Search Documents

By W. H. Coghill, A. M. Gow, M. Guggenheim, A. B. Campbell

The object of this paper is to discuss the fundamental principles of ball milling and to present some observations which have been made in laboratory and plant investigations. The discussion will be limited to wet grinding of ores in cylindrical mills, but doubtless many of the principles involved will be equally applicable in the other fields of fine grinding in which mills of the same type are used. In the concentrators of the United States there are about 650 ball, rod, or pebble mills, operating or ready to operate, and these have about 100,000 connected horsepower. For grinding in cement plants there is about three times this connected horsepower, and other industries have an unestimated amount, all used for the general type of grinding that is to be discussed here. It is true that these figures do not represent stupendous amounts of power, but when one considers that ball milling is often the ((bottle neck" in a concentrator and that it often accounts for the largest single item in the cost sheet, the importance of a comprehensive understanding of the principles of ball milling can be appreciated. Much of the past literature devoted to the subject has been concerned with the Kick-Rittinger dispute over evaluating grinding, or with dissertations on ball paths and the closely allied impact versus attrition hypotheses, or with the exclusive consideration of certain specific variables, such as mill speed or circulating load, irrespective of the other factors in operation. Such subjects may be dismissed with but little discussion in what may be called, by comparison, a new philosophy in the study of ball milling. Briefly, this '(new philosophy" consists of using power as an index of the mill operation, and investigating grinding from the standpoint of set and induced varisbles, with emphasis on the latter.

Jan 1, 1935

By Alfred Boyles

THE experiments described below are a continuation of work on the graphitization of cast iron conducted as part of the program of funda-mental research at Battelle Memorial Institute. In previous work it was found that melting in hydrogen increased the amount of eutectic and in others i produced al marked changes in the size of the graphite flakes. These effects seemed to be III sulphur and manganese present in the material studied. Iron-carbon- respond silicon alloys did same manner as mg cast iron and there was no evidence to show that hydrogen was able to stabilize the carbide in such alloys unless additions of sulphur were made. The two alloys examined contained about 2 per cent of FIG. 1.-APPARATUS FOR MELTING UNDER PRESSURE. silicon. The present paper is con- A, inlet for gas. cerned with alloys of lower silicon B, outlet for evacuation. content and describes the structural C, power lead. D thermocouple changes produced by melting in E, plug for access to furnace. various atmospheres at pressures F, crucible. ranging from a partial vacuum up to 300 lb. per sq. inch.

Jan 1, 1939

By Walter H. Munk

Generation of Waves by storms, and the transformation of waves in shallow water by local bottom topography are briefly reviewed. A detailed description of water motion in waves explains the nature and distribution of wave forces. A numerical example dealing with forces and moments against vertical piles summarizes the principles involved. Introduction The oil industry is moving into the open waters of the Gulf of Mexico. The design and construction of offshore drilling rigs present a number of difficult problems, among them problems involving the action of waves on fixed and floating structures. This paper deals with our present knowledge of ocean waves as it pertains to these problems, and the principles involved in computing wave forces against fixed structures. It is hoped that the more difficult case pertaining to floating structures can be discussed at a later time. None of the engincering aspects of the problem are entered upon in this paper, yet an understanding of the principles presented here should be helpful in the solution of practical problems. Waves are capable of exerting almost unbelievable forces. During a gale, waves at the harbor entrance of Amsterdam Canal in Holland lifted a 20-ton concrete block, which was resting on the bottom in 12ft of water, and deposited it on top of a pier which was 5 ft above the high water mark. At Wick Breakwater in Scotland, a mass of large stones in cement and bound together with iron rods, weighing 1350 tons, was broken loose and moved bodily! But one need not go to Holland or Scotland to find evidence of damage that waves are capable of inflicting (Fig I and 2). What is the mechanism by which waves are capable of exerting such enormous forces? To answer this, we must consider briefly the nature of wave motion. When a wind blows over a wheat field, waves appear to travel across the field, whereas the wheat itself remains rooted, slowly swinging back and forth. Similarly, in the case of water waves, the waveform travels swiftly over the water surface, whereas the water particles oscillate back and forth, but scarcely advance. The speed of the wave form is called wave velocity, the speed of the water particles is called orbital velocity. This fundamental difference between wave velocity and orbital velocity was already recognized by Leonardo da Vinci. Orbital velocity is generally much slower than wave velocity except for a breaking wave, a case which is of particular importance in the application to engineering problems. Forces exerted by the waves on obstacles

Jan 1, 1949

By Alexandre Mitinsky

The theory of elasticity, the science of the strength of materials, and all our calculations regarding engineering structures are based on Hooke's law, that in loaded bodies the deformations are proportional to the load producing them. Without this law it would be impossible to design intelligently engineering structures such as bridges, frames, axles, etc. This being the case, the proportional limit,l that is, the point at which deformation ceases to be proportional to load, is the most important factor in engineering design. Further, the working fiber stress should be fixed in reference to the proportional limit instead of, as is usual, in reference to the ultimate strength. The incorrect use of the ultimate strength instead of the proportional limit in setting the working fiber stress is probably due to two reasons: (1) it is a more delicate operation to measure the proportional limit; (2) it is usually assumed, though incorrectly, that the proportional limit is determined by the ultimate strength. In Germany the poin't at which permanent set first appears is often taken instead of the proportional limit. The two points will coincide if Gerstner's law, that elastic deformations are proportional to the loads producing them both before and after permanent set, is true; and the limit of proportionality and the elastic limit or point of permanent set will both be represented on a stress-strain diagram, by the point at which the line ceases to be a straight line and becomes curved or changes its inclination. It is to be further noted that the difference in definition between proportional limit and elastic limit introduces a difference in methods of determination in the testing laboratory. The German method of determining the elastic limit by alternately loading and unloading the test specimen is a lengthy process and time has in itself a very considerable influence on the results of physical tests.

Jan 1, 1916

By J. R. Stack, H. H. Alexander

Prior to 1915, numerous attempts were made to treat tin concentrates in the United States, but for various reasons they were unsuccessful. Tin ore is said to have been found in nearly every state, but none of the deposits has proved to be of commercial importance. An annual output of a few hundred tons in Alaska is the only domestic production; hence any considerable production of tin in the United States must be from foreign ores. The most promising occurrence of tin was found in the Black Hills, S. Dak.; in the early development stage, it was called the Cornwall of America. Associated with the tin is tungsten The story is told that an exceedingly fine specimen of the Black Hills ore was sent to England to encourage stock promotion; the desired effect was produced until a skeptic chipped off a small piece, which the analysis showed to be wolframite. First Attempts at Smelting One of the first promising attempts at tin smelting in the United States was made by R. T. White at Bayonne, N. J., in 1903. Mr. White, after spending some time in England studying the methods of tin smelting, organized a company called the International Tin Co., and erected a plant to treat tin concentrates from the Straits of Malacca. About the time the plant was completed, the English Government placed an export duty of 40 per cent. ad valorem on tin concentrates exported to other than British smelters, which duty made it impossible to operate this plant so the enterprise was abandoned, As this export duty is still effective, the only source of tin-ore supply for the United States is the Bolivian concentrates. Bolivian Tin Concentrates Unlike the alluvial placer deposits, nearly all Bolivian tin occurs in lode deposits and some of the highest grade ores contain only a small

Jan 1, 1924

By J. G. Eenink, R. A. Cunningham

One phase has been completed of a laboratory invesrigation of formations with relatively high permeability under conditions of overburden, formation and mud coltrmn pressures. The following statements are based on these tests within the limitations described. Drilling rate decreased when mud column pressure was greater than formation pressure. The decrease was primarily due to a layer of cuttings and mud particles held to the hole bottom by the difference in pressure. Much of the force of the bit was wasted in this layer and was unavailable for penetrating virgin formation. Adequate jet velocities helped clean the filter cake and chips away and resulted in increased drilling rate — the higher the jet velocity the faster the drilling rate. Drilling rate increased slightly when formation pres sure was greater than mud column pressure. The i11(reuse resulted from cleaning the hole bottom as formarion fluid flowed into the borehole. Overburden pressure had practically no effect on drilling rate. INTRODUCTION Some formations are difficult to drill in a wellbore hole but are easily drilled under atmospheric conditions in the laboratory. The reasons for this apparent difference in drillability are not fully understood. An increase in formation compressive strength causes a reduction in drilling rate. It has been shown by Griggs1, Handin2 and others3-1 that formation strength increases under conditions of high hydrostatic stress. Based on these results, a decrease in drilling rate would be expected with increased drilling fluid pressure in formations of low permeability having low formation fluid pressure. Such a decrease has been shown by Murray. et a1 and Eckel" This effect holds even when using nitrogcn under high pressure as the drilling fluid (unrc-ported tests from the Hughes laboratory). Poor bottom-hole cleaning may account for decreased drilling rates. Even though it may not be easily explained, evidence of poor cleaning can easily bc seen. One evidence is the increased drilling rate that accompanies decreased balling obtained with addition of oil in some muds used to drill shales.4,7,3 Many variables can affect drilling rates. These may include mud composition and properties, formation properties, bit types and operating conditions, formation fluid, mud column and overburden pressures. These must be studied a few at a time under carefully controlled conditions which simulate actual conditions as closely as possible. The purpose of this work was to investigate effect of overburden, formation and mud column pressures on drilling rates in permeable formations. These tests were suggested by conditions shown in Fig. I. Represented is a borehole drilled into a formation with relatively high permeability. In the vicinity of the hole bottom there exists a mud column pressure, P a formation fluid pressure, P and an overburden pressure, The mud has low water-loss properties and sufficient weight to more than overbalance the formation pressure. Laboratory investigation included a range with formation pressure greater than mud column pressure. NOMENCLATURE Pm mud column pressure = pressure of drilling fluid or mud at hole bottom Pf, formation pressure = pressure of fluid in intersticies of formation

By J. C. Griffiths, D. W. Bennion

A mathematical model, which does not assume a priori that stratification exists, but was designed to test for the stratification was developed. The model segmented the reservoir horizontally into areas of common variance, then divided it vertically into strata (if strata were present). Next, trend surface techniques were used to determine the lateral extent and variation of each stratum. The model was tested on two reservoirs (sandstone and limestone) using porosity as the reservoir rock property. The sandstone reservoir contained approximately 60,000 samples from 2,000 cored wells, while the limestone reservoir had approximately 24,000 samples from 430 cored wells. Within the areas of common variance tested, the model was able to distinguish four separate lithological units or zones in the sandstone reservoir, four in the Marly section and seven in the Vuggy section of the limestone reservoir. INTRODUCTION To accurately predict the movement and production of fluids from a reservoir rock, it is necessary that the reservoir engineer have a knowledge of the rock properties and their distribution throughout the reservoir. For this study, a reservoir rock is defined as a solid containing interconnecting holes or voids which occur relatively frequently and are dispersed within the rock in a regular or random manner. The fraction of bulk volume that these interconnecting voids occupy is called porosity. The rock must also possess sufficient permeability to allow fluids to move through it and it may be composed of one or more strata or lithological units. A stratum or lithological unit as defined in this study is a body or volume of reservoir rock whose properties are so distributed that its lateral and vertical extent can be traced throughout or through a portion of the reservoir. Operationally, the existence of strata are question- able unless the variance within strata is less than among strata. Within the past few years computers have been widely used as a tool for calculating movement and production of fluids from reservoirs. Most prediction models require some type of a mathematical description of certain reservoir rock properties. In the past, most of these models have been relatively simple. Some have assumed vertical variation but no lateral variation, while others have assumed lateral variation but no vertical variation. In general, most of these models have not used functional relationships to predict reservoir rock properties as functions of position. The object of this study was to develop a model which would predict lateral and vertical variations of reservoir rock properties. Since samples are usually available from only a small portion of the total reservoir rock, it seemed logical that if measurements from these samples were to be used to infer the properties of the actual reservoir, the data should be treated statistically as a sample from the total population (reservoir). Therefore, the model developed in this study to predict reservoir rock properties was a stochastic model. The model was tested using porosity (a macroscopic reservoir rock property) measurements from two reservoirs — the first, a sandstone reservoir from which 60,000 samples were obtained; and the second, a limestone reservoir with 24,000 samples. Several investigators have proposed methods to determine the vertical and areal variation of a reservoir rock property. Stiles: Dykstra and Parsons 2 and Suder and Calhoun3 have all developed waterflooding prediction techniques which assume vertical variation but no lateral variation. Stiles developed a method to segment a reservoir arbitrarily using frequency distribution. Law4 suggested that porosity has a normal frequency distribution and that permeability has a log-normal frequency distribution. Elkins and Skov 5 proposed that when a reservoir is segmented vertically, the

Jan 1, 1967

By Robert Maes, Robert de Strycker

The Fe-Ni-As phase diagram has been established by the study of about a hundred alloys, by microscopic observation, and by thermal analysis, with arsenic contents up to 50 pct. The iron and nickel arsenides present extensive solid-solution fields, owing to the substitution of nickel by iron and vice versa; the extent of the solubility field of each compound has been determined with an accuracy of ±1 pct. In the investigated range of compositions, the solidification reactions were established, and the temperatures of the invariant reaclions detevmined with a preciston of iZ°C in the most favorable and ±5°C in the least favorable cases. The isothermal lines of the liquidus surface have also been drazum, with an accuracy estimated at i5°C. Reactions in the solid state, which take place for the formation or the decomposition of certain phases , were investigated in detail. ThE constitution diagram of the Fe-Ni-As system is fundamental for the understanding of the properties of nickel speiss; these by-products of the extraction of certain nonferrous metals indeed often contain the three elements iron, nickel, and arsenic as main constituents. The Fe-Ni-As system has already been the object of earlier investigations. In 1932, Guertler and Savels-berg' have presented some elements of the ternary phase diagram, for arsenic contents up to 55 pct (all percentages in this paper are given in weight percent), including the vertical section FezAs-Ni&s2. This investigation is, however, incomplete and certain anomalies suggested the necessity to verify the results published by these authors: the section Fe2As-Ni5AsZ, for example, is presented as quasi-binary, with a field of complete miscibility in the solid state, even though these compounds do not have the same structure. Recently, ~useck' established an isothermal section at 800°C in the Fe-Ni-As system by X-ray diffraction and microscopic examination of water-quenched alloys. These techniques are sometimes inaccurate for the determination of the fields where alloys are liquid at the investigated temperature, and they may lead to erroneous conclusions when a compound exists at the investigated temperature but is not stable at room temperature and cannot be maintained by quenching. LIMITING BINARY PHASE DIAGRAMS The Fe-As constitution diagram has been the object of several investigations which have been reviewed by Hansen and Anderko.3 For the Ni-As phase diagram, a recent study has been effected by Yund.4 In this system, Heyding and calvert5 have determined the existence of a compound of unidentified structure at arsenic contents slightly higher than those corresponding to Ni5As2 and at temperatures lower than about 200°C; by analogy with iron and cobalt arsenides, this compound could correspond to the formula Ni2As, as suggested by Kulle-rud; although this is not definitely established. In the region of arsenic contents from 35 to 55 pct, Fried-rich7 detected anomalies in the solidification reactions; an interpretation of these anomalies was given by Hansen ,8 which assumed that the solidification reactions in practice are not in equilibrium, but are meta-stable. The main features of the Fe-Ni constitution diagram are the existence of a complete miscibility field, at least at high temperatures, for the fcc phase (which will be designated by My in the remainder of this work) and of a limited solubility field for the bcc phase (designated by Ma). EXPERIMENTAL METHODS The fundamental technique used in this investigation was microscopic observation, which allowed the determination of the reactions occurring during solidification of the alloys, and possible reactions in the solid state.

Jan 1, 1968

By E. W. Engle

Fox several years the Fansteel Products Co. has been engaged in the production and development of various of the rarer metals. It is at present engaged in the commercial production of tantalum, tungsten, and molybdenum in a very high state of purity. The information contained in this paper is partly a general compilation from various sources and partly information obtained as a result of recent years of work in the laboratory of this company. Tantalum, tungsten, and molybdenum form a group peculiar to themselves among the commercially available metals. Their very high melting points (tantalum 2770° C., tungsten 3350° C., and molybdenum 2550° C.) set them apart so far as the metallurgical processes for their production are concerned. Further, when properly prepared and treated they will stand a somewhat unusual degree of cold work, that is work below the temperature at which marked crystal growth takes place. Such cold-worked metal may show a high tensile strength; tantalum to 130,000 lb. per sq. in., tungsten to 490,000 lb., and molybdenum to 260,000 lb., in the form of fine wire. In physical appearance, these metals are not unlike some steels; they may be better described by saying that polished tantalum some¬what resembles lead; polished tungsten, iron; and polished molybdenum, nickel. The polished surfaces of all three remain untarnished in ordinary air. Air containing corrosion-producing impurities will, in general, show molybdenum the least resistant to corrosion and tantalum the most resistant. Molybdenum has, however, a high degree of resistance to corrosion by hydrochloric acid, a property that should render it of commercial interest. On the other hand, it is markedly attacked by some of the weaker organic acids.

Jan 3, 1925

By Donald W. Petrasek

The effects of selected alloying elements on the elevated-temperature tensile properties of copper alloy -tungsten fiber reinforced composites were invcstigated. A cornparison of the elevated-temperature tensile properties of copper alloy - tungsten fiber reinforced composites, representing soluble systems. was made with copper - tungsten fiber reinforced composites, representing a mutually insoluble system. A linear relation between tensile strength and volume percent fiber content existed at elevated temperatures for all the systenzs investigated. The copper alloy composites were weaker in tension at high volume percent fiber contents than copper composites in which alloying with the fiber did not occur. The tensile strength of the alloyed tungsten fiber decreased with increasing penetration of the alloying element into Ihe tungsten fiber. THE technique of combining strong fibers with relatively weak matrix materials so that the fibers are load-carrying members has been utilized for many years in the reinforcement of plastics with glass fibers. This type of strengthening is currently being extended to include the reinforcement of metals with metallic fibers. Investigations of the room-temperature tensile properties of metal-fiber-reinforced metallic composites have been numerous,'-" but the study of tensile properties at elevated temperatures has been limited. In previous work done at the Lewis Research Center' composites consisting of mutually insoluble constituents were investigated. Composites were made of copper reinforced with uniaxially oriented tungsten fibers. The stress-strain behavior and tensile properties of the composites were related to the tensile properties of the base materials. The tensile strength of the composite was directly proportional to the volume percent of tungsten fiber present, and the full strength of the fiber was realized. Few metal fiber - metal matrix systems exist that are mutually insoluble, and those that do exist are not generally practical. An extension of this work was an

Jan 1, 1967

By AIME AIME

The following changes of address of members have been received at the Secretary's office during the period of Jan. 1 to Mar. 15, 1907. This list therefore supplements the annual list of members corrected to Jan. 1, 1907, and brings it up to the date of Mar. 15, 1907. The names of members who have accepted election during January and February, 1907 (new members), are printed in italics. The large number of changes of address since Jan. 1, 1907, shows the importance of publishing these changes as frequently as possible, and the Bi-Monthly Bulletin has been selected as the means to present this information to the members of the Institute. By a simple method of cutting out these names and addresses and pasting them directly over the corresponding names in the annual list of members, the record can be kept practically up to date, and the value of the list correspondingly increased. For this purpose the changes of address have been printed only on one side of the page. The names of new members, being in italics, are readily distinguished from the others, and can be pasted in approximate alphabetical order on the margins of the pages.

Mar 1, 1907

By Paul M. Tyler

Mineral raw materials, because they are essential to our industrial prosperity and military strength, must be made available in substantial quantities regardless of cost. Variations in the cost of procuring minerals, as compared with the cost of obtaining other commodities, and changes in the cost of production of different minerals relative to one another, will naturally influence the quantities of a given mineral item that can be marketed readily. However, in the last analysis, the cost of winning minerals from the ground usually constitutes only a small fraction of the value of the end-use products and services derived from them. The miner's share of the cost of a typewriter, telephone circuit, or even a modem office building, is almost insignificant. Far more important to the ultimate consumer, therefore, than any minor saving in cost is the assurance of ample supplies of the minerals needed to aliment our expanding economy. To create a successful metal mining operation involves (1 ) the discovery and systematic development of a mineral deposit, (2) extraction of the ore, (3) the mechanical and metallurgical processing to eliminate worthless or harmful impurities, and (4) the profitable disposal of the product. The fist step of the technological process belongs chiefly in the realm of the geologist, the second is a mining engineer's job, the third is mainly up to the millmen and extractive metallurgists; whereas the fourth and equally important step poses a commercial problem that has aspects in common with the marketing of other products. Ore finding is far from being an exact science. There is no mathematical criterion for evaluating the efficiency of prospecting and exploration. Lady Luck shares the honors or assumes part of the blame along with the prospector and geologist. Marketing like- wise involves factors that seemingly defy engineering analysis. Although the other steps can be measured with some degree of mathematical accuracy, even they tend to vary so widely in basic principle, as well as in

Jan 1, 1964

By S. D. Strauss

The marketing of nonferrous metals and of the ores and concentrates from which these metals are recovered is a fascinating trade, international in character, sensitive to every change in the economic tide, and complex in its organization. Each individual metal has its own marketing mechanism; no two are exactly alike. The differences sometimes are a matter of tradition rather than of necessity, but usually they have developed because of the very nature of the problems of producing or consuming the individual metal. This description, because of limitations of space, can do no more than indicate the major aspects of the trade and touch lightly on the marketing structure of each metal. The dictionary states that a market is a "meeting of people for selling and buying." In the case of nonferrous metals this meeting may occur on a half-dozen different occasions between the time the ore has been first mined and the time the refined metal is available for use by industry; or it may not occur at all until after the metal itself has been rolled, drawn, stamped, cast, or forged into a useful semifabricated shape. To illustrate: A Chilean miner may sell his small ore production to a custom mill, which produces concentrates that are sold to an ore dealer, who finances the shipments of the concentrates to a United States custom smelter, which buys these' concentrates for conversion into blister, which is subsequently refined into electrolytic copper and sold. Conversely, much of the production of aluminum is in the hands of integrated concerns that mine bauxite, convert bauxite to alumina, smelt the alumina to produce aluminum, and then fabricate the aluminum into semifinished or even finished products before title to the material changes hands for the first time. Some nonferrous ores are not converted into metal at all but are sold by the miners or dealers directly b the ultimate consumers. A good example would be chrome ores used by the chemical industry. And of course a substantial part of the commerce in nonferrous metals is in scrap, which is the reconversion into useful form of metals that have long since been mined and smelted. Thus, one-third of all the lead used in the United

Jan 1, 1959

By B. G. Agnew

In evaluating fracture treatments, the need to answer such questions as "What zone or zones were actually treated?" and "What was the vertical extent of the treatment" is necessary, since determining effectiveness of the fracture treatwrent depends on knowledge of the reservoir portions stimulated and the vertical extent of the fracture system or systems. Injection of hot or cold fluids during fracturing operations will transfer heat to the surrounding formations and fracture faces mainly by heat conduction. Once injection ceases, temperature anomalies will develop opposite the zone fractured because the rate of temperature decay is less than that opposite zones heated or cooled by flow inside the wellbore or along the cement sheath. Thus, temperature surveys can he used to determine where fractures were generated outside the wellbore and to reasonahly estimate the vertical extent of the fractrires. This technique has been used successfully to evaluate over 344 fracture treatments at depths ranging from 1,500 to 15,700 ft. Examples of actual temperature surveys are presented to show how this method of fracture treatment evaluation can be used effectively and beneficially. INTRODUCTION Stimulation of producing or injection wells by fracturing is commonplace in the industry today. In evaluating these treatments, two basic questions which arise are "What zone or zones were actually stimulated?" and "What was the vertical extent of the treatment?". Knowledge of the reservoir portions stimulated and vertical extent of the fracture system or systems is vital to effect efficient and economical well completions and to assure maximum recovery from reservoirs. Not all fracture treatments are successful and many times the desired or anticipated results are not achieved. When this occurs, it is in most cases the engineer's job to determine why. The answer to this problem forms the primary basis for deciding whether to spend more money for development drilling and/or completion attempts or to forego additional expenditures to improve the particular zone. Also, knowledge of the reservoir portion actually stimulated is invaluable in planning future workovers. This is especially true in wells producing from reservoirs containing multiple porosity stringers or zones. For various reasons, all zones within a reservoir may not be perforated on initial completion with the thought of developing remaining zones through future workover operations. Because particular zones are perforated and fracturing fluid pumped down the wellbore, it cannot be assumed that all perforated zones are stimulated, and in turn drained. Occasionally, unperforated zones which are planned for future development are actually stimulated on initial completion. eliminating the need for future recompletion attempts or all zones perforated initially are not stimulated, thus requiring additional completion work to insure that these zones are adequately drained. In most cases, it is costly. if not impossible, to determine with assurance why a fracture treatment is unsuccessful after the job has been completed and the results tested. Further, unpredictable upper and lower fracture barriers. as well as possible borehole communications (cement channels), do not permit it to be taken for granted that the formation opposite the perforations is the only zone receiving the fracture treatment. Thus. evaluation of fracture treatments is necessary for efficient and prudent well completion practices and should be done simultaneously with the fracture job. Several methods have been used to locate fractured zones, all of which are based on detection of radioactive tracer materials added to either the fracturing fluid or the propping agent. These methods have been helpful in increasing knowledge of fracturing operations; however, they are seriously limited because of cost and inability to detect accurately radioactive tracer material more than a few inches away from the borehole. To develop a better diagnostic tool to pinpoint which zone or zones had actually been fractured, temperature surveys were run after fracturing with heated and cooled fluids. Significant temperature anomalies were found to exist opposite zones suspected of receiving the fracture treatment. From the analysis and examples to be shown, it can be seen that temperature surveys run in a stabilized wellbore several hours after a fracture treatment using hot or cold fluid will yield temperature anomalies which show the actual reservoir portion stimulated, the vertical extent of the fracture system or systems and a qualitative indication of the portion of fracture-fluid volume entering a given depth interval. The experience and illustrations used in this paper are based on evaluation of over 344 fracture treatments during the past three years using this diagnostic tool at depths ranging from 1.500 to 15,700 ft and fracture volumes ranging from 2.000 to 110.000 gal. Based on analyses of these temperature surveys, analyses of fracture gradients and evaluation of several open-hole packer impressions in the West Texas area,' vertical fracturing is the predominant mechanism and horizontal fractures occurred frequently, if at all.

Jan 1, 1967

By B. A. Cheadle, K. P. Steward

Axial tensile, ring tensile, closed end burst, and free end burst tests were done at room tempe.vature and 300°C on three batches of Zircaloy-2 sheathing zuith different textures. Knoop hardness tests were also done on all batches. The mechanical properties of the tubes were largely dependent on the percentages of cold work, but were also markedly affected by the textures, particularly with respect to deformation behavio'r. The deformation behavior observed confirmed Picklesimer's predictions, zuhereas Knoop hardness results could be correlated with texture and yield strength anisotropy after the ,method of Wheeler and Ireland. From the mechanical properties, and from efjectiue strain values deterrlzined at the fractures using a photoqid technique, it zuas concluded that tubing witlz a single preferred orientation of radial basal poles best combines strength and ductility for any given deqee of cold work. THE mechanical properties required in collapsible Zircaloy-2 fuel sheathing for water-cooled power reactors are strength to resist wrinkling deformation by coolant pressure and ductility to accommodate a small amount of deformation in service without rupturing. Zircaloy-2 tubing during fabrication develops pre- ferred orientations of the a Zr grains due to aniso-tropic deformation behavior, and these textures markedly affect mechanical properties. Picklesimer' had predicted the deformation behavior of tubes with various textures, but the texture required to provide the optimum strength and ductility for a given degree of cold work has not been reported. To investigate this problem, tests at three transverse to axial stress ratios were done at room temperature and 300°C on three batches of Zircaloy-2 tubing covering a wide range of textures and percentages of residual cold work. Knoop hardness values were also measured to correlate with preferred orientation and yield strength anisotropy after the method of Wheeler and relland.' 1) MATERIAL For this investigation, three batches of tube-reduced tubing were chosen from the Zircaloy-2 sheathing produced for the Douglas Point Reactor. Individual tubes were 191/2 in. long, 0.600 in. OD, and 0.0165 in. nominal wall thickness. The identities of the batches, together with their textures, are shown in Table I. The tubes had the normal Zircaloy-2 composition3 of 1.5 wt pct Sn, 0.3 wt pct Fe, Ni, Cr combined with the following oxygen concentrations: Batch VII 1140 to 1390 ppm 0 Batch VIII 1400 to 1750 ppm 0 Batch IX 880 to 1320 ppm 0

Jan 1, 1968

By C. E. Sims, H. M. Banta, S. L. Hoyt

OVER the past few years, metallic arc welding has been extended to steels of the hardenable type. As compared with other methods of fabrication, production has been facilitated, service performance frequently has been improved, and the overall results have been so favorable that engineers and production men have placed great emphasis on this application of welding. The metallurgist and welding engineer, however, have been confronted with new problems, since, for one reason, the harder steels are more apt to crack and special precautions must be taken if sound joints are to be procured. Some of the factors that are pertinent to this problem are metallurgical, and it is an object of this contribution to discuss steel manufacture and processing methods and to show how their control assists in reducing the hazard of cracking. By this time, the problem of cracking specifically underbead cracking, or "hard cracks," or parent-metal cracks-is well known, and a large amount of work has been published, both here and abroad, dealing with this subject.1 The tests described are made under restraint to facilitate cracking and, are so designed that a semiquantitative, or at least a relative, value of the cracking tendency is obtained. As one would expect, it has been reported that the incidence of cracking increases with the carbon and alloy content of the steel. More specifically, the cracking tendency is said to increase with the hardenability of the steel, though it is now recognized that the situation is not so simple. The phenomenon itself, on the other hand, has been but loosely described, and it is in only broad generalizations that this cracking has been related to steel metallurgy. Thus, while it has been abundantly demonstrated that the hardenable aircraft steel, S.A.E. 4130, must tend to crack when arc-welded, the problem still remains of why two lots of the same composition and the same hardenability can vary so greatly in cracking tendency, or what it is about the prior metallurgical history that so strongly affects the results. Further, while the efficacy of preheating and postheating in preventing cracking is recognized and utilized in production, the mechanism by which they function seems not to have been described. These points are thought to be significant in the production of steel for fabrication by metallic arc welding and, hence, of interest to mill and process metallurgists and welding engineers. Consequently, it is another object of this paper to discuss the mechanism of parent-metal cracking, including the influence of the condition of the steel and the control of cracking by manipulation of the time-temperature conditions during and after welding. A new method of rating the cracking. tendency is also discussed, and the results of the test are related to steel composition and structure or prior history. The work to be described was the outgrowth of work in 1940-41 at Battelle Memorial Institute 0n two projects, one

Jan 1, 1945

By A. M. Abouzeid, S. Chander, D. W. Fuerstenau

Today numerous ores contain valuable minerals in finely disseminated form; and although the recovery of these fine mineral particles is generally exceedingly difficult, diminishing raw material resources necessitates the recovery of such mineral values. In many systems, the efficiency of recovering fine particles is still extremely low and often fine particles must be discarded as slimes. However, in recent years, various advances have taken place in the recovery of mineral particles in the very fine size range. In this paper, the background and performance of a number of processes for fine particle processing and separation are reviewed and discussed, particularly from the point of view of how fine particle recovery might be improved.

Jan 1, 1979

By Charles S. Barrett, Robert F. Mehl, Dana W. Smith

The Widmanstatten figures found in the steels have been long recognized and in some aspects carefully studied,' especially as they occur in cast hypoeutectoid alloys. Aside from the practical importance of the structures obtained in the steels by various heat treatments, a study of the characteristics of these figures is interesting because of the rich opportunity the system affords to obtain new data on the mechanism of segregation from solid solutions. This opportunity is twofold: first, by changing composition within the austenite range the proeutectoid precipitate may be changed from that of ferrite to that of cementite, thus offering the same opportunity for changing the type of precipitate while maintaining the same basic lattice as that afforded by the Cu-Zn alloys;2 and second, the eutectoid inversion leads upon drastic quenching to the formation of martensite, a Widman-statten figure of unique interest from the crystallographic viewpoint, particularly in comparison with those formed on slow cooling.3 We have, therefore, two types of structure to study: that formed on slow cooling of hypoeutectoid and hypereutectoid alloys, and that formed on quenching hypoeutectoid, eutectoid, and hypereutectoid alloys. For each of these types of structure we require the crystallographic plane in the mother austenite along which the precipitate forms (we shall see that the precipitates in these alloys are invariably platelike in form), and also the orientation of the precipitate upon this plane. Some of these

Jan 1, 1933

By R. A. Flinn, R. D. Pehlke, D. R. Glass, P. O. Hays

Knowledge of the depth of penetralion of an oxygen jet into the bath of the oxygen converter and of the correlation of penetration with driuing pressuve, lance heighl, and nozzle throat area is vital to the understanding of converter operation. If the penetration is too shallow, then severe and hazardous slopping takes place. On the other hand, if the jel penetrates entirely Lhvough lhe bath for an apprcciublc period of time, bottom damage occurs. In addilion to measurement of the penetralion of the jel, knou~ledge of the circulatory movement in the bath is also of interest in order to evaluale various theories oj-concerter operating behavior which have been published. In this investigation, experimental converters were buill of IOU- , 300-, and 4000-lb capacity. Four independent methods were used to determine penelralion: the onset of bottom marking, a nitrogen bubbler probe, observation througlt an optical syslew built into the oxygen lance, and direcl viewing of the jet issuing from the bottom of the vessel. Good correlation zuas obtained, and empirical relalions for pvedicling perletration were found. These relations were conjzrmed by bottom marking tests in 55- and 110-ton vessels. Within the operaling conditions employed in these tests, the depth to which a single oxygen jet penetrated zuas found lo vary according to the relatiorl ThE technical literature is replete with data concerning the successful use of the basic oxygen furnace or converter in steelmaking. Experimental data are lacking, however, on the vital factors of the depth of penetration of the jet into the bath and the induced circulation. Commercial operating conditions usually have been the result of cut and try experiments in lance manipulation until satisfactory results were obtained. There have been, however, two hotly argued opposing theories concerning desirable depth of penetration and these are exemplified by the Schwarz and Miles patents1,2 on one hand and the Suess patent3 on the other. The Schwarz patent teaches that the jet, issuing from the nozzle at supersonic speed, penetrates deeply "so that the reactions between the iron and the oxygen and between the oxygen and the rest of the smelting components take place in the center of the bath". Specific operating suggestions are given by Miles.2 By contrast, the Suess patent calls for surface Circulalion was investigated by lour methods: by direct observation in 200-lb open baths, by the use of graphite rudders in the 300- and 4000-lb converlers, by direct observalion through an oplical system in the lance, and by various models al room temperature. All were in excellent agreement and indicated that the motion of the bath ulas up at the center, radially outluavd at the surface, and down at the sides. Experi-ments in small and in commercial vessels indicate that it is essential to operate with a jet penetration of approximately 50 pct of the bath depth. Surface blowing results in low oxygen eficienty and in hazardous conditions which may render the process inopeuable. RejYactory dartzage al the bottom of the vessel is only encountered when the jet penetrates to the bottom, and this can be avoided by properly applying the penetration formula. The application of this en/pirical formula in commercial peraations is best when limited to combinations of lance size, pressure, and height which are typically encounteved in the use of a single-hole lance. blowing so that "...the oxygen jet does not penetrate deeply into the molten metal bath and is confined to an impingement area at the central portion of the bath surface". These references are given merely to illustrate the basic differences between the two schools of thought and to point out the need for measurement of penetration for the sake of the operator. For example, it is shown later that inefficient and even dangerous conditions can arise if improper blowing conditions are used. Differences are also evident between the two schools of thought as to the mixing, circulation, and agitation which is to be accomplished by the jet. The Schwarz patent states that "surface contact is not sufficient in most cases to bring about quick reaction, the same as the blowing of the gas over the bath surface or the mere blowing of the gas onto the bath surface". The patent goes on to call for active mixing. In contrast the claims of the Suess patent call for "discharging a stream of oxygen ... to an extent to avoid material agitation of the bath by the oxygen stream". In this patent the circulation is said to be downward in the center and up at the sides of the vessel. A number of investigators4-12 have explored penetration and circulation in transparent models. In general, it is agreed in these tests that the circulation is upward at the center (along the sides of the jet cavity),

Jan 1, 1968

By O. D. Sherby, J. L. Lytton, C. R. Barrett

Randomly oriented polycryslalline copper of 99.995 pcl was tested in tension at temperatures of 626o, 496o, and 406o. The gvain-size mnge investigated was from 0.03 to 0.7 mm. Grain sizes were produced by two techniques: 1) varying the amount of prior cold work and the amealing time at constant annealing temperature so as to obtain various vecrystallized grain sizes with minimum grain growth, and 4 holding the prior cold work constant while varying the annealing time or temperature so as to obtain varying grain sizes by grain growth. Polycrystalline samples (grain size of 0.03 mm) with a strong. [001](100) texture were also studied. The relationship between the steady-state creep rate, Es, and pain size was found to be the same indepentent of the technique used to prepare the various grain sizes. For specimens with grain diameters above about 0.1 mm ea zuas esse)ztiallj~ independent of grain size, while for smaller grain diameters Cs increased slightly with decreasing grain size. Strongly textured polycrystalline copper, which contained low-angle grain boundaries, exhibited steady-state creep rates that were slightly lower than those observed in randomly oriented copper, of the same gain size. The results are explained by conside?%ng- the contribution of grain boundary shearing to the total strain and the effect of grain size on the resulting creep substructure. EXPERIMENTAL observations concerning the influence of grain size on steady-state creep rates are varied and oftentimes conflicting. Numerous early investigators found that an increase in the grain size resulted in a decrease in the high-temperature steady-state creep rate, i,.'-" Other workers have foundthat ef decreases with increasing grain size up to some optimum grain size and then increases with a further increase in grain size.'- '' It has been suggested that es, decreases with an increase in grain size only because the range of grain sizes studied normally lies to the left of the grain size for optimum creep resistance. However, sherbyl2 and Feltham and his co-worker13, 14 have found that even for small grain sizes 2, does not always decrease with an increase in grain diameter but may be proportional to the square of the grain diameter. A possible explanation for the different creep rate-grain size relationships which have been observed is that in most experimental studies different grain sizes have been prepared by annealing at various temperatures. For metals in which the impurity concentration is high (greater than about 0.1 at. pct) this type of

Jan 1, 1968