Search Documents

By Klaus Schwerdtfeger

The equilibria in the Cr-N system have been investigated in the temperature range 1100° to 1310°C by reacting chromium powder with Nz-Hz gas mixtures. The solubility of nitrogen in chromium in equilibrium with chromium subsitvide ("Cr,N") is given by Chromium subnitride is nonstoichiotnetric; its nitrogen content is always less than that corresponding to the formula CrzN. The lattice paranzeters of quenched samples have been measured; c, and a. parameters are found to increase with increasing nitrogen content. The growth rate of the subnitride layer on chromium plates was measured by a thermogravimetric technique, using a silica spring balance. The self-diffu-sivity obtained from the theoretical analysis of the parabolic rate constant is found to decrease with increasing nitrogen content, i.e., with decreasing vacancy concentration in the nitrogen sublattice. The intrinsic nitrogen diffuivity is derived from another series of rate measurements using "CrzN" plates; the intrinsic diffusivity, DN = 3.2 X 10-a cmZ sec-' at 1200 C, is found to be essentially independent of- the subnitride composition. The concentration gradient was measured in a chromium subnitride layer by the X-ray method and found to be consistent with the derived diffusivity value. TWO chromium nitrides are known to exist:' the nonstoichiometric subnitride "CrzN" and the nitride CrN. In the present work the kinetics of the formation of chromium subnitride from chromium and nitrogen have been investigated at 1100" and 1200°C. In additional experiments the relevant equilibria have been measured. The data are used to evaluate the diffusivity of nitrogen in chromium subnitride. Since chromium nitrides are often found in chromium-containing steels, the results are expected to be helpful in the interpretation of the chemical reactions between chromium steels and nitrogen. Equilibria in the Cr-N system have been determined by several investigators.2"3 The rate of nitriding of chromium was measured by Arkharov et a1 .' in ammonia in the temperature range 800" to 1200°C. The parabolic rate law was observed. Due to the undefined nitrogen activity of the ammonia atmosphere, it is dif- ficult to interpret these rate data theoretically. An additional difficulty arises from the fact that the two-layer scale consisting of CrN and "Cr2N" was formed at the temperatures below 1030°C. The rate of nitriding of technical chromium (95 pct) was measured by Zaks in nitrogen at -1 atm in the temperature range 800" to 1300°C. EXPERIMENTAL METHODS The chromium samples were reacted with Nz-HZ gas mixtures in a vertical tube furnace, wound with Pt-10 pct Rh resistance wire. The gas-tight reaction tube was of high-purity recrystallized alumina. In nitrogen solubility measurements the nitrogen content of chromium was determined by the Kjeldahl method, on samples quenched in the cold part of the furnace. The nonstoichiometry of the subnitride and the nitriding rates were measured thermogravimetrically using a sensitive (+0.1 mg) silica spring balance. For the equilibrium measurements samples of 1 g of chromium powder contained in high-purity alumina crucibles were used. In order to remove most of the oxygen and nitrogen impurities from the chromium, the samples were initially annealed in purified hydrogen until a constant weight was obtained. The chromium plates (approximate dimensions 2 by 1 by 0.08 cm) used for the rate measurements were machined from ingots obtained by arc-melting of iodine-processed chromium. According to manufacturers' specifications the purity of the chromium powder was 99.9 pct Cr and that of the iodine-processed chromium 99.99 pct Cr. Our own spectroscopic analysis of the chromium powder yielded 0.02 pct Fe, 0.05 pct Mn, 0.05 pct Si, and 0.02 pct Ti as major impurities with all the other detectable elements below 0.005 pct. The nitrogen partial pressure of the gas phase was controlled by mixing prepurified hydrogen and nitrogen with constant pressure head capillary flowmeters. Oxygen and water vapor were removed from the mixed gas by passing it through columns of platinized asbestos (450°C) and anhydrone. The gas flowed upward in the furnace with flow rates of 300 to 500 cu cm per min (25"~). Gas tightness of the furnace system was ensured by pressure checks at regular intervals. The furnace temperature was controlled electronically in the usual manner. The reported temperatures were measured with a Pt/Pt-10 pct Rh thermocouple and are estimated to be accurate within ±$C The X-ray measurements were made with a Debye-Scherrer camera and a diffractometer using chromium radiation {\Ka = 2.29092A). EQUILIBRIUM MEASUREMENTS The experimental results of the equilibrium measurements are contained in Tables I to In. Fig. 1 shows the solubility of nitrogen in solid chromium in the temperature range 1100" to 1310°C. In Figs.

Jan 1, 1968

By Ancel St. John

DURING a session on coal and coke at the February, 1926, meeting of the American Institute of Mining and Metallurgical Engineers, the writer called attention to the important work on the X-ray analysis of coal1,2 being carried on in England by C. Norman Kemp and his associates. This aroused so much interest that a paper on the subject was requested for the October meeting. It has seemed advisable to make this paper a preliminary survey of the present status in the application of X-ray methods to coal problems and to follow it from time to time with further articles as the art develops. A survey of this sort naturally divides itself into two parts, radioscopic analysis of the distribution of constituents through the body of the coal, and diffraction analysis of the state of association of the elementary components. In this article the subject matter concerning radioscopic analysis has been drawn almost entirely from the writings of Kemp and his associates and the illustrations have been specially furnished by him. It is a pleasure to record here a great indebtedness for this courtesy and cooperation. The subject matter and illustrations concerning diffraction analysis are taken from the author's unpublished researches.

Jan 10, 1926

By Roland de Wit

Conclusions reached in a paper by weertmanl are amplified in a mathematical and graphical way. It is shown that in a stressed crystal a straight dis-location may be in a position of unstable equilibrium with respect to helix development, and how a small perturbation may start the dislocation off on its helical path. Helix development occurs by diffision; bulk diffusion is necessary for development from a screw, but core diffision is sufficient for development from an edge dislocation. For a mixed dislocation helix development can take place by core diffusion if the helix also climbs; a diffusion reversal takes place when the slope of the helix equals the slope of the Burgers vector. The work done on a crystal by the external forces is graphically shown to be consistent with the direction of motion of the dislocation in helix development. Finally a detailed mechanism for tangle formation from helices is presented. In the course of helix development a glide situation may be reached where a segment of each helix loop lies in a slip plane in which it can expand by glide. Thus is it visualized how a helix can deteriorate into a tangle. A paper by weertmanl proposes dislocation-tangle formation by a helical dislocation mechanism. The present paper amplifies Weertman's arguments in a mathematical and graphical way and presents some further ramifications of the proposed model. The importance of dislocation tangles is discussed in Weertman's paper and the references cited therein. The mechanism of their formation is not yet understood. Weertman proposes that in cold-worked crystals conditions exist suitable for the conversion of straight dislocations into helices and subsequently into tangles. Helix formation occurs by a diffusion process and Weertman proposes that at low temperatures only core diffusion is important. The present paper necessarily repeats some of Weertman's work. Since the mathematical development and notation used are slightly different from his, this was thought necessary for clarity. GEOMETRY OF THE HELIX weertman2 has shown that the equilibrium form of any dislocation line is a helix if it is assumed that the energy per unit length (line tension) of the dis- location is constant. For the special case that no external forces act on the dislocation, the helix reduces to a straight line. We shall assume in this paper that the dislocation has a helical form even when it is not in equilibrium. The parametric equation of a helix is, see Fig. l: where a is the radius of the cylinder tangent to the helix, and 270 the pitch of the helix. The pitch is related to v, the number of turns per unit length (along the axis) by the relation: When a = 0 Eq. [I] gives a straight line in the z direction. The growth of a straight dislocation into a helix is now described mathematically by letting a vary from zero to its final value. The tangent to the helix is given by where is the path length along the helix. This gives the direction of t and since its magnitude is unity we must have So that dcp/ds = (a2 +p2)-"'. The curvature of the helix is given by where n = -(cos + sin) is a unit vector normal to the helix. Note that the vectors k and n always point toward the axis of the helix, Fig. 1. FORCE ON THE HELIX The external force which makes the straight dis-

Jan 1, 1963

By H. Groeneveld, C. A. Connally, P. J. Hoenmans, J. J. Justen, W. L. Mason

A miscible displacement pilot using a slug of LPG driven by separator gas was conducted in the Cardiurn reservoir of the Pembina field. The injection pattern was a 10-acre, inverted, isolated five-spot. Upon completion of the LPG-gar phase, an experiment was conducted using a slug of water followed by gas. Calculated performance of the pilot is compared with actual performance. Equations are developed to calculate the distribution of LPG into zones of varying permeability, to estimate the progress of the flood at different times in the various zones and to estimate gas rates after breakthrough. The analysis indicates that permeability stratification was a dominant factor in controlling oil recovery and that oil was completely displaced from the swept pore volume. The results of the pilot indicated that miscible flooding is a practical means of pressure maintenance in this reservoir. The total recovery from the pilot area was good in spite of the early breakthrough of LPG. The effects of stratification were reduced by injecting a slug of water into the partially swept reservoir. INTRODUCTION The Pembina field,' located in Alberta, is the largest oil field in Canada and one of the largest in the North American continent. The reservoir is a stratigraphic trap producing from the Cardium sand. Neither bottom water nor free gas has been found. The recovery of oil by the natural depletion mechanism has been estimated at 12.5 per cent. Pressure maintenance studies of various areas have indicated that the recovery can be increased 21/2 times by water flooding, and a large area of the field is presently under water flood. However, reservoir studies of the North Pembina area indicated that miscible flooding might be competitive with water flooding. A pilot test was conducted to evaluate the performance of a miscible flood. A 10-acre, inverted, isolated, five-spot pattern was selected for the pilot. The pattern area was large enough to minimize wellbore fracturing effects and contained sufficient oil to provide significant working numbers. The performance of each of the four producers could be evaluated individually and compared. In the event of breakthrough in one direction, the effect would be isolated from the other producers. The use of a single injector minimized the volume of LPG required, and, because of the high mobility of gas, one well was sufficient to inject the necessary daily volume to replace the high rate of production. With four producers, the test could be completed in time for results to be evaluated, additional engineering studies to be made and a unit to be formed before the reservoir pressure in the North Pembina area declined below the bubble point. The pilot was located in an area developed on staggered, 80-acre spacing. The injection well was drilled at a regular location, while the four producers were drilled 467-ft north, east, south and west of the injector. Each quadrant and its associated producer were identified according to their direction from the injector— that is, north, east, south or west. The eight surrounding producers on 80-acre spacing were shut in to isolate the pilot area and provide for reservoir pressure observation. The pilot wells were completed using permanent-type completion techniques. After coring, casing was run through the pay section and cemented. Inside 51/2-in. casing, 2 1/2-in. tubing was hung. The wells were perforated opposite the Upper Cardium sand and lightly fractured. Fracturing volumes, rates and pressures were low to minimize the extent of the fractures. The fracturing treatments average 1,000 lb of 20-40 mesh sand in 700 gal of a low fluid-loss sand-carrying agent. Feed rates and wellhead fracturing pressures averaged 5.5 bbl/min at 2,535 psig, respectively. After fracturing, the productivity index was measured in each of the five pilot wells. The average PI of the four producers was 0.41 BOPD/psig drawdown. The measured PI'S were approximately the same as PI'S calculated from core analysis data, indicating that the fracturing treatments were just sufficient to overcome

By Roy R. Weil, John A. Dziubek

This paper discusses the use of computer modeling, data manipulation, and mapping of three multi-seam coal properties in the Appalachian coal basin. Each case history represents a slightly different application of computer usage for estimation of reserves and planning surface mine sequencing. This practical use of computers demonstrates the suitability of data processing for normal evaluation of coal properties.

Jan 1, 1983

By Henry Fay

THE erosion of guns is a complex problem which can be solved only by a detailed study of all the factors involved. In the present paper it is proposed to submit the results of observations and experiments which have extended over several years. Certain facts have been established and preliminary reports have been published.' Conclusions have been reached since then which, it is believed, are worth presenting for the purpose of promoting discussion, and with the hope that ultimately the whole truth will be known. The particular phase of the problem which will be presented here is the hardening of the inner surface of the gun tube. It has been known for a long time that after firing a large caliber gun for some time, the surface of the metal becomes hard and brittle, cracks, and wears away.2 The character of this phenomenon may be learned by an examination of some results which are typical, obtained from a detailed study of a 12-in. gun. The gun was trepanned and rings representing various sections of the gun were cut out for examination. The first ring represented the metal at the muzzle end, and the other rings were removed at approximately 120, 240, 325 and 337 in., respectively, toward the breech end. The appearance of the surface of the metal in the different sections is shown in Fig. 1. The greatest amount of wear and maximum amount of hard surface layer was found in section marked E, which is nearest the powder chamber and at the beginning of the rifling; the maximum amount of cracking in D; the maximum amount of copper deposition in C. Section B showed heat cracks on both lands and grooves, and section A showed heat cracks on the driving edge of the lands only. There was much flow of metal in both sections E and D, and there was progressively less effect noticeable toward the muzzle end. The polished cross-section of these same pieces is shown in Fig. 2. The

Jan 12, 1916

By D. J. Carney, R. R. Burt, E. J. Whittenberger

Hardenability (multiplying) factors for carbon, mongonese, silicon, chromium, nickel, and molybdenum have been developed for hypereutectoid low-alloy steels in which bainite is the first subcritical transformation product. These factors permit the calculation of 95, 80, and 50 pct martensite hardenability from chemical composition when steels with spheroidized structures are quenched from 1475°, 1525°, and 1575°F. The strong contributions to hardenability of the less expensive elements, silicon and manganese, suggest their use to obtain additional hardenability in hypereutectoid low-alloy steels. DURING the past decade a number of investigators'"11 have carefully developed information which permits calculation of the hardenability of medium -carbon low-alloy steels from chemical composition and grain size. These data have been especially valuable in developing less costly low-alloy steel compositions with equivalent or Improved

Jan 1, 1957

By Noel H. Stearn

When the Age of Machinery was suddenly thrust upon civilization about the beginning of the 19th century, an unprecedented demand for mineral resources sprang up. This demand brought about the rapid development of the known ore deposits and the discovery of such other deposits as could be encountered by energetic and canny prospectors. Thus in the countries now reasonably accessible nearly all orebodies have been located except those which are totally concealed even from the eyes and "senses " of experienced and expert prospectors. The high rate of exhaustion of known ore deposits and the necessity of looking farther and farther ahead for raw materials as a matter of insurance on the stupendous capital outlays involved in mining, development, and conversion operations, have resulted in exceptional activity in three different fields of effort. The first is purely geographic. Prospectors are now penetrating the few hitherto inaccessible regions in the hope of stumbling upon exposed ore deposits or locating visible indications of their presence. The second is chemical. Industrial chemists and metallurgists are seeking to facilitate the exploitation of lower grade ores or to find methods of recovering valuable metals from common substances. In the third field of effort lie the activities of the economic geologist and the mining engineer, who endeavor to locate concealed ore deposits which would remain hidden from the prospector no matter how expert or conscientious he might be. Obviously the task which such a man must face is both exacting and indefinite, and the tools which he has heretofore been permitted to bring to it are, for the most part, abstract—a knowledge of certain fundamental principles and processes involved in the origin, occurrence, structure, and distribution of deposits of natural resources and of the rocks which form the environments of those deposits; and a process of reasoning by analogy supplemented by the use of the diamond drill, or such artificial exposure as the test pit, trench, shaft, or tunnel.

Jan 1, 1929

By E. H. Bunce, E. C. Handwerk

The inherent difficulties of zinc smelting arise from the fact that metallic zinc is volatilized at the reducing temperature of zinc oxide and thus is liberated in the form of a vapor. This vapor must be subsequently condensed to obtain metallic zinc, first in molten and eventually in solid form. Zinc vapor is sensitive to oxidation not only by air but by combustion gases containing carbon dioxide. It is, therefore, necessary to carry out both the reduction and the condensation operations in a closed system consisting of an externally heated muffle with attached condenser from which extcrnal oxidizing agencies are excluded. However, the reoxidation of zinc vapor cannot be entirely prevented by excluding external sources of oxidation. Internal sources of oxidation are necessarily present when oxidic zinc ores are reduced by a carbonaceous reducing agent. The reduction reactions themselves involve, first, the production of carbon monoxide in an amount at least equal in volume to the zinc vapor produced in the reaction, and, second, the formation of carbon dioxide. Not all of the carbon dioxide is reduced again to carbon monoxide by the excess carbon in the time available, and the slightly oxidizing condition, which results, seriously affects the efficiency of the condensation of the zinc vapor to the metallic state. In the past the difficulties arising from these causes have limited practical zinc smelting on an industrial scale to the use of small retorts equipped with small condensers. The retorts had to be small, because a closed refractory container capable of excluding oxidizing gases from the heating chamber surrounding the retort could not be built in large dimensions. The size was also limited because ordinary refractories when thin enough to conduct heat readily are not capable of sustaining a heavy load of charge at high temperature. Moreover, a loose charge of zinc ore and carbonaceous reducing material such as fine anthracite coal or coke breeze is a poor conductor of heat, thus limiting the cross section of the retort. The operation of these small retorts requires arduous

Jan 1, 1937

By Henry M. Howe, W. P. Barba

When this country went into the war, but two concerns, The Bethlehem Steel Co. and The Midvale Steel and Ordnance Co., knew how to make steel fit for great cannons and at these concerns there were relatively few men who knew the whole art. Fortunately, certain of these men put their knowledge at the service of the Government, and proceeded to instruct the metallurgists at the arsenals and at various steel works. Doctor Howe, then chairman of the Engineering Division of the National Research Council, suggested that this work might be facilitated, and the number of effective gun-steel makers thereby increased, if a detailed description of the best practice could be written, giving the reasons for the various steps, and issued with the endorsement of a committee composed of those who were evidently the most competent authorities. It was thought that something would be gained by clarification of the subject, and something by the eminent authority of the members of the committee. To that end, the Engineering Division appointed a committee, consisting of the gentlemen whose names follow, to mention on1y those who retained their connection with it. At this time there were serious difficulties in the manufacture, for the Government. of aircraft and high-speed engine crankshafts, of certain ordnance forgings, and of shells for both the Army and Navy. This Committee was asked to study and report upon these, with a view to betterment of practice. There were indications that the source of some of the difficulties went back to the melting of the steel and the production of the ingot. Hence, the committee first studied steel melting and ingot production, in order to guide the wartime manufacturers to an even larger percentage of useful production from the steel initially melted. Committee on Steel Ingots W. P. Barba, chairman, Ordnance Dept., U. S. A. (formerly Vice Pres. & Gen. Mgr., Midvale Steel Co., Philadelphia). George K. Burgess, Chief of Division of Metallurgy, U. S. Bureau of Standards, Washington, D. C. Henry M. Howe, Then Chairman Engineering Division, National Research Council.

Jan 1, 1922

By W. P. Barba, Henry M. Howe

When this country went into the war, but two concerns, The Bethlehem Steel Co. and The Midvale Steel and Ordnance Co., knew how to make steel fit for great cannons and at these concerns there were relatively few men who knew the whole art. Fortunately, certain of these men put their knowledge at the service of the Government, and proceeded to instruct the metallurgists at the arsenals and at various steel works. Doctor Howe, then chairman of the Engineering Division of the National Research Council, suggested that this work might be facilitated, and the number of effective gun-steel makers thereby increased, if a detailed description of the best practice could be written, giving the reasons for the various steps, and issued with the endorsement of a committee composed of those who were evidently the most competent authorities. It was thought that something would be gained by clarification of the subject, and something by the eminent authority of the members of the committee. To that end, the Engineering Division appointed a committee, consisting of the gentlemen whose names follow, to mention on1y those who retained their connection with it. At this time there were serious difficulties in the manufacture, for the Government. of aircraft and high-speed engine crankshafts, of certain ordnance forgings, and of shells for both the Army and Navy. This Committee was asked to study and report upon these, with a view to betterment of practice. There were indications that the source of some of the difficulties went back to the melting of the steel and the production of the ingot. Hence, the committee first studied steel melting and ingot production, in order to guide the wartime manufacturers to an even larger percentage of useful production from the steel initially melted. Committee on Steel Ingots W. P. Barba, chairman, Ordnance Dept., U. S. A. (formerly Vice Pres. & Gen. Mgr., Midvale Steel Co., Philadelphia). George K. Burgess, Chief of Division of Metallurgy, U. S. Bureau of Standards, Washington, D. C. Henry M. Howe, Then Chairman Engineering Division, National Research Council.

Jan 1, 1922

By Earl Bardwell

THE structural relations existing between cuprous oxide and copper -were first systematically studied by Heyn1', who suggested that a study of the microstructure of refined copper might be substituted for the analytical methods in vogue for determining the oxygen content of copper coming from the refining furnace. Hofman, Green and Yerxa,2 in their paper A Laboratory Study of the Stages in the Refining of Copper, working along the lines suggested by Heyn, showed that a study of the microstructure could be made to yield a correct estimate of the oxygen content of the specimen of refined copper under examination. In order to determine the oxygen content of the specimen of refined copper under. examination a photomicrograph was first made. From the relative areas of copper and eutectic, the percentage of cuprous oxide and the corresponding percentage of oxygen were then readily calculated. It was found that the values for oxygen thus obtained corresponded closely with the analytical results. With the idea of utilizing this method of determining the oxygen content of each charge dipped from the refining furnaces at the Boston & Montana Reduction Plant, the physical testing laboratory was equipped with suitable apparatus for carrying out the work. It may be of interest to describe certain of the methods which have been worked out in this connection and give such data as have been obtained bearing on the effect of the oxygen content of refined copper upon its conductivity. Apparatus.-For the benefit of those who may be unfamiliar with metallographical apparatus and methods and may be interested to know what equipment is required, a few words with regard to the apparatus is in place at this point.

Jan 7, 1913

By Robley D. Evans, Gerald L. Schroeder

Advanced techniques for control of radon (Rn) daughter product concenrrations (working levels, WL) in the uranium mines are discussed. Understanding the physical laws which govern the flux of radon into a mine, the growth and decay of the radon daughters, and the particulate nature of the daughters when suspended in air allows ventilation personnel to improve the quality of mine air with no increase in ventilation rate. The task of controlling, in a mine atmosphere, the short-lived nuclides produced in the decay chain of radon is a unique problem and as such should be approached with ventilation techniques specific to the problem. For most mines this has not been the case. Rather, procedures for removing these airborne radioactive nuclides have been borrowed directly from ventilation experience in mines where dilution ventilation was the traditionally accepted approach for air purification. With radon daughter products, this has often led to frustrating difficulties and expense. Primary origin of the airborne radioactivity is the a-ray-emitting noble gas, radon (222Rn, Rn), a nuclide formed by the decay of radium (226Ra, Ra). Radon, being a gas, may escape from its parent crystal and diffuse through the parent mineral into the interstices of the rock body. In a sandstone structure, about 20% of all the radon formed may find its way into the interstices of the rock. If a cavity such as a mine is nearby, the radon may diffuse through the rock interstices into the mine. While radium is usually highly concentrated in uranium ores, it is also found in varying concentrations in all minerals. Radon is therefore present in all minerals. In normal glacial till, the equilibrium interstitial radon concentration often equals 5000 pCi (picocurie, also uuCi) Rn per liter of pore volume.' In normal granitic rocks, the interstitial radon concentration often approaches 30,000 pCi per 1. Considering these typical, high-radon concentrations, radioactivity from airborne of daughter products is a potential problem unique not only to the uranium mining industry and should be considered as a potential hazard in all underground environments.

Jan 1, 1970

Paper withdrawn from publication September 8,1977, after book was printed. Pages 258.272 are therefore omitted.

Jan 1, 1977

By N. A. Stockett

SOUTHEAST Missouri is the largest and oldest lead-producing district in the United States. For the year 1941, the statistical picture of pig-lead production, stated in short tons (partly estimated by the Engineering and Mining Journal) is as follows. [Tons World production 2,000,000 United States production 460.000 Southeast Missouri production 242,000] The consumption of primary lead in the United States in 1941 was approximately 900,000 tons, or almost double the country's production. The largest previous year's consumption in the United States was 718,000 tons, in 1926. The largest quantities of lead are used for cable sheathing, storage batteries and white lead. During 1941 tetraethyl lead for auto and aviation gasoline consumed 50,000 tons of lead. The entire lead production of Southeast Missouri is now mined by the St. Joseph Lead Co., whose dominant position as the largest producer in the United States of lead directly from ores is best shown by the fact that in 1941 it produced approximately 31 per cent of the lead production of the United States from its mines in southeast Missouri, where 22,000 tons of ore, averag¬ing over 3.00 per cent lead, is mined per working day. It is known that lead was mined at Mine La Motte, Madison County, Missouri, by Renault in 1723. Other white men and Indians probably did some mining prior to that time. Since 1865, the recorded production to Jan. 1, 1942, shows that the St. Joseph Lead Co. and the various other companies that have operated in St. Francois County mined lead ore, which, after milling and smelting losses produced 5,00,000 short tons of pig lead. About 95 per cent of the present lead production of Southeast Missouri is mined in St. Francois County. The northern part of this area is 60 miles south of St. Louis. The remainder of the lead is obtained at Mine La Motte, about 25 miles southeast from the center of the producing area in St. Francois County. PROSPECTING In this district, most of the ore is discovered by surface and underground diamond drills and by prospect drilling underground with rock drills. Each 2-ft. length of the cuttings from these Jackhamer prospect holes is assayed for lead. These holes are marked and the records are entered on maps. It has been found that close drilling--100-ft. centers of holes, and sometimes less-is necessary in order to locate most of the smaller commercial ore bodies, many of which previously had been missed by drilling the areas with holes spaced 200-ft. centers or more.

Jan 1, 1943

By R. F. Mehl, C. S. Barrett, A. H. Geisler

THE studies of the mechanism of precipitation and of the resulting property changes in aluminum-silver alloys1-3 have presented some new concepts of the aging reaction-concepts that may be fundamental in establishing a complete quantitative theory of age-hardening. With both aluminum-copper and aluminum-silver alloys, thin platelike aggregates form parallel to the Widmanstätten planes of precipitation.1,4 These platelets grow in lateral dimensions and in thickness with aging time until they are thick enough to produce an X-ray diffraction line pattern. Their structure is that of a transition lattice which is coherent with the matrix, since the atomic spacings in the matrix and the precipitate are the same on each side of their common interface.2,4 The equilibrium precipitate forms later from and at the expense of the transition lattice. Since age-hardening occurs during the formation and growth of the transition lattice, the major contributor to the hardening no doubt is the stress condition in the matrix resulting from the matrix holding the precipitate in the coherent condition. The development of these stresses also appears to be responsible for an increase in the electrical resistance superimposed on the normal decrease resulting from a change in the concentration of the matrix during aging.3 The two consecutive reactions constituting the aging process are accompanied by characteristic microstructural alterations. The initial precipitation process results in the formation of a Widmanstätten figure, while the later transformation of the transition lattice to the equilibrium lattice is accompanied by a coalescence, in the case of aluminum-copper alloys,5 and by the appearance of light areas at the grain boundaries with aluminum-silver alloys showing a structural rearrangement of matrix and precipitate.3 This latter reaction is similar microscopically to the so-called "discontinuous precipitation." Possibly discontinuous precipitation is a process that often if not always follows true precipitation of a coherent lattice and during which the transformation of the coherent transition lattice to the equilibrium lattice takes place accompanied by matrix recrystallization.3 EXPERIMENTAL PROCEDURE The alloys were made using 99.97 per cent Al or distilled magnesium, with

Jan 1, 1943

By G. S. Rice

The subject of dust explosions in coad mines first appears in the Transactions of this Institute following the first great mine disaster that happened in…

Jan 1, 1915

Jan 1, 1969

By H. G. Moulton

THE INCREASING scale of mining operations over the past decade, particularly in connection with the exploitation of large bodies of comparatively low-grade copper ores, has made necessary the study of the behavior of rock under failure. When extractions of as high as 40,000 tons a day are reached in steam-shovel operations and as high as 20,000 tons per day in underground mining operations, it is evident that excavations soon become of such size that the behavior of the rock will often be dependent on fundamental principles applicable to more or less homogeneous materials under stress, rather than on weathering or local planes of weakness. In the ordinary rock excavations encountered in civil-engineering practice, such as excavations for subways, highways, railroads, etc., rock faces are not carried to depths sufficient to develop any pressures, or consequently any failures, except those due to loose masses resulting from local planes of weakness. When, however, orebodies whose tonnage is measured by hundreds of thousands are to be extracted by steam-shovel operations in open pits, it is necessary to determine if possible in advance the slopes that the sides of the pits will assume, for these slopes influence the shape of the excavations and thereby the amount of ore that may be extracted by the open-pit method. When large orebodies are mined underground at depths of 300 to 500 ft. (91 to 152 m.) by caving methods, the surface subsiding as the ore is withdrawn, it is necessary to determine in advance the outermost limits of fracture in the subsiding surface, for on the delineation of these limits depends the location of surface improvements, mills, smelters, etc. and also the location of development work, such as hoisting shafts, main haulage levels, and all other underground openings that must remain undisturbed during the period of ore extraction. Heretofore, in civil-engineering practice, it has been assumed that earth and rock behave differently in failure. For the calculation of earth

Jan 2, 1920

By N. A. Gokcen

The construction and operation of a simple and accurate vacuum-fusion apparatus are described in detail. Absolute accuracy of the oxygen analysis has been determined by the reduction of oxides weighed to 20.01 mg. The Bureau of Standards steel samples have been analyzed repeatedly, and their inadequacy for the acceptable range of oxygen is presented. The limits of interference of manganese, aluminum, and titanium, and the effects of tin and water-cooling of the furnace tube have been investigated in detail. ANALYSIS by the vacuum-fusion method consists of melting a sample in a degassed graphite crucible under high vacuum and extracting oxygen as carbon monoxide, and nitrogen and hydrogen as gaseous elements. The resulting gas mixture is analyzed for its constituents, from which oxygen, nitrogen, and frequently hydrogen may be determined within 1/2 hr or less. The history and summary of methods1-4 and extensive reviews of literature'.' for the determination of gases in metals have been published in detail. The foundation of the modern vacuum-fusion method of analysis was laid by Jordan and Eckman,11 and Oberhoffer and his associates.1, 10 Diergarten,11, 12 Meyer,13 Thanheiser et al.,14, 15 Ericson and Benedicks,16 Ziegler,17, 18 Sloman,16-23 Thompson et al.,24 and later many others contributed to the improvement, accuracy, and limitations of the method. In some investigations, however, the limitations of the procedure and the errors involved in the analysis require further critical examination and evaluation. In many apparatuses, lunnecessarily complicated and cumbersome features and elaborate precautionary measures do not have conclusive advantages. The purpose of this invest:igation was, therefore, a) to construct a very simple and accurate apparatus, b) to determine the absolute accuracy of results, c) to establish the limits of interference of manganese. aluminum, and titanium, d) to reexamine critically the reduction and recovery of oxygen from oxide powders of various sizes, and e) to evaluate critically the eight steels of the Bureau of Standards."' Apparatus The apparatus used in this investigation is shown in Fig. 1. It has been used for over three years, during which several modifications were made. A brief description of the apparatus is as follows. The transparent silica or Vycor tube, E, is joined to the Pyrex head, B, by mean of a face to face ground joint sealed with mercury. A similarly sealed ball and socket joint would also have been satisfactory. A standard tapered ground joint, successfully used by some investigators, was tried, but in the absence of grease or vacuum cement it was very difficult to disassemble the joint. The graphite crucible, G, 15/16 or l 1/8 in. OD, 2 1/2 or 3 in. high, 1/10 in. wall, shown enlarged in Fig. 3a, is made from the rods containing less than 0.08 pet ash. Two baffles, overlapping sufficiently to prevent spattering, are inserted in two opposite slots cut on a band saw. Two small holes in the baffles permit the temperature measurement of the melt. A second type of crucible, Fig. 2, G, shown enlarged in Fig. 3b, is also satisfactory, though not as convenient as the crucible shown in Fig. 3a. Somewhat similar but more elaborate crucibles with baffles were first tried by Ericson and Benedicks,'" but were abandoned in favor of a crucible with a stopper and a peripheral graphite powder filter. Various versions of their crucible with a stopper have later been used by other analysts, 10-27, 27-30 The crucible is packed directly in E, Figs. 1 and 2, with —35 + 48 graphite powder for shielding and insulation. A minimum layer of 7 mm of powder is necessary for keeping E cool and minimizing the blank. The first use of graphite powder was made by Sloman,10-23 Who found that —200 mesh was the most satisfactory. The author tried various size powders from +20 to —100 mesh and found that a) particles of 28 mesh or larger were not sufficiently insulating and were heated by the induction current, b) the powder finer than 60 mesh packed too much and did not readily permit the escape of gases even when the crucible was heated very slowly; hence, the powder was occasionally blown out of the side in the crucible and in the mercury pump. The optimum size powder is, therefore, 35 to 48 mesh size or 0.4 mm in average diameter. The furnace is designed to eliminate excessive amounts of

Jan 1, 1959