Search Documents

By W. Allen

FOR the past six years gravity surveys have been used for underground prospecting in the copper mines at Bisbee, Ariz. The primary purpose of the surveys has been to reduce the diamond drilling and crosscutting necessary for exploration. Since many of the orebodies are small, and geologic control is not always apparent, any information that will direct the drilling and crosscutting is highly desirable. Because of extensive development and exploration work in the copper mines at Bisbee, it has been possible to cover more than 630,000 ft of crosscuts on 30 levels with the gravity surveys. In the process the gravity procedures have been refined to a high degree. Density Contrast: For a gravity survey to be successful, a sufficient density contrast must exist between the geologic feature sought and surrounding host rocks. Most mineralized areas will provide this contrast if fairly massive bodies are present. In the Bisbee area the entire sequence of formations, except for alluvium, appears to have specific gravities ranging from 2.65 to 2.70. These values have been determined by means of a large number of cut samples and diamond drill cores. As a further check, vertical gravity differences have been used where nonmineralized sections are known to occur.' The only known major gravity disturbances result from mineralization that has increased the density and the voids that have decreased density. The voids are caused by mining operations and by underground water movement that has developed several areas of caverns. Equipment: While not absolutely essential, a small rugged gravity meter, such as the Worden meter, is highly desirable. A tall tripod, about the height of a transit tripod, permits instrument set-ups in deep water and in locations where fallen timber and muck piles make it impossible to use a short tripod. An additional advantage of a tall tripod is that it places the meter in the center of the crosscut, reducing the error caused by the crosscut void. Size and weight are important, since the only satisfactory means of operating the meter underground is to carry it by hand. A backpack can be used in rare instances but is usually a hindrance because of the close station spacing. The operator's ability to move through tight clearances will improve survey coverage, as it is then possible to move through raises and caved areas and to pass mine cars and machinery with a minimum of trouble. Station Control: Gravity stations are normally located every 100 ft along the crosscuts, at each intersection, and in the face of all stub crosscuts. In areas of high gravity relief, or where small anomalies might be expected, stations may be located at 25 or 50-ft intervals. When possible, the stations should be offset to avoid effects of raises or other voids. The gravity stations on a level are tied to one or more base stations, which are usually located at the shaft or near the portal of an adit. The base stations may be part of a gravity control net that extends to each level in the mine as well as to the surface. Such a net extending throughout the potential area of the surveys is highly desirable, as it is then possible to compare all gravity stations on a uniform basis. The stations that are part of the base net should be carefully established by multiple readings and, if necessary, by a least squares adjustment of the loops. In some instances where levels do not have a shaft station, or where access may be blocked by caving, it may be necessary to establish secondary bases at the top and bottom of the raises that are between levels. Under fair conditions 70 to 90 gravity stations can be located and run in 6 hr by a two-man crew. The best field procedures depend on conditions. Reduction of Field Data: Most of the time required to produce a final gravity map is consumed in processing the data. Each meter reading must be corrected for a minimum of five factors that affect the gravity value in addition to the density contrast being sought. These factors are 1) instrumental drift, 2) station elevation, 3) topography, 4) latitude, and 5) regional gravity gradient. Mine openings, such as stopes and raises, will affect the value. However, it is seldom practical to make corrections for these voids. Usually a rotation is made on the field note on the station, and any

Jan 1, 1957

By Y. Nakada, U. F. Kocks, B. Chalrners

THE orientation dependence of work hardening has previously been studied over the entire range, i.e., including special orientations of high symmetry, in aluminum1-3 and silver.* The differences between various orientations are substantial, and the trend is the same in all fcc crystals. However, there are quantitative differences in behavior between aluminum and silver at room temperature, particularly in the (100) orientation. While many experiments on gold have been reported,5'9 none included the special orientations. We therefore undertook tension tests on gold crystals of the axial orientations (100),(110), (Ill), (211), and, as a representative of single slip, one whose Schmid factor was 0.5 (hereafter referred to as m = 0.5). Single crystals of dimensions 1/4 by .1/4 by 6 in. were grown from the melt1' at a rate of 4 in. per hr, using gold of 99.99 pct purity obtained from Handy and Harman. A growth rate of 1/8 in. per hr, or a purity of 99.999 pct,ll produced no difference in results. The crystals were annealed at 1000°C in air for 24 hr and furnace-cooled down to room temperature, after which they were electro-polished in a solution of potassium cyanide (40 g), potassium ferrocyanide (10 g), soda (20 g), and enough distilled water to make 1 liter of solution, at a current density of 0.02 amp per sq mm. After 2 or 3 hr, a very smooth surface was obtained by this method. Nine m = 0.5, two (loo), one (110), three (Ill), and one (211; crystals were tested at room temperature in a floor-model Instron machine at a tensile strain rate of 0.5 pct per min. The accuracy of the stress measurement was k10 g per sq mm up to 500 g per sq mm, k2 pct for higher stresses. The strain measurement was accurate to t2 pct. The scatter of stress at a given strain among the crystals of the same orientation was small, *5 pct being the largest. The representative stress-strain curves for various orientations are shown in Fig. 1. Table I summarizes the work-hardening parameters as used by seeger.12 Results of other investigators are also included in this table for comparison. There are no previous data for the corner orientations. Values for m = 0.5 crystals agree fairly well with those of Berner. Tm is defined as the stress at which the stress-strain curve begins to deviate from linearity of Stage 11. However, in practice this is a very difficult value to estimate because each investigator has a different idea of linearity. Therefore, the comparison with the values of other investigators may not be valid. In the present experiment, (100) crystals had the highest 111, followed by (111) crystals. The work-hardening rate in Stage I1 was highest for the (111) crystal followed by the (100) crystals. Our value for 0x1 of m = 0.5 orientation agrees very well with those of other investigators. 1) Single-Slip orientation (m = 0.5). These crystals were oriented so that the primary-slip vector was contained in one side face. The dimension perpendicular to this side should then not change if single slip indeed takes place. Within the accuracy of measurement, this dimension did not change during the deformation. Since the accuracy is k0.2 pct, the amount of secondary slip is less than 0.7 pct of the slip on the primary-slip system at 30 pct tensile strain. This is in conformity with the results obtained by Kocks" for aluminum crystals. The tensile axis moved toward (211) during the deformation. Slip bands, Fig. 2(a), were very fine and closely spaced. Some deformation bands were observed. There were no clear-cut cross-slip traces such as the ones observed on aluminum m = 0.5 crystals. 2) (111) Crystals. The orientation of the tensile axis was stable during the deformation. From this observation, one can deduce that at least three slip systems must have operated, and probably all six because the remaining three all have cross-slip relation to one of the first three.' It was very difficult to observe the slip markings. Consequently, we could not confirm by this method that six systems were operative during the deformation. At high strains (above 50 pct shear strain), this orientation had the highest stress-strain curve. At 80

Jan 1, 1964

By F. Weinberg

The relative concentration of 1" at grain boundaries in controlled orientation bicrystals has been examined by autoradiographic techniques, and by activity measurements of grain boundary surfaces exposed by preferential ,melting. The autoradio-graphs indicate that thallium is concentrated at grain boundaries in as-grown bicrystals, but not in zcell-annealed bicrystals. They also indicate that the solute concentration and the distribution on as-grown bicrystal surfaces are markedly different than that of the bulk material. The boundary surface measurements are in agreement with the autovadiographic evidence. On the basis of these measurements, as-grown bicrystals containing approximately 100 ppm of Tl, solidified at rates between 5 and 30 cm per hr and with tilt boundaries greater than 10 deg, exhibited grain boundary segregation equivalent to roughly 10 atomic planes of pure solute. Higher solute concentrations (equivalent to 140 atomic planes of pure solute) were obtained in bicrystals solidified slowly (0.6 cm per hr); slightly higher values were obtained in specimens containing a large angle nantilt boundary. Annealing for various times over a range of temperatures eliminated grain boundary segregation within the experimental uncertainty of the results (equivalent to 1 atomic Plane of pure thallium at the boundary). The results for the as-grown bicrystals can be qualitatively accounted for by assuming the presence of a groove on the solid-1iq;id interface, at the grain boundary. SOLUTE segregation at grain boundaries may be considered in two parts, namely, nonequilibrium segregation associated with the solidification process, and equilibrium segregation in fully annealed materials.' There is much indirect evidence for nonequilibrium segregation, based on preferential etching at grain boundaries and the mechanical properties of as-cast alloys. In addition, some direct observations have been reported in which radioactive tracers were used as solute additions and segregation detected at the grain boundaries by autoradiographic techniques. However, there is little detailed quantitative data on solute concentrations related to grain boundaries, particularly for different freezing conditions and grain boundary configurations. Equilibrium segregation at grain boundaries has been considered both theoretically and experimentally. cean' has made an estimate of the maximum equilibrium solute concentration that might be expected at a grain boundary, based on the lattice distortions in the boundary region. He arrived at a concentration which was equivalent t a monatomic layer of pure solute. A similar value, based on thermodynamic arguments, was calculated by Cahn and Hilliard for the segregation of phosphorus in iron. Experimentally, much higher values of solute concentration at grain boundaries have been reported recently by both Inman and iler' for phosphorus in iron, and Ainslie et 1.' for sulfur in iron. They observed concentrations equivalent to as much as 20 to 100 atomic layers of pure solute at the grain boundaries. However, in both cases it was shown that the observed segregation was not due solely to equilibrium segregation at the grain boundary. In the former case, precipitation effectss due to trace impurities in the material were believed to account for the large amount of solute present at the grain boundary. In the latter case it was shown that a high density of dislocations in the boundary region could provide a large number of additional sites for solute atoms, other than at the grain boundary. Thomas and chalmera have reported on the equilibrium segregation of po210 in grain boundaries of Pb-5 pct Bi alloys. Using autoradiographic techniques, they observed a concentration of polonium along the boundary trace on the surface of annealed bicrystal specimens grown from the melt. The concentration only appeared after annealing, and varied with boundary angle, increasing as the boundary angle increased. Their conclusions have been questioned by Ward," who pointed out that the segregation they observed along the boundary trace was much too wide to be compatible with the usual concepts of the thickness of a grain boundary of several lattice spacings. Also, Maroun et al.,l1 with specimens similar to those of Thomas and Chalmers, found that segregation could only be detected on the specimen surface, suggesting that Thomas and Chalmers' results were associated with an oxidation effect of polonium, and not equilibrium segregation. Thomas and Chalmers replied12 that they did observed segregation at the grain boundary in the bulk material and suggested further experiments were necessary to resolve the difference. The purpose of the present investigation was to examine both nonequilibrium and equilibrium grain boundary segregation in melt grown bicrystal specimens as a function of boundary angle, growth rate, and solute concentration, and to de-

Jan 1, 1963

By A. P. Svenningsen

IN the early stages of design it was not considered necessary that separate crushing plants be built for the new sulphide concentrator and smelter until sometime in the future. The plan was to use the existing crushing facilities for both oxide and sulphide ore. A few additions were contemplated for the existing plants, such as increased bin capacity, and possibly two new secondary crushing units. The more the problem was studied and discussed with the plant operators, the more it became evident that it was complex. It involved the classification of different kinds of ore from the open pit mine -sulphide, oxide and mixed-and how best to separate them so that each kind of ore was given the proper processing and treatment. It also involved the problem of keeping the different ores from being contaminated in bins, hoppers and chutes. Added to these, transportation became complicated and would involve additional handling and loading of ore from crushing plants to conveyors, to bins, and finally to railroad cars which were to be hauled to the concentrator and dumped into the fine ore bin. General In the early part of 1951 it was decided that the concentrator be constructed with ten grinding units instead of seven as originally authorized. The smelter was to be increased proportionally and naturally also the overall tonnages of ore to be handled by the new sulphide plant. Due to this increase in plant capacity and the larger tonnages involved, the difficulties which would arise by using the existing crushing plants were increased to a point where it became evident that the building of new crushing plants for sulphide ore exclusively was technically, as well as economically, advantageous. Authorization was, therefore, given by the company to construct new crushing plants to handle 30,000 tons of ore per day, and capable of reducing the run-of-open-pit ore to the proper size feed for the 10x14-ft rod mills in the concentrator. The ore, mined in the open pit, sometimes comes in pieces as large as 6 to 7 ft diam. The rod mills may call for ore crushed to 3/4 in. The large .size of ore delivered from the open pit determined that a 60-in. gyratory crusher be used as primary breaker. Such a crusher will have a capacity considerably in excess of 30,000 tons per day. The crusher will be a single discharge unit driven by a 500-hp electric motor through a tear coupling and a floating shaft. This type of drive has proven successful at a number of other crusher installations which our company has operating in the United States, Mexico and South America. The tear coupling will protect both the crusher and motor against damage in case of overload. No new features are incorporated in the design of the crusher itself, except that the, discharge chute is made the full width of the crusher with parallel sides instead of the usual converging sides. This change in detail should eliminate, a feature which has been a bottleneck in some of the operating plants and has caused loss of production due to ore hanging up and blocking the chute. The secondary crushing plants will have three 7-ft standard Symons cone crushers and six 7-ft short head Symons crushers. Between the primary and secondary crushing plants a coarse ore bin will be constructed with a nominal draw-off capacity of 30,000 tons of ore. The standard Symons and the short head Symons will be in separate buildings. All the crushing plants and the coarse ore bin are interconnected with conveyor belts for transporting the ore to the crushers at the tonnage rate desired. The final product of the new crushing plants is produced by the short head crushers. It will be delivered onto a conveyor belt leading to the top of the fines ore bin in the concentrator. A separate conveyor belt running the full length of the fines ore bin and provided with a movable tripper of rugged design will discharge the sulphide ore into the bin. The concentrator bin is planned and designed so that the installation of this additional conveyor will not interfere with the operation of the two railroad tracks on which crushed ore is brought from the existing oxide plant. Thus when completed the bin can be filled simultaneously by ore from the new crushing plant and by ore from the existing leaching plant.

Jan 1, 1952

By E. J. Roberts

Prior to 1916, thickening was an art, and any accurate decision as to what size of machine to install to handle a given tonnage of a specific ore must have been one of those intuitive conclusions, based on both intimate and extensive acquaintance with thick-ners and ore pulps. Then in 1916 "knowledge of acquaintance," became "knowledge about" with the publication of the Coe and Clevenger paper.' The unit operation of thickening had graduated to the status of an engineering science. The fundamental similitude relationships for the two major phases of the operation were defined so clearly that batch tests on models as small as liter cylinders could serve to specify protypes as large as 325 ft in diameter. It is quite apparent from reading the literature that Coe and Clevenger's contribution is not generally appreciated. In so far as the basic engineering relationships are concerned, the only real advance which has occurred in the 30 odd years which have elapsed since the Coe and Clevenger paper is the recognition of the effect of the rakes on the thickening process. Bull and Darby2 noted this in 1926, and the extensive use of the "gluten type" thickener, in which the effect is magni-fied, bears witness to its importance. Comings3 further verified this effect of the rakes. As a matter of fact, a number of papers show an apparent regression from the Coe paper in that the area determinations are made on the basis of a single test from One concentration of solids. Coe and Clevenger amply demonstrated that this is unsafe, since the controlling zone may be one other than that of the feed dilution. Comings3 neatly demonstrated this without apparently realizing it. Of course there have been significant advances in the application of the operation to industry. Open tray thickeners were introduced to save area; balanced tray thickeners, washing thickeners, and multifeed clarifiers were developed with all of their special hydraulic and mechanical problems. Combinations of all kinds have been introduced, such as combination agitators and thickeners, combination flocculators and clarifiers, combination thickeners and filters. With the establishment of the operation on a firm engineering foundation, installation was facilitated and expansion proceeded. There are still problems, of course, functional as well as mechanical. Sometimes the moisture in the underflow obtained in practice is not as low as is expected on the basis of the test data. Sometimes the underflow is so "thick " that its discharge and subsequent handling requires special attention. Island formation plagues some operators. The use of the thickener as a surge basin and blending tank in the cement industry poses unusual problems. Design of rakes and the drive mechanism must be continually im-proved. Corrosion problems must he overcome. Power requirements for raking the settled solids occasionally is the controlling factor as it was in the case of the all American Canal desilting installation. Other similitude relationships and design problems come into the picture when we enter the field of clarification or nonline settlement. We have an energy dissipation problem in introducing the feed and any models must satisfy the Froude model relationships. Autoflocculation requires detention which involves the same similitude laws that we encounter in the compression zone. Approach to an Exact Science The next step beyond having control of the similitude relationships is to understand the why of these relationships right back up the line to first principles. The ultimate might be that, if given the mineralogical composition of the solids and their size distribution together with an analysis of the suspending liquid, we could calculate the entire thickening behavior of the system. Then we could say we had reduced the operation to an exact science. True it might be more trouble getting this basic analytical data than to make our empirical determinations for area and volume, and we would need an ENIAC to calculate the results, but that does not detract from the desirability of such understanding. Considerable work has been done by the chemical engineers with this end in view. Comings,3 Egolf,4 Work,5 Kam-mermeyer,6 Steinour,7 and others have studied the problem. The writer has no final answer to the thickening story but would like to propose a picture of the mechanics of the two phases of thickening which has been found useful in understanding the subject and which leads to some convenient relationship in treating the compression step and arriving at the compression depth.

Jan 1, 1950

ARTICLE I Name and Object Sec. 1. This Division shall be known as the Institute of Metals Division of the American Institute of Mining and Metallurgical Engineers. Sec. 2. The object of the Division shall be to furnish a medium of cooperation between those interested in the field of physical metallurgy; that is, the nature, structure, alloying, fabrication, heat treatment, properties and uses of metals; to represent the AIME insofar as physical metallurgy is concerned, within the rights given in AIME Bylaw, Article XI, Sec. 2, and not inconsistent with the Constitution and Bylaws of the AIME; to hold meetings for the discussion of physical metallurgy; to stimulate the writing, publication, presentation and discussion of papers of high quality on physical metallurgy; to accept or reject papers for presentation before meetings of the Division. ARTICLE II Members Sec. 1. Any member of the AIME of any class and in good standing may become a member of this Division upon registering in writing a desire to do so, but without additional dues. Sec. 2. Any member not in good standing in the AIME shall forfeit his privileges in the Division. ARTICLE III Funds Sec. 1. The expenditure of the funds received by the Division shall be authorized by the Executive Committee of the Division. ARTICLE IV Meetings Sec. 1. The Division shall meet at the same time and place as the annual meeting of the AIME, and at such other times and places as may be determined by the Executive Committee subject to the approval of the Board of Directors of the AIME. Sec. 2. The annual business meeting shall be held within a few days before or after the annual business meeting of the AIME. Sec. 3. At a meeting of the Division, for which notice has been sent to the members of the Division through the regular mail or by publication in the Journal of Metals at least one month in advance, a business meeting may be convened by order of the Executive Committee and any routine business transacted not inconsistent with these Bylaws or with the Constitution or Bylaws of the AIME. Sec. 4. For the transaction of business, the presence of a quorum of not less than 25 members of the Division shall be necessary. ARTICLE V Officers and Government Sec. 1. The officers of the Division shall consist of a Chairman, a Senior Vice-Chairman, a Vice-Chair -man, a Secretary and a Treasurer. The office of Secretary and Treasurer may be combined in one person, if desired by the Executive Committee. Sec. 2. The government of the affairs of the Division shall rest in an Executive Committee, insofar as is consistent with the Bylaws of the Division and the Constitution and Bylaws of the AIME. Sec. 3. The Executive Committee shall consist of the Chairman, Senior Vice-Chairman, Vice-Chairman, past Chairman, Secretary, and nine members, all of whom shall be nominated and elected as provided hereafter in Article VII. Sec. 4. The Chairman, Senior Vice-Chairman and Vice-Chairman shall serve for one year each, or until their successors are elected. Each member of the Executive Committee shall serve three years. The Chairman shall remain a voting member of the Executive Committee for one year after his term as Chairman. Sec. 5. The Treasurer of the Division shall be invited to meet with the Executive Committee, but without ex-officio right to vote. He shall be appointed annually by the Executive Committee, from the membership of the Executive Committee or otherwise. Sec. 6. The annual term of office for officers of the Division shall start at the close of the Annual Meeting of the Institute and shall terminate at the close of the next Annual Meeting. ARTICLE VI Committees Sec. 1. There shall be standing committees as follows: Programs Committee. Finance Committee, Membership Committee, Annual Lecture Committee, Technical Publications Committee, Mathewson Gold Medal Committee, Nominating Committee, Education Committee and such other Committees as the Executive Committee may authorize. Sec. 2. It shall be the duty of the Programs Committee to secure the presentation of papers of appropriate character at meetings of the Division. Sec. 3. It shall be the duty of the Finance Committee to inquire into and examine the financial condition of the Division and to consider proper means of increasing its revenue and limiting its expenses. The Finance Committee shall audit the accounts of the Division and report to the Executive Committee prior to the Annual Meeting of the Division. It shall render a budget to the Executive Committee estimating receipts and expenses for the ensuing year so that action can be taken on same at the first meeting following the Annual Meeting.

Jan 1, 1953

By P. G. Shewmon

A novel technique for determining the surface energy (?) and its derivative with respect to orientation, (?') is described. Essentially it involves the 'floating" of a wedge on the substrate, said wedge being made of a material which is not wet or only slightly wet by the substrate, i. e., as a greased needle "floats" on water. A thermodynamic analysis of a system in which the wedge is supported entirely by surface energy is given. If the original suyface is not at a cusp orientation, the surface tension is directly measurable from the groove angle formed. If the original surface is at a cusp orientation, there may or may not be a groove depending on the relative value of ?' and the weight of the wedge. Experiments primarily on copper and silver showed that sapphire, quartz and refractory metal wedges were wet while graphite wedges were not. The technique was demonstrated to work using graphite wedges, but the results obtained were not as eccurate as those obtained by other workers using the wire-creep experiments. It is concluded that the technique might prove most useful with non-metals where ?' is large and filament creep experiments would be quite difficult. If an absolute value of the surface free energy (?) of a metal is to be determined, the most reliable methods used to date measure an average over the various orientations exposed on a polycrystalline sample. For example, ? for silver, gold, and copper have been measured by determining the force required to just keep a thin wire,' or foil,' specimen from contracting under the influence of ?. Herring 3 has predicted and experiment confirms, that the sensitivity of this method is inversely proportional to the grain size.' Thus it cannot be used to measure ? for a particular orientation by using a foil single crystal or a very coarse-grained specimen. An accurate value if ? for tungsten averaged over a range of orientations has been determined using a field emission technique. The same techniques cannot or have not been used to measure ? for non-metallic solids, and as a result the values available are much less accurate.4 This Paper resents a means of making an absolute determination of ? for a particular surface orientation on any solid, as long as the given surface orientation does not break up into other orientations during an anneal. Experimentally ? is found to vary with orientation and at a few low index orientations it is found to have a cusped minimum, i.e., the derivative of ? with respect to the orientation of the surface changes discontinuously at the low index orientation, see Fig. 1. The slope of a plot of ? vs orientation (herein designated ?') is called the torque on the surface, since it tends to rotate the exposed surface toward the low index orientation, or if the surface is at the cusp orientation it opposes any force tending to rotate the surface out of the low index orientation. The ratio ?'/? has been determined for a few metals, but in cases where this ratio is high there is presently no means of determining either ?'/? or the absolute value of ?' for the orientations present on an annealed surface. The technique discussed herein also provides a means of determining an absolute value of ?' for those orientations which deviate only infinitesimally from a cusp orientation. It should work best on surfaces where ?'/? is large; that is, for cases where no other technique is available for measuring ?'. Aside from trying to learn more about surfaces through measuring ? and ?', the primary reason for wanting values of ? or ?' is to study adsorption. From measurements of the variation of ? for a particular orientation with the concentration of an impurity, one can obtain the number of impurity atoms adsorbed per unit area (Ti) on that orientation using the Gibbs adsorption equation.' where µi is the chemical potential of the adsorbed impurity. Thus, if absolute values of ? could be obtained for the free surface of a given surface orientation as a function of µi, ri could be determined for the given orientation. Furthermore, by equilibrating a grain boundary with the given surface at various values of ki, one could also determine ri for the grain boundary. Similarly Robertson 6 has pointed out that if y is taken to be a continuous function of and µi, then a2 ?/a @a µ2 = a2 ?/a pi a +. Thus, at all orientations away from cusps the following equation holds From a measurement of ?' vs ki, it is thus possible

Jan 1, 1963

By R. W. Balluffi, R. Resnick

NUMEROUS investigations of chemical diffusion in a brass have been made and the results are collected in several places.1-3 This work has been mainly concerned with the determination of the chemical diffusivity as a function of composition and temperature. In 1947 Smigelskas and Kirken-dall&apos; showed that zinc and copper diffuse at different rates in face-centered-cubic brass, and since then, a number of efforts have been made to determine the intrinsic diffusivities of zinc and copper in this alloy.1, 5-9 Horne and Mehl8 in particular have recently determined the intrinsic diffusivities as functions of temperature and composition using sandwich-type couples and inert markers. Inman et al." also have determined the intrinsic diffusivities in homogeneous alloys using tracer techniques. When the present work was started, no information of this type was available. Consequently, measurements of the intrinsic diffusivities were made as a function of temperature at a constant composition of 28 atomic pct Zn with vapor-solid diffusion couples where the zinc was diffused into the diffusion couple from the vapor phase. The application of these couples to the study of diffusion in a: brass has been described previously.0,7 The temperature dependence of the intrinsic diffusivities was found to follow the relation D, = A, exp(-Hi/RT) and the values of Hzn, and Hcu, were found to be closely the same. It is emphasized, however, that the chemical dif-fusivity (D = N1D2 + N2D1) is a composite diffusivity and does not necessarily follow this exponential form. It is usually found to do so within experimental error for substitutional alloys because the heats of activation of the intrinsic diffusivities generally are not greatly different.&apos;" Also, at the onset of this work, there was no information available concerning possible unequal diffusion rates of individual components and the existence of a Kirkendall effect in alloys with other than face-centered-cubic structures. Since then, two reports indicating a Kirkendall effect in body-centered-cubic ß brass have appeared. Landergren and Mehl" have published a note describing Kirkendall diffusion experiments with sandwich-type couples. Inman et a1.9 also find a Kirkendall effect in this alloy using the tracer technique. In the present work, several aspects of the Kirkendall effect in ß brass were further investigated using vapor-solid couples. Two different couples were used, one in which the zinc was diffused into the specimen from the vapor phase and the other in which the zinc was diffused out of the specimen into the vapor phase. Briefly, the existence of a Kirkendall effect is confirmed and it is found that Dzn/Dcu = 3 at about the 46 atomic pct composition in this alloy at 600°, 700°, and 800°C. As a result of the unequal diffusion rates of zinc and copper, volume changes occur and subgrain formation is observed in the diffusion zone. In addition, significant porosity is produced by the precipitation of supersaturated vacancies. Diffusion in this alloy is therefore outwardly similar to diffusion in a brass where these effects are also observed, a Brass Experimental Methods—The use of vapor-solid couples in studying diffusion in a brass has been described in previous articles.6,7 The method briefly consists of sealing a copper specimen with Kirkendall markers initially placed on its surface in an evacuated quartz capsule along with a large zinc source of fine a brass chips and then diffusing the zinc into the specimen through the vapor phase. The zinc concentration at the specimen surface rises rapidly enough to a value near that of the a brass source so that the surface concentration may be regarded as constant during diffusion. Under these boundary conditions, values of the chemical diffu-sivity may be obtained by applying the Boltzmann-Matano analysis to the concentration penetration curve, and the intrinsic diffusivities may be obtained from Darken&apos;s5 equations when the velocity of marker movement is known. The diffusion specimens were made from OFHC copper in the form of disks 3.2 cm diam and 0.5 cm thick with faces surface-ground parallel to within +0.001 cm. Markers in the form of fine alumina particles <0.0002 cm diam were placed on the specimen surface. These specimens were then sealed in quartz capsules along with enough a brass chips of a 30.0 atomic pct Zn composition to keep the source concentration from decreasing by more than 0.3 atomic pct Zn as a result of the loss of zinc to the specimen during diffusion. The quartz capsules which were initially evacuated to a pressure of

Jan 1, 1956

By James K. Hallenburg

INTRODUCTION The delayed fission neutron, or DFN technique for uranium ore body analysis uses the first down-hole method for detecting uranium in place quantitatively. This technique detects the presence of and measures the amount of uranium in the formation. DFN TECHNIQUE DESCRIPTION The DFN technique depends upon inducing a fission reaction in the formation uranium with neutrons, resulting in an anomalous and quantitative return of neutrons from the uranium. Since there are no free, natural neutrons in formation, a good, low noise assessment may be made. There are several methods available for determining uranium quantity in situ. The method used by Century uses an electrical source of neutrons. This is a linear accelerator which bombards a tritium target with high velocity deuterium ions. The resulting reaction emits high energy neutrons which diffuse into the surrounding formation. They lose most of their energy until they come to thermal equilibrium with the formation. Upon encountering a fissile material, such as uranium, these thermal neutrons will react with the material. These reactions produce additional neutrons, the number of which is a function of the number of original neutrons and the amount of fissile material exposed. The particular source used, the linear accelerator, has several distinct advantages over other types of sources: 1. It can be turned off. Thus, it does not constitute a radioactive hazard when it is not in use. 2. It can be gated on in short bursts (6 to 8 microseconds). This results in measurements free of a high background of primary neutrons. 3. The output can be controlled. Thus, the neutron output can be made the same in a number of tools, easily and automatically. There are several interesting reactions which take place during the lifetime of the neutrons around the source. During the slowing down or moderating process the neutron can react with several elements. One of these is oxygen 17. This results in a background level of neutrons in any of the measurements which must be accounted for in any interpretation technique. These elements are usually uninteresting economically. The high energy neutrons will also react with uranium 238. However, the proportions of uranium 235 and 238 are nearly constant. Therefore, this reaction aids detection of uranium mineral and need not be seperated out. Upon reaching thermal energy the neutrons will react with any fissile material, uranium 235, uranium 234, and thorium 232. At present, we do not have good techniques for seperating out the reaction products of uranium 234 and thorium 232. However, uranium 234 is a small (.0055%) percentage of the uranium mineral and thorium 232 is usually not present in sedimentary deposits. When the uranium 235 reacts with thermal neutrons it breaks into two or more fragments and some neutrons. This occurs within a few microseconds after the primary neutrons have moderated and is the prompt reaction. One system uses this; the PFN or prompt fission neutron technique. We don&apos;t use this method because the neutron population is low and, therefore, the signal is small and difficult to work with, accurately. Within a few microseconds to several seconds the fission fragments also decay with the emmission of additional neutrons. Now, with a long time period available and a large neutron population we gate off the generator and measure the delayed fission neutrons after a waiting period. These neutrons can be a measure of the amount of uranium present around the probe. Thermal neutrons are detected with the DFN technique instead of capture gamma rays to avoid some of the returns from other elements than uranium. LOGGING TECHNIQUE The exact logging technique will depend, to some extent, upon the purpose of the measurement. However, the general technique is to first run the standard logs. These will include: 1. The gamma ray log for initial evaluation of the mineral body and for determining the position of the borehole within the mineral body, 2. The resistance or resistivity log for determining the formation quality, lithology, and porosity. 3. The S. P. curve for estimating the redox state and shale content, and measuring formation water salinity, 4. The hole deviation for locating the position, depth, and thickness of the mineral (and other formations), and 5. The neutron porosity curve. The neutron porosity curve is most important to the interpretation of the DFN readings. The neutrons from this tool are affected in the same way by bore hole and formation fluids as the DFN neutrons are. Therefore, we can use this curve to determine effect of the oxygen 17 in the water. Of course, this curve can be used to determine formation porosity. It can also be used to calculate formation density.

Jan 1, 1979

By G. W. Thomas

A mathematical tnodel of forward combustion in an oil reservoir is treated in this paper. The model describes a radial system having a vertical section of essentially infinite thickness, all of which is permeable to gas flow. Combustion, however, is presumed initiated over a limited thickness of the total vertical section. In the interval supporting cotnbustion, the mechanisms of radial conduction, convection and heat generation are taken into account. Above and below the burning interval, heat transport in the radial direction is by cottduction and convection. Vertical heat losses from the ignited interval are accounted for by conduction alone. A general solution is presented for the temperature distribution caused by radial movement of the combustion front. The results show that no feedback of heat occurs into the ignited interval when convection and conduction are acting in the bounding media. Peak temperatures are also 5 to 10 per cent higher than in the case where heat transport in the bounding media is by conduction alone. We arbitrarily define vertical coverage to be that fraction of the total ignited interval which is at 600F above atnbient, or greater, at any given time. The radial distance at which the vertical coverage becomes zero is the propagation range of the combustion front. It was found that an increase in vertical coverage results when the oxygen concentration, fuel concentration or gas-injection rate is increased. Moreover, the combustion front can be propagated 10 to 15 per cent further than in the case where only conduction is acting above and below the ignited interval. INTRODUCTION In the theoretical treatment of forward combustion in a radial system, one of the problems encountered is the determination of the transient temperature distributions caused by an expanding cylindrical heat source. Bailey and Larkin&apos; and Ramey&apos; simultaneously presented analytical solutions to the problem assuming heat transport by conduction alone. In a subsequent publication, Bailey and Larkin3 included the effects of both conduction and convection while treating linear and radial models. In this latter work, however, vertical heat losses were largely neglected. Selig and Couch&apos; dealt with a radial model in which both conduction and convection were acting. Only a limiting case involving vertical heat losses was considered, however. Namely, temperatures on the boundary of the bed of interest were set equal to zero. Solutions thus obtained were representative of a system having a maximum vertical heat flux. Chu5 recently treated a more general case in which a permeable bed was considered bounded by impermeable media. Conduction and convection took place within the bed, and only conduction outside of the bed. The effects of vertical heat losses were included in his study. Solutions were obtained by numerical techniques. This paper is an extension of the theoretical work of other authors pertaining to forward combustion in a radial system. In particular, a mathematical model of the process is treated in which heat generation occurs over a small vertical interval of a larger permeable section. In the interval supporting heat generation, and above and below this interval, the mechanisms of radial conduction and convection are also presumed acting. Heat losses from the ignited interval are accounted for by vertical conduction. An analytical solution for the temperature distribution caused by radial movement of the burning front is presented. The effects of certain process variables are indicated and comparisons with Chu&apos;s results are made. THEORY To render the mechanism of forward combustion tractable to mathematical treatment, we idealize the problem to the extent of assuming continuous reservoir media possessing homogeneous and isotropic properties. The following additional assumptions are implicit in this analysis. 1. The thermal parameters, i.e., heat capacities, thermal conductivities and thermal diffusivities are invariant with temperature and pressure. Moreover, the bounding media possess the same thermal properties as the bed of interest. 2. The temperatures of the porous media and its contained fluids at any point and at any time are equal. 3. The reaction rate between the oxidant gas and the fuel is infinite. This assumption implies that the incoming oxygen concentration instantaneously goes to zero within an infinitesimal distance, i.e., the width of the combustion zone is negligible. 4. The rate of gas injection is constant and corresponds to the average rate throughout the lifetime of the project. 5. The fuel concentration is constant throughout the volume of rock swept out by the burning zone. 6. There is complete burnoff of fuel. This assumption demands that the rate of propagation of the burning front equals the rate of fuel burnoff. In a radial system, with a

By Craig S. Hartley

Expressions are obtained for the energy changes associated with the reaction of (a& (111) slip dislocations on intersecting (110)planes in anisotropic bcc metals. An energy criterion for assessing the likelihood of dissociation of the products of such reactions is also presented. It is found that the "burrier reactions" which form a(100) dislocations at the intersection of two active {110) slip planes are more energetically favorable in metals which exhibit a high value of Zener&apos;s anisotropy factor, A, than those which have a low value. The results are presented in a form which permits the stacking fault energy to be obtained from a measurement of the separation between par-tials in a dissociated configuration. However, until accurate calculations or measurements of the stacking fault energies involved are available, it is not possible to assess the physical importance of dissociated dislocations. In a recent paper,&apos; the energy changes associated with several types of reactions between two slip dislocations, (a/2)(111){110), in bcc structures were calculated.* Isotropic elasticity and the approxima- tion v = -3- were employed. The purpose of this work is to present calculations of the energy changes for many of the same reactions using anisotropic elasticity. The problem of dissociation of a(100) and a(110) dislocations is also considered, and maximum fault energies for which dissociation will be energetically favorable are calculated for several bcc metals. Two general types of reactions are considered; those for which the reactant (a/2)(111) dislocations have long-range attractive forces and those for which the reverse is true. An example of the former is: (a/2)[lll] + (a/2)[lll]-a[l00] while the latter are typified by: (a/2)[lll] + (a/2)[111] -a[011] Only reactants lying in different slip planes are considered; therefore, the products must lie along (111) or (100) directions, which are the intersection of two {llO} planes. It will be assumed that the reactants and products are infinitely long parallel dislocations, since in this case the energy change associated with the reactions is a maximum.&apos; THEORY The self-energy per unit length of a straight mixed dislocation in an anisotropic medium can be written? where b is the Burgers vector, K is an appropriate combination of the single-crystal elastic constants, and R and ro are, respectively, outer and inner cut-off radii of the elastic solution. The energy given by Eq. [I] does not account for any variation of the core energy with orientation. This could be manifested by an orientation dependence of the core radius or, equivalently, the Peierls width, of the dislocation. However, the energy contribution due to this source is expected to be small, and current models of the dislocation core are not sufficiently accurate to justify such a refinement. It has already been shown that for the isotropic case the energy contributions due to nonzero tractions across the cores of the reactants and products exactly cancel one another in the reaction.&apos; Accordingly, it will be assumed that this contribution to the total energy change in the anisotropic case is small. In the subsequent discussion it is also assumed that the core radii of the reactant and product dislocation are the same and that, where stacking faults are formed, the faulted region is bounded by the centers of the partials. Consequently only changes in elastic energy due to the reactions will be considered. When the dislocation is parallel to either the (111) or the (100) directions, K may be written:375 K = (Ke sin2 a + Ks cos2 a) [2] where K, and Ks are the combination of elastic constants corresponding to an edge and screw dislocation lying along the same direction as the mixed dislocation, and a is the angle between the direction tangent to the dislocation line and the Burgers vector. Eq. [2] should not be confused with the isotropic approximation to the variation in energy with line Orientation.6 It should be noted that the essentially isotropic expression for K is a result of the characteristic symmetry of the (111) and (100) directions and is not, in general, valid for other dislocation directions in anisotropic cubic metals. The energy* change for a reaction in which the re- actant and product dislocations are parallel perfect dislocations can be written: where Ep and E, refer to the self-energies of the products and reactants, respectively. For dislocations parallel to (100) and (111) directions, Eq. [3] becomes:

Jan 1, 1969

By P. Greenfield, C. C. Smith, A. M. Taylor

J. E. Harris (Berkeley Nucclear Laboratories, England)—Greenfield et al.11 attribute abrupt changes in slope of their log o/log i curves for heat-treated Mg/0.5 pet Zr alloy (zA) to &apos;atmosphere&apos; locking. It is proposed here that a more reasonable explanation of the apparent strengthening at low rates of strain can be based on precipitation either during the preanneal or during the creep tests. All the tests were carried out above 0.5 Tm where solute atmospheres are likely to be largely evaporated2 and can migrate sufficiently rapidly so as not to impose any &apos;drag&apos; on the moving dislocations. McLean3 has derived an expression for determining the temperature Tc above which, due to the high-migration rate of the atmospheres, Cottrell or Suzuki locking can play no part in determining creep strength. This expression, which holds for an applied shear stress of not greater than 5 X 107 dynes per sq cm is: Tc/Tm= 7/6.8 - log10? where i = secondary creep rate The values for T, corresponding to the maximum and minimum reported creep rates at each temperature have been calculated from the data of Greenfield et al. These are given in Table VII. All the test temperatures were above T,, the margin being greater for the higher temperatures and for the lower strain rates where the breaks in the log s/log ? curves occurred. Dorn and his collaborators14, 17 have studied systematically the effect of solute hardening on the creep properties of an A1/3.2 at. pet Mg alloy. In the temperature range where strain aging occurred in tensile tests, abnormally high-activation energies for secondary creep were obtained but at temperatures above 0.43 Tm, solute alloying did not have any effect on the creep parameters. Moreover, there have been no reports of any strain aging phenomenon during elevated temperature tensile tests with ZA material.18 Instead of the observed strengthening being due to atmosphere locking, it is now proposed that precipitates play an important role in enhancing the creep strength of the material. There are two possibilities—precipitation of zirconium hydride during the high-temperature preanneal and/or precipitation of the hydride or a-zirconium during creep. On the basis of the former the results can be interpreted in terms of a critical stress being necessary to force the dislocations through or over preexisting precipitates. From the latter, if the strengthening is due to pre- cipitation during the test then hardening should be associated with a critical strain rate. At low rates of strain, time is available during the tests for precipitation to occur either directly onto dislocations (thus pinning them) or generally throughout the matrix (which would impede dislocation movements). Examination of the data of Greenfield et al. suggests that both mechanisms may be operative since they observed precipitation during creep and also found that their alloys exhibited high-creep strength in the early stages of the low-stress tests, i.e., before creep-induced precipitation had time to occur. It is not easy to understand why they considered that precipitation of zirconium hydride is unlikely to occur at 600°C while it can take place in tests in air at as low a temperature as 200°C. Precipitation of the hydride during the preanneal cannot be ruled out merely on the basis of metallographic examination. Hydride precipitates in ZA type alloys are very small and can only be accurately resolved in the electron microscope.9 For example, in this laboratory20 hydride platelets with major dimensions <(1/10) µ have been observed by electron transmission through thin film specimens of hy-drogenated ZA material. Complex interactions between dislocations and such particles are illustrated in Fig. 12. Additional evidence for precipitation during pre-annealing is provided by the data presented in Greenfield&apos;s Fig. 1 and Table IT. These show that the creep strength at 200o and 400°C increases with the time of preanneal at 600°C. Such increases cannot be explained on the basis of increases in grain size alone for further improvements in strength were observed when the material was annealed for longer times than that required to stabilize the grains. Although the main discussion is confined to ZA material, similar arguments can be used against the strain aging hypothesis proposed to explain the binary Mg/Mn alloy data. In this case no precipitation is possible during the preanneal, but precipitation-hardening during creep can occur.

Jan 1, 1962

By I. Fatt

A recently developed system for measuring electrical resistivity of liquids without use of electrodes offers some interesting possibilities in electric logging technology. The equipment as supplied by the manufacturer is satisfactory for continuous mud logging on a drilling rig or for measuring mud or filtrate resistivity in the laboratory. A simple modification of the commercially available instrument makes it suitable for measuring resistivity of core samples in the laboratory. The continuous measurement of mud resistivity on a drilling rig is a convenient means for detecting mixing of formation water with the drilling mud. Such information is useful to the geologist, the mud engineer and the logging engineer. However, continuous mud resistivity logging by conventional electrode-type resistivity cells is beset with difficulties. The mud, sand and rock chips abrade the electrodes, thereby changing the cell constant and eventually destroying the cell. Also, additives and crude oil in the mud may poison the electrodes by coating them with a nonconductive material. An electrode-type resistivity cell. therefore, may give erroneous readings under certain conditions. Electric logging companies circumvent the electrode poisoning problem by using a four-electrode resistivity cell for measurement of mud resistivity. In this cell, change in electrode area does not change the cell constant. However, the four-electrode cell is difficult to adapt for continuous reading and does not solve completely the problem of electrode abrasion by the sand and cuttings in the mud. The measurement of electric logging parameters on core samples in the laboratory encounters some of the same problems discussed in connection with mud logging. Ideally, the electrical resistivity of a core sample should be measured by placing platinum black electrodes in direct contact with the plane ends of a cylindrical or rectangular sample. Platinum black electrodes however, are much too fragile and easily abraded to be brought in contact with a rock sample. Also, oil or other constituents in the fluid contained in the sample will poison platinum black. In practice, gold-plated brass electrodes, in an AC bridge circuit operating at about 1,000 cps, are used for routine core analysis. For more precise work in research studies, a four-electrode scheme is used.&apos;,&apos; Preparation of the samples for the four-electrode method is much too involved for routine core analysis. An apparatus for measuring resistivity of liquids without use of electrodes was described by Guthrie and Boys3 in 1879. They suspended a beaker, containing the electrolyte, by a torsion wire and rotated a set of permanent bar magnets around the vessel. The eddy currents induced in the electrolyte reacted against the rotating magnetic field to develop a torque, which was measured as a deflection of the torsion wire. In 1879 this method could not be made precise or convenient because of the lack of strong permanent magnets. The writer described a very greatly improved apparatus similar to that of Guthrie and Boys, but it was not suitable for continuous measurements or core samples.&apos; Many electrodeless resistivity devices using radio frequency current are described in the literature.5, 6 These generally are suitable only for noting the end-point in a chemical titration. They do not measure resistivity, instead measuring a complex quantity which includes the dielectric constant and the magnetic permeability. The first description of the apparatus to be discussed in this paper was given by Relis.7 Improvements and modifications are described by Fielden,s Gupta and Hills,> and Eichholz and Bettens.10 DESCRIPTION OF APPARATUS The apparatus used in this study is based on the principle that the solution under measurement can form a loop coupling two transformer coils, as shown in Fig. 1. For a fixed AC voltage applied across Coil A, the voltage appearing across Coil B is a function of the resistance of the liquid-filled loop. The details of the voltage generating and measuring circuits are given in Refs. 7, 8, 9 and 10. A block diagram of the equipment is given in Fig. 7. Special features worth mentioning are the operating frequency of 18,000 cps and the automatic temperature compensation which results in the given resistivity readings being automatically correlated to 25°C. The liquid loop supplied by the manufacturer, shown in Figs. 1 and 2, was modified for use in core analysis (Fig. 3). The core sample under test is substituted for a section of the original loop. As shown in Fig. 3, the unit accepts only plastic-mounted cylindrical core specimens. A Hassler-type sleeve easily can be designed for the unit if unmounted cores are to be measured. EXPERIMENTAL PROCEDURE MUD LOGGING A simulated mud line was set up in the laboratory.

By B. G. Matson, M. A. Whitfield, G. R. Dysart

This paper describes the development of u computer program to calculate changes that occur in the length of tubular goods due to temperature and pressure changes during stimulation operations. Due to the numerous variables involved and the uncertainty of all static and dynamic conditions that could exist, it becomes a staggering task for individuals charged with completions to perform the necessary mathematical calculations. The computer program permits advance calculations for several sets of conditions. INTRODUCTION In the Delaware basin of West Texas alone, 50 wells were contracted or drilled to 15,000 ft or deeper in 1965. Deep well activity is continuing in this and other areas on an expanding scale. Many of these deep wells require extensive stimulation for successful commercial production, and during these operations, pressures and temperatures are encountered that have a pronounced effect on the length of tubular goods. This length change during a large-volume, high-pressure stimulation treatment utilizing fluids considerably cooler than bottom-hole temperature can be of such a magnitude that permanent damage to casing and tubing will result unless mechanical design, pressures and fluid temperatures are evaluated and controlled. These pressure and temperature effects can be calculated. However, the process lends itself well to computer solutions because of the mathematical nature of the problem and the calculating hours involved in arriving at an answer. The engineering-hour demand becomes more severe as tapered strings are involved. On initial treatments on a given well, surface pressure and injection rate conditions are unknown, and offset well conditions have not proven to be a reliable method for making predictions. For these reasons, it has become rather standard procedure for operators to compensate for these uncertainties by placing unnecessary pressure and fluid temperature restrictions on stimulation design. On a number of occasions treating fluids have been preheated to as much as 160F as a means of compensating for thermal contmction resulting from pumping cool fluids. The maintenance of packer seals has been treated by Lubinski, Althouse and Logan&apos;,&apos; and the problem of therma1 effects on pipe has been explored by Ramey." These works were expanded and the results made applicable to everyday oilfield terminology before submitting them to computer programming. The pressure and temperature effects on tubing movement previously mentioned occur simultaneously as fluid moves through the pipe. The pressure changes, for purposes of explanation, are categorized here as to the various effects these pressures have on a tubing string. These divisions are (1) the piston-like results of forces acting on horizontal surfaces exposed to pressure, (2) swelling or ballooning of the tubing along its entire length due to the forces of pressure acting against the tubing walls, (3) the elongation of tubing due to frictional drag and (4) corkscrewing of the pipe due to internal pressure. Thermal changes are also of great importance, as their results may be more significant than any of the pressure effects. Steel is an excellent conductor of heat and the earth is a relatively poor conductor. It has been calculated that pipe temperatures at depths of more than 20,000 ft approach within as little as 25" the temperfature of the surface fluid after pumping for 2 hours, or a drop in temperature in some treatments of more than 220F. The equations presented in this paper were developed for computer programming and simplicity of input information; therefore, numerical constants such as Young&apos;s modulus for steel (28 X 10\ si), the coefficient of thermal expansion of steel (6.9 X 10."IF) and Poisson&apos;s ratio for steel (0.3) are included with unit conversion factors. The moment of inertia of tubing cross-sectional area with respect to its diameter was changed to a constant times (D&apos; — d&apos;) where D is outer diameter and d is inner diameter. Units in the equations are length in feet, diameter in inches, density in pounds per gallon, pressure in psi, rate in barrels per minute and time in hours. PISTON-LIKE REACTIONS A change in tubing internal dimensions and the exposure of other horizontal surfaces to different pressures on the inside and outside of the tubing result in a reaction much like a piston under pressure. Such is the case when the internal diameter changes in a combination string of pipe, when seals of a slick joint assembly are subject to pressure and in the end effects of a tubing string. The change in tubing length due to the piston effects of a slick joint packer is affected by the various diameters involved, the tubing pressure Ap,, the casing pressure ,Ap,, length of pipe L, densities of fluid in the tubing before and during pump-

By S. J. McCarroll

Fig. 1—The belt shown at right carries filter cake to mixing station over calciner. Crude ore conveyors appear in right background. THE Three Kids mine, some six miles east of Henderson, Nev., is in a typical southwest desert area, with high dry summer heat and cool to cold winter seasons. The manganese deposit was located during World War I.&apos; During this period 15,000 to 20,000 tons of ore assaying up to 41 pct manganese were shipped. Interest in the deposit was not revived until the middle thirties, when experiments on the ore were initiated. Test work indicated possible recovery of only 70 pct by flotation, but in 1941 additional work was done at the Boulder City pilot plant of the U. S. Bureau of Mines and also by M. A. Hanna Co. As a result, the Manganese Ore Co. was formed and a plant utilizing the SO2 process was constructed. Numerous operation difficulties ensued, and the plant. was closed when the manganese situation in the country eased. In 1949 Hewitt S. West initiated negotiations to acquire the plant. In 1951 Manganese, Inc., was formed and contract entered into with the General Services Administration to supply 27 million units of metallurgical grade manganese in the form of nodules to the national stockpile. A second contract was made to upgrade 285,000 tons of stockpile ore. Test work was undertaken by the Southwestern Engineering Co. and likewise by the Boulder City pilot plant at the U. S. Bureau of Mines. Results obtained indicated the commercial feasibility of the flotation process. Construction of the plant, which is shown in Figs. 1 and 2, was started in June 1951, and operations on a break-in basis began in September 1952. Apart from the usual starting difficulties two major disasters caused serious setbacks, one a kiln failure in February 1953, and the other a fire that destroyed the flotation building in June of the same year. The nodulizing section of the plant resumed operation in November, and the flotation section in January 1954. The ore minerals are chiefly wad,* with minor amounts of psilomelane, and occur in sedimentary beds of volcanic tuff. The ore is overlain with beds of gypsum which outcrop or may be covered with surface gravel. Intermediate beds of red and white tuff occur frequently with lenses of red and green jasper and stringers of gypsum and calcite. Small amounts of iron are present; lead content averages about 1.0 pct and minute amounts of copper and zinc are found. Barite, celestite, and bentonite are present. Since these are made up of minute asicular crystals, moisture content is very high, averaging about 18 pct. Ore reserves have been estimated at 3 million tons averaging 18 pct Mn2 and up to 5 million tons after grade is dropped to 10 pct Mn. A good part of the orebody was stripped of overburden by the previous operating company . Approximately 50 pct of the ore, representing more than 60 pct of the manganese, can be mined by open-cut methods. A system for underground min- . ing has not yet been decided on. Open-cut mining with benches of 20 ft has proved satisfactory. Although the ore is soft and appears dry and dusty it has a certain resilience, probably due to the porosity and moisture which makes drilling and fragmentation difficult. Wagon drills have been abandoned in favor of the Joy 225-A rotary drill which will put down a 43/4 -in. hole at the rate of 2 ft per min. Holes are spaced in a pattern with 8 to 9-ft centers. Forty percent powder has been used, but better breaking to 2-ft size is obtained with low velocity bag powder of 30 pct strength. Loading is done with one 21/2-yd shovel, and cleanup follows with one D-7 bulldozer. The ore is hauled with Euclid trucks about 1000 ft from the pit to a blending pile, where the daily mine production is spread in layers by bulldozing until approximately one month&apos;s mill feed is accumulated. A new pile is then started and mill feed is drawn from the first pile by one 13/4-yd shovel and Euclid trucks, with a haul of approximately 500 ft. Mining is performed by an independent contractor with engineering and supervision by the company staff. Early test work indicated that the manganese could be floated with soap, a wetting agent, and fuel oil to give a recovery of better than 75 pct with a grade of 43 pct Mn. The concentrate when nodulized with coke would upgrade to 46 pct Mn or over, and the lead volatilized to 0.6 pct residual.

Jan 1, 1955

By J. H. Swisher

The solubility of graphite in CaO-S2O2-Al,O3 slags was measured by equilibrating slag samples with graphite crucibles and CO gas. Carbon contents as high as 2 ut pct were obtained in CaO-saturated, CaO-A1,O3 slags, and 1.3 wt pct in slags of the composition CaO.Si0,. Although the observed conditions for Sic formation were in agreement with those predicted from thermodynamic data, CaC, was found to form at a lower temperature than predicted frotn thermodynamic data. From measurements of the equilibrium carbon content as a function of CO Partial pressure, it was found that carbide ions dissolve in CaO-A12O3 melts with a valence of minus two. The carbon content increased with CaO concentration in Ca0-Al,O3 melts and increased with SiO, content along the CaO&apos;AlO3-CaOSi0 join in the ternary system. When solid CaC2 was added to CaO-A12O3 and CaO-SiO2-A12O3 slags, it was found that one of the oxides in the slag was reduced by the carbide (Al2O3 in the forrner and SiOz in the latter). In electric furnace steelmaking, a double-slag practice is frequently used to meet alloy specifications. Initially a flush slag, which is oxidizing in nature, is used to remove phosphorus and carbon from the steel bath. Later in the refining period, the flush slag is replaced by a highly reducing carbidic slag. When calcium carbide is formed in or added to a finishing slag, the slag is effective as a desulfurizing agent and also permits alloying elements such as chromium, vanadium, and tungsten to be added to the slag in the form of oxides. The oxides are readily reduced by calcium carbide, thereby minimizing the use of expensive ferroalloys. More work has been done on the thermodynamics of silicon carbide in slags than on calcium carbide. Baird and alor&apos; and Kay and alor&apos; determined the free energy of formation of Sic by measuring the partial pressure of CO in equilibrium with solid silica, silicon carbide, and graphite. Using a similar technique, they determined SiOz activities in CaO-SiOz and Ca0-Si0,-A1203 slags. Rein and chipman3 also determined the free energy of formation of Sic using slag-metal equilibrium measurements. A literature survey has uncovered only one experimental study of the behavior of CaC, in slag systems. Shanahan and cooke4 report the results of some preliminary experiments on the solubility and stability of CaC, in a CaO-A1,03 and a Ca0-Si0-A1,03 slag at a temperature of about 1500". The carbon solubility as CaC, in a slag containing 50 pct CaO and 50 pct A1203 was reported to be 0.6 pct. They also review earlier work on the binary CaO-CaC, system. A eutectic exists in this system, but various investigators disagree on the eutectic temperature and composition. eal has given an explanation for carbide furnace erruptions in terms of the thermodynamic properties of CaC,; his analysis is not based on experimental data, but on compiled data for the free energies of formation of CaC, and CO.&apos; , These data for steel-making temperatures are all extrapolated from the results of low-temperature measurements. In the experiments described in this paper, slag samples were equilibrated with graphite crucibles and with mixtures of CO and argon or with CO gas at 1 atm total pressure for measurement of the carbon solubility. Most of the work was done on Ca0-A1203 binary slags, although in some experiments CaO-SiO, and Ca0-Si0,-A1,03 slags were used. EXPERIMENTAL Slag samples of the desired composition for the solubility measurements were obtained by blending pre-fused master slags. The master slags were prepared by fusing mixtures of reagent-grade CaC03 with either A1,03 or Si0, in a graphite crucible. The master slags were crushed, then decarburized in air in a muffle furnace at 1200O C. A schematic diagram of the apparatus is shown in Fig. 1. The source of carbon for the solubility meas-

Jan 1, 1969

By V. Steve Reed, Ed L. Reed

The in situ leach mining process generates a waste stream that is high in sulfates, total dissolved solids, and radium 226. During the mining phase, the volume of the waste stream is relatively low and consists primarily of the bleed stream. During the restoration phase, larger volumes of waste water are generated. These waste streams require environrnentally sound disposal. The low net evaporation rate in the Coastal Bend area precludes pond evaporation as a feasible disposal alternative. Reverse osmosis is a practical method of reducing the volume of the waste water handled, but the concentrated waste stream from the reverse osmosis unit must be disposed properly. Deep well injection into highly saline reservoirs is considered a sound method of disposing of the liquid waste generated by in situ mining in the Gulf Coast uranium district. Thirteen injection wells have been permitted to serve the disposal needs of the leach mining industry in Texas. Of these 13, 11 have actually been drilled. Seven applications are pending. The injection zones for the permitted wells range from depths of 3050 to 6200 feet. Pressure limitations imposed on these wells range from 500 psi to 1350 psi. The following criteria are used to determine the desirability of a disposal well site: 1. A minimal number of nearby, improperly plugged borings which penetrate the disposal zone; 2. Minimal crustal disturbance; 3. Sufficient salinity of the water contained in the disposal zone; 4. Protection of oil and gas producing zones; and 5. Sand of sufficient permeability and areal extent to handle the desired volume without fracturing the reservoir. 1. Improperly plugged borings: During the early part of the century, oil wells, gas wells and test holes were drilled using cable tool equipment, often with a minimum amount of surface casing. Production casing, when it was set, was often partly removed when the holes were abandoned. Thus, wells drilled prior to 1940 frequently have less than 100 feet of surface casing and either no production casing or the upper part of the production casing removed. Additionally, these holes are often plugged only with mud. The close proximity of these holes to an injection well location are a concern in that they can provide an avenue for injection-depth fluids to migrate up the bore hole and jeopardize shallower fresh water reservoirs. Usually, where there are more than 6 or 8 poorly plugged borings in a 2 1/2 mile radius of the well site, it is preferable to examine deeper zones for disposal well potential. The deeper zones are especially attractive where the borings are not in a cluster, which renders monitoring more difficult. Often, even the deeper disposal zones are penetrated by a few improperly plugged borings. When this condition arises, the potential for leakage through the borings can be addressed in the following ways. a. Demonstration that the static head in the boring is higher than the anticipated increase in bottom hole pressure generated at the boring by the disposal well. A 100 psi differential between these two pressures is recommended. The calculated increased pressure at a boring caused by injection should be refined using annual bottom hole pressure measurements in the disposal well. Figure 1 illustrates an injection pressure map which can be overlain on the oil well map to determine the anticipated increase in pressure expected at each oil, gas or abandoned hole. b. Shallow ground water monitoring. A shallow monitor well is drilled next to the boring and both pressure and quality measurements are made periodically in the shallow well. c. Disposal zone monitoring. Recently there has been a tendency for regulators to require disposal depth monitor wells instead of shallow well monitoring. We consider disposal depth monitoring to be a less effective method of monitoring because it provides only indirect evidence of potential problems. Assumptions have to be made for the unplugged borings, such as mud weight, that are not addressed by the disposal zone monitoring program. There is little improvement with this system to that discussed in "a" above. A shallow zone monitoring program, however, yields direct evidence of a developing problem with an unplugged boring. Leakage by the boring will be detected quickly by an abnormal increase in pressure in the shallow well. Quality monitoring will detect upward migration of poor quality fluids. The pressure data provide an early warning of impending leakage; the quality monitoring will detect actual fluid migration.

Jan 1, 1980

By D. A. Augenstein, L. V. Amundson

Operators of coal preparation plants use equipment such as large-capacity dump trucks and bulldozers to haul, spread, and compact refuse material to conform to federal and state regulations governing the disposal of solid waste. For example, federal regulations require that refuse be spread and compacted in layers not more than 0.6 m (2 ft) thick. If the refuse layers or piles have poor load-bearing characteristics, movement of equipment over them becomes extremely difficult. The increasing cost and limited space for the construction of settling ponds extensively used for fine refuse disposal are leading to the growing practice of dewatering the fine refuse by means of vacuum disk filters and combining the resulting filter cake with coarse refuse for waste bank disposal. However, this filter cake usually contains more than 25% moisture. Therefore, when it is combined with coarse refuse, the moisture level of the total refuse may become high enough to impair the load-bearing strength of the refuse. Precisely this problem and the attendant difficulties of moving heavy equipment arose when vacuum disk filters were installed at a preparation plant in West Virginia. Combining the moist filter cake with the coarse refuse generally results in a 12% moisture level for the total refuse at this plant. At this moisture level, the refuse can still be handled with some dif¬ficulty by the equipment. However, the problem has frequently been compounded after rains. The experimental program described in this paper tested the following methods of improving the load-bearing properties of coal refuse: moisture reduction, addition of crushed coarse refuse, addition of fly ash, addition of lime, and addition of a mixture of lime and fly ash. In terms of a balance between economic and technical considerations, the most effective method was demonstrated by laboratory and plant tests to be a 2% to 5% addition of lime. Test Program During formulation of a test program aimed at improving coal refuse stability, a number of treatment techniques were selected for evaluation of their effect on refuse load-bearing characteristics. The reduction of refuse moisture was the first technique considered, since moisture content plays a key role in the bearing strength of a bulk solid. The reasoning was that a very small reduction in refuse moisture, provided it could be accomplished with minimal effort and cost, would be sufficient for eliminating refuse disposal problems most of the time. At the same time, it was recognized that periods of rainy weather would offset moisture-reduction measures. Other techniques selected for evaluation because of their potential for improving refuse-bearing strength at reasonable cost were: addition of crushed coarse refuse, the addition of fly ash, and the addition of lime. A simple one-dimensional laboratory compaction test was designed for evaluating the effect of each of these techniques on refuse-bearing strength. Those techniques that gave best results in the laboratory would then be tested in the preparation plant in West Virginia. Laboratory Tests The laboratory test for evaluating each of the techniques involved the application of weight to a load module placed on a refuse sample in a container. The distance the load module sank with an increasing amount of applied weight was measured, and the relationship between module displacement and loading was obtained. The refuse container was large enough to minimize the influence of wall effects, and to decrease the effect of the container bottom, a test was terminated when the load module sank to about three fourths the depth of the container. Initially, an attempt was made to conduct compaction experiments with samples of total plant refuse. However, the presence of + 0.13 m (+ 5 in.) material in the refuse interfered with the mechanics of the test, and the large amount of material required for a representative sample made testing extremely tedious and time-consuming. To avoid this problem and because it was believed that only the fine components of the refuse were the major cause of the stability problem, tests were conducted with 13 mm X 0 (1/2 in. X 0) material from the total plant refuse. The equipment consisted of a 0.46 m (18 in.) cubic container, a loading module with 62 cm2 loading area, weights totaling 450 kg, and a portable concrete mixer for combining water and additives with the refuse. Refuse samples of about 110 kg dry weight were used for each test. Experimental compaction test data were evaluated by plotting the linear displacement of the load module vs. loading. During compaction tests, the vertical displacement of the load module was measured at each loading value. The plot of

Jan 1, 1980

By Chas. A. R. Lambly

In the extreme northeast corner of the State of Washington, on the Canadian border, lies the Metaline mining district. This district is old in history, but young in production. Geology The Metaline district is a zinc-lead area of the replacement type in dolomite and limestone. The ore bodies of the Josephine horizon are in many ways similar to the ore bodies of the famous Tri-State zinc fields. The beds are faulted and folded and have varying low dips in varying directions, and underlie large areas of the district. History Production started in 1927 on a very limited basis. The property is now mining and milling 700 tons per day. The mine is opened by adit tunnels and a vertical shaft. As the ore horizons gained depth, it was necessary to sink inclines to follow the ore horizon (see Fig 1). From 1927 to date, approximately 600,000 ft of diamond drill was put down This work indicated that suficient tonnage existed to justify a redesigning of the whole operation, surface and underground. After four years of general study, the following program was planned: 1. A new mine entrance, which would be an incline, that could follow the ore body down at whatever pitch was necessary. The incline will be equipped with conveyors for the moving of ore and waste to the surface and with tractor-type locomotives for man and supply transportation. 2. The new incline also required a new type of mining which was developed and is now in use. It is called contour mining and will be described in a future paper. 3. The new incline exit would necessitate the moving of the mill and mine shops across the Pend Oreille River. This part of the program is now underway. The Incline The sinking of the incline was to start as soon as World War II ended and was as follows: The first leg of the incline was to be sunk from the surface 1600 ft on a 17" slope. The collar and first level at elevation 2180 ft, the second level at elevation 2000 ft, the third level at elevation 1875 ft, and the fourth level at elevation 1700 feet. From the 1700 ft elevation the incline was to flatten out to 12" for 400 ft to give the necessary depth for the ore pockets below the 1700 ft level and the necessary clearance for future sinking (see Fig 1 and 2). Due to lack of manpower in 1946, the program was changed and was as follows: A drift was driven from the old mine workings on the 1700 ft elevation in an easterly direction. At 1300 ft the drift was turned N 50" E and at this point a raise was driven 180 ft on a 50" slope. This raise intersected the Josephine horizon and commercial ore was encountered. At the 2000 ft mark, a main raise was driven, 245 ft on a 50" slope, and the 1875 ft elevation was cut. Exploration drifts were started on this level and production followed on a limited basis. The main drift at the 2500 ft point was turned N 35" E and ran parallel to and 10 ft east of and under the proposed incline line. At the proposed intersection of the drift and incline on the 1700 ft elevation, it was planned to raise the incline to intersect the 245 ft raise and to continue on to the surface, a distance of 1600 ft. When this proposed intersection point was reached, a heavy flow of water, approximately 800 gpm, was encountered and all work on the main drift face was stopped. This water flow flooded the main pump station in the old mine and the two lower levels with approximately 20,000,000 gal of water. The water was controlled and finally drained from the cave areas and lower levels after six months of pumping. After the heavy flow of water was encountered in the main heading, it was decided that the incline would have to be started from the surface, as originally planned, so that too much time would not be lost. The surface overburden had to be removed, a total of 6000 yards. A temporary dry house for 6 men was built. An 8 in. churn drill hole was intersected in the first raise driven from the 1700 foot elevation tunnel. Air and water lines were placed in this hole, and air and water were delivered to the collar of the incline from the mine working. The incline started down at 15 ft wide and 7 ft high through the Leadbetter slates. After sinking 4 sets, it was

Jan 1, 1950

By H. M. Zoerb

Based on the belief that operating details are a definite contributing factor to major economies, this paper traces the development of crushing cavity design in Symons cone crushers to attain maximum liner utilization. Wear rates are analyzed and compared in this presentation and drawings illustrate succeeding design changes. IN these times of rising labor and material costs, it has become more and more necessary that attention be paid to some operating details which, in their obscurity, may he the key to major economies. Liner wear in crushing cavities of secondary and tertiary crushers can become an appreciable cost item when the material to be crushed is hard and abrasive. This item of cost not only includes the value of the crushing members, but also more intangible costs such as labor and lost production due to more frequent replacement. The variables which are encountered in ores and minerals to be reduced; the design of plant and machine application; the sizes, shape, and fineness, characteristics of the crushed product; the moisture; hardness; friability; and abrasiveness of the material to be crushed are all influencing factors which must be taken into consideration in the selection of a crusher, and particularly in the design of crushing cavity and liners to be used in a crusher. Through a research program undertaken in cooperation with many operators of Symons cone crushers a new approach to crusher cavity design was made, resulting in the development of liners for specific operations which showed: 1—maximum utilization, as high as 70 to 80 pct of original weight of metal, and 2— maximum capacity of unit during the greater portion of its life. It has been found that liners so designed for a given operation will show added economies in power consumption, maintenance, and general wear and tear on the crushing unit. Initial work in the so-called tailoring of crushing cavitles was begun on the tertiary or fine crushing units where as a rule reduction ratios were low, varying from 3 to 6. Parallel or sizing zones in the lower portion of the crushing cavity were too long, resulting in a tendency to pack. It was found that very little additional crushing was done in the parallel zone after the initial impact in that zone and that a relatively small amount of&apos; additional crushing was done by attrition, which required very careful feed control. A small amount of over-feeding would result in packing which not only consumed power but caused unnecessary liner wear as well. The illustrations which follow in this discussion will show only contours of crushing cavities, and for purposes of simplification the cavities will be considered only in their closed position. The first step, therefore. was to reduce the sizing zone to a minimum. This was done by removing the lower portion of the liner as shown in Fig. 1. The result of the change was a saving of 15 to 20 pct in liner cost, less power consumption, with no change in capacity. This change in design, while an improvement, did not go far enough. As wear took place, the change in the liner was not uniform throughout its entire length, resulting in a restriction of the feed opening and thereby loss of capacity. Furthermore, progressive wear of the liner had the effect of lengthening the parallel zone until finally the entire crushing cavity was all parallel zone, see Fig. 2. It is obvious from the reduced feed opening of the worn liner that the ability of the machine to receive material is lessened considerably. Furthermore, the long parallel zone with its worn, irregular profile did not operate at its highest efficiency. The first attempt to overcome this difficulty was carried out on a 5 1/2-ft crusher installed in a plant producing roofing granules. The material being crushed was a very hard graywacke and the crusher was closed-circuited with a screen having .232-in. slotted openings. A radical change in contour was developed, as illustrated in Fig. 3. Equal wear lines on both concave and mantle are designated 1, 2, 3, etc. The method of development of this contour is as follows: Since adjustment for wear is vertical, corresponding intersections of wear lines and vertical lines developed concave and mantle contours which maintained equal but lengthening wear surfaces in the parallel zone. The ideal contour, of course, is one in which the length of the parallel zone remains constant, but because of present foundry practice and heat treating characteristics this is impossible.

Jan 1, 1954