Search Documents

By F. W. Jessen, C. A. Johnson

The effect of treatment with ferrochrome lignosul-fonate on both sodium and calcium bentonites has been examined. In the early stages of treatment it appears that some base exchange of iron and chromium for sodium may occur with the sodium bentonite. Such exchange appears specific for exchange of sodium ions when the calcium ion concentration represents 40-5.5 per cent of the total exchangeable cations, and when additions of lignosulfonate are less than 1 lb per bbl. Adsorption appears entirely physical above 1 lb per bbl treatment level for all concentrations of calcium studied. Gel strength and plastic viscosity of both calcium and sodium bentonite systems were reduced with treatments of ferrochrome lignosulfonate up to 2 Ib per bbl, the greatest reduction occurring within a range of calcium concentration of 40-5.5 per cent of the total exchange capacity of the clay. INTRODUCTION The problem of control of viscosity and gel strength of drilling fluids by the action of thinners or dispersants has been studied by many investigators.1-7 In addition, much work has been done on formation of gel structure in clay suspensions. However, gel formation and structure still are incompletely understood, and the use of the various dispersing chemicals is based, to a large extent, on data almost entirely empirical in nature. In recent years the lignosulfonates have become increasingly important in the treatment and control of drilling fluids. More specifically, ferrochrome lignosulfonate has found rather wide acceptance, particularly in calcium systems.5-7 Lignosulfonates are refined lignin products made from spent sulfite liquor from which the fermentable sugars have been removed.15 The exact structure of lignin is not known; however, it is believed to be a phenolic propane type polymer which may exist as a branched chain or cross linked structure. The molecular weights of lignosulfonates probably range from 300 to 100,000 or more.15 A better understanding of the mechanism of adsorption of dispersants is essential before improvement and development of characteristics of drilling fluids and drilling fluid control is possible. This investigation was undertaken to determine the action of ferrochrome lignosulfonate on sodium and calcium montmOrillonite' LABORATORY INVESTIGATION A Stormer viscosimeter and Fann V-G meter were used to measure viscosity and gel strength. A Zeiss spectrophotometer was used for analysis of Fe and Cr and the flame attachment was employed in the analysis of Na, Ca and Mg. A General Electric X-ray diffraction unit utilizing Copper Ka radiation and a Ni-filter was utilized in the X-ray studies. PROCEDURE Two systems were studied. Predominately sodium clay, obtained from Wyoming, and a predominately calcium clay from Texas were used. These particular samples were chosen because of the extensive work of characterization completed by Mungan. Ionic base exchange capacity determined by flame photometry and total exchange capacity by the Kjehldahl method were obtained experimentally. A 7-per cent suspension of the sodium clay and a 20-per cent suspension of the calcium clay in distilled water were prepared by mixing with a high-speed mixer. The suspensions were allowed to stand for two weeks for complete hydration. Calcium chloride was added to portions of the sodium and calcium cla suspensions to obtain suspensions varying in Ca++ concentration as shown in Table I. A series of treatments was run with 500-ml portions of the original suspensions using a ferrochrome lignosulfonate. Treatment was carried out in the same way with each of the suspensions of varying Ca concentration. Viscosity and gel strength were measured and a filtrate obtained at each treatment level. Ten ml of filtrate were diluted to 50 ml, and aliquot portions of the 50 ml were taken for the Na, Ca, and Mg analysis by the flame photometer. The pH of these filtrates ranged from 7 to 7.3. Standard

By G. W. Form, W. A. Spitzig

The effects of hydrogen and vacuum shtering treatments on the physical and mechanical properties of arc plasma-sprayed tungsten were inuestigated. Temperatures examined ranged from 3000" to 4000°F in vacuum and 2000" to 3000°F in hydrogen for both single and duplex sintering cycles. Densities of 92 pct of theoretical density were obtained when a long-time hydrogen treatment at 2000°Fpreceded sintering in vacuum at 4000°F for 4 hr. This cycle also produced the highest ualues for modulus of rupture and bend angle. The results of this investigation point out the desirability of using a low-temperature long-time hydrogen treatment prior to a high-temperature vacuum sinter for arc plasma-sprayed tungsten. ADVANCES in the development of arc plasma-generating equipment have provided a high-temperature heat source that makes the fabrication of tungsten shapes possible by a metallizing process. Tungsten in the as-sprayed condition is very brittle. It has a density between 80 and 85 pct of theoretical density, a lamellar structure with elongated pores, and a high interstitial impurity content. To improve these properties, sintering treatments can be applied to the as-sprayed material, similar to those used for the densification of compacted tungsten powder. However, in view of the differences in the density and microstructure of as-sprayed tungsten as compared with compacted tungsten, responses to sintering were expected to be different. EXPERIMENTAL PROCEDURES The tungsten powder used in this investigation had a particle size varying from 3 to 13 p with an average diameter of 8p. The impurity level was less than 0.1 pct. The arc plasma spraying was done with an F-40 Thermal Dynamics Corp. plasma jet. Spraying was performed in air and thus required cooling of the substrate by an air blast in order to minimize oxidation. The spraying parameters employed in the fabrication of all specimens are listed below: Power input, kw 12 Arc-gas flow, cfh 95N2 + 5H2 Powder feed rate, g per min 33 Powder carrier gas flow, cfh ION, Spray distance, in. 3 Traverse rate, in. per min 30 Mandrel speed, rpm 100 Nozzle orifice, in. 7/32 These values of the spraying parameters correspond to optimum conditions ascertained in a previous study. Sintering was conducted at 3000°, 3500, and 4000°F in vacuum (< 0.1 Hg), and at 2000 and 3000°F in hydrogen. Duplex sintering treatments investigated are listed in Table I together with the designations that will be used for reference throughout this paper. The samples were fabricated by spraying onto a copper mandrel which was removed prior to sintering. The specimens used for the sintering analyses had the shape of small hollow truncated cones 1 in. high with an inside diameter varying from 0.500 to 0.125 in. and a wall thickness of 1/8 in. Specimens for bend testing were taken from hollow hexagonal prisms 1-1/2 in. high with a 1-in. diam across the flats and a wall thickness of 1/8 in. The bend-test specimens were ground to the dimensions 0.085 by 0.350 by 1-1/2 in. Prior to bend testing 0.0025 in. of stock was removed from each surface by electro-polishing. Density measurements were made by the water-displacement method. In addition, a porosimeter was used to determine the amount of interconnected porosity for representative samples. Strength and ductility were determined from recorded values in transverse bending using a cross head speed of 0.020 in. per min. The load was applied at the midpoint of a 1-in. span. The deflection data reported herein refer only to the plastic portion of the total deflection. RESULTS AND DISCUSSION The as-sprayed samples had a density corresponding to 83 pct (l pct) of the theoretical density of tungsten. Fig. 1 shows a representative as-sprayed tungsten structure.

Jan 1, 1964

By D. L. Everhart

The search for new deposits raises two important questions: Where did the metallic ions that formed the orebodies come from? What processes and geologic factors were involved in ore replacement? A review of the wide geological variety of recent uranium discoveries tells how these questions are being answered. SOONER or later intelligent exploration for uranium leads to these questions: Where did the metallic ions that formed the orebodies come from? What processes and geologic factors were involved in ore replacement? These matters, of course, make a big difference in how best to look for orebodies. Before these questions are discussed it might be well to point out other factors bearing on the subject. The whole business of uranium exploration is only a little over ten years old, participation by the public is only about six years old, and real interest and activity by more than a few large mining companies has arisen only in the past two or three years. Throughout this short period, uranium exploration has been affected by the unique influences of necessary security measures and by division of the overall job into individual projects by a large number of specialists in diverse fields. This has meant that a normal interchange of information on the nature of uranium deposits has really only just begun. Compared to the vast amount of published studies on iron, copper, lead, zinc, and gold deposits over the past 50 to 75 years, current knowledge of uranium deposits is in its infancy and much of the pertinent information is still scattered about in a number of unpublished sources. The volume of reports on all phases of uranium exploration is now beginning to mount at a remarkable rate, and geologists with widely varying specialized backgrounds in uranium geology are engaging in spirited debates over the origin of uranium and the relative importance of geologic controls of various deposits. One of the most interesting features of known uranium deposits of the world is the wide variation, see Table I, in character and geologic environment. It should be noted that many types became prominent during 1953. The davidite-bearing veins of Radium Hill, South Australia, are almost unique, although the same mineral occurs in a different kind of deposit in Mozambique. Recent studies indicate that brannerite disseminated in the granite near Cracker&apos;s Well, South Australia, may soon constitute uranium ore. Basalt has been added to the list of favorable host rocks in the Northern Territory of Australia. Basalt is also the host of the pitchblende veins of the Martin Lake deposit, Beaverlodge district, Saskatchewan. The truly remarkable rich and extensive Steen deposit near Moab, Utah, is of the uraninite-vanadium oxide type. Secondary hydrous uranium arsenates and phosphates constitute the uranium minerals in the disseminated deposits of the Wind River Basin, Wyo., a new district discovered in the summer of 1953. Uranium minerals in shales adjacent to fractures were newly reported in New Mexico and several other parts of the world during the year. The well-known important uraninite dissemination in the Rand conglomerates of South Africa has a counterpart, as discovered in the summer of 1953, in the Mississagi quartzite and conglomerate of the Blind River district, Ontario. Gunnar deposit of the Lake Athabaska district, Saskatchewan, consists of uraninite in both granite and sedimentary gneiss beneath a granite cap, and large new orebody of the Eldorado Co. in the same general area follows a preferred stratigraphic horizon in schists. Uranium is, generally speaking, a very soluble and ubiquitous element. It occurs in at least two valency states and for this reason is not easily tied down in natural solutions. As Gruner&apos; has pointed out, it is probable that uranium starts in the hexava-lent state in nearly all solutions instrumental in its transfer. It is believed that under oxidizing conditions the uranium moves in solution as the uranyl ion, UO. In solutions ranging in pH from 1 to 5, the uranyl ion is most commonly in association with

Jan 1, 1955

By E. E. Thurlow

The Geology Div. of Northern Pacific Railway Co. has adapted to its exploration efforts field procedures for geochemical sampling and semi-quantitative analysis which have been developed through research by the U. S. Geological Survey. The sampling is done in conjunction with reconnaissance geologic mapping on aerial photographs or during field checking of maps which have been prepared largely by photo-geologic interpretation. Stream sediment or soil samples are taken and readily soluble combined heavy metals are extracted with ammonium citrate followed by colorimetric titration with dithizone at the sample site. The effectiveness of this approach has been demonstrated both in positive and negative results, thereby assisting in the elimination of large areas of land from further immediate attention and in providing targets for followup exploration. An occa sional sample is submitted for spectrographic analysis as a check on the possible presence of other elements of economic significance. Field laboratory procedures are also being implemented for determining molybdenum, mercury, and other metals which may be valuable in themselves or useful as pathfinder elements in outlining mineralized areas. A lead-zinc occurrence in Oregon and a copper deposit in Montana were readily detected and outlined by stream sediment and soil sampling and a heavy metal anomaly that lacks obvious interpretation has been found in northwestern Montana. Detailed mapping and additional sampling are followed by other exploration techniques if warranted. Northern Pacific&apos;s program of reconnaissance mineral evaluation of company-owned lands and adjoining areas was outlined in a paper presented at the American Mining Congress meeting in Las Vegas four years ago. That report included policies and procedures with respect to mineral development on Railway Co. lands and may be referred to for information on these matters.1 In a sense this paper is a progress report on the use of geochemical prospecting in Northern Pacific&apos;s continuing mineral evaluation program. At this time there are positive results but as yet there is no real success story in the form of a minable ore body. GEOCHEMICAL PROSPECTING PROCEDURES The decision to use geochemistry as a reconnaissance exploration tool must be followed by research into sampling and analytical methods and into the interpretation of results. Various analytical methods were tried and evaluated by the Geology Div., including hot and cold acid extraction with and without fusion of the sample, panning and magnetic separation followed by dithizone testing of the magnetite, and cold aqueous extraction of metallic ions followed by indicator tests. Samples were first sent to the laboratory for analysis; later field laboratories were established and now virtually all testing is done at the sample site. It was concluded that, where applicable, the quickest dependable methods for reconnaissance use are the dithizone field tests for readily extractable heavy metals. This involves the simultaneous treatment of a sample, usually of soil or stream sediment, with two immiscible liquids; one a cold aqueous extractant (ammonium citrate) and the other a solution of dithizone in toluene or xylene.2 Dithizone is a colorimetric indicator that reacts quantitatively with copper, lead, zinc, and several other metals to form colored complexes in organic solvents. Results may be expressed in ml of 0.001 pct dithizone that are required to reach the blue end point, or calibration of the test results can be carried out with standard solutions of zinc; conversion factors would then be expressed in ppm, zinc equivalent. Calibration of dithizone solution with zinc standards indicates that 1 ml of 0.001 pct dithizone is equivalent to approximately 0.25 ppm of zinc. An authoritative report on dithizone field tests authored by H. E. Hawkes in the June-July 1963 issue of Economic Geology* states "The appeal of these techniques has been the simplicity and speed of the determinations as compared with more tedious laboratory determinations of trace metals in weathered rocks, soils, or plant materials. This obvious appeal, however, has often been more than matched by misuse of the method in such a manner that the results are

Jan 1, 1964

By H. Kurushima, S. Tsunoda

An investigation of the hydrometallurgy of Cu-Zn concentrates by The Dowa Mining Co. of Japan is described and a detailed flowsheet of the Kosaka hydro-metallurgical plant is given. Sufficient operating experience has shown that the Dorrco FluoSolids system has proven successful for recovery of both zinc and copper by roasting in a fluidized bed. At present, 2400 metric tons of concentrates per month are being treated and recoveries of 93 pct Cu and 65 pct Zn are being effected. A SURVEY of the Japanese chemical industry in 1949 revealed, among other things, that sulphur-bearing blast furnace gas from the Kosaka smelter of The Dowa Mining Co. Ltd., Kosaka, Japan, was being exhausted to the atmosphere as waste. In addition, it was costing that company an average of ten million yen ($28,000) annually for damages to the surrounding property caused by the sulphur dioxide in the gas. It was recommended by this survey that the gas be utilized for the production of sulphuric acid by the contact process. Mr. Kurushima visited the United States in May 1950 to investigate the engineering, construction, and operation of a contact acid plant. Any acid produced at Kosaka would necessarily have to be 98 pct H,SO, to prevent corrosion in railroad tank cars transporting it to the point of use. However, the production of 98 pct acid requires constant volume and SO, content of the gas. As the converter gas at Kosaka fluctuates in both volume and quality, it was decided to evaluate the smelting process with relation to other methods of recovery. This evaluation revealed a relatively new type of roaster, the Dorrco FluoSolids reactor, which was reported to be capable of roasting the copper sulphide concentrate in an excess of air with the production of an SO1 gas strong enough for acid production and a water-soluble copper sulphate calcine. The copper sulphate then could be leached from the roasted ore and electrolytic copper recovered from the leach solution in much the same manner as practiced by the Chile Exploration CO. for treating naturally occuring copper sulphate ores. Use of a reactor of this type would eliminate the need for a blast furnace and converter and, in addition, would effect savings in labor and fuel. The Kosaka ore is a microscopically fine mixture of copper, zinc, and lead sulphides. The lead and a small amount of the barite present can be separated by flotation, but any separation of copper and zinc proved extremely difficult. In blast furnace operation at Kosaka, zinc had been slagged off until a stockpile of about 12,000,000 tons containing 5 pct Zn had been accumulated. Mr. Kurushima felt that if any of the zinc in the concentrate was sulphat-ized and leached with the copper, it also could be recovered electrolytically. The Dorr Co., sponsors of fluidization technique in the metallurgical field, suggested that sulphate roasting be tested out on a laboratory scale and that, if successful, a commercial Dorrco FluoSolids system be constructed. They indicated that the results from such laboratory tests could be transposed to a commercial scale without pilot planting the roasting operation. It was therefore decided to send samples of flotation concentrate to the West-port Mill, laboratories of The Dorr Co., for testing. The objective of Mr. Kurushima&apos;s visit to the United States thus had changed from investigation of sulphuric acid plants to a fundamental examination of the hydrometallurgy of copper and zinc. Testing Program In February 1951, Mr. Tsunoda went to the United States to witness the application of the FluoSolids system to sulphate roasting at The Dorr

Jan 1, 1956

By J. S. Brown, A. G. Guy

With the exception of the work of Tammann and Hartmann,1 no published information has been found on the structural changes produced in eutectic structures as the result of heating following plastic deformation. In part this lack of information may be due to the fact that many eutectic structures contain an intermetallic compound as a prominent phase, and as a consequence have been considered to be unworkable. For example, Tammann and Hartmann were able to obtain useful data only on those alloys that they could greatly reduce in thickness by cold rolling. This restriction placed on the investigation of alloys containing intermetallic compounds has been largely removed by the work of Savitskii2 which showed that large deformations of such alloys can be produced by relatively slow compression at temperatures near the melting range. It was possible, therefore, to carry out the present work on a range of binary eutectics including one composed of two intermetallic compounds. The essential results obtained on the alloy systems studied are illustrated by the Pb-Mg eutectic containing 33.2 pct Mg, Fig 1. The cast structure, Fig la, was obtained by melting together magnesium of 99.8 pct purity and chemically pure test lead, casting into a heated, small steel mold, and furnace cooling in the mold from about the eutectic temperature. The fairly coarse eutectic structure thus obtained was too brittle to work at room temperature without cracking. Fig 16 shows the worked structure obtained by compressing a 1/2-in. cube 70 pct in about 15 sec at 550°F and then water quenching. The pronounced changes in the distribution of the two phases produced by heating the worked alloy at 850°F for 1 hr are shown in Fig lc. Recrystallization of both phases appears to have taken place, and the mechanical properties of the cast alloy must have been significantly changed by the working and heat treatment. Similar results were obtained with the Mg-59.5 pet Bi, Mg-36.4 pet Sn, Mg-65.4 pet Cu, and Bi-40 pet Cd eutectics, only the last of which could be worked at room temperature. Tammann and Hartmann reported a thickening and shortening of the needles of the eutectics which they heated about 10°C below the melting range for 1 hr after drastic cold rolling. They found the following eutectics, given the indicated amounts of reduc- tion, to have a granular structure after heat treatment: Sn-9 pet Zn (98 pet); Cd-82.5 pet Pb (60 pet); and Bi-43.5 pet Pb (90 pet). On the other hand the alloy Al-11.7 pet Si (60 pet) showed no change after heating. Tammann and Hartmann observed a distinct shrinking of the needles in unworked eutectics subjected to heat-treatment. In the present work inappreciable change in the eutectic structure was found on heating undeformed alloys. In summary, it appears that eutectic structures can be recrystallized into a "spheroidized" condition by heating near the eutectic temperature after severe deformation. If the eutectic contains one or more brittle phases the necessary deformation can be accomplished by pressing at high temperatures. It is reasonable to expect that this tendency towards equiaxed grains from the plate- or needle-like eutectic structure should be general since the energy relations and mode of growth in recrystallization are so different from those that hold for eutectic crystallization. References 1. G. Tammann and H. Hartmann: Ztsch. Melallkunde (1937) 29, 141-144. 2. E. M. Savitskii: Doklady Akad. Nauk S.S.S.R. (1940) 62, 349-351. Abstr. in Melal Prog. (July, 1949) 56, 126, 128.

Jan 1, 1950

T.P. 1958 D. H. DAVIS.*-Mr. Carris has ably pre¬sented the problems of coal preparation, particularly those brought about as the result of increased mechanical loading. Many mines are now crushing the run-of¬-mine raw coal through 12 or 15 in. immediately after it is dumped from the mine car and before it is handled by conveyors. At certain mines the removal of large slate mechanically has been solved by the installation of scalping screens consisting of bars or rails set at spacing of 12 to 15 in. on the top deck of the main raw-coal sizing screen. At the plants where these are in use, the plus 12 or I5-in. raw material contains 60 per cent or more free rock or slate, so that it is easier to pick coal than to pick rock. After the screening at 12 or 15 in. is accomplished, the oversize material is diverted to one side of the shaker, where a picker allows the refuse to pass off the shaker into a chute and guides the coal back onto the shaker. After the large rock has been removed, it is then advisable to reduce the size of rock by crushing before putting it onto a conveyor. A great saving in picking labor has been made by the use of such scalping screens, which in addition has maintained the plant capacity when handling a dirtier feed. The great increase in percentage of coal under 1/4 or 3/8 in., coupled with a greatly increased percentage of free impurities in this size, is the most serious problem that has been brought about by mechaniced loading. Many plants that formerly prepared good quality 1/4-in. to o or 3/8-in. to 0 slack by air¬cleaning are faced with installing facilities for wet-cleaning mechanical and heat-drying and water clarification. The change to wet prepa¬ration of fines usually affects the marketing problems for many coal companies. There will also be problems involving wastage of fine solids and stream pollution. Much work will be necessary for improvements in present practice. Pneumatic and electrostatic methods for cleaning fine coal should receive consider¬able attention in an attempt to avoid wet¬cleaning of fines. The preparation supervisor and the plant personnel should not be satisfied merely to run the cleaning-plant machinery and assume that the job will be done for them. Coal is a heterogeneous substance and in many instances is constantly changing. This is more true when full-seam methods are in use. Only persons trained to observe closely and make the necessary changes in plant operation will be able to solve the many problems that will be imposed on the preparation plants. The plants will require skillful and observant operating men. With full-seam mining methods, seams of roof coal will often be mined. Under the former mining systems these strata were not mined and frequently they contain a high per¬centage of bony and banded partings. The mining of this coal will greatly alter the washability and specific gravity characteristics of the feed to the plant. Often the percentage of 1.40 to 1.60 sp. gr. increased from 3.5 to 7.5 per cent, or nearly a 1.0 per cent increase in the ash content of the 1.60 sp. gr. float coal. Thus the cleaning problem is much more difficult, and it is unlikely the same ash content of cleaned coal can be produced as before without a decrease in recovery or the produc¬tion of a "middlings" product. Mr. Carris had this in mind when he said "The quality of the

Jan 1, 1946

By Klaus Detert, Joseph Ziebs

The progress of primary recrystallization has been studied in alloys of nickel with 0.01, 0.1, and 1.0 at. pct Ta. It can be shown that in one particular alloy containing 0.1 Ta and 0.02 02 a large grain structure (0.5 mm diameter) could he developed by primary recrystallization in thin sheetswhich were cold-worked to 97.5 pct reduction in thickness. Electron transmission microscopy demmstrates that this phenonmena was linked to the occurrence of fine precipitates at subboundaries. A discussion of how fine precipitates can exert under certain circumstances a rather distinct retarding effect on nucleation rate is included. IN a former investigation, the recrystallization and texture formation in a series of binary nickel alloys including pure nickel were studied.&apos; Nickel alloys with some tantalum added displayed peculiarities during primary recrystallization which have been studied in more detail by the present investigation. The alloys were prepared by powder-metallurgy techniques similar to the previous investigations.&apos; Pure metal powders were thoroughly mixed to obtain alloys with 0.01, 0.1, and 1.0 at. pct Ta, referred to as alloy A, B, or C, respectively. The metallic impurities were kept below 0.005 at. pct except iron and cobalt with slightly higher values, by using highly purified nickel and tantalum powders.&apos; The mixtures were pressed into bars and sintered at a temperature of 1300°C. The sintering atmosphere was either high vacuum, dry hydrogen, or wet hydrogen. The sintered rectangular bars were rolled 60 pct to a thickness of 3 mm, then annealed under dry hydrogen at 1000°C and again cold-rolled to about 97.5 pct reduction of thickness. After this heavy deformation, the sheet thickness was 0.07 5 mm. In order to study primary recrystallization which occurred in measurable times between 400" and 600°C, samples of the rolled sheets were annealed in a salt bath at various temperatures for various times in order to study the progress of recrystallization by hardness measurements and microscopic examination. For optical observation, the samples were polished and etched in a solution of 65 cu cm HNO3, and 18 cu cm acetic acid in 20 to 100 cu cm H2O, depending of the particular sample and annealing treatment. For transmission electron microscopic observations, thin foils were prepared by the combined window and Bollmann techniques.273 The electrolyte consisted of 23 pct perchloric acid and 77 pct acetic acid held at 15°C. Polishing was performed at a current density of 0.4 amp per sq cm. The examination of the thin films was accomplished by a Siemens Elmiscope-type electron microscope operating with an accelerating voltage of 100 kv. RESULTS The progress of primary recrystallization was very accurately followed in these alloys in order to establish the time when recrystallization started and ended during an isothermal anneal. Table I gives some of the data obtained by these studies. The time for beginning is a mean value, where somewhat less than 5 pct of the matrix has recrys-tallized. The end of recrystallization is the time when at least 95 pct of the matrix has recrystal-lized. Listed are three different B alloys, with 0.1 Ta distinguished by different sintering atmospheres which influence the rate of primary recrystallization. By the above method, the state of the grain structure when primary recrystallization was completed, but grain coarsening had not started, could be clearly defined. The average grain diameter of the recrystallized matrix is also given in Table I. The grain size did not depend on the temperature of the isothermal anneal. With one exception the grain size of the primary recrystallized matrix was found to be rather fine

Jan 1, 1965

By Whitman E. Brown, Louis J. Erck

L. A. ROE*—This paper is one of great value to the iron ore industry. The Humphreys spiral is a relatively new tool and gives promise of being quite useful in solving certain problems of iron ore beneficiation. Spirals have been tested on a martite ore at the Benson mine of Jones and Laughlin Steel Corp. in northern New York State. Our New York ore is considerably different, physically and mineralogically, than the one mentioned in this paper, and contains only 25 pct iron. This ore can be processed on spirals to give a concentrate containing 62 pct iron with an 85 pct recovery. On our particular ore we found operating difficulties when the spiral feed was coarser than 14 mesh. These were chiefly due to excessive "build-up" of locked middlings in the spiral circuit. In extreme cases these middling particles would accumulate to such an extent that the plant had to be shut down and the spiral surge tanks cleaned out. It is interesting to note that there exists a close relationship between the results of tabling a given iron ore and concentration of this same ore on Humphreys spirals. The size range of the ore must, of course, be within those limits acceptable to spiral concentration. Comparative tests on several of our mar-tite ores showed tabling results to be the same as spiral results. The authors make no mention of the use of a tailing stream splitter (now available from the spiral manufacturer) which is a useful tool in studying iron losses in the tailings stream. 011 our particular martite ore we found a considerable accumulation of fine-sized iron ore particles in the outside portion of the tailings stream. This fraction may be amenable to further treatment. E. H. ROSE*—The authors have concluded an interesting piece of work and this paper is an excellent factual account of a rapid and somewhat unusual transi-;ion in practice in the plant described. Perhaps it was modesty on their part which caused them so casually to limit to one sentence the fact that "several other methods of concentration on the fine ores representative of the Hill Trumbull group . . . failed to produce consistently an acceptable grade and recovery of finished product." The fact is that they were confronted by a difficult mineral-dressing problem and they are to be congratulated on their courage and persistence in staying with it until a satisfactory solution was evolved. A visitor to the plant might have been mildly astonished, as I was, to see one type of concentrator handling that part of the load early in the 1947 season, its experimental replacement by another a little later, and then in 1948 to see that both types had simply disappeared and their place taken by the spirals which were operating as placidly as though they had been there all the time. In working out economic methods of beneficiating Alabama red ore, most of which development is still ahead of us, it is likely that we also will pass through a period of successive disappointments, for we too have a problem where it is next to impossible either to "guess &apos;end right in the first place," or, because full-scale operating cost is such an important factor, to lay the ultimate answer on the line in advance by means of laboratory experimentation. Iron ore being what it is instead of what it used to be, it is encouraging to have the example the authors have given us today that a tough nut that will not crack on the first blow or the second is apt to do so on the third or fourth.

Jan 1, 1950

By Cloyd M. Smith

B. F. TiLLson*— The manifold difficulties of accurate anemometry in irregular sections of mine passageways, the irregular distributions of velocities in cross sections of the same, and the disturbing influence of the observer upon the air flow, all indicate an undesirable inaccuracy of results obtainable by any standardized method of traversing the section by an anemometer. It seems obvious that another, and simpler, method should be used to determine the volume of air flow in mine passages, namely: 1. At appropriate locations cement or calked framework rings should be installed permanently to equalize the irregularities of sectional contour and provide a place and means of attachment for a temporary cloth brattice which bears a rigid orifice. 2. The measurement of the velocity of air flow through the orifice may then be by anemometer or, preferably, by Pitot tube measurements of the differential pressures on both sides of the orifice in accordance with the standard practices available in engineering 1iterature. † The constants may be determined for various measuring positions in relation to the resulting "vena contracta." 3. The position of the person who makes the measurements is behind the brattice out of the air stream. The Pitot tube does not offer as disturbing an obstruction as the anemometer. A recording gauge may be employed to integrate fluctuations in air flow through that portion of the mine. No traverses are required because the reading may be at a single central point. An anemometer can be used with an orifice flow. The orifice will increase the air velocity at the measuring point, with correspondingly more accurate measurements where the normal air velocity through the passageway is low. Portable brattices might be devised with the cushioning rims which would seal against irregular rock surfaces where permanent rings were not available or feasible. The development by the Ventilation Committee of standard procedures and devices for the orifice measurement of the flow of mine ventilating air might be a desirable project for this coming year. C. M. Smith (author&apos;s reply)—Thank you for your discussion of my paper on underground anemometry. Your suggested method of measuring underground air flow is a novel one which might be applicable in some situations. It should be tested along with other suggested methods in any investigation of this subject. G. E. McElroy*—In spite of the adverse publicity that vane-anemometer methods of air measurement have had in the past and that contributed by the present paper, I endorse Mr. Erickovic&apos;s statement that anemometer traversing "has proved to be widely applicable, expeditious and simple" and add that available methods are accurate enough for the purposes for which they may be used. The fact that the great majority of minor mine officials assess relative changes in rates of air flow by comparison of crude vane-anemometer measurements, known to average 20 to 30 pct high, has no important bearing on this subject, because state inspection standards were based originally on such methods of air measurement. Federal inspection standards are based on actual rates of flow as determined by traversing, and interest in traversing methods is rapidly increasing. In considering traversing methods, three aspects are of major importance: (1) the absolute accuracy of calibrations; (2) the degree of interference with normal flow conditions introduced by traversing methods designed for accurate measurement by shaft-mounted instruments; and (3) the proper "method" factor to use for approximate measurements by hand-held instruments. With respect to absolute accuracy of calibrations, we have always placed reliance on calibrations made by the National Bureau of Standards, with which manufacturers&apos; calibrations have usually agreed very closely. It is therefore particularly disturbing to find7 that calibrations made previous to June 1947 are presumably about 5 pct in error because of excessive registry caused by the thin flat plates on which anemometers were mounted for calibration. Velocities corrected for calibration have therefore averaged about 5 pct low in all probability. In this connection, it is interesting to note that an anemometer calibrated against Pitot-tube measurement by a single-point method in the Bureau of Mines experimental coal nine in 1923 indicated this same difference of about 5 pct and that the same instrument calibrated by a traversing method in a metal mine some months later indicated a difference in the same direction of about 4 pct. These results are reported by the Bureau of Mines.8 Regarding the degree of interference, or changes in velocity distribution, caused by the position of the observer&apos;s body in traversing operations, misconceptions seem to be especially prevalent, resulting in increasing advocacy of methods, such as the "clear section" method outlined in this paper, that cause just the type of interferences that they are designed to avoid. The degree of interference for any method may be gauged easily by a few experiments with a velocity-pressure gauge connected to a Pitot tube or with an indicating velocity meter such as the Velometer. In an experiment cited by McElroy and Richardson,# a decrease of 5 pct was noted at ten widths upstream from a 6-in. plank, whereas an observer&apos;s body at about the maximum practical distance of 6 ft downstream from the instrument is only about four widths away. In the Bureau of Standards paper previously mentioned, it is recommended that supports used in calibrations be at least 16 widths downstream. In practice, therefore, a downstream position of the observer is ruled out as far as accurate measurement is concerned. Operation of the anemometer by rigid shaft support from a point outside the section is seldom practicable; however, accurate results can be obtained, with the anemometer rigidly attached to a short shaft and held at arm&apos;s length, by an observer advancing across the traversed section while he faces the opposite wall and stands sideways to the current, provided that he keeps the instrument at least 3 ft away from his body at all times and traverses the entire section with it. If the traverse can be started with the observer in a side recess, the entire section can be covered in one operation. Normally, it would be covered in two half-sections. The presence of the observer&apos;s body does not, as is commonly supposed, increase the average velocity throughout the remaining part of the section. Rather, the velocities 1 to 2 ft on either side of his body are increased, but the distribution of velocities throughout the rest of the cross section remains normal, and a traverse made as stated gives a true average velocity for normal-flow conditions. Regarding the proper "method" factor for accounting for interference in the approximate methods of traversing with hand-held instruments, here again confusion prevails, for which the writer must assume some of the blame. Comparison of consecutive traverses made by shaft-held and hand-held 4-in. anemometers in field work after the tests reported by McElroy and Richardson&apos; gave method factors

Jan 1, 1950

By George A. Roberts

The development of an alloy system, high-speed steel, is used as an example of the progress of physical metallurgy. Tracing the history of men and their thoughts as they studied and invented and modified these materials, the story of high-speed steel since the 1890&apos;s is seen to be a long, slow, but steady progression of achievements. Today&apos;s multiplicity of high-speed steels are the result. Data are presented on quantitative metallography of carbides in high-speed steel with high vanadium content using the QTM instrument. Grindability as well as mechanical properties are related to the content of excess MC and M6C carbides in a series of high-speed steels and the newer matrix steels. These emphasize the present state of knowledge and show the current stages of thought that may affect the development in succeeding years. It is a great thrill for me, an ex-research metallurgist and ex-practicing metallurgical engineer, to speak to an audience currently engaged in both pursuits on the occasion of the 43rd Howe Memorial Lecture before the Iron and Steel Division of the AIME. I shall not review Henry Marion Howe&apos;s distinguished career, so adequately reviewed in Maxwell Gensamer&apos;s contribution in the 1965 AIME History of Metallurgy, except to point out that, while leading the life of an intellectual, he worked as a practicing research metallurgist and a practicing metallurgical engineer for significant periods of time and contributed greatly in both areas. For those of you who believe, as I do, that in the intellectual activity of metallurgy we are blessed with an intimate mixture of science and engineering (see Mehl&apos;s 1960 Howe Lecture), we might recall that Howe, while pursuing a life of writing and teaching in later years, served as the first Chairman of the Division of Engineering of the National Academy of Sciences. That metallurgists were called upon then to lead an engineering recognition movement is perhaps related to the strong part played by the AIME and its members in the recent establishment of a National Academy of Engineering and to the fact that a metallurgist is its head, 47 years after Howe served. I stress these engineering aspects for I wish to talk about a metallurgical engineering subject today. Alloy systems, physical metallurgy, and steel blended with an historical perspective and a report on new techniques to improve the old will, I trust, be of sufficient interest to bring these lectures back to the physical-metallurgy banner from which they have departed for 4 years. Those process metallurgists, open-hearth fiends, and physical chemists among you will just have to be patient. The development of an alloy system is the engineering application of scientific thought and fact. There are many interesting alloy systems, developed to a high degree of technology and sophistication over the past 40 to 70 years. These systems are bound together and related by a similar set of characteristics. For example, stainless steels are a system in which the members are related by a high chromium content which gives a corrosion-resistant characteristic. A subfamily in this system would be austenitic steels

Jan 1, 1967

By W. Vickers

Single-point rotating cantilever fatigue tests have been carried out at 550" to 650°C on beryllium produced by a variety of fabrication routes. All the specimens gave similar plots of stress against number of cycles to failure but failure occurred at a lower stress range in the hot-pressed material than in the extruded material. A discontinuity or "kink" appears to exist in the curves and this is considered. A true endurance limit was not evident up to 10 cycles. When Brush hot-pressed warm-extruded beryllium was tested at 600oC a relationship where Nf = number of cycles to failure, ?ep = plastic strain range, and c = constant, was shown to be applicable for values of ?ep > 6.3 x 10-4. Further for this moterial and temperature and for frequencies between 150 and 4500 cycles per min, the variation of number of cycles to failure with frequency obeyed the expression N = Af0.44 where N =number of cycles to failure, f = frequency, and A = constant. Examination of the fracture surfaces indicated that they were generally intergranular and in all cases the higher the stress the more irregular was the fracture. Microexamination has shown that grain boundary cavities and fine intergranular cracks were associated with the fractures. REVERSING or cyclic stresses set up in fuel elements can lead to failure by fatigue. Fatigue stresses may be developed by instability of the fuel element in the coolant flow leading to rattling against the channel wall or fin vibration. Thermal cycling also sets up reversing stresses due to differential expansion of fuel and can. Fatigue resistance is of some importance therefore in the evaluation of canning materials. At the time the work described in this paper was initiated, beryllium was being considered for the can and endcaps of an advanced gas-cooled reactor fuel element. With this in mind, beryllium obtained from different manufacturing routes was tested on single-point rotating cantilever fatigue machines at temperatures the same as those envisaged in the reactor to obtain appropriate fatigue data. The results obtained indicated a discontinuity in the S-N curves coinciding with the yield stress in the specimens. Although in some cases the data is insufficient to warrant a detailed quantitative analysis, a qualitative analysis of this effect was thought to be justified. 1) EXPERIMENTAL DETAILS The materials used are given in Table I together with the production route and available analyses. The specimen shape is shown in Fig. 1. The fatigue specimens were machined slightly oversize, after which they were given a stress-relieving anneal of 1 hr at &apos;750° C in vacuum. This was followed by an etch in sulfuric-phosphoric-chromic acid mixture down to the finished dimensions given in Fig. 1. Etching served to remove the interference colored oxide film formed on the surface during annealing and very small recrystallized surface grains too. The specimen was mounted in the grips of a cantilever machine and rotated inside a furnace controlled at the testing temperature. The specimen was loaded in increments as the speed was increased until the required load was applied at 5000 cycles per min. A revolution counter was used to record the total number of cycles.

Jan 1, 1964

By G. Meyrick, H. W. Paxton

Observations on the tensile deformation of single crystals of austenitic stainless steels as a function of composition, orientation, and temperature are described and compared with relevant data for other alloys. Crystals free from second phases show sharp yield points followed by Lüders&apos; extensions of up to 20 pct. The critical resolved shear stress is strongly temperature-dependent increasing fourfold between 423O and 77°K. A temperature-independent low rate of hardening follows the Luders&apos; extension and is frequently associated with overshoot. Unlike pure metals where Proficse cross slip usually occurs at the end of linear hardening, this stage is terminated either by cross slip or by slip on the conjugate system, the particular node apparently depending upon initial orientation and composition. The presence of 6 ferrite or martensite has a profound effect upon the magnitude of the yield stress and the shape of the stress-strain curve. In experiments on transgranular-stress corrosion cracking of austenitic stainless steels in boiling magnesium chloride, several workers1&apos;2 have shown that increasing amounts of nickel tend to reduce the probability of specimen failure. Reed and paxton3 have observed in single crystals that the macroscopic crack plane changes as the nickel content is increased. For 18 pct Cr-8 pct Ni, the crack plane is sensibly perpendicular to the applied tensile stress; for 20 pct Cr-20 pct Ni the crack plane is (100). The average crack-propagation speed is much lower in the 20 pct Ni crystals. Furthermore, the possible importance of stack-ing-fault energy in nucleation and growth of cracks has been suggested by a number of workers. While the general effect of variations in stack ing-fault energy appears to be quite well-correlated with observed variations in cracking characteristics, each of the theories assigns rather different detailed reasons for these effects. Because the stack ing-fault energy of austenitic steels is believed to be increased with increasing nickel content, and because some theories of trans-granular cracking postulate a mechanical stage in the crack propagation (rather than relying entirely on electrochemical solution), it appeared to be of some interest to investigate the mechanical properties of a series of different compositions of aus-tenite single crystals. These experiments were considered of intrinsic value in view of the relative scarcity of such data on fcc alloys. This paper gives the results of some experiments carried out with this aim in mind, and suggests various &apos;other experiments which may be helpful in future studies. The experiments are also of interest in view of the recent interest in obtaining higher-strength steels by control of the imperfection content of austenite; although the compositions are not directly comparable, the results are still probably valuable. Comparisons with experiments on other fcc alloy crystals are made where possible to see how well the general pattern of behavior is understood. EXPERIMENTAL PROCEDURE The alloys used in this investigation were vacuum-melted heats of nominally 20 pet Cr-20 pet Ni-60 pet Fe, 20pctCr-16 pct Ni-64 pct Fe, and 20 pctCr-12 pet Ni-68 pet Fe.* Analyses of the material are

Jan 1, 1964

By A. Kelly, S. Sato

Tensile tests have been performed on aluminum single crystals of 99.99 pct purity at 196°K. The resolved shear stress when the stress-strain curve becomes concave to the strain axis depends on orientation, being always higher for crystals with an initial orientation close to the sides of the unit triangle. Observations have been made, with the optical microscope, of the appearance of slip lines on polished surfaces of the crystals. Particular attention has been paid to the first appearance of cross-slip. It is confirmed that marked cross-slip is first seen when the stress-strain curve becomes concave to the strain axis. Measurements are reported of the lengths of the slip lines observed on top and side faces of the crystals at various stages of the deformation. The lengths of the slip lines vary inversely as the flow stress for all crystals, independent of crystal orientation. From measurements of the lengths and separations of the slip traces it is possible to estimate the number of dislocations which are annihilated at each cross-slip site. It is concluded that the annihilation of screw dislocations of opposite sign is the most important cross-slip process occurring. FRIEDEL1 recently pointed out that the stress-strain curve of many pure metals of face-centered-cubic structure can be considered as composed of three stages. Plastic flow commences with a region showing a small rate of hardening which is approximately linear. This has been called "easy glide*. It is followed by a region of more rapid hardening in which the slope of the curve is again approximately constant and this, in turn, is superseded by a final part of the curve which is concave to the strain axis. Following Diehl2 we may designate these regions as stages I, II, and III respectively. The onset of stage 111 occurs at lower stresses at higher temperatures. The appearance of the slip lines formed during these various stages has been described by a number of workers?-5* The object of the present work was to make detailed observations of the lengths and separations of slip lines for a number of crystals of different orientations deformed at the same temperature and strain rate. Although much previous work has been published on the deformation of aluminum single crystals the importance of measurements of these quantities has only recently been realized—they are essential for experimental tests of recent theories of work hardening.&apos; 9 In aluminum, deformed at room temperature, stage 11 of the stress-strain curve is very weakly marked, as the stress for the onset of stage 111 is attained soon after the end of easy glide. In the present experiments it was decided to use a temperature lower than room temperature so that stage II of the curve was better developed. However, at temperatures as low as 90°K slip lines are not measured easily with the optical microscope.5 For this reason 1960k was chosen as a suitable temperature. Even at 1960k however, stage III of the curve commences at glide strains of 6 to 10 pct and hence

Jan 1, 1960

By C. D. Stahl, S. M. Farouq Ali, W. E. Culham

One- and two-dimensional mathematical models have been developed that simulate transient, two-phase flow of hydrocarbon mixtures in porous media in a manner that accounts for interphase mass transfer. Numerical simulations of one-dimensional depletion-drive experiments using a two-component hydrucarbon fluid were used to establish the validity of the mathematical models. In addition, the experimental and numerical data were used to demonstrate that production rate had a relatively insignificant effect on the recovery of individual hydrocarbon components from the experimental system, and that attainment of equilibrium between phases is possible for a wide range of liquid and vapor velocities in reservoirs containing light hydrocarbon fluids. Results of some two-dimensional numerical simulations are also presented. INTRODUCTION This study was undertaken to develop a mathematical model that would simulate transient, two-phase flow of hydrocarbon mixtures in porous media under conditions that result in interphase mass transfer and to test the validity of the assumptions used to set up the model. In addition, the study was designed to determine if production rate influences the recovery of individual hydrocarbon components from reservoirs producing by depletion drive. Two-phase flow in porous media, with interchange of components between the two phases, is important in many petroleum recovery processes. Studiesl-5 conducted within the last 3 years have outlined methods of solving multiphase flow problems incorporating mass transfer. Some of these studies have also indicated the importance of accounting for mass transfer under various producing conditions. An earlier work6 first demonstrated the importance of combining relative permeability data with equilibrium ratios in compositional balance methods. The mathematical model presented in this paper is formulated so that a phase behavior package, as described in previous papers,5,17 is not required as an integral part of the routine employed to solve for the primary dependent variables. The finite difference formulation is designed so that all the primary variables can be solved for simultaneously. This is accomplished by utilizing one basic set of equations. These innovations, which are in contrast to other models2,3,5 but are similar in some respects to the approach used by Taylor,l render the total problem computationally simpler than any of the previously referenced formulations. The mathematical model was developed by combining Darcy&apos;s law with a continuity equation for each hydrocarbon component. The principal assumptions invoked in the formulation were (1) that capillary forces and diffusional effects are negligible, and (2) that thermodynamic equilibrium exists in the reservoir at all times. No assumption as to the type of vaporization process was made in formulating this model. Experimental data were required to complete this study. These were generated by conducting several depletion drive experiments. The experimental apparatus consisted of a sandstone core enclosed in a pressurized casing. The apparatus was designed in such a manner that the core could be charged with a liquid hydrocarbon mixture and depleted at different production rates. The experimental tests were designed to determine the effect of production rate on component recovery. In addition, direct comparison of experimental and mathematically predicted

Jan 1, 1970

By R. C. Hassinger, D. V. von Rosenberg

Transverse dispersion has received considerably less treatment in the literature than has longitudinal dispersion. Different methods for determining transverse dispersion coefficients have been used in different investigations, and the results obtained have not been consistent enough to permit accurate generalizations as to the effect of various physical parameters on the magnitude of these coefficients. A numerical solution to the differential equation describing transverse dispersion in the absence of longitudinal dispersion was obtained to enable one to calculate the dispersion coefficient from experimental results. The more general dispersion equation including longitudinal dispersion also was solved numerically to give quantitative limits of a dimensionless group within which the assumption of negligible longitudinal dispersion is justified. Possible experimental procedures were examined, and one utilizing a cylindrical packed column was chosen for the determination of transverse dispersion coefficients. Values of these coefficients were determined for a system of two miscible organic fluids of equal density and viscosity, for two sizes of packing material over a wide range of flow rates in the laminar regime. The dispersion coefficient was found to decrease, for a constant value of the product of packing size and interstitial velocity, as the size of the packing material particles increased. INTRODUCTION Longitudinal dispersion has received extensive treatment in the literature, and consequently is better understood than its orthogonal counterpart, transverse dispersion. Many mathematical models of dispersion processes assume that transverse dispersion is rapid enough to damp out any radial** concentration gradients and therefore may be neglected. Laboratory and production results, however, indicate that this is a poor assumption.l,2 Various experimental procedures for determining transverse dispersion coefficients have been used in previous investigations, but the results have generally been expressed by similar correlations. The transverse dispersion coefficients obtained, however, have often varied considerably for given values of the correlation parameters. We feel that further experimental determinations of transverse dispersion coefficients will help alleviate some of the inconsistencies in these empirical correlations. One assumption implicit in all previous investigations is that of negligible longitudinal dispersion in the experimental system. An attempt to justify this assumption often is made using intuitive reasoning, but it is apparent that this reasoning must break down as the condition of zero flow rate is approached. A mathematical examination of the equations describing the system yields physical limits outside of which the assumption of negligible longitudinal dispersion is invalid. BACKGROUND In a porous medium, the "effective molecular diffusivity" De is less than the molecular diffusivity D measured in the absence of a porous medium, due to the tortuous path which a diffusing molecule must travel. Various authors3-5 have reported values of the ratio De/D in the range of 0.6 to 0.7. When there is fluid flow within the porous medium, mass transfer occurs by convective dispersion as well as by molecular diffusion. These are separate phenomena and can be treated as such on a microscopic scale. However, the mathematical complexity is such that only extremely simple geometries could be considered, and the results hardly would be applicable to the complex geometries existent in actual porous media. A more

Jan 1, 1969

By M. E. de Morton

Recovery and early recrystallization of heavily deformed, 99.98 pct Cr was investigated by studying metallographic structure. X-ray line sharpening, electrical resistivity, plastic properties, internal friction, and shear modulus. Appreciable recovery of resistivity, internal friction, and shear modulus together with some hardening and relief of internal strains occurred before the visible growth of a textured substructure above 350°C (recrystallization in situ). The complex behavior of shear modulus, internal friction, and its strain amplitude dependence during annealing are discussed qualitatively in terms of the relative mobility of dislocations. BY plastically deforming fully recrystallized 99.98 pct Cr above the brittle to ductile transition temperature, at -350°C. as in wire drawing, chromium can be made very ductile at room temperature. However, this ductility is lost on annealing at high temperatures when recrystallization takes place.&apos; The present investigation was made to determine the general pattern of the changes in a number of physical and mechanical properties during recovery and recrystallization of heavily deformed chromium as part of an effort to elucidate the reasons for lack of ductility in the fully recrystallized condition. PREPARATION OF MATERIAL Wire specimens 0.027 in. in diam were prepared from arc-melted, electrolytic chromium by extruding, hot swaging and finally wire drawing at 300" to 350°C, i.e. above the brittle-to-ductile transition temperature. The total reduction in area of the wire was 98 pct and the last 3 pct of reduction was made at 100" to 150°C before cooling to room temperature. The impurity content of the material is shown in Table I. Internal friction and modulus measurements were made on a single specimen after annealing in situ at successively higher temperatures. For all other measurements, a fresh specimen was used for each temperature and annealing of these specimens was done in evacuated (0.001 mm Hg) and sealed silica tubes for 1 hr at the various temperatures up to 700°C. EXPERIMENTAL METHODS AND RESULTS The occurrence of a. transition in some physical properties of chromium at - 40°C2 imposed limitations on the temperature region where some of the measurements could be made. The reason for this transition in chromium is at present unknown but is probably associated with an antiferromagnetic state observed below - 40°C.* Heavy deformation produces an anomalous decrease in resistivity when measured at temperatures below -40°C4 though a normal increase is observed above this temperature. On the other hand internal friction in heavily deformed chromium5 over the temperature range 40" to 50°C is invariant with temperature. Above and below this range internal friction is strongly temperature dependent, increasing with increasing temperature. A temperature in this range was therefore convenient for both resistivity and internal friction measurements and for consistency the measurements of the mechanical properties were also made at about this temperature. No structural change has, however, been observed in careful X-ray measurements6 between -195" and 50°C, i.e. departure from cubic symmetry was not greater than 3:10,000; X-ray line sharpening measurements were therefore more conveniently made at room temperature.

Jan 1, 1962

By M. S. Burton, J. E. Ritter

The sessile-drop technique was employed to study the effect of atmosphere and alloy additions of titanium and chromium on the surface tension and contact angle of nickel on sapphire substrates at 1500oC. Shear tests were conducted on the solidified sessile drops. The liquid-gas surface tension of pure nickel on sapphire was found to be 1747 ergs per sq cm, with a contact angle of 109.6 deg. The surface tension and contact angle were not affected significantly by the four atmospheres, vacuum, impure argon, pure argon, and pure hydrogen. Small additions of titanium and chromium decreased the contact angle and for the same alloy content, contact angles were lower in pure argon than in pure hydrogen. On the basis of shear-test results , the most probable cause for adhesion in the Ni-Al2O system is the formation of NiO:Al2O3 spinel at the interface; in the titanium alloy-Al2O3 system adhesion is thought to be due to a mechanical interlocking effect; in the chromium alloy-Al2O3 system adhesion is believed to be the result of solid-solution formation involving Cr2O3 and Al2O3 at the interface. In the last few years there has been considerable interest in reinforcing metals with ceramic whiskers. It has been postulated that, by reinforcing nickel with sapphire whiskers, high-temperature strengths su- perior to those of the best current nickel alloys can be achieved.&apos; To fabricate a whisker-metal composite having optimum density and strength, understanding of wettability and adherence in the system is of prime importance. Although there has been some previous research in this a a need for further studies has been cited4-8 to understand better the effects of impurities, alloys additions, and atmosphere on the wetting and bonding of metals to metal oxides. The purpose of this research was to investigate the factors involved in the wetting and adherence of nickel/nickel alloys to sapphire (single-crystal a Al2O3). Sessile-drop experiments were conducted in vacuum, impure argon, pure argon, and pure hydrogen, to determine the effect of atmosphere on the contact angle of the metals on sapphire, and the liquid-gas surface tension of pure nickel. The solidified sessile drops were sheared from the sapphire substrate to measure the bond strength between the metal and ceramic. The alloy additions chosen were titanium and chromium since both enhance the wetting of nickel on sapphire.2, 3c Also, titanium is commonly used when brazing metal-to-ceramic seals to improve adherence. Since chromium forms an oxide that is completely soluble in sapphire, it was thought that the oxide could serve as a transition phase to promote bonding between the Ni-Cr alloy and sapphire. I) EXPERIMENTAL APPARATUS AND PROCEDURE The sessile-drop apparatus was a horizontal furnace, with an induction-heated, cylindrical molybdenum susceptor in a water-cooled Pyrex chamber. This apparatus was patterned after that of Williams and Nielsen.7 A flat Pyrex window at each end of the furnace allowed temperature measurements to be made at one

Jan 1, 1968

By D. Weinstein

Yieldilzg in annealed arc-cast molybdenunz in torsion was studied as a function of strain rate and tem-perature. The temperature dependence of the yield point for different strain rates was used to calculate a heat of activation for the yield point. The heat of activation was not a constant but was approximately a linear function of the stress at yield. It is proposed that the rate effect in yielding is determined in part by a site place-change of C (or other interstitial atom) in the metal. THE low-temperature embrittlement phenomenon in metals and alloys has been known to exist for a long time. Although a transition from ductile to brit-tle behavior has been observed in some close-packed hexagonal metals1 and a face-centered cubic alloy, the most common class of metals exhibiting this be-havior has a body-centered cubic lattice structure. For example, a ductile to brittle transition has been observed in iron,3 molybdenum,4 chromium,5 colum-bium,6 and tungsten.7 In the present investigation, molybdenum specimens were tested in torsion over a wide range of temperatures at three widely separated strain rates, and the temperature for onset of embrittlement was determined. Characteristic of body-centered cubic metals and closely associated with plastic deformation is the appearance of a sharp upper and lower yield point. Theoretical explanation of the yield point in iron and low-carbon steel is due to Cottrell,8 who attributes the phenomenon to the pinning of dislocations by the formation of impurity atmospheres around the dislocations. These atmospheres tend to lock the dislocations and make them more difficult to move. The stress required to move a dislocation and thereby cause plastic deformation is greatly increased, and thus an upper yield point is observed. In addition, theoretical analysis,9 as well as experimental observations, show that the upper yield point is strongly a function of temperature. The upper yield point is observed to decrease with an increase in testing temperature, and above a certain temperature (-700° K in iron) it no longer appears. This is consistent with the concept that thermal vibrations will help free a dislocation from its atmosphere, so that the external stress required to free a dislocation from its pinning atmosphere decreases with increasing temperature. Furthermore, with increasing temperature the equilibrium concentration of impurity atoms around a dislocation decreases exponentially with the result that the dislocation is less firmly pinned. In Cottrell&apos;s theory of yield point a static model is visualized in which the pinning atmospheres, particularly interstitial atoms, are immobile, and the dislocations are anchored to stationary positions in the lattice. However, experiments1,7 show the upper yield point to be time-dependent or a function of the rate of straining, a high strain rate causing a high upper yield point. Present theory does not adequately account for the rate dependence of the yield point, and the exact function of the interstitial atom is not under stood. Nevertheless, observation of the temperature dependence and rate dependence strongly suggests that the upper yield point phenomenon is due to the interaction between dislocations and pinning atoms, and that a diffusion mechanism is important in determining the yield point.

Jan 1, 1962

By M. E. Wadsworth, J. S. Cho

Colloidal silica dissolved in aqueous suspensions of high surface area thoria was permitted to adsorb on the thoria surface. Silica in three forms was identified by means of infrared spectroscopy and characterized by Si-O vibrational modes in the 9.0 to 10.5 region. A band at 9. 1 was attributed to free unad-sorbed silica, while adsorbed silica resulted in bands of greatest absorbency at 9.4 or 10.3p, depending upon the character of the surface bonding. Size considerations, the amount of silica adsorbed, and the character of the infrared spectrum for strongly adsorbed silica has been interpreted as evidence of formation of chain or layer silica linkages on the thoria surface. Infrared spectroscopy has been used successfully in recent years for the identification of minerals and synthetic inorganic substances. Unfortunately, infrared studies of silicate minerals have not proceeded to the point that unambiguous assignments may be made for Si-O vibrational modes as affected by lattice substitutions and structures. Several investigators have presented infrared spectra of silicate minerals, 1,7 and their work has pointed to the potential value of infrared to identify minerals as well as to note the sensitivity of various Si-O modes to structural and substitutional environments. The strong infrared absorption of various Si-O vibrational modes makes the infrared method a very useful tool for the study of silica adsorbed on the surface of solids of high surface area. Spaepen et a18 studied the adsorption of silica on thoria surfaces from aqueous solutions of silicic acid up to 300°C. A general review of the application of the infrared method to the study of surface adsorption has been presented by Pliskin and Eischens.9 EXPERIMENTAL Du Pont colloidal silica, Ludox SM (16.36% SiO2) and Ludox HS (30.25% SiO2) in aqueous suspensions were used as the sources of silica for the adsorption studies. The thoria used for this study was supplied by Union Carbide Nuclear Co.* under the preparation *Chemical Technology Div., Union Carbide Nuclear Co., Oak Ridge, Tenn. . number D-16-650. It was fired from the oxalate at 650°C and had a surface area of 32.4 ± 0.6 m2 per g measured by nitrogen adsorption. The chemical analysis of the D-16 thoria in ppm was: CO3= (5500), NO3- (< 4), so4±PO4 (100), and Si (20). The Ludox silica was placed in contact with the thoria in a two-liter autoclave10 between room temperature and 250°C. Slurries were made by placing 1 g of thoria in one liter of distilled water containing various additions of the silica sol. Samples were removed from the autoclave by opening a small stainless steel valve. Extracted samples were centrifuged for 10 min and excess solution was decanted. The sample was then dried for several hours at 80°C. Infrared samples were prepared by thoroughly mixing 10 mg of the thoria with 400 mg KBr in polystyrene vials on a "Wig-L-Bug" amalgamator. Pellets were pressed under vacuum and had final dimensions of 1.2 cm diam and 1.2 mm thick. Infrared spectra were

Jan 1, 1963