stain. One is impressed with the general rugged character of the southeastern coast-line,—an almost unbroken barrier of coral-limestone bluff's, full of caves and hollows, into which the surf rushes with a roar and bursts into tall fountains of spray. Beyond rises abruptly the Sierra Maestra range, whose sharp, peaked crest-line betrays its eruptive or igneous origin. From a height of about 800 ft. near Cape Maysi, this range gradually rises to the westward, attaining its maximum elevation of more than 8,300 ft. in the Pico Turquino, beyond Santiago. A general resemblance to the mountain-ranges of southern New Mexico is noticeable. At Daiquiri, 20 miles east of Santiago harbor, the extensive

Jan 1, 1905

By J. P. Pritchard, J. T. Pierce, O. G. Slay

This paper discusses the results of a technology-evaluation program to ascertain the feasibility of a piotornask-photoresist technology developed for fabrication of multiple-layer thin-film superconductive circuitry. The uehicle selected for this evaluation was a 120-bil associative data processor requiring a set of nine photomasks to define a similar number of patterned material layers of lead, tin, and polymer insulation. A total circuit area of 4 sq in. involved 2500 actitle and 12,000 passive crossings. Several short-free, electrically continuous specimens were satisfactorily completed under this program. Problems encountered in the preparation and use of the requi-ed set of Photomasks are discussed, as also are the problets of providing suitable external connections. A major retarding factor in the development of the superconducting thin-film cryotron technology for many years was the absence of batch fabrication means yielding necessary device density and count per substrate for practical applications. Early workers in the field desired only limited numbers of devices to permit careful study of discrete devices and representative circuitry integrating logic and memory capabilities. For these purposes mask stencils could be formed to selectively control the placement of materials, sequentially vapor-deposited in vacuum, to form the multilayer structure. In general a distinct pattern was required for each material layer; therefore, mechanical provisions were required to change not only the material source, but the patterning mask as well, before each deposition. All deposition steps were preferably performed in a single evacuation of the deposition chamber. Thus the means for storing, transporting, and registering masks and sources with respect to the substrate existed and were operated within the vacuum environment. In the authors' experience, the approach was and remains serviceable for preliminary device study, but was not extensible to an economical manufacturing method by virtue of the difficulties inherent in mask stencil preparation and use, and the capital investment implicit in the mechanization requirements. Since the commercial attraction of the cryotron technology stems principally from its potential for economical batch fabrication, the authors' program has placed major emphasis on fabrication methods. A highly useful method has evolved through adaptation

Jan 1, 1967

The problem of surface support in coal mining is naturally divided into three branches: 1. Surface covered with improvements of such value as compared with the value of the underlying coal, or with such elements of danger to mining, that absolute support is essential. 2. Surface with improvements of less value than the underlying coal such that moderate settlement may be permitted, but destructive settlement must be avoided, either by reason of danger to human life or unwarranted property damage. 3. Surface of relatively small value as compared with the underlying coal where destructive settlement may be permitted. First Problem In the first case it is evident that the original support must be maintained either (a) by leaving ample pillars and confining the coal recovery to a very conservative first mining, (b) by so supporting less conservative first mining by filling or flushing that the gradual deterioration of the pillars may be prevented and subsidence avoided, or (c) by incompressible support as masonry either as an adjunct to insufficient pillars or in place of the original coal support. a. From tests made by the Scranton Engineers Club, it appears safe to figure on 2000 Ib. per sq, in. as the safe squeezing strength of coal pillars in place, provided that these are, as usual, not higher than their least horizontal dimension; and from this figure the percentage of pillar to be left for various depths may be easily calculated. For safety in this

Jan 1, 1930

By William Rawles

THIS report is the first of a series planned by The Mineral Inquiry, organized by the American Institute of Mining and Metallurgical Engineers to make factual studies of the world's mineral resources in their political and international relations. The efforts of The Inquiry are directed toward filling certain notable gaps in available information, without duplication of many other investigations touching this field which are being conducted by other organizations, public and private. Much of its work is indirect-suggesting topics for study by other individuals and organizations and aiding in their planning and correlation. The present report is designed to show the nationality of the commercial control of mineral resources, in addition to the geographic distribution of production by nation-in other words, the overlapping of political and commercial control. Detailed accuracy cannot be claimed for the figures presented. For some companies division of ownership by nationality has been very difficult to ascertain, as many companies are reluctant to dis-close the extent of their holdings in other corporations, and the impossi-bility of tracing all stock ownership is obvious. Also there are frequent changes in the distribution of. stock control. The percentages given rep-resent only the participation that has been identified definitely, even though it is known in some cases with fair certainty that larger interests exist, as, for instance, American participation in foreign chromite companies. In bringing together these figures we have had the cordial co-operation of the United States Bureau of Mines, the United States Geologi-cal Survey, the Mineral Division of the Bureau of Foreign and Domestic Commerce, the Brookings Institution, and of many specialists connected with the mineral industries covered. The report does not cover the entire list of minerals. Coal, although it is one of the most important minerals, was omitted because , not more than one or two per cent of the world's production comes from mines that are owned by companies foreign to the countries where the coal is produced. Others, such as gold, are omitted because sufficient data have not yet been accumulated. It is hoped that some of these may be covered in subsequent reports. It is not our purpose here to discuss the significance of the figures sub-mitted, but only to point out the general nature of the problems on which they have a bearing.

Jan 1, 1933

By D. V. Doane, G. A. Timmons, W. G. Scholz

Molybdenum of high purity can be produced by direct dissociatiott of commercial molyhdenm disulfide in vacuo at 1600° to 1700°C (2910° to 3090°F). The Product is lower in oxygen than commercially available molybdenzdm powder. Analyses of ingots arc-cast from commercial molybdenum powder, hydrogen-re-cluced from animonium molybdate, and from thermally dissociated molybdenum disulfide indicate that the levels of chemical impurities in these ingots are similar. Equipment now in operation will produce 100-lb hatches of powder product. The paper describes development of processing equipment, control of processing varzahles, handling of the product, and evaluatiotl of the melal produced. MOLYBDENITE (molybdenum disulfide) can be decomposed by heat in the absence of oxygen to produce elemental molybdenum and sulfur, which is evolved as a gas. The temperatures required for the dissociation are above 1370°C (2500°F); the sulfur must be continuously withdrawn to permit the reaction to proceed to completion. This is accomplished by continuous evacuation of the thermal dissociation chamber and condensation of the gaseous sulfur in another part of the system. Cognizance of the fact that the dissociation takes place in two steps is important in controlling the process. Basically, the molybdenite dissociation process has two potential advantages as a method of produc- ing pure molybdenum: 1) The materials entering into the process contain little or no oxygen. Since the process is carried out in vacuum at high temperature, the quantities of interstitial oxygen, nitrogen, and hydrogen in the product should be very low. 2) The process is more direct than the commercia1 method of producing high-purity molybdenum. In the conventional process, molybdenite is roasted to molybdic oxide, the oxide is purified first by sublimation, then by conversion to ammonium molybdate, and finally, the molybdate is reduced in a hydrogen atmosphere (usually in two steps) to the metal lic molybdenum powder. This paper presents a description of the stages in scaling-up of the dissociation equipment and an account of attempts to evaluate the molybdenum produced by thermal dissociation, rather than a report of a fundamental study of the dissociation reaction. Since little has been written on the subject, it is appropriate, before detailing the development of the process, to review briefly the research that has been conducted over quite a period of years. LITERATURE SURVEY The first accounts of the possibility of thermal dissociation of the mineral molybdenite were re-

Jan 1, 1962

By D. W. Reed, R. L. Reed, Tracht

Laboratory experiments on the reverse combustion of tar sands in a linear adiabatic system have shown that a highly upgraded oil can be produced from an exceedingly viscous, immobile oil. The dependence on the air-injection rate of peak temperature, combustion-zone velocity, oil recovery, air-oil ratio, residual coke and oil, fuel burned and distribution of product gases is shown graphically. Eflects of initial temperature, oxygen concentration, oil saturation and heat loss are discussed. Experiments bearing on the coking properties of heavy oils are mentioned and some results exhibited. Field application of the process hinges on the existence of adequate air permeability and the rate of reaction under reservoir conditions. INTRODUCTION It has been established that oil can be recovered from underground reservoirs by means of at least two fundamentally distinct methods involving in situ combustion of a certain fraction of the oil. Characteristic of both of these known methods is the production of oil from one or more wells by means of hot gases formed when a high-temperature reaction zone is advanced through the reservoir. In both cases, the reaction zone is created by heating certain of the wells to a sufficiently high temperature prior to the introduction of air, and the zone is maintained and advanced through the reservoir by appropriate control of the air-injection rate. In the first of these methods, which is called "forward combustion",' the combustion zone advances in a direction which is generally the same as that of the air flow; whereas in the second method, "reverse combustion",' the combustion zone moves in a direction generally opposite to that of the air flow. Forward combustion, on the one hand, is an ideal combustion process in the sense that a minimum of the most undesirable fraction of the oil is consumed as fuel in the form of coke, a clean sand is left behind and generated heat is used as efficiently as possible. However, the applicability of forward combustion is limited. Since the products of combustion, vaporized oil and connate water must flow into relatively cold regions of the reservoir, there is an upper limit on the viscosity of oil which can be moved by this process in a practical and economical fashion.' On the other hand, it is characteristic of reverse combustion that the vaporized oil and water together with the products of combustion are produced through sand which is already hot and has had its mobile liquid content eliminated. This means there is no upper limit on oil viscosity; indeed, the oil may be an entirely immobile semi-solid. However, fuel for the process is an intermediate fraction of the original oil, and the most undesirable fraction remains on the sand surface as a substantial deposit of coke. Since this coked material is not burned during reverse combustion, it represents energy which is available for the production of oil but is not used for this purpose. It follows that one can expect economics to be somewhat less attractive with reverse combustion than with forward combustion. Nevertheless, it is a process which is designed for reservoirs where forward combustion is impossible and, as such, has become a subject of experimental and theoretical investigation. In this paper, only experiments made with tar sands are discussed. DESCRIPTION OF THE PROCESS We proceed, then, to consider the process of reverse combustion in greater detail. Fig. 1 illustrates a temperature profile defining a combustion zone which moves from right to left when air flows from left to right. In Zone 1, the temperature is the initial reservoir temperature, and the tar sand is as yet unaltered. This statement must be modified to the extent that physical properties of the oil may be changed by low-temperature oxidation at reservoir temperature. As air passes into Zone 2, which has been warmed by conduction, it assists in vaporization of the very light ends (if there are any), and oxidation occurs at a significant rate. In this region, there is almost no production of carbon monoxide or carbon dioxide because predominantly addition-type reactions take place with the formation of oxygenated compounds such as aldehydes and acids together with water. The hydrocarbon-enriched and slightly oxygen-depleted gas stream enters Zone 3 where

By Francis C. Krauskopf, Carl E. Swartz

Metallurgists differ considerably in their opinions regarding the effect, if any, of small amounts of iron pyrites, or other iron compounds on zinc sulfide ores during the roasting operation. As a result, the literature on this subject expresses many conflicting ideas. The ore, previously crushed to pass through a 1-mm. screen, dries in the roasting kiln, losing water up to 200° to 300° C. At 150° C. iron pyrites begin to lose sulfur. As the temperature increases, while the ore is passing to the hotter part of the furnace, the sulfur burns to sulfur dioxide, leaving the metals as zinc oxide and ferric oxide. These two substances then interact to form zinc ferrite, a compound, yellow brown in color, having the general characteristics of a spinel. Like magnetite, another spinel, zinc ferrite is insoluble in alkalis and dilute acids. As a result, when leached with 10 per cent. sulfuric acid solution, zinc values tied up in this compound remain behind History In the electrolytic recovery of zinc from its ores, the roasted ores are usually leached with a 10 per cent. sulfuric acid solution. When the zinc ore contains iron pyrites as an impurity in an appreciable amount, the actual yield of metallic zinc is much lower than a theoretical calculation would indicate. Further, losses of zinc are, in a rough way, directly proportional to the amount of iron pyrites or other iron compounds present. When the iron is present in the ore in an isomorphous relation to the zinc, as in the case of a marmatite, a greater amount of zinc remains insoluble than when present as a true pyrite or marcasite. Work on the insoluble residues obtained from leaching of the calcines shows that the zinc lost is intimately tied up in this residue. Some investigators have suggested a definite compound, such as zinc ferrite; others merely a mixture of zinc and iron compounds. As early as 1851, Pelouze(')' prepared calcium ferrite by fusion of calcium oxide and ferric oxide. Ebelman, 2) about the same time, prepared

Jan 1, 1928

By R. L. Bleifuss

Most pellets swell only slightly during reduction, but some swell so enormusly that their increase in size is termed catastrophic. Since catastrophic swelling produces irregularities in blast furnace operation, an understanding of the phenomenon is of practical as well as theoretical interest. Observations have shown that catastrophic swelling is characterized by the growth of a network of fine iron filaments. Evidence is presented to show that the growth of these filaments is promoted by the presence of calcium in the magnetite lattice of the original ore. During reduction, the limited mutual solubility of CaO and FeO produces an unstable condition that inhibits the uniform nucleation of metallic iron. Other elements in the magnetite lattice whose oxides are continuously soluble in FeO in the critical temperature range have no effect. Magmatic segregation or pyrometasomatic replacements are the most likely deposits to contain calciferous magnetite. Over the past few years there has been an increasing concern throughout the iron and steel industry over the tendency of pellets to swell during reduction. Although the tendency for swelling is only one of several attributes that determine the behavior of pellets in the blast furnace, swelling-reduction tests are now part of the normal evaluation procedure of many pellet consumers. During a swelling-reduction test, pellets display either the moderate increase in size known as normal swelling, or the enormous expansion known as catastrophic swelling. This paper is concerned with the origin and control of catastrophic swelling and how it is enhanced or inhibited by the presence of minor elements. Swelling Behavior The swelling behavior of pellets during reduction is indicated in Fig. 1. The lower curve represents normal swelling and the upper curve catastrophic swelling.' During the initial stages of reduction, that is, up to about 20-25% reduction, the two curves are considered to be equivalent. Beyond this point normal pellets undergo a gradual decrease in size with increased reduction. By contrast, pellets which exhibit catastrophic swelling show a second dramatic expansion between 25 and 70% reduction. The initial normal swelling develops as the hematite of the pellet is successively reduced to magnetite, and then to wustite. Work by Edstrom' and others has shown that the reduction of hematite to magnetite is accompanied by a 25% volume increase, whereas the magnetite to wustite stage shows a volume decrease. The volume increase overlaps the wustite field because magnetite is formed simultaneously with the wustite during topochemical reduction of the pellet. The catastrophic expansion is clearly related to the wustite, to

Jan 1, 1971

By L. D. Fetterolf

The New Jersey Zinc Zompany operates at Depue, Illinois, an integrated zinc smelting plant using tie vertical retort reduction process. The overall operation comprises green concentrate roasting, sintering, vertical retort smelting and metal refining. In the roasting operation, the fine concentrate is pelletized, the dried pellets fluidized and autogenously roasted with air in a “fluid column” with minimal formation of dust requiring recirculation. The roasted pellets and any associated roaster dust are agglomerated in a rotating drum and laid down, in combination with coal for fuel, on a Dwight-Lloyd sintering machine which converts to a semi-fused mass - a physical state more suitable for vertical retort smelting. The smeltins plant of 27 vertical retorts rated at 8 T zinc each per day on average requires the following major processing steps - mix preparation and briquettine, briquet coking, vertical retort reduction, vapor condensation and slab casting of metal. A portion of zinc production is converted to 99.99+ percent purity by boiling and fractional distillation in columns consisting of externally heated, superimposed trays of high-conductivity refractory.

Jan 1, 1970

By H. M. Stewart, R. A. Grange

MANY steel parts may crack if quenched directly into a bath near room temperature, but not if quenched at a temperature just above the range where martensite forms and then allowed to cool slowly to room temperature. This latter procedure, which is the basis for such modern hardening techniques as "martempering " and "isothermal quenching," may entail some sacrifice in depth of hardening but very little, if any, in intensity of hardening. In planning such treatments, it is necessary to know the upper limit of the martensite range, and often desirable to know the proportion of martensite that would form on cooling to any lower temperature; furthermore, the tendency of a particular steel to crack when quenched is unquestionably associated with the temperature range of martensite formation, and consequently knowledge of this range aids in selecting the optimum composition for a given application. Certain puzzling phenomena associated with the properties of quenched and tempered steel may be at least partly clarified as the manner in which martensite forms is more fully under- stood. Information on the temperature range of martensite formation, particularly with respect to how much martensite results from quenching to a given temperature, is lacking for most commercial types of carbon and low-alloy steel. These considerations led us to study martensite formation in 14 carbon and low-alloy steels. The resultant data may be directly used in the following ways: (I) for selecting the lowest quenching temperature at which no martensite will form; (2) for selecting the highest quenching temperature at which virtually dl marten- site will form, thereby avoiding quenching to an unnecessarily lower temperature with attendant danger of cracking; and (3) in producing a mixture of tempered marten- site and bainite, which in high-carbon steels has been found to possess somewhat better ductility than tempered martensite, yet does not require the full transformation time necessary for a completely bainitic (austempered) structure. PART I. OBSERVATIONS OF MARTEN- SITE FORMATION IN FOURTEEN CARBON AND LOW-ALLOY STEELS Transformation of austenite to pearlite or bainite can be conveniently studied by observing the change that occurs over a period of time at constant temperature; such studies are the basis of the isothermal transformation diagram (S-curve). This isothermal technique is not applicable to martensite formation, which occurs within a time interval too small to measure, at least by any ordinary means. For all practical purposes, therefore, martensite may be regarded as forming only during cooling and not during a period of time at constant temperature. As austenite is cooled below

Jan 1, 1946

By Jo. E. Sheridan

The Dawson coal-mines are owned aid operated by the Stag Canon Fuel Co., of which Dr. James Douglas is President and E. L. Carpenter general manager. The property is situated in Colfax county, N. M., and the openings now in operation are in townships 28 and 29 N R. 20 E., and township 28 N E. 21 E., shown in Fig. I. The mines are part of the southern end of the Raton coal-field, which extends north into Colorado and embraces many coal-camps of the Trinidad section. II. Geology. Geologically, the coal-measures, commonly known as the Laramie series of the Cretaceous system, have x thickness of about 800 ft. in the vicinity of Damson. The coal makes an excellent coke, and, according to some authorities, its coking properties are due to the action of intruded sheets and sills of igneous rock, the sheets occasionally thickening into masses resembling laccoliths, at such places making nearer approach to the coal and sometimes producing small areas of natural coke. There are but few dikes throughout the entire southern portion of the field and little or no faulting along the dikes. In some parts of this great coal-field the intrusive sheets are far removed in the green shales below the coal-measures, and are so much altered as to be difficult of identification. There is but little disturbance of the strata throughout the Raton coal-field in as far as it extends into New Mexico. There are two workable seams in the coal-measures, and two or three smaller coal-seams, ranging from 1 to 2.5 ft. in thick-

Jan 1, 1910

By A. W. Peake, F. O. Prior

Considering the great advance in the development and application of electricity, it is not strange that eventually a big field for its use has been found in oil-field operations. So far as is known, the first electric drive in oil-field operations was in the Russian field of Baku in 1900. The first application in this country was made by the South Penn Oil Co. near Folsom, West Va. in 1903. In 1916, electric power was first used in the Burma fields of India for drilling and pumping. Between 1916 and 1922, The Empire Gas & Fuel Co. made the first large electrical installation in the Mid-Continent fields. But although the first application was made 27 years ago, it is only within the last 10 years that oil companies have begun to look upon its use with much favor. Within the last few years, there has been a steady increase in the use of electricity in the oil fields. The first application of electricity for oil-field operations in Wyoming was in the Lander field in 1919; the second was in 1924 in Salt Creek; and the third, and last to date, was made by the Continental Oil Co. in the Big Muddy field during 1926. Lander Field The electrification of oil-field operations in Wyoming was initiated by J. W. Steele, superintendent of the Producers & Refiners Oil Corpn., in the Lander field in 1919. At that time, 32 wells were being pumped from five band-wheel powers, with oil engines as the prime movers. Eight barrels of fuel oil were used for power per day and at the price of 90 c. per bbl. the fuel bill was $36 per day. It was decided to try a 15 to 35-hp. oil-field motor on one of these powers. Electric power was generated with steam at the old Wind River refinery station. This test was so successful that in 1920 all five powers were equipped with 15 to 35-hp. oil-field motors, the power being obtained from the Sinks Canyon hydroelectric station. Four of these powers pumped wells at an average depth of 1450 ft., and the fifth pumped wells at an average of 2100 ft. In 1920, the average production per day from the 32 wells was 325 bbl. The power bill on the

Jan 1, 1928